Construction Of Gym Building With Gym Equipments In Rear Side Of Holy Cross School At Sathuvachari In Vellore District- 1 Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring, strutting, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10mts and initial lift of 2mts. and clearing and levelling the site, etc., complete complying with standard specifications. 2 Supplying and filling in foundation, basement, etc with filling Crushed Stone Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specifications and as directed by the departmental officers. 3 Supplying and filling of Well gravel by lorry in basement filling including stacking for premeasurement, conveyance loading and unloading charges and all other incidential charges and including filling laying watering and consolidating etc., complete as directed by the dept., Officers and complying with standard specification. 4 Cement Concrete 1:5:10 (One Cement, Five M-Sand and Ten aggregate) using 40 mm gauge hard broken granite stone jelly for Foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specifications. 5 Cement Concrete 1:5:10 (One cement, Five M-Sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying,consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. 6 Brick work in Cement Mortar 1:6 (One Cement and Six M-Sand) using best quality II class ground moulded chamber burnt bricks of size 9 x 4-3/8 x 2-3/4 including neat finishing, curing, etc., complete complying with standard specifictions. 7 For Foundation and Basement 8 For Superstructure in Ground floor 9 Supplying and erecting steel Shutteringincluding necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.50cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcations. (Payment for centering shall be given after the concrete is laid) 10 Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3mm for boarding laid over silver oak joists of size 10 cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10 cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaitons. (Payment for centering shall be given after the concrete is laid) 11 For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 12 For plane surfaces such as rectangular orSquare RCC columns, sunshades, top and bottom slab of RCC boxing etc. 13 Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.000 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.300 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.790 cum) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary and bearing surface of walls, beam shall be finished smooth with Cement mortar 1:3 (One Cement and Three M-Sand) and craft paper laid over it without claiming etc., complete complying with standard specifications and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials). 14 For Foundation and basement 15 For Superstructure in Ground floor 16 Supplying, fabricating and placing in position M.S. or R.T.S. reinforcements grill for RCC works as per the design given including cost of steel and black binding wire etc., complete complying with standard specifications. (The contractor will have to make his own arrangements for the supply of MS plain rod / RTS rod and black binding wire) 17 Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no M-Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specifications and as directed by the deparmental officers. 18 Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M-Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specifications and as directed by the departmental officers. 19 Plain Cement Concrete 1:2:4 (one cement, two M-Sand and four hard broken granite stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specifications and as directed by the departmental officers. 20 Supplying and fixing in position best approved of BIS quality of the 110mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of U clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 21 Manufacturing, supplying and fixing of Steel doors with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame.Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 G CR Sheets of best quality is laid as panel in the shutter frames.18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwitching the CR Sheet for rigidity.Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter.300mm length of hinges 2 Nos, for shtter is provided.6 Nos.of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. at the top provided 250x16mm size of Two aldrops are provided in single leaf door at lock rail section in the door for inner and outer provided and one rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear sideof the door at an appropriate place and 1 No. of M.S. handle of heavy duty. 22 A tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing.All members are given one coat of red oxide primer as directed by the departmental officers.The rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete. (Single Leaf). 23 Manufacturing, Supplying and fixing in position of steel windows with the following specifications.Outer frames of windows made of Z section F7D of size 33 x 25 x 3mm at 1.419 Kg/m and mullion J section (F4B) of size 46x25 x 3mm at 2.28 kg/m and shutter section of made of F7D of 33 x 25 x 3mm at 1.419 Kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance.The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames.Horizontal stiffeners using 18x5mm MS flat at 0.70 Kg/m at 3 Nos.for each shutter and additional diagonal stiffeners of the same MS Flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR sheets in position firmly4 numbers of sturdy hinges and Two number of handle-cum-latch of special type made with 18x5mm MS Flats are revetted to the shutters at an appropriate height in window Suitable opening is left for its easy operation.A stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. 24 Each window shutter having an adjustable stay made out of 18x5mm at 0.70 kg/m MS flat of length 320mm with three adjustable position.A matching peg is provided in the outer frame of the window at suitable place 4 Nos. of hold fasts of 120mm length spliced at the nds are welded to the out frame of the window by using MS flat of 18x5 mm at 0.70 kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter an MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge to edge between them.All members are painted with one cat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS7452/1990. The cost includes cost of all materials, labour charges and other incidental charges, etc., complete. 25 Two Leaves 26 Supplying and fixing of PVC vinyl flooring of ISI grade, 2mm thickness of approved shade after removing the existing damaged flooring composition, vinyl in nature. Durability: Excellent complying B.I.S standards, Fire resistance, should not support combustion, sound absorption :> 5db it should not be affected by petrol, alcohol, alkali, 5% acids & cooking oil, Fungi & bacteria resistance including labour charges etc complete. 27 Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M-Sand) 10mm thick including hacking the surfaces, providing cement mortar noising, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specifications and as directed by the departmental officers 28 Plastering with Cement Mortar 1:5 (One cement and Five M-Sand), 12mm thick in all floors including curing etc. complete complying with standard specifications and as directed by the departmental officers. 29 Painting two coats of newly plastered wall surface with ready mixed Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt and including necessary plaster of paris putty, wherever required etc., complete complying with standard specifications. (The colour and shade of the Emulsion paint shall be got approved by the Executive Engineer before use of work). 30 Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specifications. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) 31 Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) 32 Supply and fixing of single box type 436W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting 33 Supply and fixing of 1200mm (48) sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18) 34 Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch on suitable TW box 35 Supplying and Fixing of following GYM equipments in good conditions.The rate includes the cost of conveyance,loading unloading and erection as directed by the departmental officers etc, complete,complying with standard specification. 36 Fuctional trainer-SF021 37 Squat Machine 38 Legcur/leg Extension-SF012 39 Lat pupp Down/ Rowing Single Pulley - SF014 40 Pec/ Rear Delt - SF002 41 Adjustable Weight Bench - SF102 42 Adjustable Bench - SF102 43 Hexagon Dumbells Various Weights 44 Weight Plates Various Weights 45 Olmpic Rods - SF002 46 Interlocking mat 3 X 3 47 GST @ 18 %
