Tender For Provision Of Tech And Otm Accommodation For Mdc At Meerut; 1 SCHEDULE A PART - I (BUILDING WORK) 2 Construction of Tech Accn for MDC (Double story) including paved area for pateint parking adjecant to the main bldg complete all as specified and shown on drawings. 3 Construction of OTM Accn for MDC (Double story) consisting of MT garrages for unit veh, Covered parking space, Storage Accn, Single living Accn for 06 Havs & 11 Ors, Drying & ironing shed, Cook house, dining hall and duty room complete all as specified and shown on drawings. 4 Construction of ETP for MDC (Single story) complete all as specified and shown on drawings. 5 Construction of Flag Mast complete all as specified and shown on drawings. 6 Construction of Garbage bin complete all as specified and shown on drawings. 7 SCHEDULE A PART- II (Internal Water Supply) for details refer Sch A in pdf folder 8 SCHEDULE A PART - III A (Internal Electrification) for details refer Sch A in pdf folder 9 SCHEDULE A PART - III B (Internal Electrification) 10 M & L for point wiring using 1.50 sqmm size, PVC insulated, unsheathed 1100 volts grade, IS-694 single core multistra-nded (FRLS-H) copper conductor cable in proper colour coding drawn into and including non metallic rigid PVC conduit medium grade (not less than 20 mm dia) with and including its all necessary fittings and accessories fixed concealed, sunk cast iron or 1.6 mm thick pressed modular steel terminal box for mounting fittings i.e. modular switch /sockets including cover plate with frame including one continuous run of PVC insulated (green colour) 1.50 sqmm size stranded FRLS-H copper conductor cable as in earth wire and connecting all metal parts to common earth dolly including cutting and chases pinning in for concealed conduit wiring and making good of disturbed surface complete all as specified and directed for the following: - (Note: Rate for modular plate and frame is deemed to be included in quoted rate) 11 (a) One light point /bell buzzer/ ceiling fan / Exhaust fan point controlled by one-one way switch. 12 (b) One three pin 5 Amp socket on same board with other switches. 13 (c) One three pin 5 Amp socket on independent board 14 All as per item No 4.1 above, but point wiring with cable 2.5 Sq mm size, with earth continuity conductor of size 2.5 Sq mm for one 3 pin socket outlet 15 Amp independent 15 All as per item No 4.1 above, but point wiring with cable 4.0 Sq mm size, with earth continuity conductor of size 4.0 Sq mm. 16 Supply & fixLED lamp 12 watt, 220 volt AC decorative type connecting up with three core flexible copper conductor of suitable size from ceiling rose complete all as specified and directed. 17 Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as requiredcomplete all as specified and directed. 18 Supply & fix water heater storage type 5 star rating 25 ltr capacity complete all as specified and directed. 19 SCHEDULE A PART - IV A (Site Clearance and Earth work) for details refer Sch A in pdf folder 20 SCHEDULE A PART - IV B (Site Clearance and Earth work) 21 Supply selected/ approved earth brought from outside the site and filling the same in plinths, back of retaining walls, foundations and trenches and spreading in landscaping and other location as directed by the Project Manager and shall be done in layers, not exceeding 20cm in depth and consolidating each deposited layer by mechanical means, ramming and wateringas per specifications including transportation, cost of soil, royalty, loading, unloading, carriage to dumping spot and all incidentals at all depths and levels, for all leads and lifts complete (Net consolidated area fill volume will be computed from the initial and final levels. Volume in slopes, embankments etc. will be computed applying appropriate formula, as per MES specification). 22 SCHEDULE A PART - V A (Road, Hard standing & Culvert) for details refer Sch A in pdf folder 23 SCHEDULE A PART - V B (Road, Hard standing & Culvert) 24 S&F ABS body cat eye Road stud of size 100 mm X 100 mm x 20 mm of yellow / orange / red colour IRC67 having load capacity of 40 ton of having reflector on both sides fixed with epoxy on road complete all as specified and directed. Make - Tata BP/Dark Eye all as per manufactures instructions complete all as specified and directed. 