Decorative Glazing And Acp Works At The Administrative Building (P-1) Under Bolpur Municipality.- 1 Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars.(a) In ground floor including roof. 2 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. (a) In ground floor including roof. 3 Dismantling all types of plain cement concrete works, stacking serviceale materials at site and removing rubbish as directed within lead of 75 m. In ground floor including roof. (a) Upto 150 mm thick.. 4 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).(f) 25 mm to 30 mm shuttering without staging in foundation 5 Ordinary Cement Concrete (mix 1:2:4) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevent IS codes. (a) Pakur Variety 6 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary(Ground floor).[Excluding cost of chipping over concrete surface].(i) With 1:6 cement mortar (c) 15 mm thick plaster 7 Brick work with 1st class bricks in cementmortar (1:6). (a) In foundation and plinth 8 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodisedconforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge. 10-12 Micron thickness Annodizing filmNatural white (for estimate purpose construction wing may consider weight of 2- track Aluminium window @ 5.5 Kg per Sq.M.and 3-track Aluminium window @ 6.5 Kg per Sq.M] 9 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.iv) 5mm thick coloured / tinted / smoke glass. 10 Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge 11 M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section,consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.I) For structural members of specified sections weighing less than 22.5 Kg./mStructure with Equal Angle(50x 50 x 3 ) mm @ 2.3 kg/m 12 (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing 10 Kg./sq.mtr upto 16 Kg./sq.mtr 13 (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 14 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With super gloss (hi-gloss) -With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white) 15 Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surfacearea of ACP)b) 4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating) 16 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.xiv) 12mm thick coloured / tinted / toughened glass coforming to IS: 2553-1992 (Part-II) 17 Supplying profiles of required sections made of aluminium alloy extrusion confirming to IS 732-1983 and IS 1285-1975 anodised with required film thickness and specified colour / natural mat finished conforming to IS 1868-1983 for fabrication of structural glazing, curtain wall formed of basic section of any ISI embossed / certified make and brand as per direction of Engineer-in-Charge. (Payement will be made on finished length of the work). for Structural glazing / curtain wall with15 micron Coloured Anodising(i) Fixing Plate (Wt. @ 0.515 Kg per Mtr.) 18 Labour charge for fabrication and installation of structuralGlazing/Curtain Wall made from annodized extruded allooy aluminiumsections for the following units:-Structural Glazing made of extruded and annodized alloy aluminium sections, fabrications including cutting to proper shape and size, drillingincluding cost of brackets, fastener bolt, mullion bolt, nuts & washers, maskin tape, double side adhesieve crosslink foam (used for guard of glazed silicon on sub-frame), tissue paper foam (used as filler between sub-frame and under backing of weather silicon), screws and other necessary hardwares, fixing of glass as per drawing, specification and direction of Engineer-in-Charge. (The rate includes hire charges of all tools and plants, including all incidental charges, adhesieve, joiners such as screw,cleate angle,etc. but excluded the cost of extruded aluminium sections, glass, glazed silicon, weather silicon etc.) 19 ADD 18 % GST 20 ADD 1% CESS
