Tender For Repair And Renovation Works For Setting Up Of Ssk At Ahiran Masjidpara Sc, Suti-I Block, Murshidabad-- 1 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including remo ving, spreading or stacking the spoils within a lead of 75 m. as directed.(a) Depth of excavation not exceeding 1,500 mm. 2 Earth work in filling in foundation tren ches or plinth with good earth, in lay ers not exceeding 150 mm. include ing watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)With earth obtained from excavation. 3 Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.Found,Toilet 4 I) Cement concrete with graded stone ballast (40 mm size excluding shuttering)(A) [Pakur Variety](a) 1:3:6 proportion 5 A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed with water, ramming complete including the cost of supply of sand. 6 Taking out M.S. or W.I. Grills from wooden frame including cutting lugs from masonry wall and refitting the same and mending good damages after repairs. (Excluding the cost of necessary repair of damages) or doing any other necessary works. 7 (A) Stitching crack in brick wall by carefully cutting out face brick 125 mm. deep into the wall, cleaning the gap and filling up the same with precast cement concrete block carefully set in cement mortar (1:3) including mending good damages and finishing the surface to match with adjacent areas complete as per direction.(i) With plain cement concrete blocks(1:1½:3) with stone ,chips.(a) Block size 250 x 125 x 75 mm.,In GR.Fl 8 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.A) Ceiling Gr.Fl,Store.WC,Passage,EX Room,B) In side Wall, Gr.Fl,Store.WC EX. Room,Less D3,O. Room,C) Out Side Wall,Gr.Fl,EW,Back,Total Gr. Fl............. ( A+B+C) 9 D) Ceiling 1ST .Fl,Store.WC,Passage,D) In side Wall, O. RoomStore. 1ST.Fl,WC,EX. Room,Deduction,D3,W3,E) Outwall-1ST .Fl,Total Gr. Fl............. ( D+E+F) 10 Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m. a) In Gr. floor ,G.F,Store,Passage,D2,WC ,Door Seal,EX Room,Office,E.Room, Door Seal, 11 In 1st Floor,G.F,Store,Passage,D3,WC ,Lab,Door Seal,EX Room,Office,E.Room, Door Seal, 12 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceablematerials at site and removing rubbish as directed within a lead of 75 m.In Ground Floor , Store wall,Exhaust,V1,For pipe line,Groove 13 In 1st Floor,Add D2 14 Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.(a) upto 150 mm. thick,In ground floor including roof. 15 In 1st floor including roof. 16 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.,a) Pakur Variety, Gr.Fl (06 km) 17 At 1st. Fl. 18 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. In Gr.Fl,(i) Pakur Variety, 06 Km,Tie beam,Lintel beam,Top sink,Blood Collection,Sitting Slab,Chajja 19 In 1st Floor,Lintel beam,Top sink,Lab Lintel Beam,Sitting,Lab ,Slab,EX. Room,Chajja,Mumty Room 20 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing complete as per drawing and direction. Gr.Fl,i) Tor steel/Mild Steel,(jsw/jspl/shyam/Srmb/bmasl/electrosteel)ii) In first floor 21 In 1st Floor 22 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straightincluding fitting, fixing and striking out after completion of works (upto roof of ground floor),(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In- Charge.,Tie beam,Lintel beam,Top sink,Blood Collection,Sitting Slab,Chajja 23 In 1st Floor, beam,Lintel beam,Top sink,Lintel for Lab,Sitting Slab,Lintel for Ex.Room,Lab,Sides,Chajja,Mumty Room 24 Brick work with 1st class bricks in cement mortar (1:6),(b) In superstructure, ground floor 25 (b) In superstructure, 1st floor,Piller,Tank Piller,Lab,Less 26 125 mm. thick brick work with 1st class bricks set in cement, sand mortar (1:4) in ground floor. EX. Room,Store.Less for D1,Sink,Sitting Slab 27 In 1st Floor,Less D,Mumty Room,Less,Less for Vst 28 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfer ing corners as directed , Gr.Fl,(i) With 1:4 cement mortar,(b) 10 mm thick plaster, 29 (i) With 1:6 cement mortar,(c) 15 mm thick plaster,Addstore room ,Toilet V3 30 (i) With 1:6 cement mortar,(c) 15 mm thick plaster, Outside 31 In 1st Floor,(i) With 1:4 cement mortar,(b) 10 mm thick plaster, 32 (i) With 1:6 cement mortar,(c) 20 mm thick plaster,EX. Room ,Less D,Store.Less D3 33 (i) With 1:6 cement mortar,(c) 15 mm thick plaster, Lab,Less for W2,Add 1st fl. 125 mm wall 34 Artificial stone in floor, dado, staircase etc with cementconcrete (1:2:4) with stone chips, laid in panels as directedwith topping made with ordinary or white cement (as necessary) ,In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).