Tender For Special Repair To Bldg. No. P-04 (Or Living) Of E Arty Regt At Bikaner Mil Stn; 1 Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for in this Schedule, complete all as specified & as directed.Note : Contractor shall make arrangement to protect tiles, plumbing items, sanitary fittings, etc under the slab, etc by gunny bags with sand or any other suitable arrangement and quoted rates shall deemed to include this aspect. 2 Demolition of unreinforced cement concrete of any description and in any position (not otherwise specifically provided for in this Schedule, complete all as specified & as directed. 3 Demolition of lime concrete of any description and in any position (not otherwise specifically provided for in this Schedule, complete all as specified & as directed. 4 Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. 5 Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed. 6 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed. 7 Dismantling of stone slabs and tiles of any description or any thickness in floors, aprons etc, laid bedded and pointed in any mortar, complete all as specified & as directed. 8 Dismantling of brick tiles or terracing tiles single layer on roofs, complete all as specified and as directed.Note : Tiles shall be dismantled carefully and stacked properly including segregating the serviceable & unserviceable tiles as directed. Serviceable tiles shall be reused under the respective item of this Schedule. 9 Taking down shutters (including fittings & fixtures) of any description not exc 1.0 sqm each, complete all as specified and as directed. 10 Taking down shutters (including fittings & fixtures) of any description exc 1 Sqm and not exc. 2 Sqm each, complete all as specified and as directed. 11 Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts or dismantling brick work (holes cur and any other damage to jambs, wall) and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. 12 Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts or dismantling brick work (holes cur and any other damage to jambs, wall) and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. 13 Taking down old rusted & damaged steel windows/ventilators including guard bars / grill of size exe 1.50 sqm including cutting holes for hold fasts & making good the disturbed portioncomplete all as specified & as directed. 14 Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. 15 Returning, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed. 16 Removing excavated soil/material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified and as directed. 17 M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. 18 M&L for PCC 1:3:6type C0 (using 12.5mm graded crushed stone aggregate) as in filling up chowkat/frame hollows and similar workscomplete all as specified and as directed. 19 M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and as directed. 20 M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in plinth courses, string courses, lacing courses, parapets, copings, kneelers, apex stones, bed plates, roof kerbs, mud stops and the like including weathering, slightly rounded, chamfered angle and throating as directed including useand waste of form work (straightor curved) all exposed surface of concrete finished fair complete all as specified & as directed. 21 M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like complete all as specified & as directed.Note :- Reinforcement & formwork shall be measured and paid for separately. 22 M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and the like complete all as specified & as directed.Note :- Reinforcement & formwork shall be measured and paid for separately. 23 Supply only liquid water proofing compound (ISI marked) complete all as specified and directed. 24 M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed. 25 M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed.Note : Brick work under this item shall be carried out in sewage disposal work (i.e. manholes) and area drainage work (i.e. drains). 26 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified & as directed. 27 Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified & as directed. 28 Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide for rough finished flat surfaces of concrete complete all as specified & as directed. 29 Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles,fixed to chowkat, complete all as specified & as directed. 30 Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24(a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & as directed. 31 S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube, fixing in opening as per specifications complete all as specified and as directed. 32 S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed.. 33 S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed. 34 S&F butt hinges of size 100mm stainless steel ISI marked complete all as specified and as directed. 35 Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type C-21 anodised complete all as specified and directed. 36 S&F 100 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified. 37 S&F 150 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified and as directed. 38 S&F 100mm size Extruded aluminium handle, fabricated type, anodised, complete all as specified & as directed. 39 S&F mild steel pressed handle, 150 mm size, oval type, stove enameled black ISI Marked complete all as specified and as directed. 