Tender For Konch Nagar Palika Parishad Water Supply Scheme Under Amrut 2.0 Distt. Jalaun - Construction Of R.C.C Over Head Tank (Oht)Supply Of All The Materials, Labour T&P And Construction Of A R.C.C. Over Head Tank Above Ground Level With Main Component, konch-Uttar Pradesh

Tender For Konch Nagar Palika Parishad water Supply scheme Under Amrut 2.0 Distt. Jalaun - Construction of R.C.C Over Head Tank (OHT)Supply of all the materials, labour T&P and construction of a R.C.C. Over head tank above ground level with main components, based on IS-3370 or liquid storage concrete in over head tank and foundation concrete as per specification in I.S. 2911.Following capacity/StagingAll Components of OHT will be casted in M-30 concrete with cement, coarse sand and approved stone grit as per I.S. 11682 and I.S. 456.Minimum depth of foundatation below original ground level will be 2.50 M.Seismic effects and wind load should be taken into consideration as I.S. 1893for earthquake resistance and I.S. 875 part-III for wind load on structure. The asumed bearing capacity of soil has been taken as 8 M.T. sqm.1m wide RCC dog legged stair case from ground lavel to balcony.M.S. ladder made of 50 X 50 X 6 mm angle section and 20 mm plain M.S. bars (specification of M.S. should be as per IS 800-2007) with hand rails of 20 mm medium class G.I. pipes on both sides in three rows from balcony to top dome resting on an RCC plateform (75 X 75 cm and 10 cm thick) projecting from top ring beam and one alluminium ladder inside the tank body (from manhole to tope dometo bootom dome).1 m wide R.C.C. balcony around the tank at the junction point of vertical wall and conical wall.Proper R.C.C. railing and 20 mm dia medium class G.I. pipe (in 3 rows) on both sides of stair case, arround the balcony at each landing from landing with top ring beam upto manhole on the top dome and at the periphery. The G.I. pipes will be supported on R.C.C. postsof 100 mm dia or on the posts made of 50 X 50 X 6 mm M.S. angle section, spaced at intervals not more than 1.5 m.Proper ventilator at top dome in circular shape of 1.2 m dia along with an R.C.C. cover of minimum 1.50 m dia and 7.5 cm thicknes.The space between top dome and R.C.C. cover should be covered with mosquito net of standered qualitity along with expended mentaled jail.Electro Megnatic Flow Meter.Lightening conductor as per I.S.S. 2309 of its latest amendments of latest electricity rules. It should consistproper elevation rod with 5 or more fork points proper down conductors of prescribed mental of proper size prescribed by ISS 2309-1969 and ISS 3013-1966.D.I. manhole of min 60 X 60 cm size made of M.S. channel section with adequate cover made of M.S. sheet of minimum 3mm thickness hinged with manhole with locking arrangment. This manhole should be fixe at top dome at proper place.suppply od fixing of all down pipes and valves as per Tender document . includingsoil testing (detail specification as per tender document) 2 Zone -2 1600KL/18M 3 Zone -3 1700KL/18M 4 Renovation of R.C.C Over Head Tank (OHT) 5 Dismantiling of OHT DemagedFlooring Scrappingofold Surface OHT leakage RepairingPressure GroutingCement and water Proofing Coumpond Chemicalinternal wall and bottom dome to making of water tightness oftank body Repairing of Railing of Stair and Balcony with 20mm GI Pipe including changing of old pipe and refixing new pipe with angle ironpost Supply and Fixing of MS Stair Gate with box in 1/2 flight primar and painting complete cover and steel mosqueteo mesh in ventilatorlightening conductor making proper earthing Supply and Fixing ofDigital Water Level Indicator .Painting of OHT Shuttering centringflooring Painting two coats of approved paint Apex Ultima ofOHT including supply of all materials, labour and T&P etc required for Proper completion of the work in External of whole OHT with writing Of Scheme Details in tank Body .Ladder inside and outerside of tank bodyWith railing. Repairing & Paintingof inlet, outlet, overflow and washoutpipe with black japan paint and flow mark with white paint.Replacement / repairing sluice valve and chamberwith all material etc complete.,all work instructed by engineer in charge 6 Zone -1 7 Existing Tank 8 Construction of R.C.C clear water reserviour (C.W.R) cum pump house of various at different site 9 Design & supply of allmaterial T&P etc and constructRCC CWR cum pump house offollowing capacity with GI pipes railling consisting of 3 rows of 20 mm dia G.I pipe and angle iron posts of the dome periphery, S.S ladder from ground level to top of tank andaluminium ledder inside the tank, locking device, ventilator, supply and fixing digitalwater level indicator, 25mm PCC 1:2:4 over 80mm PCC 1:4:8 in apron, 150 mm semicircular drain around the tank, two coats of apex paint and testing of tank for water tightness etc. and also including the cost of supply and fixing of all necessary pipes and valves etc all complete as per approved design and drawing.(Detail specification as per tender document) 10 575 KL in Zone 2 11 625KL in Zone 3 12 Rising Main 13 Supply ofDI K-7/K-9 Pipes of follwing sizes (Dia in mm) / Thickness as IS 8329/2000 or its latest amendment with jointing materials, specials of sizes required during construction included jointing material upto site of work included loading unloading cartage insurance, etc all completed but exclusive of GST in various zone as per the drawing and approval to Engineer. 14 DI K-7 200mm Dia 15 DI K-7 250mm Dia 16 DI K-7 300mm Dia 17 DI K-7 400mm Dia 18 Supply of following size ofSluice Valves/ Scour Valves,capable for working pressure of 10 kg/cm2 Fire hydrants & Air Valves as per relevent I.S. Codeor its latest amandement. Up tosite store Including loading, unloading & cartage, taxes duties insurance , exclusive GST etc all complete. As per IS: 2906-1969. 19 Air Valve as per as I.S : 14845 20 20 mm dia 21 D.I. D/F Sluice valve/ Scour valve 200mm Dia 22 Cartage of following size (dia in mm.) of DI K-7/K-9 pipesand specials includingjointingmaterials from store to site of worklowering the same into excavated pipe line trenches true toalignment and gradiant and jointing the same including testing of pipe line aincluding supply of all materials labaour T&P etc complete also and as per direction of engineer incharge 23 DI K-7 200mm Dia 24 DI K-7 250mm Dia 25 DI K-7 300mm Dia 26 DI K-7 400mm Dia 27 Carting of following size of Sluice Valves/ Scour Valves,from store to site of work and lowering them into the trenches, fixing in position and jointing them with Pipe line and testing etc including supply of jointing materialand also including supply of all material and construction of suitable P.C.C Support below fittings etc. complete. 28 Air Valve as per as I.S : 14845 29 20 mm dia Dia 30 D.I. D/F Sluice valve/ Scour valve 200mm Dia 31 Dismantling of following types of roads including sorting out of servicable matarials stacking and disposal of unservicable materials with in a distance of 50 m. including supply of labour specials T&P etc. required for proper completion of work and road should be mortarable within 7 days after laying of pipe line. 32 Interlocking tile 33 C C Road 34 Bitumenous Road 35 B.O.E Road 36 Reinstatement of following types of roadsincluding supply of required new matarials & reinstatement the same includng supply of required for proper completion of work.supply of all materials labour T&P etc complete and as per direction of engineer incharge and specificationand conditions in tender dpcument 37 Interlocking tile 38 C C Road 39 Bitumenous Road 40 B.O.E Road 41 Excavation for pipe line trenches in ordinary soil use ofspecialT&P etc. with lift upto 1.5 m lead upto 50 mincluding filling back of excavated earth into trenches and watering ranmming dressing and removal of surpluas earthas direcetedincluding supply of all materials labour T&P etc complete and as per direction of engineer incharge. also includes barricading and dewatering (if required ) oftrench. 42 R.C.C. Thrust block with cement, core sand, and 20mm gauges stone ballast in propotion of 1: 1.5:3 in thrust block of pipe line including reinforcementand its bending the same with 0.08 mm thick binding wire in position and necessary shuttering including proper curing and supply of all materials, labour and T&P etc required for proper completion of work. 43 Thrust Block 44 Provision for Road crossing including all materials, labour and T&P etc. complete. It includes supply of D.I. pipe of necessary size for encasing, cement concrete and Brickwork for pillars and any other job for proper completion of work. 45 For crossing of road up to 3.5 m wide 46 For crossing of road up to 7.0 m wide 47 Provision for Road crossing including all materials, labour and T&P etc. complete. It includes supply of D.I. pipe of necessary size for encasing, cement concrete and Brickwork for pillars and any other job for proper completion of work. 48 For crossing of nalla upto 3.5 m wide 49 For crossing of nalla upto 20 m wide 50 Constuction of following type of chamber as per type design & drawing & as per diretion of engineer incharge including all supply of materials etc. 51 Sluice valve/Scour Valve chamber (Masonary type ) 52 Air Valve chamber 53 DISTRIBUTION NETWORK 54 Supply ofHDPE Pipes grade PE 100/ PN 6 of follwing sizes (Dia in mm) / Thickness as IS 4984/2016 or its latest amendment with electrofusion jointing materials, specials and fittings of sizes required during construction included jointing material upto site of work included loading unloading cartage insurance, etc all completed but exclusive of GST in various zone as per the drawing and approval to Engineer. 55 HDPE PIPE GRADE PE 100/ PN 6- 90 mm 56 HDPE PIPE GRADE PE 100/ PN 6- 110 mm 57 HDPE PIPE GRADE PE 100/ PN 6- 125 mm 58 HDPE PIPE GRADE PE 100/ PN 6- 140 mm 59 HDPE PIPE GRADE PE 100/ PN 6- 160 mm 60 Supply of ISI Marked or its relevant code DI K-7 Pipes of follwing sizes (Dia in mm) with jointing materials and specials, during construction as per latest I.S amendement upto site of work included loading, unloading, cartage insurance, etc all completed but exclusive of GST in various zone as per the drawing and approval to Engineer 61 D.I. K-7/ 150 mm 62 D.I. K-7/ 200 mm 63 D.I. K-7/ 250 mm 64 D.I. K-7/ 300 mm 65 Supply of following size ofSluice Valves/ Scour Valves,capable for working pressure of 10 kg/cm2 Fire hydrants & Air Valves as per relerelavent I.S.I or its latest amandement. Up to store Including loading, unloading & cartage, taxes duties insurance etc all complete. As per IS: 2906-1969. 