25 S&F Box type Glow Sign Board of size 1.2 mtr x 1.5 mtrs, made out of angle iron framed and fixed of white / coloured acrylic cover both side (front & rear) complete openable including one number FTL fitting 2x40 Watt fixed inside board and connected with 3 Core Cable 4 Sqmm from nearest electric point to the board and controlled by one MCB SPN 10 Amp complete including writing work complete all as specified and directed. 26 SCHEDULE A PART - VI A (Sewage Disposal) for details refer Sch A in pdf folder 27 SCHEDULE A PART - VI B (Sewage Disposal) 28 M&L for soakage well excavation in ordinary soil foundation in PCC 1:3:6 walls of honeycomb masonary with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slabs in M-25 / SFRC cover interconnecting pipe of RCC / DWC complete filled with brick bats of size 2.40 m x 6.00 m complete all as specified and directed and as shown on drawings. 29 M&L for construction of RCC septic tank of 100 users excavation in any type of soil foundation in PCC 1:2:4 RCC wall and slab covers including RCC precast manhole covers having 6m plate embeded all around / fabric reinforced cover with angle iron frame vent shaft and sludge chamber etc complete all as specified and directed and as shown on drawings. 30 SCHEDULE A PART - VII (Area Drainage) for details refer Sch A in pdf folder 31 SCHEDULE A PART - VIII A (Compound Wall, Fencing & Gate) for details refer Sch A in pdf folder 32 SCHEDULE A PART - VIII B (Compound Wall, Fencing & Gate) 33 S&F precast concrete compound wall 2.10m height using precast members such asI section post 150mmX150mm, prestressed with 07 Nos of prestressing steel of 3 mm dia and RCC plank 2100mm X 300mm X 50 mm prestressed with 04 Nos of 3 mm dia prestressing wire with taking care all necessary steps including levelling etc to erect the structure complete all as specified and directed. 34 SCHEDULE A PART - IX A (External Water Supply) for details refer Sch A in pdf folder 35 SCHEDULE A PART - IX B (External Water Supply) 36 S&F gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends for iron pipeconforming to IS 9338, 80 mm (2) dia complete all as specified and directed. 37 M & L for construction of brick masonrypit chamber of folloiwng internally size 450 mm x 450 mm x 450 mm with angle iron frame of sizes 40 x 40 x 5 mm thick mild steel plate cover painted with two coats of sythentic enemelled paint over a coat of red oxide primer after preparation of surface incl locking arrangment and necessary excavation and earth work 80 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate over 100 mm thick hard core using brokenin foundation brick work in cement mortor 1:6 and 15 mm thick cement plaster in cement mortor 1:4 in internal surface of walls and outside upto 150 mm deep below ground level complete all as specified and directed at site. 38 SCHEDULE A PART - X A (EXTERNAL ELECTRIFICATION)for details refer Sch A in pdf folder 39 SCHEDULE A PART - X B (EXTERNAL ELECTRIFICATION) 40 S&F Cable route markers made of GI with supporting GI angle of size 40 X 40 X 6 mm for stand and plate size 150 X 50 X 5mm thick and primering, painting, writing of HT/LT cable route mark for suitable size letters including M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregates in mass concrete or plinth block complete all as specified and directed. 41 Providing platform for transformer of size 3.0 x 3.0 x 1.0 m high from GL including excavation in trenches not less than 1 mtr, PCC 1:5:10 type E2 for foundation, brick work in cm 1:6, PCC 1:2:4 type B1 in copping, plaster 10 mm thick in cm 1:6 om brick /complete surface PCC 1:4:8 type B1 sub base 75 mm thick, as in flour PCC 1:2:4 type B1 100 mm thick floor using extra cement returning filling and removal on surplus soil, chain link fencing 1.8m high made out of 4 mm dia GI wire 150x100 mm mesh MS work angle iron 50x50x6 mm as fencing post in embeded in brick /PCC work at 2 mtr interval each side as approved 1 No steel gate (3.5 m clear) span as shown in drawing with locking arrangement made out of 15 mm dia MS rod and 50x50x6 mm angle iron frame. painting with 2 coat aluminium paint over a coat of red oxide primer and 3 coats of white washing on cement work including 2 Nos ISMB 100 mm chanel for fixing transformer including ramp of suitable size mounting of transformer complete all as specified and directed. 