Renovation Of Guwahati Guest House. Civil Works.; 1 CIVIL WORKS 2 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. 3 Reinforcement cement conrete work in walls (any thikness), including attached pilasters, buttresses, plinth and string courses, fillest, Columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1.:1.5.:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 4 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 5 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) 6 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) 7 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 8 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer 9 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work. 10 Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 11 Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 12 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). 13 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size, Size of Tile 600x600 mm 14 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Size of Tile 600x600 mm 15 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 16 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 17 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood 18 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood 35 mm thick shutters 19 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer in-charge.Extruded section profile size 42x50 mm 20 Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of H section, a uPVC hollow section of size100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats.The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 21 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc. 22 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately)For fixed portion, Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 23 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium (anodised transparentor dyed to required shade according toIS: 1868, Minimum anodic coating of gradeAC 15) 24 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 25 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, herry/Ruby red, Area of slab upto 0.50 sqm 26 Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete 27 Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 75x65x4 mm (heavy type) 28 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia 29 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm 30 Providing , fitting & fixing of Godrej Cylindrical Lock suitable for Doors. 31 Providing fitting and fixing of Curtain Bracket SN152 32 PLUMBING AND SANITARY WORKS 33 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid 34 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White 35 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 36 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm 37 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 38 Providing and fixing toilet paper holder : C.P Brass 39 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. 40 Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. Including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &b fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 50 mm dia. 41 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVCPlain brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia. Pipes. 42 Providing and fixing brass bib cock of approved quality : 43 15 mm nominal bore 44 20 mm nominal bore 45 Providing and fixing brass stop cock of approved quality : 46 15 mm nominal bore 47 20 mm nominal bore 48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 49 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 50 Providing fitting and fixing C.P Bib cock COP-CHR-037PM 51 Providing fitting and fixing C.P Towel ring Diamond-741820 52 Providing fitting and fixing C.P soap Dish Diamond D503 53 Providing fitting and fixing C.P Shower arm SHA-CHR-477 54 Providing fitting and fixing Concealed Cistern with control plate Jaquar make JCS-WHT-2400FS-SPS with JCP-CHR-325415-CONTROL PLATE 55 Providing andfixing wall hanging Commode Jaquar make etc. complete APS WHT 39953BIUFSM 56 Providing fitting and fixing overhead shower of 150x150 mm OHS-CHR-1605 57 Providing fitting and fixing C.P Twin Bib cock Jaquar make FUS-CHR-29041 58 Providing fitting and fixing C.P Angle Stop cock Jaquar make FUS-CHR-29053 59 Providing fitting and fixing Hand wash Bottle Dispenser with Stand Jaquar make CAN-CHR-1135N 60 Supplying, fitting & fixing CP concealed health faucet shower Agmeco make with 1.2 metre flexible tube &ABS wall bracket etc. complete Jaquar make 61 Overhauling of iron removal filter including uploading of media from the vessel , cleaning of vessel , supplying of new iron rempoval filter media sets. Supply of 1 & 1/2 multipot valve, new alum dozer PVC strainer set, pressure gauze, 1 & 1/2 operating line and air vaccuam etc complete. 62 REPAIRING AND PAINTING WORKS 63 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work 64 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :(Steel Surface). One or more coats on old work 65 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :(Wooden Surface). One or more coats on old work 66 French spirit polishing : One or more coats on old work 67 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 68 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) 69 Renewing glass panes and refixing existing wooden fillets: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) 70 Refixing old glass panes with putty and nails. 71 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 72 50 mm nominal dia Pipes 73 25 mm nominal dia Pipes 74 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessaryscrews etc. complete. 75 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore 76 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm nominal dia Pipes 77 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessaryscrews etc. complete 78 ELECTRICAL WORKS 79 Wiring for light/fan/exhaust fan/call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recess PVCconduit with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq. mm FRLS PVC copper cable as required. Group A 80 Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recess as required. 81 2x2.5 sq. mm+ 1X2.5 sq. mm earth wire 82 2X4 sq. mm+ 1X4 sq. mm Earth wire 83 4X10Sq.mm + 2X6Sq.mm earth wire 84 Supply and fixing following size/modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required. 85 4 module 86 6 module 87 8 module 88 Supply and fixing modular blanking plate on the existing modular plate and box excluding modular plate as required. 89 Supply and fixing 2 module step type electronic fan regulator on the existing modular plate switch box including connection but excluding plate 90 Supplying and fixing modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate as required. 91 15/16 A switch 92 6 pin 15/16 A socket outlet 93 3 pin 5/6 A socket outlet 94 5/6A Switch 95 Supply, installation,testing and commissioning of 1200 mm sweep, BEE 5 Star rated Ceiling fan with Brushless direct current motor. Class of insulation B, 3 no.s of blade, 30 cm long down rod, 2 no.s canopy, shackled kit, safety rope, copper winding, power factor not less than 0.9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/min, 350 rpm (tolerence as per IS: 374-2019). thd less than 10% with electronic regulator for speed control and all remaining accesssories including safety pin, nuts and bolts, washers, temperature rise =75º C(max) insulation resistence more than 2 MΩ, suitable for 230V, 50Hz, 1-φ AC supply, earthing etc. complete as required. 96 Supply Fitting & Fixing of industrial type 300mm sweep exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 97 supply, installation,testing and commissioning of 20 W LED Tube Fixtures including connections etc. complete as directed 98 Supply fitting and fixing of 10W LED bed side light complete with LED lamp and conections etc. 99 Supply fitting and fixing of 10W LED wall light set complete with LED lamp and conections etc. 100 Supplying and fixing following way surface/recess mounting vertical type three pole and neutral,sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4+24), Double door 101 Providing and fixing following rating and breaking capacity and pole MCCB with thermo magnetic release and tertminal spreaders in existing cubicle panel board/DB including drilling holes in wall, making connections etc. as required complete. 125A, 36KA, four pole MCCB 102 Supplying and fixing 5A to 32 A rating,240/415 V, 10 KA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and comissioning etc as required. Single Pole 103 Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm 104 Supply of 4 core 35 sq. mm armoured aluminium cable. 105 Supply, fitting and fixing retrofit LED bulb 106 supply, installation,testing and commissioning of 12 W LED recessed Round panel light fixtures including connections etc. complete as directed 107 Supply, fitting and fixing of required sizes of fan hook by fitting fastening nuts and bolts etc. complete as directed. 108 Supply, fitting and fixing of modular Air-Conditioner starter with board and connections etc. as required complete 109 Providing and fixing 4mm diacopper wire on surface or in recess for loop earthing as rquired.