66 Air Valve as per as I.S : 14845 67 20 mm. dia Air Valve 68 D.I. D/F Sluice valve/ Scour valve 69 80 mm dia. 70 100 mm dia. 71 125 mm dia. 72 150 mm dia. 73 200 mm dia. 74 250 mm dia. 75 300 mm dia. 76 Fire hydrant (80 mm dia.) 77 Dismantling of following types of roads including sorting out of servicable matarials stacking and disposal of unservicable matarials with in a distance of 50 m. including supply of labour specials T&P etc. required for proper completion of work 78 Interlocking tile 79 C.C Road 80 Bituminous Road 81 B.O.E Road 82 Excavation for pipe line trenches in ordinary soil use ofspecialT&P etc. with lift upto 1.5 m lead upto 50 mincluding filling back of excavated earth into trenches and watering ranmming dressing and removal of surpluas earth as direcetedincluding supply of all materials labour T&P etc complete and as per direction of engineer incharge. also includes barricading and dewatering (if required ) oftrench. 83 Cartage fromstore to site of work for following size (dia in mm)HDPE pipes and Specials coupling, fittings, and lowering the same into trenches and laying true to alignment and gradiant including testing of pipe lines cuttings of pipes for making up the length and making joints with electrofusion couplers, bands, tees, endcap etc. with electrofusion machinery including all jointing materials, labour, T&P etc required for proper completion of work. (excluding cost of trenching) 84 HDPE PIPE GRADE PE 100/ PN 6- 90 mm 85 HDPE PIPE GRADE PE 100/ PN 6- 110 mm 86 HDPE PIPE GRADE PE 100/ PN 6- 125 mm 87 HDPE PIPE GRADE PE 100/ PN 6- 140 mm 88 HDPE PIPE GRADE PE 100/ PN 6- 160 mm 89 Cartage of DI K-7 pipes and specials of following size (dia in mm)from store to site of work, lowering them into trenches and laying true to alignment and gradiant including testing of pipe line but excluding cost of trenching including all supply of Labour T&P etc complete required for proper completion of work. 90 D.I. K-7/ 150 mm 91 D.I. K-7/ 200 mm 92 D.I. K-7/ 250 mm 93 D.I. K-7/ 300 mm 94 Carting of following size of Sluice Valves/ Scour Valves, Fire hydrants & Air Valves from store to site of work and lowering them into the trenches, fixing in position and jointing them with Pipe line and testing etc including supply of jointing materialand also including supply of all material and construction of suitable P.C.C Support below fittings etc. complete. 95 20 mm. dia Air Valve 96 D.I. D/F Sluice valve/ Scour valve 97 80 mm dia. 98 100 mm dia. 99 125 mm dia. 100 150 mm dia. 101 200 mm dia. 102 250 mm dia. 103 300 mm dia. 104 Fire hydrant (80 mm dia.) 105 R.C.C. Thrust block with cement, core sand, and 20mm gauges stone ballast in propotion of 1: 1.5:3 in thrust block of pipe line including reinforcementand its bending the same with 0.08 mm thick binding wire in position and necessary shuttring including proper curing and supply of all materials, labour and T&P etc required for proper completion of work. 106 Thrust Block 107 Reinstatement of following types of roadsincluding supply of required new matarials & reinstatement the same includng supply of required for proper completion of work.supply of all materials labour T&P etc complete and as per direction of engineer incharge specificationand conditions in tender dpcument 108 Interlocking tile 109 C.C Road 110 Bitumenous Road 111 B.O.E Road 112 Supply of all matarial labour T&P etc and constuction of following type of chamber as per type design & drawing & as per diretion of engineer incharge . 113 Sluice valve chamber 114 Scour Valve Chamber 115 Air Valve chamber 116 fire hydrant chamber 117 Provision for Road crossing including all materials, labour and T&P etc. complete. It includes supply of D.I. pipe of necessary size for encasing, cement concrete and Brickwork for pillars and any other job for proper completion of work. 118 For crossing of road up to 3.5 m wide 119 For crossing of road up to 7.0 m wide 120 Provision for Road crossing including all materials, labour and T&P etc. complete. It includes supply of D.I. pipe of necessary size for encasing, cement concrete and Brickwork for pillars and any other job for proper completion of work. 121 For crossing of nalla upto 3.5 m wide 122 For crossing of nalla upto 20 m wide 123 Building works 124 Construction of Pump House Cum Chloronome (3.0 M X 2.5 M X 3.0 M , 1.8M X 1.2 M X 3.0 M, 1.5 WIDE VARANDAH)as per approved drawing and design based on RCCsingle reamed pile foundation , foundation beam, D.P.C. ,Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc,t concrete floor andapron on all sides ,by pass chamber ,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish ,Finishing walls with waterproof cement paint of approved make and quality yover one priming coat on new work with two coats to give an even shade, Supply of all material labour T&p complete as per instruction of engineer in charge. 125 Zone -1,2.3 126 Repairing of Pump HouseAs required including Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc,t concrete floor andapron on all sides ,bypasschamber,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish,Finishing walls with waterproof cement paint of approved make and qualityover o ne priming coat on old work with two coats to give an even shade,Supply of all material labour T&p complete as per instruction of engineer in charge. 127 Construnction of a half set of (area 45 sqm) one no. single Room staff quarters for Operator staff, pump operator , chaukidaar, pump attendent and other as per approved drawing and design based on RCCsingle reamed pile foundation , foundation beam, D.P.C. ,Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc,concrete floor andapron on all sides ,by pass chamber ,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish ,Finishing walls with waterproof cement paint of approved make and quality yover one priming coat on new work with two coats to give an even shade, Supply of all material labour T&p complete as per instruction of engineer in charge 128 Zone-1 ,2, 3 129 Construction of office building /admin Block(15X10X3.60) as per approved drawing and design based on RCCfram structure with cpwd / PWD norms and specification for OFFICE BUILDINGS including Supply of all material labour T&p complete as per instruction of engineer in charge 130 Sub station building consisting HT pannel room (5*4.5*3.6),MCS room(5*4.5*3.6) and meter room (4*3m*3.6)at praposed CWR site of zone 2 and 3 131 HT pannal room as per approved drawing and design based on RCCsingle reamed pile foundation , foundation beam, D.P.C. ,Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc,t concrete floor andapron on all sides ,by pass chamber ,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish ,Finishing walls with waterproof cement paint of approved make and quality yover one priming coat on new work with two coats to give an even shade, Supply of all material labour T&p complete as per instruction of engineer in charge 132 Master control scada room(5.0x4.5x4.0m) as per approved drawing and design based on RCCsingle reamed pile foundation , foundation beam, D.P.C. ,Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc, concrete floor andapron on all sides , cable duct and other ,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish ,Finishing walls with waterproof cement paint of approved make and quality yover one priming coat on new work with two coats to give an even shade, Supply of all material labour T&p complete as per instruction of engineer in charge 133 Meter room as per approved drawing and design based on RCCsingle reamed pile foundation , foundation beam, D.P.C. ,Ist class brick work ,M.S. Angle iron chaukhat of 50mm x 50mm x 6mm size for doors and windows, lintels, sun, shades slab etc, concrete floor andapron on all sides,Painting and varnishing of new iron work with one coat priming and two coat of approved apex paint and varnish ,Finishing walls with waterproof cement paint of approved make and quality yover one priming coat on new work with two coats to give an even shade, Supply of all material labour T&p complete as per instruction of engineer in charge 134 Construction of 1.8m high boundary wall on pile foundation as per approved design and drawingand as per specification given in bid document inluding painting with 2 coats of all waether apex paint over one coat primer painting primer coat including supply of all material labour T&P etc for propercompletion of works as per instruction of engineer in charge. 135 Water Campus Zone 1,2,3 136 Filling of earth of lower portion including carting of earth upto 10 km including ramming , levelling and dressing at water works campus. 137 Provide all materials, labour, T&P etc Required for proper completion of work and construct Interlocking Tiles approach road, laid dry and joints intact with coarse sand mortar including preparation of base as per specifications and instructions of engineer incharge. 138 Water Campus Zone 1,2,3 139 Construnction of Drain in Water works Campus30 x 30 cm including labour material and t&p all complete as per specifications and instructions of engineer incharge. 140 Zone-1 ,2,3 141 Dismental of Old OHT in zone 2 400 KL/10 M satgingin fornt of fire station konch including labour material, scaffoldingand t&p all complete as per specifications and instructions of engineer incharge. 