Tender For Construction Of Workshop Building At Iiser Pune, pune-Maharashtra

Tender For Construction Of Workshop Building At Iiser Pune; 2 Earthwork 3 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains including dressing of sides and ramming of bottoms, all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of Soil. 4 Carriage of material by mechanical Transport including loading, unloading and stacking up to 1.00 KM 5 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains including dressing of sides and ramming of bottoms, all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of Rocks. 6 Filling available earth in IISER Campus in trenches, plinths, sides of foundations, etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 M., and for all lifts. Rate including excavating from the location in campus by mechanical means, loading, carriage up to 1.00 KM, unloading in the plinth, etc complete. 7 Filling available excavated earth (Excluding rock) in trenches, plinths, sides of foundation, etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 M., 8 Supply and filling Dry/trap/granite/quartzite / genesis rubble Stone soling size 200-300mm height Including hand-packing and compacting with approved earth 230 mm thick complete for Plinth soling (including royalty) by mechanical transport and lead including ramming and watering of the earth.( for all lead & and lift.) 9 Providing and laying in position ready mixed cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources,Portland Pozzolana/Ordinary Portland /Portland Slag cement,admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength;including pumping of concrete to site of laying, curing,carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in the design mix shall be payable separately. In case the cement content in the design mix is more than 110% of the minimum specified cement content, the contractor shall have the discretion to either re-design the mix or bear the cost of extra cement. Concrete of M15 grade with a minimum cement content of 240 kg /cumAll works upto plinth level : 10 Brickwork with non-modular fly ash bricks (Confirming to I.S.12894) Class designation 10 average compressive strength inplinth level.Cememt Mrotar 1:4 (1 Cement: 4 Coarse Sand) 11 Making plinth protection 50mm thick of cement concrete 1 : 2: 4 (Grade M15) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth. 12 Providing and laying in position ready mixed cement concrete for reinforced cement concrete work;usingcoarse aggregate and fine aggregate derived from natural sources,Portland Pozzolana / Ordinary Portland /Portland Slagcement,admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability andworkabilitywithout impairing strength; including pumping of concrete to site of laying, curing,carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge;for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M30 grade withminimum cementcontent of 350 kg /cum. All work upto plinth level. 13 Providing and laying in position ready mixed cement concrete for reinforced cement concrete work;usingcoarse aggregate and fine aggregate derived from natural sources,Portland Pozzolana / Ordinary Portland /Portland Slagcement,admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability andworkabilitywithout impairing strength; including pumping of concrete to site of laying, curing,carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge;for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M30 grade withminimum cementcontent of 350 kg /cum.All work above Plinth level 14 FORMWORK 15 Centering and shuttering including strutting,propping etc. and removal of form work etc. Foundation footings bases for columns 16 Centering and shuttering including strutting,propping etc. and removal of form work etc Lintels, beams,plinth beams, girders,bressummers and cantilever. 17 Centering and shuttering including strutting,propping etc. and removal of form work etc. Column, piers,abutment,pillars, post and strut 18 Centering and shuttering including strutting,propping etc. and removal of form work etc .Suspended floors, roofs, landings, balconies and access platform 19 Steel Reinforcement 20 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo- mechanically treated bars of grade FE-500 D/FE-550 D or more up to& above Plinth level at any height. 21 Pre Engineerered Structure :Design, Engineering, drawing, fabrication, supply, and erection of a Pre-Engineered steel building with a rigid frame for a clear span of width 30.00 Mtr. outer/outer of walls, and length 48.03 M outer/outer having a bay spacing of 1 @ 5.80 M. c/c and sloping roof and a clear height 8.50 m at the center and 6.00 m. at sloping end.as per drawing and technical specifications.Note: All the measurements to be followed as per drawing & no price deviation on account of the same.The primary members shall be 345 Mpa grade made up of steel plates of minimum thickness 6mm . Secondary members for purlin ,girts etc shall be 345 Mpa and cold formed GI section of 120gsm.All primary members like column,rafter shall be painting with 2 coats of epoxy paint finish of approved shade including a coat of primer at factory itself. The total thickness of painting shall be 125 nicrons ( 25 micron of primer and 2 coats of 50 micron epoxy finish ) Anchor bolts