42 Supply, Installatiion, Commissioning of transformer of capacity 250 KVA step down outdoor type copper wounded 11/0.433 KV (at no load) AC 3 phase 50 HZ on secondry side double wounded oil immersed naturally all air cooled with external cooling tubes/ rediator, delta connected as on primary and star connected with netural brought on secondry) side and having tapping at (-+) 2.5%,(+_) 5%(+_) 7.5% to be changed by hand operated OFF LOAD top changing gear. The maximum temperature rise should not exceed 45 degree centigreade in oil and 50 degree centigrade in HV/LV winding when measured by the resistance method after contineous full load run in ambient temprature the transformer shall confirming to IS 2026. 2011 Part-1and comprising of following accessories:- (a) Three Nos porcelain bushing with arching horn on HV side suitable for 11 KV complete with bushing copper rods nuts and washers (b) One cable box on LT side (secondary side) consisting of four Nos porcelain with copper bushing rods complete with nuts and washers with one No cable glands suitable for reception of taking out 01 Nos 3.5 core 400 Sqmm LT 1100 Volts grade PVC sheathed and PVC insulated heavy duty armoured cable including gland joint and jointing materials complete. (c) Oil conservator with filter type drain valve and oil level gauge. (d) Dehydrating breather with first fill dehydrating agent (Silica jal) (e) Explosive vent(f) Thermometer pocket on tank cover(g) 01 No 100 mm dia dial type thermometer vapour pressure type having range (0-120) degree celsius with metal guard having maximum temperature indication with resisting device for transformer.(h) Two earthing terminal on tank cover to facilitate fixing of 32x6 mm GI earth strip(i) Rating plate and terminal marking plate.(j) Oil level gauge.(k) Oil drain filter valve.(l) Lifting lungs.(m) Oil filling hole with cap/plug with connection plate complete.(n) Air relief valve plug (o) FourNos plain solid cast steel detachable rollers. (p) Extra bushing for neutral out side the cable box providing independent earthing for neutral. (q) First fill of fresh transformer oil conforming to relevant IS tested up to 60 KV dielectric strength at 2.5 mm gap 43 Supply installation testing and commissioning of LT feeder pillar box (KIOSK) type totally enclosed made of MS sheet 3.15 mm thick outdoor type weather proof having sloping canopy with both side openable, locking arragement and painting etc (factory made) comprising the following:-(i) Incoming MCCB 420 Amps 4 pole415 volt 50 KA -1 No.(ii) Outgoing MCCB 320 Amps TPN 415 volt 36 KA -2Nos (01 spare) (iii) Outgoing MCCB 63 Amps TPN 415 volt 25 KA -03Nos(01 Spare)(iv)) Outgoing MCCB 32 Amps TPN 415 volt 25 KA -02 Nos(v) Outgoing MCB 32 Amps SPN 230 volt 25 KA - 03 Nos (01 Spare)(vi) Busbar aluminium 500 Amps with air insulated for TPN(vii) Indicator lamp LED type- 3 Nos. 44 (viii) Digital Multifunctional panel mounted meter with CT secondary site selectable 1A/5Ain accuracy class 1.0, CT primary programmableand display phase to phase voltage, phase to neutral, instatanious average, maximum and total load current, Active powet KW , Rective power KVAR and apparent power KVA, instantanious and total power factor, frequency RS 485 communication (optional)(ix) Timer switch with contactor TP 20 Amp for street light fittings.-02 Nos(x) Panel wiring with 2.5 Sqmm copper cable PVC single core -1 Job.(xi) PCC plateform with foundation 1:2:4 = 1 job. 45 Supply, Fabrication, Installatiion, Testing & Commissioning (CPRI approvied) 440V AC LT APFC Panel 100 KVAR capacity (50+25+15+5+5) or suitable sizes combination including incoming controls, outdoor type, compartmentalized, Modular Indoor Type in 2.0 mm CRCA Sheet of appropriate size, Front Operatable Double Doors, (Front & Back Openable), Dust & vermin proof, cable entry though 2.0 mm CRCA gland plates at bottem, powder coated, 3 Phase HR sleeved color coded aluminium main bus bar of 400 A -3 Nos with transparent FRP covers & on SMC / DMC supports, 25 x 6 mm aluminium earth bus bar running across the whole length of the LT Panel with 2 Nos. Studs at both the side-ends, Lifting arrangment / hooks at the top, wiring with appropriate size of Copper industrial cables, black painted base frame - 40 x 40 x 6 mm MS angle complete all as specified and directed. 