142 NEW HOUSE CONNECTION 143 Making new House Connectionwith Distribution main of following dia and type of road including Dismantling and Reinstatement of road . Supply, cartingof elecrofusion specials as Saddel ,Tee ,Bend,brass ferrule, Union,H.D.P.E. pipe , HDPE adeptor ,GI pipe for drain crossing and avobe GL,loweringtheminto trenches , fixing them with CC block and clampincluding bailing out of water necessary excavation for connection with brass Tap including all labour , T&P etc. required for proper completion of the work. 144 In C.C. Roads 145 For 90 mm to 110mm dia 146 For 125 mm to 160 mm dia 147 For 180 mm to 250 mm dia 148 For 250 mm to 300mm dia 149 In Bitumenous Roads 150 For 90 mm to 110mm dia 151 For 125 mm to 160 mm dia 152 For 180 mm to 250 mm dia 153 For 250 mm to 300mm dia 154 In B.O.E. Roads 155 For 90 mm to 110mm dia 156 For 125 mm to 160 mm dia 157 For 180 mm to 250 mm dia 158 For 250 mm to 300mm dia 159 In C.C. Interlocking Tiles Roads 160 For 90 mm to 110mm dia 161 For 125 mm to 160 mm dia 162 For 180 mm to 250 mm dia 163 For 250 mm to 300mm dia 164 SHIFTING HOUSE CONNECTION 165 Shifting of house connection from extsting distribution line to new pipe line in followingdia,withsupply of H.D.P.E. Average 6.00 mtr includingelectrofusion specials, Brass ferrule, Electrofusion Saddle clamp,tee bend ,union ,brass tap etc. of suitable size, resting on cc platform below ground level T&P etc. including excavation, laying and jointing for proper completion of work as per instructions of Engineer-in-charge includingthe cost of baling out and subsequent backfilland repair of subsequent leakages of joints, fittings and specials during work. 166 In C.C. Roads 167 For 90 mm to 110mm dia 168 For 125 mm to 160 mm dia 169 For 200 mm to 250 mm dia 170 In Bitumenous Roads 171 For 90 mm to 110mm dia 172 For 125 mm to 160 mm dia 173 For 200 mm to 250 mm dia 174 For 250 mm to 300mm dia 175 In B.O.E. Roads 176 For 90 mm to 110mm dia 177 For 125 mm to 160 mm dia 178 For 200 mm to 250 mm dia 179 In C.C. Interlocking Tiles Roads 180 For 90 mm to 110mm dia 181 For 125 mm to 160 mm dia 182 For 200 mm to 250 mm dia 183 For 250 mm to 300mm dia 184 E&M WORKS 185 TUBEWELLCONSTRUTION(SIZE300MMX200MM) 186 Resistivity Survey of Tubewell Site 187 Transportation of rig machine erection, dismantling and associated T&P Complete in all respect including required all material , labour etc. 188 DRILLINGOFTUBEWELLBORE 189 Drilling of 625 mm. dia bore from G.Į. to 70 M. BGĮ (12x 70 mtr) 190 Drilling of 500 mm. dia bore from 70 BGĮ to 100 M. BGĮ (12x30mtr) 191 Drilling of 500 mm. dia bore from 100 BGĮ to 125 M. BGĮ (12x25mtr) 192 Įogging of bore hole by electirc logger 193 TUBEWELLASSEMBLY-MSERWTubewellassemblywithall required parts like plain pipe, slotted pipe, MS rings, well cap, bail plugclamp,reducer,centralguide,supportstructureetc.as required and as per typed design complete in all respect. 194 300 mm. dia 7.1 mm thick MSERW Plain Pipe with MS ring & reducer 195 200 mm.dia 7.1 mm thick M.S. Plain pipe & Slotted pipe with MS ring 196 LoweringofTubewellassemblydulyweldedincludingwelding electrode 197 300 mm. dia 7.1mm thick MSERW Plain / Slotted Pipe (12x62mtr) 198 200 mm. dia Plain/Slotted Pipe 63 M. BGĮto 100 M. BGĮ(12x38mtr) 199 200 mm. dia Plain/Slotted Pipe 101 M. BGĮto 112 M. BGĮ (12x12mtr) 200 Supply & Shruoding of Įal Kuan Pea Gravel 1.6 to 4.8 mm. size for Tubewell (12x36cum) 201 DEVELOPMENTOFTUBEWELL 202 Transportation, Erection, Dismantling of 250 P.S.I. Compressor. 203 Charges for Development by 250 P.S.I. Compressor per hour.(12x55 hrs) 204 Transportation, Erection, Dismantling of 2 Cusec O.P. Unit and yeild Test. 205 Charges for Development by 2 Cusec O.P. Unitper hour.(12x75hrs) 206 ChemicalandBacteriological testofwatersampleform departmentel / NABĮ approved lab. 207 CLEARWATERSUBMERSIBLEPUMPINGPLANTFORTUBEWELLSTOOHTZONE-1 208 Supply,installation,testingandcommissioningofClearwater submersiblepump(IS9236)completewithelectricmotor(IS8034) capable to operate on 380/420 volts 3 phase 50 c/s A.C. Capable for giving 900LPM,62MtrHead,25HPforNew Tubewell. 209 Supply,installation,testing andcommissioningof Main Piping & Valves with24Mtr.Columnpipe,bend,Tee,powerwiring,earthing,painting, wiring of pump house (Internal & External)complete in all respect with all required material, T&P labour 100mmDia.size. 210 Supply of 3 Mtr Įong Heavy duty exta Coloum pipe 100 mm Dia. Size (8 No for each TW ) 211 Supply of Motor operated actuators forsluice valve suitable for SCADA operationwithlimitswitches,autodeclutchformanualoperationin emergencyetcasperrelevantISsuitablefor100 mm dia size sluicevalve 212 Supply of D.I./ D.F. Dismantling Joints is a variable length Double Flanged ShortPiececonstitutedbya flange/ SpigotTailpieceinsertedintothe other Tailpiece which allows the distance between the two flanges to be variedwithincertainlimitsthusprovidingavariabledistancepiece betweentwofixedflangeenddeviceslikePumpsandValves.The Dismantling Joint to be supplied complete with Sealing Rubber Gaskets of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel (Zinc Coated) Nut Bolts of 100mm diasize 213 ExtraSubmersibleflatcoppercondutorcable3Cx6sq.mmPVC Sheathed double run (2Rx30m = 60 mtr for each TW) 214 Supply& laying of Į.T. XĮPE insulatedarmouredaluminiumconductor cable of 1.1 KV grade Material :- H4- Grade aluminium conductor of purity>99.6%&asperIS:1554P-I/IS:7098P-(I),conductorshallhave electrolytic aluminium confirming to IS 8130, IS 3975-1999.From transformer to Main ĮT panel of 3.5Cx 35Sq.mm. 215 Pumping Plant Motor inspection, B&Į and Challan fee 216 MOTORCONTROLCENTER(MCC)PANEL:-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 / IS:2147, considered Earth Bus-Bar-GI Strip compitable to SCADA operation with RS485 Port consisting of63 A, 50KA, TPN, MCCB microprocessor baseed(O/C,S/C) release - 1 No , Spreader Įinks & Extended ROH for - 1 No, 3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A-1Nos,CTFormeterResinCastCĮ-1400A/5A,15VA-3Nos,Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Įink - 1 No. 217 Supply of Air Cooled Digital soft starter suitable for the ĮT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including line contactors suitable for next standard higher KW rating, Over & Under load protection, short circuit & single phasing protection with frequency meter, Ammeter,Voltmeter,indicatinglamp6Nos, ĮED ON/OFF type and Start/StoppushbuttonandInstrumentFuses,suitabletoSCADAoperation with RS485 Port of rating capacity 25HP/18.50KW 218 Supplyofmicroprocessorbasedthreephasesensingpowerfactor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k setting according to targeted powerfactor setting, the relay shall have digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multiparameterlike KW, KVA, KVAR rating capacity of 25KVAR 219 Supply of Servo Controlled Automatic Voltage stabilizer suitable for out put voltage of 415 Volt +/-1%, 3 Ph, 50 Hz, with copper wound transformer (air/oilcooled).Thestabilizer shall functionsatisfactorily evenif incoming supply is unbalanced between phases within range of 10%. The stabilizer should be constructed in cubical box, with bi-directional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and out put voltage, Auto/Manual selector switch, Raise/Įow push buttonsetc.Suitable capacity termination stripsandbusbars for incoming and out going cable should be provided. All three phases shall beindependentlymonitoredandcorrected(Operatingvoltage240V- 500V), 415 volt, 3Phase, 50Hz of following capacity of 40KVA 220 Supply of Change over or by pass switch rating capacity 63Amp 221 Supply of 2 Ton 4.5 mtr lift chain pully block 222 SupplyofAutophasereversalunit with inbuilttimedelay& enclosure (conforming to IEC:60947-1 & IEC:60947-b-1) 63Amprating 223 Supply of CE/UĮ Certified Surge protector for control panel 224 Providing & Fixing of IK07 IP-66 protected high power ĮED flood light system with Pressure diecast aluminium housing ĮM6/ ADC12 material 50 Watt Flood light 225 SupplyofAutomatic/SCADAoperatedelectromegnaticchlorination dozzer system 226 INSTRUMENTATIONWORK 227 Supply of CE/UĮ Certified pressure transmitter CE markd with following technical parametersand Interfacing with PĮC panel including mounting arrangement.Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68 228 SupplyofCE/UĮCertifiedFullBoreElectromagneticFlowMeterof approved make of following dia and specifications complete: Media: Water (Raw/Chlorinated) , Pressure :up to 1.0MPa, Process temp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI 316Į /Hastelloy C276/Tantalum,ĮiningMaterial:HardRubber/ Neoprene/Poly-urethane(PU) , Flange : SS /CS, Flange Standard & Rating:ANSI150,Coilhousing:SSAISI304/CarbonSteel/DieCast Aluminium,with anticorrosive paint & provide completelysealed(leak proof)constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5% M.V.- velocity 0.3 to 10 m/s, Transmitter/ signa convertorEnclosure: Die CastAluminium,Power Supply : 80-240V AC - 5OHz, Output 1 : 4-20 mA, Output 2: Pulse, Communication Output : RS 485/ Heart,Display Type: ĮCD/ ĮED Display,Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68 for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable, of100mmdia sizeatoutle. 229 CE & UĮ Certified PĮC/ RTU in IP 54 enclosure suitable to communicate with intelligent GSM Based modem unit with CPU and Power Supply with analogandDigitalParameterandfeaturesasspecified tostoreand transmit data on GSM backbone, RTU designed with logic to tansfer data atmultiplestationsandalsocompatibleforsatellitecommunication alongwithcontrolpanelwithIP54Protection,Industrialgradeforall equipment and 24V and power supply for Tubewell & OHT 230 GSM/GPRS based wireless communication with 4G modem for RTU/PĮC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer, antenna made for pumping plantwith SIM andrecharge for 1 year 231 Supply of CE/UĮ cirtified of Radar type level transmitter CE marked with following technical parameters and Interfacing with PĮC panel including mounting arrangement with inbuild battery of 5 year life forOHTOutput-4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68 232 CE&UĮCertified7 HMItouchscreensuitabletocommunicationwith PĮC/RTU for local display & control of process parameters 233 CE/UĮ Certified Intelligent energy meters 234 SupplyofElectricallyMotoroperatedactuatorwithbracketfor sluice valve suitable for SCADA operation with limit switches, auto de clutch for manual operation in emergency etcas per relevant IS suitable for 300 mmdia sizesluice valveat OHT outlet 235 Completecablingforinstrumentation/SCADAequipmentswithpower supply of panels form source for Tubewell & OHT 236 Security Survelliance IP Camera with all required accessories 237 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS: 15683:2006 238 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 239 Installation,testing and comissioning of pumpingplant & associated all equipmentsas per approveddrawing shall be done by bidder including electrical resistance rubber mats and painting of pumping plant & main piping-valves. 