|
| 1 | Work |
| 2 | Earth work in exacavation in foundations in ordinary soil (loam clay or sand) including lift upto 1.5 m and lead upto 30 mt. & including filling, watering and ramming of excavated earth into the trenches or into the space between building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the E/I upto a distance of 30 mt. from the foundation trenches. (PWD-251) FT1,LAB PLATE FORM,Step |
| 3 | Filling of carted earth. AR-IDeduct Qty Same as item no. 1*30/100 UNDER FLOOR- PHYSICS-chemistry,biology LAB, TEACHER ROOM, STORE |
| 4 | Concrete with 40mm gauge Brick ballast, sand of 1.25 fineness modulous in 8:4:1 in foundation including supply of all materials labour and tools and plants etc. required for proper completion of work. S.I. No. 275 |
| 5 | Providing & injecting chemical emulsion for pre constructional antitermite treatment and creating a chemical barrier under and around the column pits wall trenches basement excavation top surface ifplinth junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc., complete (plinth area of the building at ground floor only shall be measured as per IS-6313 Part II 1981)Aldrine emulisifiable concentrate or any other approved material such as Hepthachlor or Chlordance will be used. The rate of application of chemical emulsion shall be as follows- (I) Treatment for masonary & foundation 5 Ltr. per Sqm. (II) Back fill in immediate contact with foundation 7.5 Ltr.per Sqm. (III) Treatment of top surface of plinth filling 5 Ltr.perSqm. (IV) Treatment ofsoil along external peri meter of building 7.50 Ltr. per Sqm. (V) Treatment of soil under apron along external perimeter 5 Ltr. per Sqm. Chapter 8 |
| 6 | R.C.C.Work with cement approved coarse sand and 2cm gauge stone girt (Dala) in the propotion of 1:1.5:3 (M-20) in Column Footing excluding supply of reinforcement and its bending but including fixing and bending the same with 24 B.W.G.G.I. banding wire and including necessary centering and shuttring etc.& also including supply of all materilas,labour and T&P etc. required for proper completion of work.As per S.I.No.287Footing |
| 7 | R.C.C.Work with cement approved coarse sand and 2cm gauge stone girt (Dala) in the propotion of 1:1.5:3 (M-20) in Ligher Beam excluding supply of reinforcement and its bending but including fixing and bending the same with 24 B.W.G.G.I. banding wire and including necessary centering and shuttring etc.& also including supply of all materilas,labour and T&P etc. required for proper completion of work.As per S.I.No. 285B1 |
| 8 | R.C.C. work withcement, approved coarse sand and 20 mm gauge stone aggrigate with M-20 nominal mix 1:1.5:3 in plinth & lintel Band & excluding the supply of reinforcement and its bending but including its fixing and binding with 24 BWGGI binding wire, centering and shuttering, supply of all materials, labour and tools and plants etc. required for proper completion of work. As per S.I.No. 283PIINTH BAND,LINTEL BAND |
| 9 | R.C.C. Work with cement approved coarse sand and 20 mm gauge (nomianl size) dalla stone aggregate in the proporation of1:1.5:3M-20 in R.C.C. Column excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B W.G.G.I. binding wire and as required supply of all materials, labour centering and shuttering and removal of the same after completion of work. S.I.No. 289 UPTO PLINTH, ABOVE PLINTH, C1 |
| 10 | R.C.C. work with cement, approved coarse sand and 2 cm gauge approved stone ballast in the proportion 1:1.5:3in R.C.C. Slab, excluding supply of steel and its bending but including fixing and binding the same with 24 B. W.G.G.I binding wire and including necessary centering and shuttering etc and also including s/o all materials required for proper comletion of the work. As per S.I. No. 284Slab,CHAJJA,PLATE FORM |
| 11 | Mild steel or iron work in plain work such as reinforced cement concrete (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of work, supply of steel, all labour etc. required and including wastage bend, hooks and authorised over lapping shall be measured. As per s.i.no. 504 |
| 12 | First class brick work in 1:6 cement and Finesand of 1.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour, T & P etc reqiored for proper completion of the work. PWD-303 |
| 13 | First class brick work in 1:6 cement and Fine sand of in super-structure above plinth level up to floor two level ( up to two storeys ) includingnecessarycutting and moulding of brick work asrequiredand also including honey combed brick work PWD- 303+309+310 |
| 14 | 12 mm cement plaster in single coat on plane side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6fine sandPWD- 586Interior Face |
| 15 | 12 mm cement plaster in single coat on plane side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6fine sandPWD- 586EXTERIOR FACE |
| 16 | Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (25 mm thick floor). PWD-601A |