40 S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & as directed. 41 S&F stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed. 42 S&F 250 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and as directed. 43 Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 44 Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed as in repair complete all as specified and as directed. 45 S&F mild steel framed work as in doors, gates, steel frames, chowkats, hold fast etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position including dismantling structural steel complete all as specified and as directed. 46 M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. 47 M&L for mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. 48 All as per serial item No. 47.00 here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binderscomplete all as specified. 49 S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. 50 S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. 51 S&F factory fabricated pressed steel frame/box windows, ventilators with glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed.Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items.Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3). 52 S&F factory fabricated pressed steel frame/box windows, ventilators without glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed.Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items.Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3). 53 M&L for preparing surface and cleaning of concrete slab by brushes and applying evenly one coat of of industrial bituminous 85/25 @ 1.20 litre/sqm and provide a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps. 54 M&L for Lime concrete terracing as specified in roof complete all as specified & as directed.Note : For lime concrete, mudia kankar (Source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES Schedule Part-I shall be used. 55 M&L for 40mm thick brick tiles, joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, laid on roof over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed. 56 All as per serial item No. 55.00 here-in-before but except brick tiles complete all as specified & as directed. 57 M&L for 75mm thick PCC (1:3:6) type C2 using 40mm graded crushed stone aggregate as in laid in panels, surface finished even and smooth without using extra cement complete all as specified and directed. 58 M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, leveling course, etc, surface finished fair and even, complete all as specified and as directed. 59 M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. 60 M&L for machine cut Kota stone slab 20 to 25mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. 61 M&L for grinding and bee wax polishing on marble/ granite/ Kota stone/ stone work whereever required to give high gloss finish complete all as specified & as directed. 62 M&L for Non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. 63 M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed. 64 M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed. 65 M&L for 10mm thick rendering in cement and mortar 1:3 in sunken portion, mixed with liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified.Note : Supply only integral liquid water proofing compound shall be measured and paid for separately. 66 M&L for removal of loose concrete and cleaning the surfaces and filling the cracks with Polymer modified mortar using Dr Fixit Pidicrete URP or other equivalent product as approved by GE and thereafter applying two coats of Dr Fixit Bathseal WPC or other equivalent product as approved by GE in Sunken areas complete all as per manufacturer’s instructions, specified & directed.Note : Where contractor desire to use equivalent product of Dr Fixit Pidicrete URP and Dr Fixit Bathseal WPC, he shall submit the technical literature of equivalent products to establish the equivalency of products to the entire satisfaction of GE and both products shall be of same manufacturer as approved by the GE. 67 M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed. 68 M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed. 69 M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified. 70 M&L for preparation of newly plastered / unplastered surfaces of walls & applying two coats of white wash complete all as specified and as directed. 71 M&L for preparation of old surfaces (plastered or unplastered) of walls including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed. 72 M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and as directed. 73 M&L for preparation of old surfaces (plastered or unplastered) of ceilings including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed. 74 M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 3mm thick white wall care putty complete all as specified & as directed. 75 M&L for preparation of old surfaces by complete removal of existing treatment of paintedwalls including pillar etc by mechanical equipment like electric wall sander and applyingtwo coats of oil bound distemper by using of approved shade/tint complete all as specified and directed. 