(ii) 25 mm. thick, In Gr.Fl 35 Supplying and laying true to line and level vitrified tiles ofapproved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, Gr floor(a) One Coat 36 First Floor 37 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.A) Floor,With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thickcement slurry at backside of tiles using cement @ 2.91 Kg/Sq.m&joint filling usingwhitecement slurry 0.20kg/Sq.m.(a) Area of each tile above 0.09 Sq.m,(i) Other thanColoured decorative ,In Gr. Fl,Less D,Less D3Wall,With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles joint filling using white cement slurry @ 0.20kg/Sq.m. Gr.Fl.(b) Area of each tile above 0.09 Sq.m,(ii)Coloured decorative ,Wall of Table top,Wall of Sitting Slab,Less D3,Less V3,In GroundFloor 38 In 1st Floor,WC,LAB,Deduction, D2,D3,v2,Wall of Table top,Wall of Sitting Slab 39 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.A) Floor,With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thickcement slurry at backside of tiles using cement @ 2.91 Kg/Sq.m&joint filling usingwhitecement slurry 0.20kg/Sq.m. Area of each tile upto 0.09 Sq.m,(i) Other thanColoured decorative ,In Gr. Fl,Less D,Less D3Wall,With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles joint filling using white cement slurry @ 0.20kg/Sq.m. Gr.Fl.(b) Area of each tile above 0.09 Sq.m,(ii)Coloured decorative ,Wall of Table top,Wall of Sitting Slab,Less D3,Less V3,In Ground Floora) Wall 40 In 1st Floor 41 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matchingthe stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0kg/Sq.m] 42 Supplying, fitting and fixing 18 mm. to 22 mm. thick kota stone slab in wall, dado in 15 mm thick [avg] cement mortar (1:3) including making suitable arrangement to hold the stoneproperly by brass /copper hooks including pointing in cement mortar (1:2) (1 cement : 2 marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-chargeincluding cost of materials, labour, scaffolding, staging,curing complete.[Using cement slurry for bedding @4.4 kg/Sq.m and for jointing @1.8 kg/Sq.m] 43 Supplying, fitting & fixing granite tiles 10mm to 12mm. thickin columns, wall, facia etc. with 15 thick [avg] cement mortar(1:2) including making suitable arrangements to hold thestones properly by brass / copper hooks including pointing incement mortar (1:2) (1 white cement : 2 marble dust) with,Lab,Sink,Less 44 In 1st.Fl,Lab 45 Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately),(a) Upto area 2.5 Sq.m In Gr.Fl D,D3 46 1st floor 47 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). 48 (h) sal local, In Gr.Fl,(h) sal localIn 1st.Fl 49 Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.iii) 35mm thick shutters with19mm thick panel of size 30 to 45 cm.(b) Sishu, Gamar, Champ, 50 In 1st.Fl,(b) Sishu, Gamar, Champ, 51 Styles and rails of wooden shut ters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor:(i) For 25mm. Thick shutter.(b) Sishu, Gamar, 52 (a) M.S.or W.I. Ornamental grill of approved design joints contin uously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg ./sq .mtr and up to 16 Kg./sq. mtr.In Gr.floor,Plain sheet @ 8 Kg/m2 53 Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately),(b) 40mm X 6mm, 200mm Length 54 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI,(vi) 100mm. X 50mm. X 1.25mm.mark. 55 i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.(a) 200mm long 56 A) Iron door ring of approved quality fitted and fixed with nut and washer complete.(ii) 75mm dia. 57 Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete.(iv) 300mm x 19mm dia. bolt. 58 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:(iii) 100 mm grip x 12 mm dia rod. 59 Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mmx 50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical sectionby galvanised steel screws after inserting two number steel including cost of materials and labour, hire charges of tools and appliances, carriage ofall materials, taxes and ,all other incidental charges complete. 60 Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S.side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm ,shall be tapered on both sides to form lock rail. 61 Supplying, fitting & fixing of partly glazed partly panelled or fully glazed single leaf Aluminium swing door of all aluminium sections viz doorframe ( top and side frame), shutter( top rail, bottom rail, lock rail, door vertical) , glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983 and IS: 1285-1975, annodized conforming to IS:1868-1983, fitted with all other accessories viz. EPDM gusket,cleat, anglescrews etc. including labour charges for fitting and fixing of aluminiumdoor with door spring,/aluminium hinges, glass / Panel board allcomplete as per architectural drawings and direction of Engineer-incharge.