| 17 | Fabrication supply and fixing of M.S.Angle iron (40x40x5mm) in chaukhats for door, windows and ventilatorsincluding using m.s.flat iron etc. and 3 mm thick gusset plates at corners and junctions including supply of steel cutting, drilling holes bending, moulding requried shap and welding, supply and fixing of necessary hings for doors 125mm of 14 gauge size, window and ventilator 100mm, 16mm gauge size, with cleats and stoppers etc. and 10 mm dia bottom tie rod etc. complete. S.I.No 502 |
| 18 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35mm thick Single leaf S.I.No. 470(ii) |
| 19 | Z-sction windows (ISI marke) or Z- tubler window made of gold rolled formed continous seam welded M.S. tubler box section made from corrosion resistant coated conforming to IS: 513=1973 size of welded tubuler Z-profile and T profile are glzing bars jointed mitred and flush but welded and lugs 100 mm long of 19 x 3 mm size embedded in cement concrete blocks 150 x 100 x 100 of 1:3:6 cement approved coarse sand and 20 mm nominal size of dalla stone aggregate or with plugs and screws required including fixing 4 mm thick glass panes with glazing and special metal sash putty of approved make complete including M.S. oxidised casement fastercer (125 mm length weighting not less than 240 gms) and box type hinges 65 mm length 2.5 mm thick galvnised pinof 6 mm dia and aplying a priming coat of approved steel primer. S.I. No. 502 |
| 20 | Fabrication and supply ofM.S. grillas per approved design and drawing including the stair case railling etc. with square bars, m.s. angle iron, and m.s. flat iron as per direction of Engineer-incharge, supply of steel and its wastage, cutting, drilling holes and welding joints where necessary including each joint tube perfectaly welded and jointed and grinded to smooth finish. S.I.No 502 |
| 21 | Fixing panes of glass with and including putty and brads and including supply of all material labour and tools plants etc. required for proper completion of the work, but excluding cost of glass. M.R. |
| 22 | Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (PWD 649+650)Ceiling |
| 23 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm): SOR New Item 13.47.1OUTER |
| 24 | Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. PWD13.80QTY SAME AS (ITEM NO. 25+26) |
| 25 | Painting or Varnishing(PWD - 641+642 Door Chaukhat |
| 26 | Painting or Varnishing(PWD - 641+642 |
| 27 | Internal Electrification |
| 28 | Wiring points for light with 1.5 sqmm.FR PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sqmm.FR PVC insulated multistrand copper conductor cable as earth continuity wire and piano type switch etc. complete in all respects. Earth continuity wire and modular type switch etc. complete in all respects. |
| 29 | Wiring point for 5 amp Plug with 141( B) but in PVC conduit with 1.5 sq. mm FR PVC insulated multisrand copper conductor cableas earth wire drawn inside the conduit. |
| 30 | As in item 221 (B) but in 20 mm dia (2mmthick) PVC conduit with one no. 2.5 sq. mm for PVC insulated multisrand copper conductor cable as earth wire drawn inside the conduit. |
| 31 | Supply and wiring submains with two number 10.0 sq mm. FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) PVC conduct with one no. of 6.0 sqmm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit complete. |
| 32 | Supply & fixing of 40 Amp. 4 pole MCB (10KA) |
| 33 | Erection and testing of ceiling fan and regulator etc. excluding supply of down rod, complete in all respects. |
| 34 | Supply and fixing of power plug with 15A/250 V flush type socket in suitable M.S. box of 175 mm. x 100 mm. x 50 mm. size with bakelite sheet cover 3 mm. thick fixed with brass machine screws and cup washer. Thick fixed with brass machine screws and cup washer. |
| 35 | Supply and writing of submain with 2 Nos. 1.5 Sq.mm. FR PVC insulated 1100 V grade multi strand single core conductor cable in 20 mm. dial heavy duty (2 mm. thick) PVC conduit with 1 No. 1.5 Sq. mm. FR PVC insulated 1100 V grade multi strand single core copper conductor cable as earth wire drawn inside the conduit complete in all respect for computer points. |
| 36 | Supply and fixing of LED fitting suitable for 1x22 watt LED tube light complete including tubes etc. on surface complete in all respect crompton, bajaj, phillips make. Cat\"\" AAA |
| 37 | Supply and fixing of electronic fan regulator (Modular) 120-280 V. ISI maked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of engineer in charge of work. |
| 38 | S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work. |
| 39 | Supply of Ceiling Fan with motor of A.C. Permanent insulation capacitor rating confirming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated volage 220/240 volts, 50 Hz, 1-ph A.C.the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. BEE 5 Star rated-1200mm sweep |
