|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (All kinds of soil) |
| 2 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering – All work upto plinth level.1:2:4(1 Cement: 2 fine Sand: 4 graded well brunt brick aggregate 20 mm nominal size) |
| 4 | 1:3:6 (1 Cement: 3 fine Sand: 6 graded well brunt brick aggregate 40 mm nominal size) |
| 5 | First class brick works in foundation and plinth including cost all materials as required complete :- (i) In cement mortar 1 :4 (1 Cement : 4 fine sand) |
| 6 | Centering shuttering including strutting, propping etc. and removal of form work for : a) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plan. |
| 7 | Reinforcement of R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level i) Thermo- Mechanically Treated bars of grade Fe- 500 D or more |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement i) 1:2:4 ( 1 Cement : 2 Fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 9 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials requiredas required complete :- In cement mortar 1 : 4 ( 1 cement : 4 fine sand) |
| 10 | First class brick work in superstructure in triangular, square and rectangular pillars above plinth level including cost of all materials as required complete :- i) In cement mortar 1 : 4 ( 1 cement : 4 fine sand) |
| 11 | Half brick masonry work with first class bricks in superstructure up to floor five level including cost of all materials as required complete :- i) In cement mortar 1:4 ( 1 cement : 4 fine sand) |
| 12 | Filling available excavated earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering lead up 50m and lift up to 1.5 m ( all kinds of soil) |
| 13 | Excavating, supplying and filling of local earth ( including royalty) by mechanical transport up to a lead of 5 Km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 14 | Providing corrugated GS sheet roofing including vertical/ curved surface fixed with Zink coated high quality Hex flanged self drilling screw ( size 12 x 55 mm) by drill machine but excluding cost of purlins, rafters and trusses in/c cutting to the size and shape wherever required complete as per direction of Engineer in- charge a) 0.63 mm GS sheet thick with Zink coating not less than 275 gm/ sqm. |
| 15 | Providing ridge or hips of width 45 cm ( Tata shakti/ Jindal) fixed with Zink coated high quality Hex flanged self drilling screw ( size 12 x 55 mm) by drill machine in/c. Washer complete as per direction of Engineer in charge a) 0.35 mm thick with Zink coating not less than 275 gm / sqm |
| 16 | Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete i) Hot finished welded type tubes. |
| 17 | Steel work welded in built up section/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required :- 1) In grating, frames, guard bar, railing, brackets, gates and similar works all complete . |
| 18 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to Is : 15622-2017 of approved make in all colours and shades laid over 20 mm thick cement mortar 1:4 ( 1 cement : 4 fine sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete. i) Soluble salt stain free vitrified tiles a) Size of tile 60x60 Cm |
| 19 | Providing and fixing 1st quality ceramic glazed wall tiles ( minimum 200 x 300 ) conforming to IS : 15622 -2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer in charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 20 | Providing and laying ceramic floor tiles in different sizes ( thickness to be specified by the manufacturer ) of 1st quality conforming to IS : 15622-2017 of approved make in colours such as White, Ivory, grey Fume Red Brown laid over 20 mm thick cement mortar 1:4 (1 Cement : 4 Fine Sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete Anti Skid Tiles i) Ceramic Tiles 1st quality 300 x300 mm in all shades and designs. |
| 21 | Providing and fixing PVC false ceiling providing SPUF 142- D-01 (different design 10 mm thick 150 mm width and necessary length) approved colour concealed type panelled carrier T section ( EWUF 106 : 40x63.5 mm and L section ( EWUF 405:40x68 mm) with necessary screws, hold first wooden beading and Ms pipe structured 48 mm dia @ 1200 mm c/c including cutting holes and making good walls etc complete as per direction of Engineer In charge. |
| 22 | 12 mm cement plaster of mix 1) in cement mortar 1 : 4 ( 1 cement : 4 fine sand) |
| 23 | 12 mm cement plaster of mix 1) in cement mortar 1 : 4 ( 1 cement : 4 fine sand) in/c Neat cement punning |
| 24 | 15 mm cement plaster on the rough side of single or half brick wall of mix 1) In cement mortar 1 : 4( 1 Cement : 4 fine sand) |
| 25 | Providing and fixing white vitreous china pedestal type water closet ( European type W.C Pan) with seat and Lid, 10 litre low level white PVC flushing cistern with manually controlled device ( handle lever), conforming to IS : 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 1) W.C Pan with ISI marked white solid plastic seat and lid |
| 26 | Providing and fixing on wall face unplasticised Rigid PVBC rain water, soil waste & vent pipes ( working pressure 4 kg/ cm 2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion : a) Single socketed pipe – 110 mm OD |