( Excluding cost of glass/ panel board, door spring/ Al hinges, door closer, door stoper, handle, tower bolt and locking arrangment etc)10-12 Micron thickness Annodizing film Natural white. 62 Providing, fitting and fixing in position, medium density fibre board conforming to IS: 12406-1988 for plain and IS: 14587-1998 for prelaminated made of wood fibre bonded with Urea formaldehyde for interior grade and Phenol Formaldehyde for exterior grade conforming to per IS:848-1974 as per approved make and brand as per direction of Engineer-in-Charge.(C) Both side decorative lamination, (II) Interior Grade. 12mm 63 Supplying 4 lever mortice lock of any approved make and brand as per direction of the Engineer-in-Charge. 64 Anodized aluminum barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (vii) 225mm long x 10mm dia. Bolt 65 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aconforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket,10-12 Micron thickness Annodizing filmNatural white,For 2-Track window :Gr. Fl.W,Stair ,1st. Fl.W,Lab ,. Fl.Stair, V 66 (a) M.S.or W.I. Ornamental grill of approved design joints contin uously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg ./sq .mtr and up to 16 Kg./sq. mtr.In Gr.floor,Plain sheet @ 8 Kg/m2 67 In 1st floor 68 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.i) 4mm thick clear glass. 69 Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than150mm apart complete in all respect as per design including cost of all labour and materials.In First.Fl 70 Square or hexagonal mesh netting made with 18 B.W.G. galvanised wire, fitted and fixed complete as per design (excluding the supporting framework but including local sal wood battens of size 37.5mmx25mm).In ground floor.. 71 (b) 25mm mesh, In 1st Fl 72 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor) (One coat) 73 Applying Acrylic Emulsion Paint of approved make and brand on wallsand ceiling including sand papering in intermediate coats including putty(to be done under specific instruction of Superintending Engineer) :(Two coats) 74 (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.On Timber surface, Gr.Fl +1st,D 75 (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.win grill,Collap,Grill,Stair Stair Gate, 76 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :iv) Two coats (with any shade except white)On Plastered surface, Gr.Fl +1stOn Timber surface, Gr.Fl +1st 77 Other metal Surface, Windows, Grills Etc. 78 Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge),In Gr. Fl,Deduction, 79 1st floor 80 Applying Exterior grade Acrylic primer of approved quality andbrand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish),a) One Coats, Gr. Fl 81 1st floor 82 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat),a) Normal Acrylic Emulsion 83 In 1stfloor (Two Coat) 84 Labour for Chipping of concrete surface before taking up Plaster ing work.1ST Fl. 85 (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with waterin proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturers specification,1ST Fl. 86 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in 87 1.5 mm thick Net cement finish in wall, dado, 88 Main signageof Vinyle Board with ACP Boarder 1800X1200 MM 89 Easing and oiling, cleaning collapsible gate and repairing tolocking arrangements. 90 Reparing collapsible gate by cutting out all rivets as necessary reassambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coa 91 Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in anysoil through masonry concretestructures etc if necessary and mending good damages including joining with jointingmaterails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. (ii)110 mm. Dia. 92 c) Bend 87.5 degree. (ii)110 mm. Dia. 93 d) Shoe (ii)110 mm. Dia. 94 Sanitary PlumbingSupplying, fitting and fixing PVC pipes of approved make of Schedule 80(medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew,reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc.complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately. (b) For Exposed Work.PVC Pipes PVC Pipes.40 mm 95 25 mm 96 (b) For Concealed Work. PVC Pipes.20 mm 97 (b) For Concealed Work. PVC Pipes.15 mm 98 Supplying, fitting and fixing bib cock or stop cock. (a)i) chromium