240 Testing of Pumping Plant & Control Panel & valves etc at Manufacturer Works 241 CLEARWATERSUBMERSIBLEPUMPINGPLANTFORTUBEWELLSTOCWRZONE-2 242 Supply,installation,testingandcommissioningofClearwater submersiblepump(IS9236)completewithelectricmotor(IS8034) capable to operate on 380/420 volts 3 phase 50 c/s A.C. Capable for giving 800LPM,46MtrHead,20HPforExsistingTubewell . 243 Supply,installation,testingandcommissioningofClearwater submersiblepump(IS9236)completewithelectricmotor(IS8034) capable to operate on 380/420 volts 3 phase 50 c/s A.C. Capable for giving 900LPM,46MtrHead,20HPfor05Nos.NewTube well. 244 Supply,installation,testing andcommissioningof Main Piping & Valves with24Mtr.Columnpipe,bend,Tee,powerwiring,earthing,painting, wiring of pump house (Internal & External)complete in all respect with all required material, T&P labour 100mmDia.size . 245 Supply of 3 Mtr Įong Heavy duty exta Coloum pipe 100 mm Dia. Size (8 No for each TW ) 246 Supply of Motor operated actuators forsluice valve suitable for SCADA operationwithlimitswitches,autodeclutchformanualoperationin emergencyetcasperrelevantISsuitablefor100 mm dia size sluice valve 247 Supply of D.I./ D.F. Dismantling Joints is a variable length Double Flanged ShortPiececonstitutedbya flange/ SpigotTailpieceinsertedintothe other Tailpiece which allows the distance between the two flanges to be variedwithincertainlimitsthusprovidingavariabledistancepiece betweentwofixedflangeenddeviceslikePumpsandValves.The Dismantling Joint to be supplied complete with Sealing Rubber Gaskets of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel (Zinc Coated) Nut Bolts of 100mm diasize 248 ExtraSubmersibleflatcoppercondutorcable3Cx6sq.mmPVC Sheathed double run (2Rx30m = 60 mtr for each TW) 249 Supply& laying of Į.T. XĮPE insulatedarmouredaluminiumconductor cable of 1.1 KV grade Material :- H4- Grade aluminium conductor of purity>99.6%&asperIS:1554P-I/IS:7098P-(I),conductorshallhave electrolytic aluminium confirming to IS 8130, IS 3975-1999.From transformer to Main ĮT panel of 3.5Cx 35Sq.mm. 250 Pumping Plant Motor inspection, B&Į and Challan fee 251 MOTORCONTROLCENTER(MCC)PANEL:-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 / IS:2147, considered Earth Bus-Bar-GI Strip compitable to SCADA operation with RS485 Port consisting of63 A, 50KA, TPN, MCCB microprocessor baseed(O/C,S/C) release - 1 No , Spreader Įinks & Extended ROH for - 1 No, 3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A-1Nos,CTFormeterResinCastCĮ-1400A/5A,15VA-3Nos,Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Įink - 1 No. 252 Supply of Air Cooled Digital soft starter suitable for the ĮT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including line contactors suitable for next standard higher KW rating, Over & Under load protection, short circuit & single phasing protection with frequency meter, Ammeter,Voltmeter,indicatinglamp6Nos, ĮED ON/OFF type and Start/StoppushbuttonandInstrumentFuses,suitabletoSCADAoperation with RS485 Port of rating capacity 20HP/15KW 253 Supplyofmicroprocessorbasedthreephasesensingpowerfactor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k setting according to targeted powerfactor setting, the relay shall have digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multiparameterlike KW, KVA, KVAR rating capacity of 20KVAR 254 Supply of Servo Controlled Automatic Voltage stabilizer suitable for out put voltage of 415 Volt +/-1%, 3 Ph, 50 Hz, with copper wound transformer (air/oilcooled).Thestabilizer shall functionsatisfactorily evenif incoming supply is unbalanced between phases within range of 10%. The stabilizer should be constructed in cubical box, with bi-directional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and out put voltage, Auto/Manual selector switch, Raise/Įow push buttonsetc.Suitable capacity termination stripsandbusbars for incoming and out going cable should be provided. All three phases shall beindependentlymonitoredandcorrected(Operatingvoltage240V- 500V), 415 volt, 3Phase, 50Hz of30KVA capacity 255 Supply of Change over or by pass switch rating capacity 63Amp 256 Supply of 2 Ton 4.5 mtr lift chain pully block 257 SupplyofAutophasereversalunit with inbuilttimedelay& enclosure (conforming to IEC:60947-1 & IEC:60947-b-1) 63Amprating 258 Supply of CE/UĮ Certified Surge protector for control panel 259 Providing & Fixing of IK07 IP-66 protected high power ĮED flood light system with Pressure diecast aluminium housing ĮM6/ ADC12 material 50 Watt Flood light 260 INSTRUMENTATIONWORK 261 Supply of CE/UĮ Certified pressure transmitter CE markd with following technical parametersand Interfacing with PĮC panel including mounting arrangement.Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDAccuracy - +/- 0.1 % of full scale or betterEnclosure- IP 68 262 SupplyofCE/UĮCertifiedFullBoreElectromagneticFlowMeterof approved make of following dia and specifications complete: Media: Water (Raw/Chlorinated) , Pressure :up to 1.0MPa, Process temp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI 316Į /Hastelloy C276/Tantalum,ĮiningMaterial:HardRubber/ Neoprene/Poly-urethane(PU) , Flange : SS /CS, Flange Standard & Rating:ANSI150,Coilhousing:SSAISI304/CarbonSteel/DieCast Aluminium,with anticorrosive paint & provide completelysealed(leak proof)constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5% M.V.- velocity 0.3 to 10 m/s, Transmitter/ signa convertorEnclosure: Die CastAluminium,Power Supply : 80-240V AC - 5OHz, Output 1 : 4-20 mA, Output 2: Pulse, Communication Output : RS 485/ Heart,Display Type: ĮCD/ ĮED Display,Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68 for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable, of100mmdia size at delivery header 263 CE & UĮ Certified PĮC/ RTU in IP 54 enclosure suitable to communicate with intelligent GSM Based modem unit with CPU and Power Supply with analogandDigitalParameterandfeaturesasspecified tostoreand transmit data on GSM backbone, RTU designed with logic to tansfer data atmultiplestationsandalsocompatibleforsatellitecommunication alongwithcontrolpanelwithIP54Protection,Industrialgradeforall equipment and 24V and power supply for Tubewell 264 GSM/GPRS based wireless communication with 4G modem for RTU/PĮC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer, antenna made for pumping plantwith SIM andrecharge for 1 year 265 CE&UĮCertified7 HMItouchscreensuitabletocommunicationwith PĮC/RTU for local display & control of process parameters 266 CE/UĮ Certified Intelligent energy meters 267 Completecablingforinstrumentation/SCADAequipmentswithpower supply of panels form source for Tubewell 268 Security Survelliance IP Camera with all required accessories 269 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS:15683:2006 270 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 271 Installation,testing and comissioning of pumpingplant & associated all equipmentsas per approveddrawing shall be done by bidder including electrical resistance rubber mats and painting of pumping plant & main piping-valves. 272 Testing of Pumping Plant & Control Panel & valves etc at Manufacturer Works 273 CLEARWATERSUBMERSIBLEPUMPINGPLANTFORTUBEWELLSTOCWRZONE-3 274 Supply,installation,testingandcommissioningofClearwater submersiblepump(IS9236)completewithelectricmotor(IS8034) capable to operate on 380/420 volts 3 phase 50 c/s A.C. Capable for giving 800LPM,46MtrHead,20 HPforExsistingTubewell. 275 Supply,installation,testingandcommissioningofClearwater submersiblepump(IS9236)completewithelectricmotor(IS8034) capable to operate on 380/420 volts 3 phase 50 c/s A.C. Capable for giving 900LPM,46MtrHead,20HPfor05Nos.New Tube well . 276 Supply,installation,testing andcommissioningof Main Piping & Valves with24Mtr.Columnpipe,bend,Tee,powerwiring,earthing,painting, wiring of pump house (Internal & External)complete in all respect with all required material, T&P labour 100mmDia.size. 277 Supply of 3 Mtr Įong Heavy duty exta Coloum pipe 100 mm Dia. Size (8 No for each TW ) 278 Supply of Motor operated actuators forsluice valve suitable for SCADA operationwithlimitswitches,autodeclutchformanualoperationin emergencyetcasperrelevantISsuitablefor100 mm dia size sluice valve 279 Supply of D.I./ D.F. Dismantling Joints is a variable length Double Flanged ShortPiececonstitutedbya flange/ SpigotTailpieceinsertedintothe other Tailpiece which allows the distance between the two flanges to be variedwithincertainlimitsthusprovidingavariabledistancepiece betweentwofixedflangeenddeviceslikePumpsandValves.The Dismantling Joint to be supplied complete with Sealing Rubber Gaskets of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel (Zinc Coated) Nut Bolts of 100mm diasize 280 ExtraSubmersibleflatcoppercondutorcable3Cx6sq.mmPVC Sheathed double run (2Rx30m = 60 mtr for each TW) 281 Supply& laying of Į.T. XĮPE insulatedarmouredaluminiumconductor cable of 1.1 KV grade Material :- H4- Grade aluminium conductor of purity>99.6%&asperIS:1554P-I/IS:7098P-(I),conductorshallhave electrolytic aluminium confirming to IS 8130, IS 3975-1999.From transformer to Main ĮT panel of 3.5Cx 35Sq.mm. 282 Pumping Plant Motor inspection, B&Į and Challan fee 283 MOTORCONTROLCENTER(MCC)PANEL:-Single front, Indoor & floor mounted,cubical type Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shrouds and Gland Plate-3 mm thick) CRCA sheet duly power coateddust and vermin proof IP-54 / IS:2147, considered Earth Bus-Bar-GI Strip compitable to SCADA operation with RS485 Port consisting of63 A, 50KA, TPN, MCCB microprocessor baseed(O/C,S/C) release - 1 No , Spreader Įinks & Extended ROH for - 1 No, 3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A-1Nos,CTFormeterResinCastCĮ-1400A/5A,15VA-3Nos,Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Įink - 1 No. 284 Supply of Air Cooled Digital soft starter suitable for the ĮT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including line contactors suitable for next standard higher KW rating, Over & Under load protection, short circuit & single phasing protection with frequency meter, Ammeter,Voltmeter,indicatinglamp6Nos, ĮED ON/OFF type and Start/StoppushbuttonandInstrumentFuses,suitabletoSCADAoperation with RS485 Port of rating capacity 20HP/15KW 285 Supplyofmicroprocessorbasedthreephasesensingpowerfactor correctionrelaypanel,IEC/EN61000-6-(2&4)having3CTsensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k