46 S&F Sintex FRP type junction / looping box of size 280 x 170 x 130 mm top hinged with aluminium busbar of 50 Amp rating for phase and neutral on porcelain based insulator, fixed on pole with the help of MS nuts, bolts and MS clamps 02 Nos of size 40 x 4 mm thick with one No MCB SP 6 Amp capacity mounted, factory made duly painted powder coating process complete all as specified and directed. 47 M&L for pole box fabricateed out of 1.8mm thick MS sheet having 3 nos busbar 50Amp copper conductor mounted on insulators one no 20x3mm copper bus bar with 2 clamps of copper strip for earthing of the armoured of the cable complete with making holes for connecting cables etc nuts bolts etc size of box not less then 100x200x80mmfront openable hinged cover suitable for mounting on steel using clamps nut bolt etc pvc adopteers and PVC hose pipe upto cable trench for incoming and outgoing cables, factory made duly painted with powder coating process complete all as specified and directed. 48 Excavation by trenchless tech, Boring of holes under road pavement, hard standing by srencheless techonology using ultra sounding rechnique and necessary machine including HDPEpipe of 150 mm dia suitable for 0.4 Mpa working pressure. 49 Supply, installation, testing and commissio-ning of silent diesel engine DG Set 415 Volts, 3 phase 4 wire engine as per IS 10001/10002 and alternator as per IS 13364 complete with necessary foundation as per manufacturer recommendations. AVM pads control panel with necessary meters and sound proof canopy of capacity upto 200 KVA complete all as specified and directed for the following specifications :-(A) DIESEL ENGINE :-Water cooled, 6 x cylinder (83 BHP) @ 1500 RPM, Engine shall be cooled by rail mounted, engine driver radiator of adequate capacity, with blower fan, fan guard, self regulated electronic governor and fan belts etc. 50 The diesel engine shall be vertical, to run continuously at 1500 RPM confirming to IS 10002, BS-5514, standard with overload capacity of 10% for one hour in every 12 hours of operation. Diesel Engine shall be comply with latest CPCB Norms. Make of Engine- CUMMINS, KIRLOSKAR, GREAVES COTTON, ASHOK LEYLANd.(B) ALTERNATOR :- Alternator 200 KVA, suitable to deliver rated output at 1500 RPM, 415 Volt, 0.8 PF (LOG), 50HZ, 3 PH, in SPDP enclosure, self excited and self regulated electronic governer. The alternator shall conforms to IS-13364 and shall be suitable for tropical condition. Full load efficiency of the alternator offered should be above 90%, insulation and temperature rise also limited to class-H. Enclosure shall confrim to IP-23. Make of Alternator- KIRLOSKAR, CATTERPILLAR, STEMFORD, JYOTI, CROMPTON GREAVES, NGEF (C) STANDARD CONTROL PANEL. Totally enclosed, steel construction control panel comprising of follwings :- 51 (i) Main on/ off MCCB 3 phase 4 pole 415 Volt, 50Hz 100 Amp rating - 01 No.(ii) Phase indicating lamps set of three -01 No.(iii) Instrument fuse - 01 Set.(iv) Digital Display /indication of engine and alternator parameters as mentioned below :-(a)Lube Oil Pressure.(b)Battery Voltage.(c)Engine RPM.(d)Fuel Level in the Tank. 52 (e)Engine Running Hours Indication.(f)AC Current and Voltage.(g) AC Frequency.(h) AC Power Metering.(j)Suitable CTS for displaying the electrical Parameters.