shall be Electro galvanised of 4.6 grade and connection bolts shall be 8.8 grade HSFG.The Rate shall also include for the following.i) Mezzanine Structure including, Staircase and Deck sheets as shown in the drawings.The thiskness of deck sheet shall be 0.8 mm thick of 345 grade .ii) All canopies and Chajjas as shown in the drawings.iii) Supplying, pouring and packing non-shrink grout as per manufacturers specifications under base plates of columns, as per drawing and specifications with all leads and lift at all levels including cost ofpacking plates. iv) Supply fabrication, erection, and installation of Single length 0.50 mm color coated Standing Seam Flex - Lok Profile Double Structural Architectural Insulated Zip Standing Seam Steel Roofing System including all Chajjas as shown in the drawing.Necessary accessories such as clips, fasteners, and sealants shall be provided for a complete roofing system. The grade of sheet shall be 550 mpa.The insulation shall be rock wool insulation of50mm thick having density of 48kg/m3 , insulation shalll be placed over the weld mesh frame of size 75x75x 4mm thick with aluminium foil .v) Turbo Ventilators of 24 Dia. 8 No.s(Qty)fitted with nylon-made typhonic bearing, double top cap ensured permanent alignment in inverted cap design. Corrugated foil framed vanes give rigidity strength, airflow, and protection against weather change.Roller bearing system with Sealed ball bearings for smooth operation and longevity, housing upper and lower bearings, drives out dust soil grit, and forging material and retains complete lubrication in the unit.Constructed from high-grade aluminum alloy for durability and corrosion resistance. Translucent opel base which allows 20 % to 25 % natural daylight inside the building including necessary waterproofing to seal turbo ventilator edges with roof sheet. (Guarantee of 10 years for water proofing to be submitted.)vi) Providing and fixing precoated galvanized steel sheet roofing with accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with a total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/self-tapping screws complete in Vertical Wall Cladding :vii.a) Ridges plain:600 mm. to match with roofing sheet.vii.b.) Gutter & Down Take Pipe: To be designed as per the rain fall intensity To match with Roofing Sheet and cladding not less than 150 mm Dia. For Circular Pipes or 150 mm X 150 mm for rectangular pipes. viii) Providing and fixing 2 mm thick polycarbonate sheet of Opal white in colurincluding jointing accessories of required shape and shade with Light Transparancy not less than 30 %. including all fixures complete of approved make as per the direction of the Engineer- in charge.The description of items in BOQ shall be read along with Drawings and Technical specifications. The rate quoted in the BOQ by tenderers is deemed to have included all aspects covered in the Technical specifications unless stated otherwise. All features and details shown in Tender / Good for Construction Drawings are deemed to have been included in the Rates quote for corresponding items in the BOQ. NOTE- Successful tenderers are requested to submit the detailed design loading and supporting documents and the shop drawings approved by third party i.e. recognized institutes like IIT, COEP, VJTI, and VNIT. However, the work shall be carried out only on prior approval of the Engineer-in-charge after necessary checking and approval of design concepts and detailed shop drawings by Third party.Work Order will be issued on approval of design by Third party only.In case agency fails to submit Third party approval within a month after the issue of Letter of Acceptance then the offer will be cancelled & work order will not be issued & EMD will be forefitted. Mode of Measurement: The Plinth Area of the building i.e. outer measurements of the buildings will be considered for payment purposes. 22 Civil works 23 Providing & Fixing low density Plastic sheet having 200 micron thickness with overlap 450mm wide joints on compacted earth surface before concerteing work. 24 Providing and laying R.C.C. pavement of mix M-30 with ready-mixed concrete from the batching plant. The ready mixed concrete shall be laid and finished with a screed board vibrator, vacuum dewatering process, and finally finished by floating, brooming with a wire brush, etc. complete as per specifications and directions of the Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). Also the quoted rate inclusive single mat reinforcement steel for flooring by 8mm dia bars at 150 C/c both ways binding with 18g wires. 25 Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150mm to 300 mm thickwith Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3)in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 26 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and lightweight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level, etc. complete. 27 Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. 28 Providing and fixing steel chicken mesh of average aperture 10 mm, wire dia 0.50 mm and fixing withnails on wall surface of 30cm width at junction of brick masonary and RCC surface as required before plastering etc. complete as per direction of engineer in charge. 