setting according to targeted powerfactor setting, the relay shall have digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multiparameterlike KW, KVA, KVAR rating capacity of 20KVAR 286 Supply of Servo Controlled Automatic Voltage stabilizer suitable for out put voltage of 415 Volt +/-1%, 3 Ph, 50 Hz, with copper wound transformer (air/oilcooled).Thestabilizer shall functionsatisfactorily evenif incoming supply is unbalanced between phases within range of 10%. The stabilizer should be constructed in cubical box, with bi-directional wheels for easy handling, necessary monitors and users controls on front panel such as indication, alarm, volt meter and selector switch for measuring input and out put voltage, Auto/Manual selector switch, Raise/Įow push buttonsetc.Suitable capacity termination stripsandbusbars for incoming and out going cable should be provided. All three phases shall beindependentlymonitoredandcorrected(Operatingvoltage240V- 500V), 415 volt, 3Phase, 50Hz of30KVA capacity 287 Supply of Change over or by pass switch rating capacity 63Amp 288 Supply of 2 Ton 4.5 mtr lift chain pully block 289 SupplyofAutophasereversalunit with inbuilttimedelay& enclosure (conforming to IEC:60947-1 & IEC:60947-b-1) 63Amprating 290 Supply of CE/UĮ Certified Surge protector for control panel 291 Providing & Fixing of IK07 IP-66 protected high power ĮED flood light system with Pressure diecast aluminium housing ĮM6/ ADC12 material 50 Watt Flood light 292 INSTRUMENTATIONWORK 293 Supply of CE/UĮ Certified pressure transmitter CE markd with following technical parametersand Interfacing with PĮC panel including mounting arrangement.Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDAccuracy - +/- 0.1 % of full scale or betterEnclosure- IP 68 294 SupplyofCE/UĮCertifiedFullBoreElectromagneticFlowMeterof approved make of following dia and specifications complete: Media: Water (Raw/Chlorinated) , Pressure :up to 1.0MPa, Process temp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI 316Į /Hastelloy C276/Tantalum,ĮiningMaterial:HardRubber/ Neoprene/Poly-urethane(PU) , Flange : SS /CS, Flange Standard & Rating:ANSI150,Coilhousing:SSAISI304/CarbonSteel/DieCast Aluminium,with anticorrosive paint & provide completelysealed(leak proof)constructionasperrequirement‘ofIEC 60529, Accuracy : + 0.5% M.V.- velocity 0.3 to 10 m/s, Transmitter/ signa convertorEnclosure: Die CastAluminium,Power Supply : 80-240V AC - 5OHz, Output 1 : 4-20 mA, Output 2: Pulse, Communication Output : RS 485/ Heart,Display Type: ĮCD/ ĮED Display,Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibration and configuration parametersand totalizer value during power failure, Protection category- IP 68 for sensor (flow tube) and IP 67 for transmitter/ convertor, including Surge Arrester, cable, of100mmdia size at delivery header 295 CE & UĮ Certified PĮC/ RTU in IP 54 enclosure suitable to communicate with intelligent GSM Based modem unit with CPU and Power Supply with analogandDigitalParameterandfeaturesasspecified tostoreand transmit data on GSM backbone, RTU designed with logic to tansfer data atmultiplestationsandalsocompatibleforsatellitecommunication alongwithcontrolpanelwithIP54Protection,Industrialgradeforall equipment and 24V and power supply for Tubewell 296 GSM/GPRS based wireless communication with 4G modem for RTU/PĮC Capable to transfer and gather data from remote sites to control stations all accessories included with signal enhancer, antenna made for pumping plantwith SIM andrecharge for 1 year 297 CE&UĮCertified7 HMItouchscreensuitabletocommunicationwith PĮC/RTU for local display & control of process parameters 298 CE/UĮ Certified Intelligent energy meters 299 Completecablingforinstrumentation/SCADAequipmentswithpower supply of panels form source for Tubewell 300 Security Survelliance IP Camera with all required accessories 301 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS:15683:2006 302 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 303 Installation,testing and comissioning of pumpingplant & associated all equipmentsas per approveddrawing shall be done by bidder including electrical resistance rubber mats and painting of pumping plant & main piping-valves. 304 Testing of Pumping Plant & Control Panel & valves etc at Manufacturer Works 305 CLEARWATERPUMPINGPLANTATPROPOSEDCWR(575 KL)ZONE -2TO PROPOSEDOHT(1600 KL)ZONE-2 306 SupplyofVerticaltypeself-waterlubricatedstatically, dynamically, hydraulically balanced turbinepump capable of dischargingat1450rpmthefollowingdutyconditionasgiven below due to all causes with surface discharge head confirming to IS:1710andasamendedasondatewithaccessoriesasperIS 5120/1977(Reconfirmed 2011) and as amended thereafter to suit the site condition.The Pump Bowl assemblyshall be FG: 260with 2% NiCi with CF8M impeller running at 1450 rpm., head shaft, SS line shaft, Rubberlineshaftbearing,C.I.Bearingretainer,Suction bell mouth, strainer, 5 mtr/suitable length column assembly, with vertical Solid shaft Squirrel cage induction motor(IS:126152011/IEC 60034-1) suitable for the above pump continuous rated TEFC IP-55 with ClassF insulationfor operationin AC, threePhase/50HZ (±5%), 415V (±10%), running with a speed of pump.CAPACITY:-3050LPM/36Mtr.HEAD /40HPMOTOR(2w+1s) 307 MAINPIPINGAND VALVES:- 308 SupplyofCIDFSingleDoor/MultiDoorNonreturn/refluxvalve conformingtoIS:5312/2003(partI&II)PN-1.0tobefixedafter pumps for 90% fast closing & 10% slow closing of 200mmdiasize 309 Supply of CIDFElectrically integrated actuater (Totally enclosed, weather-proof and dust proof construction with IP-67, protection class suitable for installationin any positionwithout lubrication, leakageorotheroperationaldifficultywithspecialgreasefilled gear box and suitable for manual operation for emergency which willautomaticallydis-engageonrestorationofpowertomotor and with 10 watt single phase space heater and continuous local mechanical position indicator and individually replaceable counter gear assembly and with two torque and four limit switches withS.S. flapandoperatedwith geardriven camsandof rating250 Volt, 5 Amp, AC/DC, torque switch dial and with TEFC squirrel cage induction)operatedsuitabletoSCADAoperationsluicevalve having body door cover of graded in cast iron to IS:210 Gr.Fg.260 body and door rings of SS ASTM A743 Gr.CF8 and bearing block of leadedtinbronzetoIS:318Gr.ĮTB2hingepinofstainlesssteel AISI:431.Valves generally conform to IS:5312.Flanges tobedrilled asperIS:1538Part-IV&VI. Valves aresuitable for hydrostatic test pressure of 10Kg./Cm2 for seat and 15Kg./Cm2 for body(PN- 1.0) of200mmat pumpdelivery 310 Supply of CIDFmanually operated sluice valve having body door coverofgradedincastirontoIS:210Gr.Fg.260bodyanddoor ringsofSSASTMA743Gr.CF8andbearingblockofleadedtin bronzetoIS:318Gr.ĮTB2hingepinofstainlesssteel AISI:431.Valves generally conform to IS:5312.Flanges tobedrilled asperIS:1538Part-IV&VI. Valves aresuitable for hydrostatic test pressure of 10Kg./Cm2 for seat and 15Kg./Cm2 for body(PN-1.0 Rating) Sluice Valve of300mm at Commonheader&bypass 311 SupplyofElectricallyMotoroperatedactuatorwithbracketfor sluice valve suitable for SCADA operation with limit switches, auto de clutch for manual operation in emergency etcas per relevant IS suitable for 450mmdiasizeforOHToutlet 312 Supplyandfabricationofmainpiping1mtroutsidethepump houseoffollowingsizes300 x 200 x 300 mm MS D/F Tee (10 mm thickness) -3 No200 mm MS D/F Pipe 0.50 mt. (10 mm thickness) - 3 No 200 mm MS D/F Pipe 1.00 mt.(10 mm thickness) - 3 No 300 mm MS D/F Pipe 1.00 mt.(10 mm thickness) - 3 No 300 mm MS D/F Pipe 2.00 mt. (10 mm thickness) -2 No 300 mm MS D/F (10 mm thickness) Bend 90o- 2 No 300 mm Blind Flange - 1 NoNecessary GI Nut Bolt’s & Rubber Packing - 1 Įot 313 Supply of D.I./ D.F. Dismantling Joints is a variable length Double FlangedShortPiececonstitutedbyaflange/SpigotTailpiece insertedintotheotherTailpiece whichallows thedistance betweenthetwoflangestobevariedwithincertainlimitsthus providing a variable distance piece between two fixed flange end deviceslikePumpsandValves.TheDismantlingJointtobe supplied complete with Sealing Rubber Gaskets of EPDM quality (IS:5382/1985Type-4),CastIronFollowerGlands andMild Steel (Zinc Coated) Nut Bolts of Following size 314 Dismantling joint 200 mm dia size at pump delivery 315 Dismantling joint 300 mm dia size at common header 316 3Ton capacity hand operated over head Travelling (HOT) crane H- Typesuitablefor a spanupto6 Mtrs, andtravellengthupto10 Mtrs. with clear lift upto 6 M including gear type chain pulley block and geared Travelling trolley complete with all accessories including girder. 317 MOTORCONTROLCENTER(MCC)PANEL:-Singlefront,Indoor&floormounted,cubicaltypePanelfactory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shroudsandGlandPlate-3mmthick)CRCAsheetdulypower coated dustandverminproofIP-54/IS:2147,consideredEarth Bus-Bar-GI Strip compitable to SCADA operation with RS485 Port consisting ofINCOMMINGSECTION320 A, 50KA, TPN, MCCB microprocessor baseed (O/C,S/C) release-1No,SpreaderĮinks&ExtendedROHfor-1No,3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CĮ-1400A/5A,15VA - 3 Nos, Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA - 3 Nos, CT Shorting Terminal 4 Nos, Neutral Įink - 1 No.OUTGOINGSECTION100 A, 50KA, TPN, MCCBmicroprocessor based (O/C,S/C) REĮEASE - 4 No, Spreader Įinks & Extended ROH for MCCB - 4 Nos., 63A TPN MCCB 35KA- 3 Nos. Terminal 63A 318 Supply of Air Cooled Digital soft starter suitable for the ĮT motor offered for operationin AC three Phase 50Hz (+/- 5%), 415V(+/- 10%)includinglinecontactorssuitablefornextstandardhigher KWrating,Over&Underloadprotection,shortcircuit&single phasingprotectionwithfrequencymeter,Ammeter,Voltmeter, indicatinglamp6Nos,ĮEDON/OFFtypeandStart/Stoppush buttonandInstrumentFuses,suitabletoSCADAoperationwith RS485 Port of rating capacity 40HP/30KW 319 Supplyofmicroprocessorbasedthreephasesensingpower factor correction relay panel , IEC / EN 61000-6- (2&4) having 3 CT sensing,sensitivityupto50milliampsecondarycurrent,self analysingautoc/ksettingaccordingtotargetedpowerfactor setting, the relay shall have digit display unit for displayof real power factor, targeted power factor, lag/lead capacitor switching status, alarmoutput for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like KW, KVA, KVAR rating capacity of 40KVAR 320 Supply & laying of 1.1 KV grade XĮPE insulatedun armoured multi strandcopperconductorcableof3C x 25 sq.mm fromcontrol PaneltorespectiveMotorswithlugsetc.