platedbib cock short body (equivalent to code no. 511 & model- tropical./ sumthing special of ESSCO or similar brand) 99 (d)i) chromium plated angular stop cock with wall flange (equivalent to code no. 5053 & model- Florentine of Jaquar or similar brand) 100 Supplying P.V.C water storage tank of approved quality with closed top with lid(black)-Multilayer. (c) 500 litre capacity 101 Supplying fitting & fixing 10 ltr. PVC low down cistern conforming to I.S specification with PVC fittings complete C.I brackets including two coats of painting to bracket etc. 102 Labour for punching hole in plastic water storage tank up to 50 mm dia. 103 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(ii) 550 mm X 400 mm size 104 (iv) Angle back wash basin 400 mm X 400 mm 105 Supplying, fitting and fixing White Vitreous China Sink in position on C.I. brackets including two coats of painting of brackets.(i) 610 mm X 450 mm X 200 mm(a) Plain edge sink with overflow 106 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P.nut,15 mm dia. i) 450mm long 107 Suppling fitting & fixingapproved brand 32mm dia p.v.c waste pipe with p.v.c coupling at one end fitted with necessary clamps.i)900mm long 108 Suppling fitting & fixing15 mm swan neck tap with left & right hand operating knob with aerator. 109 Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.530 mm X 430 mm x 180 mm 110 Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding P or S trap (excluding cost of concrete for fixing).(i) 580 mm X 440 mm 111 Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges.(i) 450 mm X 300 mm 112 Supply of UPVC pipes (B type )& fitting conforming to IS 13592-1992 .A) i) single socketed 3 mtr length --b)110 mm 113 (ii) Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials. A) Above ground .(ii) 110 mm dia. 114 A) Under ground.(ii) 110 mm dia. 115 B) FITTINGS.Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992.viii) Double Y with Door.b) 110 mm 116 xi) door bend ( T.S.) b) 110 mm 117 xv) vent cowl-(b) 110mm 118 xvi) pipe clip ---(b) 110 mm 119 (ii) Plain Tee---(b) 110 mm 120 Suppling fitting & fixing E.W.C in white glazed vitreous china ware of approved make supplied fittied complete in position with necessary bolts nuts.etc. a)with P trap 121 Supplying fitting & fixing squating plate with integral flushing in white vitreous chinaware of approvedmake in cement concrete (6:3:1) with jhama chips complete. i)450mm X350mm 122 Supplying fitting & fixing closet seat of approved make with lid & C.P hinges,rubber beffer & brush screw complete. (a) E.W.C. (ii) Plastic (hallow type) white 123 Supplying fitting & fixing 32 mm. dia. flush pipe of approved make with necessary fixing materials & clam complete. i)Polythene flush pipe. 124 (i) Supplying, fitting and fixing liquid soap container.c) (a) Cromium plated. 125 Supplying fitting & fixing towel rail with two brackets.a)C.P over brush---i)25mm dia,450 mm long. 126 Submersible WorksSupplying and delivery at site Submersible Pump Set incl. S&F 1.5 H.P Control Panel (Model: SPC2)3 core 1.5 Sq.mm flat copper cable (3M length) having following specification:-No of stage -25,Head-110 mtr,Discharge-1.8m3/hr ,nrv-32 mm Make: CROMPTON GREAVES / Similar make. Model:, 1.5H.P with Control Panel, Size of Tube well : 4 x 2. 127 Finishing the end of following P.V.C armoured Cable by crimping method incl.supplying and fixing solderless socket (Dowels make), tapes , anticorrosive paste & jointing materials. a) 3 Core 4 sq.mm PVC/A cable 128 Supplying and laying 1.1kv grade PVC/A cable as below including S&F of earth continuty as below after cutting floor/pavement/wall/and making holes incl. Embedding the cable at an average depth 75mm in floor/wall/ pavement etc. and mending good the damage to original finish incl. removing the rubbish. a) 2 Core 4 sq.mm PVC/A cable with 1x8 No.SWG G.I 129 Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of PVC armoured cable as below: a) 2 Core 4 sq.mm PVC/A cable 130 Finishing the end of following P.V.C armoured Cable by crimping method incl.supplying and fixing solderless socket (Dowels make) , tapes , anticorrosive paste & jointing materials. d) 2 Core 4 sq.mm PVC/A cable 131 Supplying and fixing C.I water proof looping cable box having hinged top cover having 4mm thick with rubber gasket living railway type mechanical locking arrangement earthing terminal with lug etc of size 8x6x4 comprising 3 Nos 15amps Kit-Kat fuse unit and housing the same in pole muffing 132 Supplying and laying 1.1kv grade PVC/A cable as below including S&F of earth continuty