(C)OUTDOOR AMF PANEL:- (a) MCCB TPN 125 AMps 25 KA - 2 Nos (incoming)(b) Contractor 4 pole suitable for 125 Amps - 02 Nos(c) MCB SPN 32 10 KA - 01 No (outgoing)(d) Voltmeter & ammeter digital multi functioning 0-500 V - 02 Nos (incoming and outgoing)(e) Selector switch - 03 Nos (Manual AMF mode & DC ON/OFF)(f) Indicating lamps (RYB) - 03 set(g) PCC foundation (Civil works) for grouting of AMF panel(h) AMF relay 24/12V DC - 04 set(j) Automatic battery change unit fixed in AMF panel - 01 No(k) Copper wiring and lugs suitable size for internal wiring of AMF panel(l) Bus bar 300 Amps for RYBN(m) AMF logic controller for 125 Amps 53 SCHEDULE A PART - XI A (AC, WATER COOLER & DESERT COOLER)for details refer Sch A in pdf folder 54 SCHEDULE A PART - XI B (AC, WATER COOLER & DESERT COOLER) 55 Supply and install hi wall splitAC units indoor/ outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 complete for the following capacity:- 56 (a) 1.5 TR 57 (b) 2 TR 58 (c) 3 TR 59 Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% complete all as specified for the following capacity :- 60 (a) 1 KVA 61 (b) 2 KVA 62 (c) 4 KVA 63 (d) 5 KVA 64 Supply, installation and testing of 310 Litres capacity Refrigerator (5 star rated)with non CFC refrigrent type, electric driven single phase, frost free, double door, air cooled having sealed unit compressure complete all as specified and directed. 65 Supply and installation of desert cooler made out of 1 mm thick PGI sheet, painting etc.electric driven, 450 mm sweep heavy duty copper wounded motor, single phase air flow capacity 3000 Cum/Hrs (Tank capacity 200 ltrs) submersible pump etc complete all as specified and directed. 66 SCHEDULE A PART - XII (CABLE NETWORKING)for details refer Sch A in pdf folder 67 SCHEDULE A PART - XIII (Hot Water Supply)for details refer Sch A in pdf folder 68 SCHEDULE A PART - XIV A (ARBORICULTURE)for details refer Sch A in pdf folder 69 SCHEDULE A PART - XIV B (ARBORICULTURE) 70 Providing and planting Duranta Golden hedge, having height.15 cm to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot complete all as specified and directed to the entire satisfaction of Engr-in-charge. 71 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth shall be paid for separately.) 72 Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 Km lead complete (Cattle manure measured in stacks will reduced by 8% for payment.) 73 Supply and stacking approved cultivated earth (sweet earth) at site free from grit, stone / brick chipps particles, grass roots and other foreign particle and screened at site including royalty and carriage upto 5 Km lead complete (earth measured in stacks will be reduced by 20% for payment).NOTE:- The earth shall be approved by GE before supply and shall be deposited in stacks for measurement purposed as directed. 74 Supply and planting well grown disease free plants (including cost of plants / trees/ shrubs) as appended below including preparing beds not less than 60 cm dia and digging hole upto a suitable depth (not less than 60 cm) as per plant species and ground earth condition fron the adjoining ground level, mixing and laying of sweet earth and manure in ratio of 2:1 and surface dressing, watering for suitable period of time till its healthy growth and further germinations completed all as specified and directed:- Notes :- Sweet earth shall be measured and paid separetely as supply only. The supply of manure and other supported works shall deemed to be included in quoted rates. The manure shall be prepared as per indian standards. 75 Ashok trees (105-120 cm height) 76 Mango trees (60-65 cm height) 77 Gulmohar trees (150-165 height) 78 Bottle Palm (height 150-180 cm, bottom girth 20-25 cm) 79 Araucaria cookii / Christmas tree (75 to 90 cm height) 80 Taiwan pink Guava (60-65 cm height) 81 Jamun (150-165 cm height) 82 Amaltash (120-135 cm height) 83 M&L for anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area including cost of chemical complete all as directed. 84 M&L for planting Bermuda /Rajghat/ Doob, Selection No. 1 grass roots @ 75 mm c/c both ways in lawns/ parks/ gardens etc including perparation of surfaces by ploughing ground, perparing and laying bedding mixed with sweet earth, sand and manure in suitable proportion, watering and levelling the surfaces complete all as specified and directed. Notes:- (i) Sweet earth shall be measured and paid separetaly as supply only. The supply of manure and other supported works shall deemed to be included in quoted rates. The manure shall be prepared as per indian strandards.(ii) The 25% quoted rates shall be deemed to be included maintenance of lawn till grass forms a thick layer free from unwanted vegitation, weets to the entire satisfaction of Engr-in-charge. 