(copperconductor should be electrlytic grade coppe, purity >99.97 % ISI markedas per IS:1554 P-I / IS:7098 P- I) 321 Supply &Fixing ofPowder coated GI Cable Tray 150mmx50mmx1.6mm 322 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick includingaccessories,andprovidingmasonryenclosurewith cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required according to latest IS:3043 323 Supplying and laying 50 mm X 6 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done byoverlappingandwith2 sets of brassnut bolt& spring washer spaced at 50mm) 324 Supply of ABC Dry Powder type Fire Extinguisher 4.5 kg conforming to IS: 15683:2006 325 Supply of Auto Phase reversal unit / Automatic switch with inbuilt the delay & enclosure (Confirms to IEC: 60947-1 & IEC: 60947-6-1) of 250Amp 326 S& F of all in one solar ĮED street light fixture with Integrated high efficientMonocrystallinepanel withĮithium(ĮiFePO4)Ferro Phosphate battery with BIS approved make .luminaire should be secondaryopticlensesforbetterdistributionwithdelivered efficacy of >100 Įumen per watt. Įuminaire can be supplied with Hybridswitchalongwithindicatortounderstandthesourceof power(eitherfromsolarorACsupply).shallhavecertificate tested fromMNRE approved Įab. Guarantee for total system is two years .Note: All the aboveshould be integrated and should be 1 system.make:Bajaj/Philips/Crompton.CompactSolar LED StreetLight-60W/12V/27AhwithGIpole 327 Internal&ExternalelectrificationofPumphouse 328 Twin tube light covered ĮED 20 Watt 329 450 mm dia exhaust fan 330 Providing & Fixing of IK07 IP-66 protected high power ĮED flood light system with Pressure diecast aluminium housing ĮM6/ ADC12 material 50 Watt Flood light 331 CompletewiringofPumphousewith1.5Sqmm&2.5Sqmm multistarnd copper conductor wire 1.1 KV with required 5A & 15A switches, ceiling rose 332 Supply of CE/UĮ Certified Surge protector for control panel 333 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 334 SupplyofAutomatic/SCADAoperatedelectromegnatic chlorination dozzer system 335 INSTRUMENTATIONWORK 336 Supply of CE/UĮ certified Full bore Electromagnetic Flow Meter of approved make of following dia and specifications complete: Media : Water (Raw/Chlorinated) , Pressure : up to 1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316Į/ HastelloyC276/Tantalum,Įining Material : Hard Rubber/ Neoprene/Poly-urethane(PU) , Flange : SS /CS, Flange Standard & Rating : ANSI 150, Coil housing : SS AISI 304/CarbonSteel/ DieCast Aluminium,with anticorrosive paint & provide completelysealed(leakproof)constructionas perrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V.- velocity0.3 to 10 m/s, Transmitter/ signa convertorEnclosure: Die Cast Aluminium,Power Supply : 80-240V AC - 5OHz, Output 1 : 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : ĮCD/ ĮED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibrationandconfigurationparameters and totalizer value during power failure, Protection category- IP 68forsensor(flowtube)andIP67fortransmitter/convertor, including Surge Arrester, cable, of300mm dia size at common header 337 SupplyofCE/UĮCertifiedpressuretransmitterCEmarkdwith followingtechnicalparameters andInterfacingwithPĮCpanel including mounting arrangement.Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68 338 SupplyofCE/UĮcirtifiedofRadartypeleveltransmitterCE marked with following technical parameters and Interfacing with PĮC panel including mounting arrangement forCWROutput-4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68 339 SupplyofCE/UĮcirtifiedofRadartypeleveltransmitterCE marked with following technical parametersand Interfacing with PĮC panel including mounting arrangement with inbuild battery of 5 year life forOHTOutput-4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68 340 CE&UĮCertifiedPĮC/RTUinIP54enclosuresuitableto communicatewithintelligentGSMBasedmodemunitwithCPU and Power Supply with analog and Digital Parameter and features as specified for each for each ZPS/OHT to store and transmit data onGSMbackbone,RTUdesignedwithlogictotansferdataat multiple stations and also compatible for satellite communication alongwith control panel with IP 54 Protection , Industrial grade for all equipment and 24V and power supply 341 GSM/GPRSbasedwirelesscommunicationwith4Gmodemfor RTU/PĮC Capable to transfer and gather data from remote sites to controlstationsallaccessoriesincludedwithsignalenhancer, antennamadeforpumpingplant withSIMand rechargefor1 year 342 CE&UĮCertifiedPĮC/RTUinIP54enclosuresuitableto communicatewithintelligentGSMBasedmodemunitwithCPU and Power Supply with analog and Digital Parameter and features as specified for each for each ZPS/OHT to store and transmit data onGSMbackbone,RTUdesignedwithlogictotansferdataat multiple stations and also compatible for satellite communication alongwith control panel with IP 54 Protection , Industrial grade for all equipment and 24V and power supply for OHT due to Outside the campus 343 GSM/GPRSbasedwirelesscommunicationwith4Gmodemfor RTU/PĮC Capable to transfer and gather data from remote sites to controlstationsallaccessoriesincludedwithsignalenhancer, antennamadeforpumpingplant withSIMand rechargefor1 year 344 CE & UĮ Certified 7 HMI touch screen suitable to communication with PĮC/RTU for local display & control of process parameters 345 CE/UĮ Certified Intelligent energy meters 346 Completecablingforinstrumentation/SCADAequipmentswith power supply of panels form source for CWR & OHT 347 Security Survelliance IP Camera with all required accessories 348 Toolset:-Spenners- 2 Nos,Adjustable Wrinch set - 2 Nos, size wrinches of different sizes - 1 Set, Gigital Tong tester - 1 Nos, Digital Clamp meter - 1 No, megger 5Mva- 1 No, Hydraulic crimping tool 500 Sq mmsize-1No,SandPPMmeasuringkit -1No,DigitalScrew Gauge 40mm size - 1 No, Inner & Outer pipe gauge set 500mm size-1Set, Fillergauges -1 Set,Electronic batteryoperatedwater level / depth gauge with meter marking upto 400 mtr depth - 1 No 349 Installation, testing and comissioning of pumping plant & associated all equipments as per approved drawing shall be done bybidderincludingchequerredplateandpaintingofpumping plant & main piping-valves. 350 Testing of Pumping Plant & Control Panel & valves etc at Manufacturer Works 351 CLEARWATERPUMPINGPLANTATPROPOSEDCWR(575 KL)ZONE-3TOPROPOSEDOHT(1750KL)ZONE-3 352 SupplyofVerticaltypeself-waterlubricatedstatically, dynamically, hydraulically balanced turbinepump capable of dischargingat1450rpmthefollowingdutyconditionasgiven below due to all causes with surface discharge head confirming to IS:1710andasamendedasondatewithaccessoriesasperIS 5120/1977(Reconfirmed 2011) and as amended thereafter to suit the site condition.The Pump Bowl assemblyshall be FG: 260with 2% NiCi with CF8M impeller running at 1450 rpm., head shaft, SS line shaft, Rubberlineshaftbearing,C.I.Bearingretainer,Suction bell mouth, strainer, 5 mtr/suitable length column assembly, with vertical Solid shaft Squirrel cage induction motor(IS:126152011/IEC 60034-1) suitable for the above pump continuous rated TEFC IP-55 with ClassF insulationfor operationin AC, threePhase/50HZ (±5%), 415V (±10%), running with a speed of pump.CAPACITY:-3250LPM/36Mtr.HEAD /40HPMOTOR(2w+1s) 353 MAINPIPINGAND VALVES:- 354 SupplyofCIDFSingleDoor/MultiDoorNonreturn/refluxvalve conformingtoIS:5312/2003(partI&II)PN-1.0tobefixedafter pumps for 90% fast closing & 10% slow closing of 200mmdiasize 355 Supply of CIDFElectrically integrated actuater (Totally enclosed, weather-proof and dust proof construction with IP-67, protection class suitable for installationin any positionwithout lubrication, leakageorotheroperationaldifficultywithspecialgreasefilled gear box and suitable for manual operation for emergency which willautomaticallydis-engageonrestorationofpowertomotor and with 10 watt single phase space heater and continuous local mechanical position indicator and individually replaceable counter gear assembly and with two torque and four limit switches withS.S. flapandoperatedwith geardriven camsandof rating250 Volt, 5 Amp, AC/DC, torque switch dial and with TEFC squirrel cage induction)operatedsuitabletoSCADAoperationsluicevalve having body door cover of graded in cast iron to IS:210 Gr.Fg.260 body and door rings of SS ASTM A743 Gr.CF8 and bearing block of leadedtinbronzetoIS:318Gr.ĮTB2hingepinofstainlesssteel AISI:431.Valves generally conform to IS:5312.Flanges tobedrilled asperIS:1538Part-IV&VI. Valves aresuitable for hydrostatic test pressure of 10Kg./Cm2 for seat and 15Kg./Cm2 for body(PN- 1.0) of200mmat pumpdelivery 356 Supply of CIDFmanually operated sluice valve having body door coverofgradedincastirontoIS:210Gr.Fg.260bodyanddoor ringsofSSASTMA743Gr.CF8andbearingblockofleadedtin bronzetoIS:318Gr.ĮTB2hingepinofstainlesssteel AISI:431.Valves generally conform to IS:5312.Flanges tobedrilled asperIS:1538Part-IV&VI. Valves aresuitable for hydrostatic test pressure of 10Kg./Cm2 for seat and 15Kg./Cm2 for body(PN-1.0 Rating) Sluice Valve of300mm at Commonheader&bypass 357 SupplyofElectricallyMotoroperatedactuatorwithbracketfor sluice valve suitable for SCADA operation with limit switches, auto de clutch for manual operation in emergency etcas per relevant IS suitable for 450mmdiasizeforOHToutlet 358 Supplyandfabricationofmainpiping1mtroutsidethepump houseoffollowingsizes300 x 200 x 300 mm MS D/F Tee (10 mm thickness) -3 No200 mm MS D/F Pipe 0.50 mt. (10 mm thickness) - 3 No 200 mm MS D/F Pipe 1.00 mt.(10 mm thickness) - 3 No 300 mm MS D/F Pipe 1.00 mt.(10 mm thickness) - 3 No 300 mm MS D/F Pipe 2.00 mt. (10 mm thickness) -2 No 300 mm MS D/F (10 mm thickness) Bend 90o- 2 No 300 mm Blind Flange - 1 NoNecessary GI Nut Bolt’s & Rubber Packing - 1 Įot 359 Supply of D.I./ D.F. Dismantling Joints is a variable length Double FlangedShortPiececonstitutedbyaflange/SpigotTailpiece insertedintotheotherTailpiece whichallows thedistance betweenthetwoflangestobevariedwithincertainlimitsthus providing a variable distance piece between two fixed flange end deviceslikePumpsandValves.TheDismantlingJointtobe supplied complete with Sealing Rubber Gaskets of EPDM quality (IS:5382/1985Type-4),CastIronFollowerGlands andMild Steel (Zinc Coated) Nut Bolts of Following size 360 Dismantling joint 200 mm dia size at pump delivery 361 Dismantling joint 300 mm dia size at common header 362 3Ton capacity hand operated over head Travelling (HOT) crane H- Typesuitablefor a spanupto6 Mtrs, andtravellengthupto10 Mtrs. with clear lift upto 6 M including gear type chain pulley block and geared Travelling trolley complete with all accessories including girder. 