| 27 | Providing and fixing on wall face unplasticised PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansioni)Bend 87.5 degreea) 110 mm |
| 28 | ii) Single equal tee with door a) 110 x 110 x110 mm |
| 29 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm weighing not less than 190 gms |
| 30 | 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59 x24 mm and wall thickness 2mm =0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of MS galvanised / plastic brackets of size 75 x220 mm having wall thickness 1.0 mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M\S tube of size 20 x20 mm and 1 mm = 0.1 mm wall thickness. The lock rail made up of H section, a UPVC hollow section of size 100 x 24 mm and 2 mm + - 0.2 mm wall thickness fixed to the shutter styles by means of plastic/ galvanised MS U cleats. The shutter frame filled with a UPVC multi chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm + - 0.1mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanised Ms rod and sustained with nuts and washers, complete as per manufacturers specifications and direction of Engineer In charge ( for W.C and bathroom door shutters). |
| 31 | Providing and fixing Chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with claims at 1.00 m spacing. This includes jointing of pipes and fittings with one steps CPVC solvent cement testing of joints complete as per direction of Engineer In Charge. Internal work- exposed on wall. i) 25 mm nominal outer dia. Pipes |
| 32 | ii) 15 mm nominal outer dia. Pipes |
| 33 | Providing and fixing brass bib cock of approved quality a) 15 mm nominal bore |
| 34 | Providing and fixing brass stop cock of approved quality 1) 15 mm nominal bore |
| 35 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade ( Payment shall be made after submission of Taste Certificate issued by the Manufacturers ). New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 36 | Finishing walls with acrylics smooth exterior paints of required shade of approved brand and manufacture ( Payment shall be made after submission of Taste Certificate issued by the Manufacturers ). New work (two or more coats applied @ 1.67 ltrs / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade ( Payment shall be made after submission of Taste Certificate issued by the Manufacturers ). a) Two or more coats on new work. |
| 38 | Providing & fitting fixing of C.P brass hand spray (royal made) as per direction of the Engineer In-charge. |
| 39 | Providing of fitting fixing of C.P brass Twin one stop cock ( Royal Made) complete as per direction the Engineer In-Charge |
| 40 | Providing and fixing C.P brass shower rose with 15 or 20 mm inlet a) 100 mm dia meter |
| 41 | Providing and fixing ball valve ( brass) of approved quality high or low pressure with plastic floats complete. a) 25 mm nominal bore |
| 42 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colours weighting not less than 80 gms |
| 43 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings a) Flat back wash basin of size 550 x 400 mm |
| 44 | Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing i) Rectangular shape 453 x 357 mm |
| 45 | Providing and fixing aluminium works for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with – fasteners of required dia and size including necessary filling up of gaps at junctionsi.e. at top and bottom and side with required EPDM rubber/ neoprene gaskets etc. Aluminium Sections shall be smooth, rust free, straight, mitred and joint mechanically whenever required including cleat angel, aluminium snap bedding glazing/ panelling, C.P brass / stainless steel screws, all complete as per architectural drawing and direction of the Engineer In- Charge. ( Glazing and panelling and dash fasteners to be paid for separately) A) for fixed portion of approved quality :- i) Anodized Aluminium ( Anodized transparent or dyed to required shade according to IS 1868, minimum anodic coating of grade AC 15) |
| 46 | Providing and fixing aluminium works for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with – fasteners of required dia and size including necessary filling up of gaps at junctionsi.e. at top and bottom and side with required EPDM rubber/ neoprene gaskets etc. Aluminium Sections shall be smooth, rust free, straight, mitred and joint mechanically whenever required including cleat angel, aluminium snap bedding glazing/ panelling, C.P brass / stainless steel screws, all complete as per architectural drawing and direction of the Engineer In- Charge. ( Glazing and panelling and dash fasteners to be paid for separately) A) for fixed portion of approved quality :- i) Anodized Aluminium ( Anodized transparent or dyed to required shade according to IS 1868, minimum anodic coating of grade AC 15) |
| 47 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilators, shutters, partition etc. with EPDM rubber /neoprene gasket etc. complete as per architectural drawing and the direction of Engineer In-charge ( Cost of snap beading shall be paid in basic items) :- A) With float glass panes of 4.0 mm thickness (weight not less than 10.0 kg/ per sqm) |
| 48 | Construction soak pit 1.20 x 1.20 x1.20 M filled with brickbats including s.w. drain pipe 100 mm dia meter and 1.20 m long complete as per standard design |