76 M&L for preparation of new plastered surfaces and applying white wall care putty for filling the undulations as required and finished with two coats of Exterior emulsion paint/ weather proof exterior grade paint of first quality by using of approved shade/tint over a coat of primer including sealing the cracks all as specified in manufacturers instruction Make : STP Ltd / Asian Paint (Apex Ultima) / Berger Paint (Weather coat long) complete all as specified and directed. 77 M&L for preparation of old surfaces by complete removal of existing treatment of paintedwalls including pillar etc by mechanical equipment like electric wall sander and applyingtwo coats of Exterior emulsion paint/ weather proof exterior grade paint of first quality by using of approved shade/tint over a coat of primer including sealing the cracks all as specified in manufacturers instruction Make : STP Ltd / Asian Paint (Apex Ultima) / Berger Paint (Weather coat long) complete all as specified and directed. 78 M&L for Cupboard knob mild steel 40mm dia complete all as specified and as directed. 79 M&L for welding in repairs not 2.5cm in length and not exc 6mm thick of metal complete all as specified and as directed. 80 M&L for running welding in repairs with thickness of metal not exc 6mm including provision for stopper of peg stay steel handle fitting complete all as specified and as directed. 81 M&L for welding in repairs not 2.5cm in length and not exc 6mm thick of metal complete all as specified and as directed. 82 Hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed. 83 Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified. 84 S&F in repair 5mm thick looking mirror of selected quality with and including stainless steel spacers any size as approved by GE complete all as specified and as directed. 85 M&L for preparation of new surfaces of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed. 86 M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed. 87 M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamelpaint of approved tint over a coat of zinc chrome primer complete all as specified & as directed. 88 M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 89 Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 15mm bore complete all as specified and as directed. 90 M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed. 91 Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 15mm bore obtained serviceable vide serial item No. 89.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed.Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used. 92 Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 20mm bore complete all as specified and as directed. 93 M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed. 94 Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 20mm bore obtained serviceable vide serial item No. 92.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed.Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used. 95 Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.Note : (i) The water storage tanks shall be 2 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water.(ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I.(iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item. 96 S&F in repairs Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed in repair complete all as specified and as directed. 97 S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed in repair complete all as specified and as directed. 98 S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, complete all as specified and as directed. 99 S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, Jet spray (brass chromium plated of butterfly shape) with 1.00m PTMT tube suitable for 15 mm bore GI pipe with PTMT nut & nipple, complete all as specified & as directed. 100 S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed. 101 S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, including CP pillar tap heavy duty with PVC connetion and including 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed. 102 S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed. 103 S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed.Make : Cat Part No. ‘G4902A1’ of ‘Parryware’ / Cat Part No. ‘F2002101’ of ‘Cera’ / Cat Part No. ‘CQT-23011B’ of ‘Jaquar’ / Cat Part No. ‘9202’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after. 104 S&F in repairs 15 mm bore bib tap, brass, chromium plated, long body, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, including CP brass wall flange, complete all as specified & as directed. Make : Cat Part No. ‘G4906A1’ of ‘Parryware’ / Cat Part No. ‘F2002152’ of ‘Cera’ / Cat Part No. ‘CQT-23047’ of ‘Jaquar’ / Cat Part No. ‘9208’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after. 105 S&F in repairs 15mm bore Angle stop valve, brass, chromium plated, fancy type, screwed down, high pressure with capstan head, screwed both ends for iron pipe or for union, including CP brass wall flange, complete all as specified & as directed.Make : Cat Part No. ‘G4907A1’ of ‘Parryware’ / Cat Part No. ‘F2002201’ of ‘Cera’ / Cat Part No. CON-059KN’ of ‘Jaquar’ / Cat Part No. ‘9210’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after. 106 S&F in repair 20mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. 107 S&F in repairs brass shower rose, round type, brass, chromium plated, Fancy type, 125mm dia (minimum) with 200mm long (minimum) shower arm or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed.Make : Cat Part No. ‘T9809A1’ of ‘Parryware’ / Cat Part No. ‘F7010212AB’ of ‘Cera’ / Cat Part No. ‘BOS-87’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after. 