363 MOTORCONTROLCENTER(MCC)PANEL:-Singlefront,Indoor&floormounted,cubicaltypePanelfactory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shroudsandGlandPlate-3mmthick)CRCAsheetdulypower coated dustandverminproofIP-54/IS:2147,consideredEarth Bus-Bar-GI Strip compitable to SCADA operation with RS485 Port consisting ofINCOMMINGSECTION320 A, 50KA, TPN, MCCB microprocessor baseed (O/C,S/C) release-1No,SpreaderĮinks&ExtendedROHfor-1No,3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CĮ-1400A/5A,15VA - 3 Nos, Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA - 3 Nos, CT Shorting Terminal 4 Nos, Neutral Įink - 1 No.OUTGOINGSECTION100 A, 50KA, TPN, MCCBmicroprocessor based (O/C,S/C) REĮEASE - 4 No, Spreader Įinks & Extended ROH for MCCB - 4 Nos., 63A TPN MCCB 35KA- 3 Nos. Terminal 63A 364 Supply of Air Cooled Digital soft starter suitable for the ĮT motor offered for operationin AC three Phase 50Hz (+/- 5%), 415V(+/- 10%)includinglinecontactorssuitablefornextstandardhigher KWrating,Over&Underloadprotection,shortcircuit&single phasingprotectionwithfrequencymeter,Ammeter,Voltmeter, indicatinglamp6Nos,ĮEDON/OFFtypeandStart/Stoppush buttonandInstrumentFuses,suitabletoSCADAoperationwith RS485 Port of rating capacity 40HP/30KW 365 Supplyofmicroprocessorbasedthreephasesensingpower factor correction relay panel , IEC / EN 61000-6- (2&4) having 3 CT sensing,sensitivityupto50milliampsecondarycurrent,self analysingautoc/ksettingaccordingtotargetedpowerfactor setting, the relay shall have digit display unit for displayof real power factor, targeted power factor, lag/lead capacitor switching status, alarmoutput for under current, over current, insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like KW, KVA, KVAR rating capacity of 40KVAR 366 Supply & laying of 1.1 KV grade XĮPE insulatedun armoured multi strandcopperconductorcableof3C x 25 sq.mm fromcontrol PaneltorespectiveMotorswithlugsetc.(copperconductor should be electrlytic grade coppe, purity >99.97 % ISI markedas per IS:1554 P-I / IS:7098 P- I) 367 Supply &Fixing ofPowder coated GI Cable Tray 150mmx50mmx1.6mm 368 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick includingaccessories,andprovidingmasonryenclosurewith cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required according to latest IS:3043 369 Supplying and laying 50 mm X 6 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done byoverlappingandwith2 sets of brassnut bolt& spring washer spaced at 50mm) 370 Supply of ABC Dry Powder type Fire Extinguisher 4.5 kg conforming to IS: 15683:2006 371 Supply of Auto Phase reversal unit / Automatic switch with inbuilt the delay & enclosure (Confirms to IEC: 60947-1 & IEC: 60947-6-1) of 250Amp 372 S& F of all in one solar ĮED street light fixture with Integrated high efficientMonocrystallinepanel withĮithium(ĮiFePO4)Ferro Phosphate battery with BIS approved make .luminaire should be secondaryopticlensesforbetterdistributionwithdelivered efficacy of >100 Įumen per watt. Įuminaire can be supplied with Hybridswitchalongwithindicatortounderstandthesourceof power(eitherfromsolarorACsupply).shallhavecertificate tested fromMNRE approved Įab. Guarantee for total system is two years .Note: All the aboveshould be integrated and should be 1 system.make:Bajaj/Philips/Crompton.CompactSolar LED StreetLight-60W/12V/27AhwithGIpole 373 Internal&ExternalelectrificationofPumphouse 374 Twin tube light covered ĮED 20 Watt 375 450 mm dia exhaust fan 376 Providing & Fixing of IK07 IP-66 protected high power ĮED flood light system with Pressure diecast aluminium housing ĮM6/ ADC12 material 50 Watt Flood light 377 CompletewiringofPumphousewith1.5Sqmm&2.5Sqmm multistarnd copper conductor wire 1.1 KV with required 5A & 15A switches, ceiling rose 378 Supply of CE/UĮ Certified Surge protector for control panel 379 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 380 SupplyofAutomatic/SCADAoperatedelectromegnatic chlorination dozzer system 381 INSTRUMENTATIONWORK 382 Supply of CE/UĮ certified Full bore Electromagnetic Flow Meter of approved make of following dia and specifications complete: Media : Water (Raw/Chlorinated) , Pressure : up to 1.0 MPa,Processtemp:-50degC, Flow/MeterTube:SS304, Electrode:SSAISI316Į/ HastelloyC276/Tantalum,Įining Material : Hard Rubber/ Neoprene/Poly-urethane(PU) , Flange : SS /CS, Flange Standard & Rating : ANSI 150, Coil housing : SS AISI 304/CarbonSteel/ DieCast Aluminium,with anticorrosive paint & provide completelysealed(leakproof)constructionas perrequirement‘ofIEC 60529, Accuracy : + 0.5 % M.V.- velocity0.3 to 10 m/s, Transmitter/ signa convertorEnclosure: Die Cast Aluminium,Power Supply : 80-240V AC - 5OHz, Output 1 : 4-20 mA,Output2:Pulse,CommunicationOutput:RS485/Heart, Display Type : ĮCD/ ĮED Display, Cable Entry : M20 X 1.5, Provision of RAM/PROM to store calibrationandconfigurationparameters and totalizer value during power failure, Protection category- IP 68forsensor(flowtube)andIP67fortransmitter/convertor, including Surge Arrester, cable, of300mm dia size at common header 383 SupplyofCE/UĮCertifiedpressuretransmitterCEmarkdwith followingtechnicalparameters andInterfacingwithPĮCpanel including mounting arrangement.Output 4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDAccuracy - +/- 0.1 % of full scale or better Enclosure- IP 68 384 SupplyofCE/UĮcirtifiedofRadartypeleveltransmitterCE marked with following technical parameters and Interfacing with PĮC panel including mounting arrangement forCWROutput-4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68 385 SupplyofCE/UĮcirtifiedofRadartypeleveltransmitterCE marked with following technical parametersand Interfacing with PĮC panel including mounting arrangement with inbuild battery of 5 year life forOHTOutput-4-20 mA / HART Power supply - 24V DC ext. Display - 4 ĮEDRange- 0 to …30... mtrsAccuracy - +/- 0.25% of Full Scale or better Enclosure- IP 68 386 CE&UĮCertifiedPĮC/RTUinIP54enclosuresuitableto communicatewithintelligentGSMBasedmodemunitwithCPU and Power Supply with analog and Digital Parameter and features as specified for each for each ZPS/OHT to store and transmit data onGSMbackbone,RTUdesignedwithlogictotansferdataat multiple stations and also compatible for satellite communication alongwith control panel with IP 54 Protection , Industrial grade for all equipment and 24V and power supply 387 GSM/GPRSbasedwirelesscommunicationwith4Gmodemfor RTU/PĮC Capable to transfer and gather data from remote sites to controlstationsallaccessoriesincludedwithsignalenhancer, antennamadeforpumpingplant withSIMand rechargefor1 year 388 CE&UĮCertifiedPĮC/RTUinIP54enclosuresuitableto communicatewithintelligentGSMBasedmodemunitwithCPU and Power Supply with analog and Digital Parameter and features as specified for each for each ZPS/OHT to store and transmit data onGSMbackbone,RTUdesignedwithlogictotansferdataat multiple stations and also compatible for satellite communication alongwith control panel with IP 54 Protection , Industrial grade for all equipment and 24V and power supply for OHT due to Outside the campus 389 GSM/GPRSbasedwirelesscommunicationwith4Gmodemfor RTU/PĮC Capable to transfer and gather data from remote sites to controlstationsallaccessoriesincludedwithsignalenhancer, antennamadeforpumpingplant withSIMand rechargefor1 year 390 CE & UĮ Certified 7 HMI touch screen suitable to communication with PĮC/RTU for local display & control of process parameters 391 CE/UĮ Certified Intelligent energy meters 392 Completecablingforinstrumentation/SCADAequipmentswith power supply of panels form source for CWR & OHT 393 Security Survelliance IP Camera with all required accessories 394 Installation, testing and comissioning of pumping plant & associated all equipments as per approved drawing shall be done bybidderincludingchequerredplateandpaintingofpumping plant & main piping-valves. 395 Testing of Pumping Plant & Control Panel & valves etc at Manufacturer Works 396 11/0.44KVSUBSTATIONATCWRZONE-2 397 Supply of star rated Copper wound distribution Transformer ( All the distribution transformer must be star rated as per notification of(BEE)ministryofpower,GoverenmentofIndia)offollowing rating11/0.433KVDelta-StarConnected,VectorGroupDyn11, ONAN Cooled & as per BEE star level- 2 & BIS approved as per IS 2026-1977 & losses as defined as per IS 1180 part (I) 2014 including standardaccessorieslikeconservator,silicagel breather,Bucholzrelay,radiator,fins,HTcablebox&ĮTcable boxes, Off -ĮTC (+7.5% to - 15% @ 2.5%) temperature rise of 40 degree C in oil / 45 degree C in winding , ISI marked drain valve, DialtypeTemperaturegauge,OTI&WTI,marshallingbox,first filling of transformer oil as per IS :335-1953, Epoxy based paint.Ratingcapacity-160KVA(1w+1s) 398 Supplyof11KV,630 A,25kA/1Sec, VCBIndoortypepanelHT board, free standing motor operated & withdrawal type fabricated from 2 mm thick CRCA sheet steel , With Ammeter, Voltmeter, PF Meter, KWH Meter, MDI Meter, Selector Switches as required, CRT CT of required ratio (15VA ; Cl-1.0 / 0.5 ) PT (11 KV /110V/√3) , Fuses, IP42 Protection,4 / 8 /10 / 12-window Annunciation Panel , AC/ DC Control voltage 24/48/ 110/230V , ĮED Indication lamps , S/C, O/C&E/FProtection(IDMT)RelaysAlarm&tripcontactsfor Transformer protection(High oil temperature, Buchholz protection,highwindingtemperature,powerpack2x12V,etc completeinallrespectreadytouse(RTU),OEMMusthaveBIS certificate incuding 1no incoming & 2 no outgoing VCB 399 External batteryand batterycharger of suitablerating having 1 Hrs backup for H.T. Panel 400 Supply and laying of 11/12KV grade XĮPE H.T. cable as per IS:7098/ II/85,H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - (I)from UPPCĮmetering panel to H.T. Switch gear panel and panel to transformers 95Sq.mm.size 401 Supply of H.T. Cable end termination heat shrinkable type indoor joint kit 95sq.mm. 402 Supply of H.T. Cable end termination heat shrinkable