Tender For Construction Work Of Room With Toilet In District Judge Office - Earth work in excavation by mechanical means/manual means over areas(exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: all kind of soil. (DSR 2.6.1) 2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth leve 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) (DSR 4.1.5) 3 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand (DSR 6.2.1 ) 4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand (DSR 6.4.1 ) 5 Painting on DPC with two coat of air blown bitument 80/50 or 85/25 about 1.7 kg/sqm including ost of fuel if any.SOR New item 1 chapter 7 6 Reinforced cement concrete work in beams, suspended floors, roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). DSR 5.3) 7 Centering and shuttering including strutting, propping etc. and removal ( DSR 5.9.3) 8 M.S. (Tor steal or plain) in plain work such as R.C.C. or R.B. work including binding for proper shape and including supply of steel and its wastage bend hooks and authorised over lapping shall be measured. [S.I. No. 504] 9 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (DSR 21.3.2) 10 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 2nd class teak wood beading 62X19 mm. (DSR 9.51.1 ) 11 12mm thick plaster in 1:4 with cement & course sand . (DSR 13.4.1) 12 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.( DSR No. 13.80) 13 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than50 gram/litr (DSR 13.41.1) 14 Finishing walls with water proofing cement paint of required shade : 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm). (DSR 13.44) 15 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. DSR_13.85.3 16 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : ( DSR No. 13.99.1) 17 Supplying and filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete ( DSR No. 2.27) 18 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (DSR 11.41.2 ) 19 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (DSR 8.31) 20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with verticalgrains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. (DSR 9.20.2) 21 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.( DSR No. 9.127.2) 1.0 mm thick 22 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (DSR NO. 17.3.1) 23 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap (DSR no 17.7.2) 24 Providing and fixing white vitreous china flat back or wall corner lipped front urinal basin of430x260x350 mm or 340x410x265 mm sizes respectively (DSR NO. 17.23) 25 Providing and fixing white vitreous china squattind plate urinal with integral rim longitudinal flush pipe (DSR NO. 17.24) 26 Providing and fixing Chlorinated polyvinyl Chloride (CPVC) pipes having thermal stabilitiy for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing tha pipe with clamps at 1.00 m spacing this includes jointing of pipes & fittings with one step CPVC solvant cement and testing of joints complete as per direction of enginieer in charge. internal work exposed on wall . 15mm nominal outer dia pipes (DSR NO. 18.7.1) 27 Same as above but 20 mm nominal outer dia pipes. (DSR NO. 18.7.2) 28 Same as above but 25 mm nominal outer dia pipes. (DSR NO. 18.7.3) 29 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (DSR NO. 18.51.1) 30 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore (DSR No. 18.49.1 ) 31 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (DSR No. 18.53.1 ) 32 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32mm dia (Semi rigid pipe) (DSR No. 17.28.1.1 ) 33 Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore(DSR No. 18.21.2 ) 34 Providing and fixing PTMT grating of approved quality and colour. Circular type. 100 mm nominal dia. (DSR No. 18.58.1.1 ) 35 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with CP brass screws and washer complete (DSR No. 17.31 ) 36 Providing and fixing gun metal gate valve with C.I. wheel of approved quality 25 mm nominal bore (DSR No. 18.17.1 ) 37 Providing and fixing ball valve (brass) of approved quality, high or low pressure with plastic float complete. 25 mm nominal bore (DSR No. 18.18.3 ) 38 Providing and fixing PTMT soap container 109 mm wide, 125 mm high and 112 mm distance from wall and standerd shape with breacket of same material with snap fitting of approved qulity and color, weghing not less than 105 gm (DSR No. 17.71 ) 39 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum 37 mm distance from wall face with concealed fitting arangement of approved quality and color, weighing not less than 88 gm(DSR No. 17.72 ) 40 Providing and fixing S. W. intercepting trap in manholes stiff mixture of cement mortar 1:1 including testing of joints complete 100 mm dia(DSR No. 19.34.1 ) 41 Supply and fixing of 10cm internal dia PVC pipe, 6kg/per sq.cm. preasure make complete with bends with door at top and plain at bottom and grating and including supply of necessary M.S clamps 2.5cm x3mm fixed to walls with and including supply of 15cm long 6mm dia nails all material labour and T&P etc Required for completion of the work and also includkng repair of plaster pointing etc. If damaged during fixing of the pipe.si-730A 42 Providing and placing on terrace polythylene water storage tank ISI: 12701 Marked with cover and suitable locking arragemant and making necessary hole for inlet, outlet and overflow pipes without fittings and the base support for tabk. (DSR No. 18.48) 43 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (DSR N0 19.1.1) 100 mm diametre 44 Constructig brick masonry mainhole with cement mortar 1:4 (1 cement:4 course sand) with RCC top slab in 1:1.5:3 mix (1 cement : 1.5 course sand (zone-III) : 3 graded stone aggregate 20 mm nominal size ), foundation concrete 1:4:8 mix (1 cement : 4 course sand (zone-III): 8 gradad stone aggregate 40 mm nominal size), inside plastring 12 mm thick with cement mortar 1:3 (1 cement : 3 course sand), finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 internal dimensions total weight of cover and frame not less than 38 kg with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(DSR No. 19.7.1.1) 45 Making soak pit 2.5 m diameter 3.0 m depth 45x45cm dry brick honey comb shaft with bricks S.W. drain pipe 100mm diameter, 1.80m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(DSR No. 19.32.1) 46 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(DSR NO. 10.1) 47 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 f ine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).(DSR 14.88) 48 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit ,piano type switch, phenolic laminated sheet, suitable size M.S. boxand earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A (DSR 2022 1.8.1) 49 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2X 1.5sq. mm + 1 X 1.5 sq. mm earth wire (DSR 2022 1.14.1) 50 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2X6 sq. mm + 1X4 sq. mm earth wire (DSR 2022 1.14.4) 51 Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.(DSR 2022 1.29) 52 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 12 way , Double door(DSR 2022 2.3.3) 53 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole (DSR 2022 2.10.1) 54 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation : B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, with remote orelectronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. (DSR 202219.1) 55 S/F of 18 -22 W LED batten fitting with extruded Alluminium housing ,special polycarbonate diffuser for glare free light distribution and suitable mounting for on both surface & suspended. complete in all respect.1980-2420 system lumens,> 110Lm/W. PF>0.95, THD<10% ,CRI>80 with 3 year warranty. Cat AA (SOR 23.08) 56 S/F of LED Bulb 12 Watt
