Tender for Due to change of occupation in type-6 house no. 7 situated in Lower Dalibagh colony, renovation of two Shatigrast bathrooms and kitchen, changing the face of Shatigrast windows/ doors, painting work of boundary wall of the house and any other necessary repair work - Dismantling tiles work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25mm. DAR 15.23.1 2 Providing and fixing on Wall Face Unplasticised Rigid PVC rain water Pipes conforming to IS:13592 Type A, including Jointing with Seal ring conforming to IS:5382, Leaving 10mm Gap for thermal expansion, all fittings like two nos bend, one mo Coupler or any other accessories and P/F PVC pipe clips fixed by means of 50X50X50mm hard wood plug, Secrewed with MS Screws of required lenght in wall face including cutting brick work and fixing in cement mortar 1:4 (i) Single Socketed pipes 110mm dia meter. 3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc 15 mm nominal outer dia pipes, (SDR-11) 4 Providing and laying rectified Glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours White, lovry GreyFume Red Brown laid on 20 mm thick cement mortar 1:4 (1 cement :4 Coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc complete. 11.39 5 Providing and fixing 1st quality ceramic, glazed wall tiles conforming to IS 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thck bed of cmeent mortar 1:3 ( 1 cement 3 coarse sand) and jointing with grey cmeent slurry @ 3.3 kg per sqm, including pointign in white cement mixed with pigment of matching shade complete. 8.31 6 Providing and fixing CIMBA Rimless One Piece with Seat Cover Size-660x340x720 mm. Cat No-S1013213 S Trap 300 mm Cera make, including Cutting and making good the walls and floors wherever required: 7 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter.18.22.1. 8 Providing and fixing C.P. brass long nose bib cock of approved quality confirming to IS standard and weighting npt less than 810 gms.15 mm nominal bore.18.50.1. 9 P/F C.P. brass Angle Valvefor basin mixture and geyser points ofapproved quality confirming to IS:8931.15 mm nominal bore.18.53.1. 10 Providing and fixing 600x450 mm bevelled edge mirror of superior glass of approved quality complete with 6 mm thickhard board groung fixed to wooden cleats with C.P. brass screws and washers complete.17.31 11 P/F Wash Basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern white vitrous china wash basin size 630x450 mm with a pair of 15 mm cp brass piller taps.17.7.1. 12 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia DAR 17.22b 13 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 13.88 14 Finishing wall with Premium Acrylic Smooth exterior Paint with Silicone Additives of required Shade New work. (Two or More Coats applied @1.43 ltr/10 sqm) Over and Including Priming Coat of Exterior Primer applied @ 2.20kg /10 sqm) (Apex Ultima, Weather Coat All guard asian, Berger. (Ch-15/DSR N0-13.47.1 ) 15 Structual Steel work riveted bolted or welded in built up section, trusses, Builds up gates,framed work lncluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Sl.N0-10.2, 16 Providing and fixing ISI marked 35 mm thick flush door Shutters Conforming to IS : 2202 (Part I)non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. DAR N0-9.21.1 17 Providing and fixing of 35, mm thick UP Teak Wood Jali Door and Window Shutter withheavy quality S.S. Jali with necessary beading, including supply and fixing of wooden cleats and stopper and including fixing and adjustment of hinges, bolts, locks handles, spring & or otherfitting but excluding their supply etc. Painting two Coats of Black Japan on All Frame fitting in necessary etc. Complete work as Per Direction of E/I. 18 Providing & fixing Float glass panes 5.00 mm thick glass panes (weigh not less than 12.50 kg/sqm)(DAR -9.7.7.2) 19 Supply and fixing of box type wardrobe with 19mm thick plyboard and shutter will be provided 25mm thick prelaminated board including supply of cost of all materials, labour T&P etc required for proper compleion of work. (Based on as per actual requirment) 20 Providing and Fixing of UV stabilised fibergalss reinforced plastic sheet roofin up to any pitch, including fixing with polymer coated J or L hooks, bolts & nuts 8 mm dia G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, Trusses etc the sheets shall be manufactured out of 2400 TEX Panel roving incorporating mininum 0.3% ultra-violet stabiliser in resing system under approximately 2400 PSL and hot cured. they shallbe of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and Is 12866 the sheets shall beopaque or translucent, clear or pigmented textured or smooth as specified. (5mm thick flat sheet 2.5 or 4.2 or 6) or step down (2 or 3 or 6) as specified. 21 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm .8.2.2.2. 22 Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 Note:- Structural design proof checked from a Government Engineering Institute, to be provided shall be paid separately. by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds Using R2 series with frame (70mm & above) x (40mm & above) & Glazed sash (25mm & above) x (50mm & above) with zinc alloy (zamak powder coated touch locks with hook (Height upto 1.2 metre).Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. As DSR -9.147.A4.1,