108 S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, fixed complete all as specified and as directed. 109 Supply and fixing 100mm bore cast iron, Spun Pipes, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed. 110 Supply and fixing 75mm bore cast iron, Spun Pipes, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed. 111 Supply and fixing 100mm bore cast iron, Spun Pipes, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed. 112 Supply and fixing 75mm bore cast iron, Spun Pipe, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed. 113 M&L for extra over cast iron pipe & fitting 100mm bore providing lead joints in lieu of cement joints complete all as specified and as directed. 114 M&L for extra over cast iron pipe & fitting 75mm bore providing lead joints in lieu of cement joints complete all as specified and as directed. 115 S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 100mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete allas specified & as directed. 116 S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete allas specified & as directed. 117 S&F 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed. 118 S&F 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed. 119 S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed. 120 S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed. 121 S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified & as directed. 122 S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified & as directed. 123 S&F 100mm bore cast iron TEE (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed. 124 Supply and fixing cast iron bends (any radius) with ducks foot or heel rest complete all as specified. 125 Supply and fixing cast iron vent cowl for 100mm bore complete all as specified. 126 S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed. 127 S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed. 128 Supply and fixing 110mm bore PVC (SWR) bends any radius with rubber ring joints / solvent cement joints complete all as specified. 129 Supply and fixing 75mm bore PVC (SWR) bends any radius with rubber ring joints / solvent cement joints complete all as specified. 130 S&F 110mm bore PVC (SWR) Single junction (Single T ) equal or unequal with rubber ring joints / solvent cement joints complete all as specified and directed. 131 S&F 75mm bore PVC (SWR) Single junction (Single T ) equal or unequal with rubber ring joints / solvent cement joints complete all as specified and directed. 132 S&F cast iron floor trap 100mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) including taking out old unserviceable trap complete all as specified and directed. 133 S&F PVC (SWR) Gully trap 125/110mm setting and jointing with solvent cement complete all as specified and directed. 134 S&F in repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, fixed in floor, complete all as specified and as directed. 135 M&L for salt glazed stone ware gully trap square or round mouthed type P of size 150 x 150mm with CI grating, setting & jointing with cement with grouting surrounding gully trap with PCC 1:3:6, type C1block 30x30x45cm together with necessary form work, excavation & earth work in soft/loose soil, complete all as specified and as directed. 136 S&F salt glazed stone ware drain pipes of 150mm bore, Class ‘SP 2’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested including dismantling old drain pipe complete all as specified and directed.Note :- Excavation & earthwork shall be measured and paid separately. 137 M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150mm bore pipe complete all as specified and as directed. 138 M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. including placing in position and set in CM (1:4) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule. 139 S&F in repairs PVC 32mm/40mm dia waste pipe fitting brass chromium plated for wash hand basin/ sink, complete all as specified and as directed. 140 S&F in repairs Grating 100mm dia PVC with and without hole having minimum weight 75gms complete all as specified and as directed. 141 Structural design for Roof Slab, Beams, Chajja and other connected RCC members required to be re-constructed under this Schedule with & including vetting of structural design from approved Govt Engineering College/NITTTR/CBRI, complete all as specified and as directed. Notes : (i) Tenderer shall carryout the site visit to ascertain the size of slab, other RCC members, arrangement of rooms, etc required for design purpose. (ii) Four sets of Structural drawings shall be provided to GE by the contractor duly vetted as above. 142 Taking down carefully existing unserviceable/perished surface conduit/concealed conduit/ batten/ casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators, wooden boxes, MS sunken boxes, etc and making good the disturbed surfaces of wall, floors, ceiling, etc to match with the adjoining surfaces, complete all as specified and as directed. 143 M&L for Modular point wiring for one light /fan /bell /buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/ drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etcall as per IS, terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular switches, sockets, regulators etc with and including modular cover plates with frame of requisite module, complete all as specified and as directed.Notes : (i) Cost of cutting/leaving forming chases for conduits, sinking for modular metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed to include for modular metal flush boxes of requisite module and modular cover plates with frame of requisite module of colour as approved by GE. 144 All as per serial item No. 143.