as below after cutting floor/pavement/wall/and making holes incl. Embedding the cable at an average depth 75mm in floor/wall/ pavement etc. and mending good the damage to original finish incl. removing the rubbish. a) 2 Core 4 sq.mm PVC/A cable with 1x8 No.SWG G.I 133 Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore. (c) For depth upto 150 metre for 50 mm dia. Tube well with top enlargement of 100 mm dia. (i) 50 mm dia. boring etc. 134 (ii) 100 mm dia. boring etc. top enlargement 135 Supplying, fitting and fixing plug of approved make conforming to I.S. specifications. (i) 50 mm 136 Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets. (i) 50 mm dia. 137 Supply of G. I. pipes of TATA make including necessary sockets ,(e) 50 mm dia. (ii) Medium quality 138 Supplying PVC strainer of approved make with adapter conforming to I.S.12818 specifications. (i) 50 mm dia. 139 Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). i) 32 mm 140 ii) 40 mm 141 i) 50 mm 142 ii) 100 mm 143 Labour for fitting and fixing high density poly-ethylene pipes or P.V.C. pipes for above ground work including cost of jointing materials paints etc. fitting and fixing all necessary specials, cutting pipes, making threads, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, (iii) 32 mm dia. 144 (v) 50 mm dia. 145 (viii) 100 mm dia. 146 Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). vii)25mm Dia 147 Supplying, fitting and fixing heavy type bell mouth reducing socket. (i) 50 mm X 100 mm 148 Supply of galvanised iron socket with I.S.I. mark. (iv) 50 mm 149 Supply of G.I. bend. (iv) 50 mm 150 Supply of G.I. plain equal elbow of approved brand and make. (iv) 50 mm 151 Supply of G.I. nipple standard 50 mm long. (iv) 50 mm 152 Supply of G.I. union. (iv) 50 mm 153 Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (iv) 40 mm 154 Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with V notch including hire and labour charges for all tools and plants, and scaffolding as required. 155 Labour for making arrange ment for showing verticality test including the cost for hire charges of tools and plants, scafolding, labour etc.all complete. 156 Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equip ments, paying all charges and fees, testing etc. complete in all respect , as per direction. 157 Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary includingsupply of necessary report. 158 Waiting ShadeM.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. Payment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof. i) For roof truss works a) Span up to 12 Mtr.Horizontal Bar(50x50x3)-@4.39Kg/M. Vertical Bar(50x50x3)--@4.39Kg/M 159 Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make(excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work).(i) In Roof:- a) With 0.50 mm thick sheet. 160 Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. includingnecessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Usingcement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.mfor joint filling], Ground Floor 161 Page -15 / Item-08Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth 162 Electrical Works Supplying and fixing 250 V, 6-10A per way, (2+8 way)SPN MCBDB with SS enclosure double-door with IP-42/43 protection with DP Isolators as incomer and SPMCBs (C Curve, 10kA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment, 1no 40A DP MCB type Isolator, 10 no. 6-16A SPMCB) (Make- Schneider/ Legrand/ Siemens (8GB32102RC08)) 163 Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) in suitable size PVC casing-capping (Precision make) with 1x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire for ECC, incl. necy. PVC clips, fittings etc. to light/fan/call bell point with piano key type switch (Anchor make) fixed on sheet steel fabricated switch board with Perspex/bakelite top cover on wall incl. necy. connections and making earthing attachment and mending good damages to building works. [PVC casing-capping and Switch board both on surfacea) Average run 5 mtr 164 Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit FR(Precision make), with 1x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall complete with 2 no. suitable size “Ph & N” copper bar incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. 