85 Supply and fixing of brass oscilating sprinkler suitable to fix in 15 mm / 20 mm bore GI pipe ISI mark for watering the area of grass lawn complete all as specified and directed. 86 S&F CP brass bib cock with nozzlesuitable for 15 mm bore pipe including necesary fittings, etc of Make : Essco or equivalent make complete all as specified and directed. 87 S&F powder coated three seater Cast iron garden bench (black) make it deal for outdoor purpose, high quality structure, water and UV resistant of size length (63 inches), width (30 inches) & height (27 inches) and weight not less than 60 Kg complete all as specified and directed. 88 Supply and installation, testing and commissioning manufacturers factory assembled and tested, electric motror driven monoblock water pump 1 Hp (0.75 KW) capacity, comprising of heavy duty, copper wound motor, cost iron body with broonze impellor, casing ring, sleeves etc the scope of work also includes the PCC foundation of the pump set as per manufacturers recommendations, GI earthing of pump, MS bolts with nuts, raining protection cover. The scope of work also includes the following: -(a) GI pipe of suitable dia, heavy grade in sutable length, but not less than 5 m and taper connection piece.(b) GI delivery pipe of suitable dia for heavy grade in suitable length, but not less than 2 m and taper connectiong piece.(c) CI foot valve with leather washer of suitable size, lift and swing single door. 89 (d) Fabrication, supplying, installation, testing and commissioning of electric control panel outdoor type fabricated out of 3.15 mm thick CRCA sheet compartment-alised with hinged lockable doors dust and vermin proof powder coated of approved shade after 7 tank treatment process having switch gerars and accessories mounting and internal wiring earth terminals, numbering etc complete in all respect suitable for operation on 415 V3 phase, 50 Hz AC supply with enclosure comprising the following:- (i) MCCB 4 pole 25 Amps 25 KA adjustable type- 01 No (incommer) 90 (ii) Digital voltmeter 0-500 V with selector switch - 01 No (iii) Digital ammeter 0-100 Amps with selector switch - 01 No (iv) Set of 3 phase RYB indicator- 1 Set (v) Fully automatic delta starter 01 HP pump - 01 No (vi) Selector switch for local / remote auto / manual / off operation (vii) PVC bedded, wire armoured, electric power cables. (heavy duty with stranded aluminium conductor 1100 volts grade 6 Sqmm, 4 Core) - 15 RM 91 SCHEDULE A PART - XV (Medical Gas Pipe Line) 92 S&F Copper pipes of the following sizes:- Copper tube Should be soiled drawn seamless deoxidized, nonarsenical, half hard, tempered and degreased as per BS EN 13348 : 2001 duly supported with manufacturer test certificates for physical properties and chemical composition. The Tubes should be supplied with Third Party Test Certifications like LLOYD / TATA / SGS / CITCO. Every tube should have batch No. according to test certificates.Makes: MEXFLOW / JANYA / WEDNESBURY 93 (a) 12 mm 94 (b) 15 mm 95 (c) 22 mm 96 (d) 28 mm 97 SCHEDULE A PART - XVI (Fire Fighting) 98 S&F of portable Fire Exitinguisher A B C powder type 5 Kg capacity wall mounted type wall brackets complete in all respect discharge range from 4 to 6 Mtrs in 15 to 20 sec, testing pressure 30 Kgf/cm² ISI marked complete all as specified. 99 Supply and fixing Fire Beaters with 20 feet long handle with duly painted with red enamel paint complete all as specified. 100 Supply and fixing sheet metal fire buckets duly painted with red enamel paint and written FIRE on bucket complete all as specified and directed. 101 Supply and fixing Fire Axe with suitable length handle duly painted with red enamel paint complete all as specified. 102 Supply and fixing Fire Hooks with 20 feet long handle duly painted with red enamel paint complete all as specified. 103 SCHEDULE A PART - XVII (Misc Items) 104 S&F 1 mm thick Lead sheet pasting on wall to wall up to 3.00 m height complete all as specifieds and directed. 105 S&F 2 mm thick Lead sheet pasting on door (Two Nos of door) complete all as specified and directed. 106 S&F BEP automatic sensor tap (Battery) includes chromimum plated solid brass body tap T10 & ABS plastic body control unit with inbuilt valve complete all as specified and directed. 