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed. 145 All as per serial item No. 143.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed. 146 All as per serial item No. 143.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed. 147 All as per serial item No. 143.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed. 148 S&F Modular type switch 1 way 6 Amp, 1 module, single pole, 230 volts complete all as specified and as directed. 149 S&F Modular type switch 1 way 16 Amp, 1 module, single pole, 230 volts complete all as specified and as directed. 150 S&F Modular Socket, 6A - 2/3 pin combined 2 module, 230 volts complete all as specified and as directed. 151 S&F Modular Socket 6A/16A - 2/3 pin combined 2 module, 230 volts complete all as specified and as directed. 152 S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed. 153 S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed. 154 S&F Modular type, Fan step regulator, 120 Watt - 2 module, electronic socket type five step controlled 230 volts complete all as specified and as directed. 155 S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 230 Volt, 10 kA, ‘C’ Curve, ISI marked, fixed in repairs, complete all as specified and as directed. 156 S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 Watt 240 Volt, 50 Hz AC, ISI Marked decorative type with driver holder and LED lamp,correlated colour temperature shall be minimum 6500 degree Kelvin, including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.Make: Model “LDL-10-WW” of M/S Crompton/ Wipro Cat Part No. LL20-111-XXX-65NE3/ Cat Part No. ENDURALINEARNEOBS10WLED865SPCWH of Havells/or equivalent in makes mentioned in Appendix B here-in-after. 157 Taking down of serviceable and refixing after LED tube light fitting, 1x20 Watt, 230 Volts, basic all purpose surface and wall mounted LED batten type with driver & polycarbonate housing including tube rod and all accessories, prewired and connecting up with & including 3 core sheathed flexible copper cable 1.5 sqmm of suitable length upto light point/ceiling rose, complete all as specified and as directed. 158 S&F LED tube light fitting, 1x20 Watt, 230 Volts, basic all purpose surface and wall mounted LED batten type with driver & polycarbonate housing including tube rod and all accessories, prewired and connecting up with & including 3 core sheathed flexible copper cable 1.5 sqmm of suitable length upto light point/ceiling rose, complete all as specified and as directed.Make : Philips, Cat Part No. LED 20S PSU CW GR S2/ Crompton Greaves, Cat Part No. LDDR20-CDL Dazzle Ray/ Bajaj, Cat Part No. BCLAB 20W or equivalent make here-in-after in appendix B 159 S&F bulk head energy efficient LED light fitting, 1x10 Watt, 230 Volts, surface mounted, comprising of high brightness LEDs, IP-65 protection, with & including all standard accessories, prewired and connecting up with & including 3 core sheathed flexible copper cable 1.5 sqmm of suitable length upto light point/ceiling rose, complete all as specified and as directed. Make : Havells Cat Part No. RUGBYNEONFT10WLED860SSYM TOPC or equivalent in makes mentioned in Appendix ‘B’ here-in-after. 160 Supply, installation, commissioning & testing Light Emitting Diode (LED) based street light fitting, 35 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 2500 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA/polycarbonate/toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multistranded copper conductor cable of 1100 Volt grade (ISI marked), including taking down old unserviceable light fittings complete all as specified and as directed. 161 NOTES FOR LED LIGHT FITTINGS :(i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13.(ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80.(iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :-(a) Manufacturing defects.(b) Failure due to mechanical and electrical impact.(c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries. 162 Supply and fixing mounting bracket (suitable for fixing/holding street/security light fittings) made of 40mm bore GI pipe ‘light grade’ not less than 1.50m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, matching with section of Pole/suitable for wall, including taking down old bracket complete all as specified and as directed. 163 S&F sheet metal enclosure for distribution boards flushed in wall, double door type, 415 Volts with 200 Amps rated bus bar, load line DB fitted with bus bar neutral links blank plates, VTPN, 4 way, suitable for MCBs, fitted complete all as specified and as directed including taking down old existing unserviceable DB with fixtures of any type & capacity.Note : Cost of cutting/leaving forming chases for sinking for DBand making good in CM 1:4 shall deemed to be included in quoted rate of this item. 164 S&F sheet metal enclosure for distribution boards flushed in wall, double door type, suitable for fixing MCBs, 415 Volts with 200 Amps rated bus bar, SPN, 8 way, suitable for MCBs, fitted with and accessories, complete all as specified and as directed.Note : Cost of cutting/leaving forming chases for sinking for DBand making good in CM 1:4 shall deemed to be included in quoted rate of this item. 165 S&F MCB, 6 to 32 Amps, Single Pole, 240 Volts, 10 kA, ‘C’ Curve, with over load and short circuit protection, fixed in repair complete all as specified and as directed. 