175mmx100mmx65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finisha) Average run 5 mtr 165 Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required 166 Supply & Fixing 240 V, 6A, plug socket with separate 6 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws aftermaking housing for switch by cutting bakelite/perspex cover and making necessary connections as required 167 Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch, indicator & 20A switch type SP MCB (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required 168 Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MSflat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991) 169 Supply & FixingSocket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switch board with bakelite/ perspex top cover by screw incl. making necy. connections etc. 170 Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. ( C-3, Item No- 21,a ) 171 Supply & delivery of Sweep:- 48 (1200mm) AC ceiling fan, 50-70 Watts, Speed:->=350 RPM, Air delivery:->=220 CMM, make: (Orient PSPO NEWBREEZE or SUMMERCOOL / equivalent of EPC or USHA STRIKER PLUS or CROMPTON [Approved by EIC]a) 1200 mm sweep 172 Supply & delivery of single 4ft LED tube light fitting incl. 4ft LED tube,1200 mm, Efficacy>= 100 lm/W, THD<10%, complete with all accessories. (Mas LEDtube 1200mm) [Philips: TMC 501 P 1xT-LED 22W P3241] or equivalent of Havells, Crompton etc. [Approved by EIC] 173 Fixing only single /twin fluorescent light fitting complete with all accessories directly on wall/ceiling/HW round block and suitable size of MS fastener.( C-2, Item No- 14,b ) 174 Supply9W LED lamp to the lamp point. [PHILIPS make][NS] 175 Fixing only lamp[11/C-2] 176 Distribution wiring in 1.1 KV single core stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit FR (Precision make) incl. necy. fittings as required2 x 84/0.3 (6 sqmm) + 1 x 56/0.3 (4 sqmm) ECC [1(iv). / E-14] 177 2 x 56/0.3 (4 sqmm) + 1 x 36/0.3 (2.5 sqmm) ECC[1(iii). / E-14] 178 2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC[1(ii). / E-14] 179 2 x 36/0.3 (1.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC[1(i). / E-14] 180 Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes.2x56/0.3 (6 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC [9(iii)/F-5] 181 2x56/0.3 (4 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC [9(ii)/F-5] 182 2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC [9(i)/F-5] 183 Supplying and fixing Sheet steel Main Switches on flat iron frame on wall DP 32 A (Page No. D1 item No.1(a)) Make - HPL/Havells 184 Supplying & fixing sheet metal (16 SWG) Iron Clad Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required – ( As per Drawing no. 470 of PWD Specification Book – May 1991)DP 32 A (Page No. D1 item No.1(a)) Make - HPL/Havells 185 Supplying and fixing Changeover switch with Sheet Steel enclosure on flat iron frame on wall with nuts bolts etc240V DP, 32A (Page No. D 1, item No. 2 (a)) Make - HPL/Havells 186 Supplying and fixing MCB SS enclosure with IP-20/30 protection, powder coated provision for two/four pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment. 2 Way DB (Page No. D 9 item No.11) 187 Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection 188 32 A DP MCB [Make - Legrand / Schneider] (Page No. D 6 item No.7) [UPS Incomer DB:1 & Outgoing DB:1] (in case of installation of UPS at First landing of staircase of 1st Floor: Incomer DB:2) 189 25 A DP MCB [Make - Legrand / Schneider] (Page No. D 6 item No.7) [Emergency DB Incomer] 190 2+4 Way enclosure (607710) [Make - Legrand / Schneider] (Page No. D 9 item No.13) [UPS DB] 191 Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled withbitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By TATA-Medium GI pipe (Page No.G-1/2(a)) [For UPS] 192 Excavation of soil for installation of Earth Electrode and filling & ramming.For Morrum Soil (Page No.G-1/1(b)) 193 Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required (Page No.G-2/4(a)) 194 Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. 195 Connecting the equipments to earth busbar including S & F GI(Hot Dip) wire of size as below on wall/floor with staples buriedinside wall/floor as required and making connection toequipments with bolts, nuts, washers, cable lugs etc. asrequired and mending good damages (a). Solid GI wire : No. 10 SWG (Page No.G-2/5(a) (iv)) 196 Extra for providing masonery enclosure on the top of the earthelectrode of overall size 86.36 cm x 86.36 cm x 46 cm deep(below Ground level) complete with cemented brick work(1:6)of 25 cm width duly plastered with cement morter (inside) CIhinged inspection cover of size 36.56 cm x 35.56 cm withlocking arrangement, GI reducer including drilling of 46 nos.12 mm dia holes on the GI pipe (Page No.G-2/3(a)) 197 Add :- G.S.T @ 18% 198 Add : Labour Welfare Cess @ 1%