107 Supply, installation, testing and commission-ing of Sliding Glass Door Opener (Max. Load 100 KG per Door Leaf) SGD 304 (Max Door Opening : Single Door Leaf 7 Ft, Double Door Ft each) Kit includes : Motor with Gear & Control Box, Remote and accessories complete all as specified and directed. 108 S&F Electric Chimney 60 cm 1200 cum/ hr auto clean covered glass kitchen chimney, filterless technique including motion sensor and touch control (for cveramic room and casting room) complete all as specified and directed. 109 Supply, installation, testing and commission-ing of commercial air curtain unit for prevention of dust and conditioned air losses, three phase 440 V, 50 Hz made out of MS / CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven backed) with MS CRC 18 gauge square perforated suction grills, aluminium alloy fans and single phase electric motor, nozzle etc, complete with fittings and accessories so as to produce 1-1.5 m/ sec air velocity at floor level for door opening size 70x90 complete all as specified and directed. 110 Supply and fix Lift electrically operated Microprocessor controlled complete with power driven automatic stainless steel (SS) sliding doors and having SS car enclosure, suitable to carry 8 passanger (544 Kg) at a speed of 1.0 M/s to serve upto 1 floors (G+1st floors), Battery operated Emergency alarm bell, Fire man switch at main lobby, automatic rescue device, floor announcement system complete all as specified and directed. Elevator Shaft: Car travel G+1st floors, Nos of stops and openings -2, Shaft size 1700 mm (width) x 1900 mm (depth), Pit depth 1500 mm and over head 4500 mm.Cabin specification: Stainless steel cabin in standard designer hairline mirror finish, car size 1300 mm (width) x 1100 mm (depth) x 2200 mm (height), Car entrance 800 mm (width) x 2000 mm (height), Car door - Stainless Steel Two 111 panel center/ telescopic opening auto car door in standard hairline finish having down curtain infrared door safety, PVC flooring, stainless steel designer false ceiling, LED light and axial floor fan or blower, ilIuminated buttons with 7 segment direction and position indicator.Doors: Stainless steel 2 panel center/ telescopic opening auto landing door in standard hairline finish at all above landings, clear opening 800 mm (width) x 2000 mm (height). Illuminated buttons with 7 segment direction and position indicator.Machine: Gearless machine, main power supply 415 volts, three phase 50 Hz A.C., auxillary supply system 220 /230 volts single phase 50 Hz A.C., Simplex down collective system, AC VVVF drive. 112 Supply and fix Effluent treatment plant of capacity 2 KLD including all connected items, accessories etc including civil work complete all as specified and directed with the following specifications:-Skid amounted nano ETP continuous flow process semi automatic. Mechanical Work: MS SKID with frame 1250 x 2000 x 2400 mm height M.S. fabrication - 01 set, M.S. settling tank / clarifier with ladder 1000 mm dia x 1250 mm height MS FRP - 01 set, Multi media sand filter vessel PENTAIR 1354 with FRP filter with fine and coarse media - 01 set, Activated carbon filter vessel PENTAIR 1354 with FRP filter with media and activated carbon, Chemical Dosing tank (03 Tanks) of size 113 400 mm x 400 mm x 1200 mm length MS FRP capacity 60 Ltrs each - 01 set, Filter Feed Tank of PVC capacity 300 Ltrs - 01 Set, Sludge drying bed of MS fabrication size 500 mm x 1000 mm x 500 mm height, Airation system of coarse and fine bubble diffusers - 01 lot, UPVC piping fittings multiport valves etc. - 01 lot.Chemical for ETP: Hydrated lime 15 Kg,Feric alum 15 Kg, Poly electro-lyte 100 Gm, PH Paper - 01 box.Electrical Works: Effluent transfer pump set 0.5 HP - 01 set, Filter feed pump set 0.5 HP - 01 set, Air blower 2 HP - 01 set, Electrical MCB box - 01 set. 114 Monitoring Equipment: Dosing pumps (0-6 Ltrs) (mini dose /E-dose) - 01 set,Water flow meter (Rota Meter) - 01 set. Biological Technology: Bio pack media pharmatech 01 cum - 01 set.FRP Coating and Paint: Effluent treatment plant internal surface coating and outer paint FRP coating 0.5 mm surface mate on MS fabricated setling tank, SBD, Dosing tanks.
