Tender For Construction Of Shc Building At Mehliya P.S Bhadra Distt. Hanumangarh (15Th Fc) S No. 01 - Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 4 Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 5 CARRIAGE OF MATERIALS Earth, Sand, Lime, Morrum manure or sludge For 5 Km. 6 Brick masonary in foundation and plinth with bricks of class designation 75 mm in :Cement Mortar 1:6 (1-Cement:6-coarse sand).Cement mortar 1 : 6 (1 cement : 6 coarse sand) 7 Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 8 Providing and laying in position specified grade ofcement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix 9 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 11 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Cold twisted deformed bars (IS : 1786). 12 Brick work with common burnt clay F.P.S.(Non Modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in :Cement mortar 1 : 6(1 cement : 6 coarse sand) 13 Half brick masonry with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.5 in Superstructure , above plinth level upto floor fivelevel.Cement mortar 1 : 4 (1 cement : 4 coarse sand) 14 Add extra providingand placing in position 2 Nos. ,6mm Ø M.S. barat every thirdcourse of half brick masonry . 15 Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge :Profile B 16 Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge Window openable. 17 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 18 Providing and fixing Square bars or other flat welded to window, ventilatiors etc. 19 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure A: 20 Commercial Veneer both side 21 Decorative teak veneer both side 22 Providing and fixingaluminum workfor doors, windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285,fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc., all complete as per architectural drawings and thedirections of Engineer- in – charge. (Glazing and paneling to be paid for separately). 23 For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). 24 Polyester Powder coating aluminum( minimum thickness of powder coating 50 micron) 25 Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 26 Grade 304 27 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basicitem.) 28 With float glass panes of 8 mm thickness 29 Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. 30 Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. 31 Prelaminated particle board with decorative lamination on both sides. 32 Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). 33 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete 34 For area of each slab from 2001to 5000 Sqcm 35 P & F 1st quality Heavy Duty Vitrified Double Charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. 36 size600 mm X 600mm 37 Plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 38 20mm thick . 39 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 40 New Plastered Surface (three or more coats) 41 Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 42 New Work 43 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: 44 Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 45 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 46 Two or more coats on new work 47 Grading roof for water proofing treatment withwater proffing compound 48 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 49 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 50 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 51 Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1:2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1:3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. 52 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 53 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. 54 Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) 55 Making grooves as per design in plaster 10mm to 20mm wide. 56 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles includingrubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) 57 Medium shade using approximately 50% white cement and 50% ordinary cement. 58 Add extra for non slipping 9-12 mm ironite topping tiles 59 Part B Sanitary work 60 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: 61 Size 580x440mm. 62 P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor 63 P & F water closet Seat Covers with brass hinges complete :Solid PVC (ISI marked) grade-I White for EWC. 64 P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. 65 P & F G.I. Pipeswith G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-(Internal work) Medium Duty Pipes Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall.15mm dia nominal boreB Class 66 P & F G.I. Pipeswith G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-(Internal work) Medium Duty Pipes Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall.25mm dia nominal boreB Class 67 P & F G.I. Pipeswith G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. :-(External Work) Medium Duty Pipes 15mm dia nominal bore B Class 68 P & F G.I. Pipeswith G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. :-(External Work) Medium Duty Pipes25mm dia nominal boreB Class 69 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Long body, 15mm nominal bore weight not less than 690 gm 70 P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete :Brass wt.400 gm,15mm. 71 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. 72 -do- with 60 Cm. long thread and nut. 73 P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : 74 Gun-metal 15mm nominal bore. 75 P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :25mm nominal bore. 76 P & F Sink Cocks of superior quality & approved made : 77 (-do-) Casted Spout 15 mm. 78 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make,PVC waste pipe with PVC nut 32mm complete including cutting & making good the wall : 79 Size 610mm x 510mm 80 P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including placing on terrace (at all floors), making connection etc. complete of approved design. 81 1000 Litre capacity 82 P & F 1st quality WVC pedestal for wash basin. 83 Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size : 84 15mm dia nominal bore 85 Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size : 86 25mm dia nominal bore 87 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 88 110 mm dia 89 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 90 110 mm dia 91 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 92 Bend 87 .5 93 110mm dia 94 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 95 Gully Trap 110 mm 96 Single Tee with Door 97 75mm 98 110mm 99 Nahni Trap100mm with CP Jali 100 W.C. Connector (Bend) with ring 101 110mm 102 Bend 87.5 Dg. 103 75mm 104 110mm 105 Vent Cowel 106 75mm 107 110mm 108 Construction of soakage well in all type of soil with 345 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring, earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: 109 Size 300 Cm. dia outside & 300 Cm. depth . 110 Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering,jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth worketc . complete including disposal of surplus earth within a lead of 50 mtr . 111 Inner dia90 Cm & 10 to 12 Mtr deep. 112 Construction of chamber in all type of soil with 230 mm thick brick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 40mm thick M-15 grade C.C. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 113 Inside size 300 X 300 mm depth upto 0.5 M,Cement concrete cover with frame. 114 -do- size 450 x 450mm depth upto0.5 M,Cement concrete cover with frame. 115 Construction of manhole in all type of soil inner size 90 X 60 Cm. 230 mm thick brick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. 116 Depth up to 0.5 M 117 P & F kitchen & Lab Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up to floor level complete including cutting and making good the wall & floor : 118 White vitreous china laboratry sink: 530x430x180 mm 119 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: 120 PVC withPVCbend and superior internal fittings 121 P & F Towel Rail or Ring of approved quality/make: 122 C.P. brass Towel Rail elbow type with concealed screws size 450mm (Heavy duty).