166 S&F MCB, 6 to 32 Amps, SPN, 240 Volts, 10 kA, ‘C’ Curve,with over load and short circuit protection, fixed as in repair complete all as specified and as directed. 167 S&F MCCB 4 Pole 100 Amps, thermal magnetic having, breaking capacity 16 KA, 415 Volt, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed. 168 Supply & fixing Exhaust fan of 450mm sweep made of steel body, heavy duty, double ball bearing, copper wound, steel body, 1200 RPM, Single Phase 230 Volt, 50 Hz AC supply complete with blades, frame and louver shutter and connecting up with & including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn into & including flexible PVC conduit and fixed by using 4 Nos, 100mm long 8mm dia bolt nuts and washers and grouted in wall in CM (1:3) including taking down old exhaust fan and deposited to store yard AGE E/M complete all as specified & as directed. 169 M&L for carefully disconnecting electric & water connections and taking down existing serviceable Geyser (water storage type) of capacity 25/50 litre vertical type and re-fixing the same with & including ‘Anchor’ type /fastener type bolts & nuts (Set of 4 bolts of suitable size but not less than 10mm dia 125mm long with nuts &washers) into the wall grouted properly to hold the geyser and making good the disturbed surface as original and re-connecting electric & water connections, complete all as directed. 170 Taking down fan, sealing cable end, dismantling blades and removing fan and blades & refixing ceiling fan of any make, any sweep, keeping side to store in safe custody for painting of ceiling fans complete, insitu with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified and directed. 171 M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre,charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing.Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. 172 M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI markedcables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling complete including dismantling & taking down old unserviceable sub main wiring complete all as specified.Notes :-(i) 02 runs of 6 sqmm size main cable, 01 run of 6 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item. 173 M&L for sub main wiring with Four runs of 10 sqmm (nominal area) size main cable & two run of 10 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI markedcables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 32mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling complete including dismantling & taking down old unserviceable sub main wiring complete all as specified.Notes :-(i) 04 runs of 10 sqmm size main cable, 02 run of 10 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item. 174 Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core (ISI marked) laid in trenches/ ducts, through pipe, under floors or roads/along poles etc including taking down old unserviceable cable complete all as specified and as directed.Note :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. 175 M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground electric cable complete all as specified and as directed.Notes :-(i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used.(ii) For the purpose of payment, only punned thickness shall be measured. 176 Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm confirming to IS -5820 complete all as specified and as directed. 177 M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 20mm bore, complete all as specified and directed.Note :-Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule. 178 M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 25mm bore, complete all as specified and directed.Note :-Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule. 179 M&L for galvanized steel water tubing medium grade of 40mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 40mm bore, complete all as specified and directed.Note :-Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule. 180 M&L for galvanized steel water tubing medium grade of 50mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 50mm bore, complete all as specified and directed.Note :-Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule. 181 S&F in repair 25mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. 182 S&F in repair 40mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. 183 S&F in repair 50mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. 184 M&L for cutting existing steel tubing for 20mm to 50mm bore in position for alteration to required length for insertion of new branch, tee, collar, tail pieces, etc complete all as specified and directed.Note:- Excavation & earth work and fittings required for job shall deemed to be included in the rate quoted for this item. 185 M&L for Valve Pit of internal size 90cm x 90cm x 60cm built in brick masonry complete all as specified in Particular Specifications and as shown on drawing No. BTD-811 Sheet No. 1/2 & 2/2. 186 M&L for Galvanized iron tubing, 80mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable including taking down old unserviceable GI pipe complete all as specified and directed.Note :- Excavation & earthwork shall be measured & paid for separately.