type outdoor joint kit 95sq.mm. 403 Supply&layingofĮ.T.XĮPEinsulated armouredaluminium conductorcable of 1.1 KV grade Material :- H4- Grade aluminium conductorofpurity>99.6%&asperIS:1554P-I/IS:7098P- (I),conductorshallhaveelectrolyticaluminiumconfirmingtoIS 8130, IS 3975-1999.From transformer to Main ĮT panel of 3.5Cx 150Sq.mm. 404 Single front, Indoor & floor mounted,cubical type ĮT Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shroudsandGlandPlate-3mmthick)CRCAsheetdulypower coateddust andverminproofIP-54/IS:2147,consideredEarth Bus-Bar-GIStripcompitabletoSCADAoperationwithRS485 Port consisting ofINCOMMINGSECTION320A,50KA,TPN,MCCB microprocessorbaseed (O/C,S/C) release - 2 No , SpreaderĮinks & Extended ROH for - 2 No, 3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CĮ-1400A/5A,15VA - 3 Nos, Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA ABB - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Įink - 1 No.OUTGOINGSECTION320A,50KA,TPN,MCCB microprocessorbased(O/C,S/C) REĮEASE - 1 No, spreader Įinks & Extended ROH for MCCB - 1 Nos., 63A TPN MCCB 32KA- 2 Nos. Terminal 63A 405 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick includingaccessories,andprovidingmasonryenclosurewith cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required according to latest IS:3043 406 Supplying and laying 50 mm X 6 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlappingand with 2 sets of brass nut bolt & spring washer spaced at 50mm) 407 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS: 15683:2006 408 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 409 NOC from electrical safety department Govt. of UP 410 Fancing of substation in 2mtr height made from MS iron Jali & MS flat, angle iron andgrouting in propermannerincluding supply and laying of stone grit. 411 Internal&Externalelectrification 412 Twin tube light covered ĮED 20 Watt 413 450 mm dia exhaust fan 414 Providing & Fixing of IK07 IP-66 protected high power ĮED flood lightsystemwithPressurediecastaluminiumhousingĮM6/ ADC12 material 50 Watt Flood light 415 Complete wiring of HT and ĮT roomwith 1.5 Sqmm & 2.5 Sqmm multistarnd copper conductor wire 1.1 KV with required 5A & 15A switches, ceiling rose 416 S& F of all in one solar ĮED street light fixture with Integrated high efficient Monocrystalline panel with Įithium (ĮiFePO4) Ferro Phosphate battery with BIS approved make .luminaire should be secondaryopticlensesforbetterdistributionwithdelivered efficacy of >100 Įumen per watt. Įuminaire can be supplied with Hybridswitchalongwithindicatortounderstandthesource of power(eitherfromsolarorACsupply).shallhavecertificate testedfromMNREapprovedĮab.Guaranteefortotalsystemis two years .Note: All the above should be integrated and should be 1 system. make:Bajaj/ Philips / Crompton.Compact SolarLED StreetLight-60W/12V/27AhwithGIpole 417 Installation, testing and commissioning of 11 KV /.44 KV substations including H.T. panel and Į.T. panel including chequered plates, all labour T&P complete in all respect. 418 TestingofTransformer,HTandĮTPaneletcatManufacturer Works 419 11/0.44KVSUBSTATIONATCWRZONE-3 420 Supply of star rated Copper wound distribution Transformer ( All the distribution transformer must be star rated as per notification of(BEE)ministryofpower,GoverenmentofIndia)offollowing rating11/0.433KVDelta-StarConnected,VectorGroupDyn11, ONAN Cooled & as per BEE star level- 2 & BIS approved as per IS 2026-1977 & losses as defined as per IS 1180 part (I) 2014 including standardaccessorieslikeconservator,silicagel breather,Bucholzrelay,radiator,fins,HTcablebox&ĮTcable boxes, Off -ĮTC (+7.5% to - 15% @ 2.5%) temperature rise of 40 degree C in oil / 45 degree C in winding , ISI marked drain valve, DialtypeTemperaturegauge,OTI&WTI,marshallingbox,first filling of transformer oil as per IS :335-1953, Epoxy based paint.Ratingcapacity-160KVA(1w+1s) 421 Supplyof11KV,630 A,25kA/1Sec, VCBIndoortypepanelHT board, free standing motor operated & withdrawal type fabricated from 2 mm thick CRCA sheet steel , With Ammeter, Voltmeter, PF Meter, KWH Meter, MDI Meter, Selector Switches as required, CRT CT of required ratio (15VA ; Cl-1.0 / 0.5 ) PT (11 KV /110V/√3) , Fuses, IP42 Protection,4 / 8 /10 / 12-window Annunciation Panel , AC/ DC Control voltage 24/48/ 110/230V , ĮED Indication lamps , S/C, O/C&E/FProtection(IDMT)RelaysAlarm&tripcontactsfor Transformer protection(High oil temperature, Buchholz protection,highwindingtemperature,powerpack2x12V,etc completeinallrespectreadytouse(RTU),OEMMusthaveBIS certificate incuding 1no incoming & 2 no outgoing VCB 422 External batteryand batterycharger of suitablerating having 1 Hrs backup for H.T. Panel 423 Supply and laying of 11/12KV grade XĮPE H.T. cable as per IS:7098/ II/85,H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - (I)from UPPCĮmetering panel to H.T. Switch gear panel and panel to transformers 95Sq.mm.size 424 Supply of H.T. Cable end termination heat shrinkable type indoor joint kit 95sq.mm. 425 Supply of H.T. Cable end termination heat shrinkable type outdoor joint kit 95sq.mm. 426 Supply&layingofĮ.T.XĮPEinsulated armouredaluminium conductorcable of 1.1 KV grade Material :- H4- Grade aluminium conductorofpurity>99.6%&asperIS:1554P-I/IS:7098P- (I),conductorshallhaveelectrolyticaluminiumconfirmingtoIS 8130, IS 3975-1999.From transformer to Main ĮT panel of 3.5Cx 150Sq.mm. 427 Single front, Indoor & floor mounted,cubical type ĮT Panel factory fabricated (2 mm thick for sructure, 1.6mm thick for door,covers shroudsandGlandPlate-3mmthick)CRCAsheetdulypower coateddust andverminproofIP-54/IS:2147,consideredEarth Bus-Bar-GIStripcompitabletoSCADAoperationwithRS485 Port consisting ofINCOMMINGSECTION320A,50KA,TPN,MCCB microprocessorbaseed (O/C,S/C) release - 2 No , SpreaderĮinks & Extended ROH for - 2 No, 3 Phase Digital Multifunction Meter- 1 No, Digital Voltmeter 0-500V- 1 No, Digital Ammeter 0-400A- 1 Nos, CT For meter Resin Cast CĮ-1400A/5A,15VA - 3 Nos, Phase indication light ĮED type 220V AC - 1 Set, Control MCB SP 6A ,10KA ABB - 3 Nos, CT Shorting Terminal - 4 Nos, Neutral Įink - 1 No.OUTGOINGSECTION320A,50KA,TPN,MCCB microprocessorbased(O/C,S/C) REĮEASE - 1 No, spreader Įinks & Extended ROH for MCCB - 1 Nos., 63A TPN MCCB 32KA- 2 Nos. Terminal 63A 428 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick includingaccessories,andprovidingmasonryenclosurewith cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required according to latest IS:3043 429 Supplying and laying 50 mm X 6 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlappingand with 2 sets of brass nut bolt & spring washer spaced at 50mm) 430 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS: 15683:2006 431 Rubber mats for electrical purpose as per IS:5425-1969, plain/chequered (1mX2m) - 19mm thickness 432 NOC from electrical safety department Govt. of UP 433 Fancing of substation in 2mtr height made from MS iron Jali & MS flat, angle iron andgrouting in propermannerincluding supply and laying of stone grit. 434 Internal&Externalelectrification 435 Twin tube light covered ĮED 20 Watt 436 450 mm dia exhaust fan 437 Providing & Fixing of IK07 IP-66 protected high power ĮED flood lightsystemwithPressurediecastaluminiumhousingĮM6/ ADC12 material 50 Watt Flood light 438 Complete wiring of HT and ĮT roomwith 1.5 Sqmm & 2.5 Sqmm multistarnd copper conductor wire 1.1 KV with required 5A & 15A switches, ceiling rose 439 S& F of all in one solar ĮED street light fixture with Integrated high efficient Monocrystalline panel with Įithium (ĮiFePO4) Ferro Phosphate battery with BIS approved make .luminaire should be secondaryopticlensesforbetterdistributionwithdelivered efficacy of >100 Įumen per watt. Įuminaire can be supplied with Hybridswitchalongwithindicatortounderstandthesource of power(eitherfromsolarorACsupply).shallhavecertificate testedfromMNREapprovedĮab.Guaranteefortotalsystemis two years .Note: All the above should be integrated and should be 1 system. make:Bajaj/ Philips / Crompton.Compact SolarLED StreetLight-60W/12V/27AhwithGIpole 440 Installation, testing and commissioning of 11 KV /.44 KV substations including H.T. panel and Į.T. panel including chequered plates, all labour T&P complete in all respect. 441 TestingofTransformer,HTandĮTPaneletcatManufacturer Works 442 MASTERCONTROLSTATION(MCS) 443 CE/UĮ&BISCertifiedindustrialgradeĮEDMONITOR withlatest configuration as per specification 65 444 Video call media player of same OEM 445 Core i7 10th gen Desktop with 8 gb ram and 1 TB SSD 446 CE/UĮ Certified 3 KVA UPS with Batteries required for mentioned work wih 01 hrs backup 447 Full Development version of TAGS SCADA software with costomization ofsoftwareforMCSforunlimiteddigitalandanalogInput/output features as per requirements 448 CE/UĮ certified master control room PĮC with redundant CPU & power supply at MCS in IP-54 enclosure as per site requirement and specification required to complete in all respect 449 CE/UĮ certified Field gateway agent for transfering data for MCS/control room 450 GSM/GPRSbased wireless/Broadband/equivelent communication system for PĮC Capable to transfer and receive data & gather data from remotesitestocontrolstationsallaccessoriesincludedwithsignal enhancer, antenna along with running expences till 1 year 451 CE/UĮ certified Firewall for network protection 452 Surge protector for Ethernet communication protection 453 CE/UĮ Certified industrial grade Ethernet switch 454 Mobileappfacilitysystemarchitecture(industriesinternetbased& viewed through mobile apps for increasedblocal & remote visibility) 455 Canon/HP or equivalent Įaser Printer 1018 or equivalent. 456 Hp or equivalent multifunctioning Įaser Printer with scanner 457 BEE : 5 Star rating 1.5 Ton capacity air conditioner with voltage satbilizer 458 Office furniture ( office table - 2 No, revolving chair- 2No, Office chair-3 No, Godrej almirah - 1No) 459 Security Survelliance IP Camera with recorder 460 Supply and Fixing of fire extinguisher of 5 Kg. capacity conforming to IS: 15683:2006 461 Installation, Commissioning and testing of all above equipments for MCSwith all power cables 462 COST OF TRAIL & RUN FOR 3 MONTHS WITHOUT ELECTRICITY

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	04-01-2025	tender submission dates has been extended	Date	10-01-2025

INR 23600 /-

INR 4429000.0 /-

INR 44.28 Crore /-