29 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 30 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. Size of tiles 600 x 600mm in flooring Make: Somany/ Johnson/ Kajaria / RAK. 31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Make:Somany/ Johnson/ Kajaria / RAK. 32 Providing and laying antiskidCeramicfloor tiles of size 600 x 600 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.Make: Somany/ Johnson/ Kajaria / RAK. 33 Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-molded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias, and similar locations of required size, approved shade, color and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch-ups, including rubbing, curing, molding and polishing of edges to give high gloss finish etc. complete at all levels. Area of slab upto 0.50 sqm: Granite stone slab of color black,cheeey/rubby red 34 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 35 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 36 Applying priming coats with a primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter 37 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. TWO Coats 38 Finishing walls with Premium exterior paint up to 10 meters building with Silicone addictives over masonry/ RCC wall of required shade with Two or more coats applied @ 1.43 ltr/10sqm over and including primer applied @ 2.20/10 sqm) or as per manufacturers specifications. 1. Preparing the surface for further painting activity etc. complete including cleaning etc complete. Quoted rate shall be including working at any height by using swing or suitable arrangement to reach inaccessible location etc complete.2. One coats of primer shall be applied as per OEM specifications.3. Two coats of painting shall be done as per approved pattern and shade. Quoted rate shall be including cost of all lifts, scaffolding, hanging platform, making surface ready for application of external paint etc complete. Quoted rate shall be including transportation, lead, lift, scaffolding etc complete. Nothing extra shall be paid separately. 39 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete. On Structural steel work not for PEB Steel. 40 Providing and applying 3 mm thick epoxy self-smoothening flooring on concrete surface having moisture content less than5 %. Carry out surface preparation including grinding of concrete surface, proper cleaning, removing of loose mortar, paint residuals, curing compound residues, repairing of floor cracks and dents using epoxy putty, application of FloArm Primer 1290 -epoxy penetrating primer for concrete surface, using brush or roller, allow to become tacky depending upon temperature, mixing and application of FloArmPES 2 – 2mm thick, self levelling epoxy screed followed by mixing & application of FloArmTop SL1 ST – 1mm thick ,Flow applied epoxy resin based floor topping using slow speed drill andpoured prepared screed surface atcoverage – 3 sqm/5 kg Pack for 1 mm DFT. Now level the material using serrated trowel and roll the same with spiked nylon roller to remove slight trowel marks and entrapped air from the materialetc. complete including all tools and tackles as per manufacturer& specification. The work is to be executed directly on concrete surface so proper levelling of surface has to be ensured by the contractor. If required, required levlling shall be done by agency without any extra cost. 41 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Kiln Seasoned and chemically treated hollock wood 42 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). 43 Providing and fixing factory made laminated veneer lumber glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick float glass panes for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, all as per directions of Engineer-in-charge (Note:- Butt hinges and necessary screws shall be paid separately)35 mm thick shutters 44 Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick(weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 45 Providing and fixing door closer DCR - 6003H (concelead) , EN size3 ,silver 65kgs ,latching speep adjustable make Yale /equivalent 46 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 47 Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. 48 Provising and fixing Providing in position (as per 1868/1882) Aluminum Sliding Windows of three tracks with rectangular pipe 95 x 38.10 x 0.90 m mat weight 0.637 kilogram/one running meter. With windows frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kilogram/one running meter. Top and side track section 91 x 31.75 x 1.30 mm at weight 0.933 kilogram/running meter. the shutter should of bearing bottom 40 x 18 1.25 mm at a weight of 0.417 kilogram/one running metre. Interlocking section 40 x 18 1.10 mm at weight 0.469 kilogram / running meter and handle and top section 40 x 18 x 1.25 mm at weight 0.417 kilogram/ running meter. as per detailed drawing and as directed by Engineer-In-Charge with all necessary aluminum sections fixtures and fastening such as roller bearing in nylon casting and self-locking catch fitted In vertical section of shutter including 5 mm thick plain glass and aluminum mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete with color anodizing.Note: Sample of one Aluminium Sliding Window in all respect to be approved by E.I.C. 49 Providing & Fixing in position Aluminium Ventilators for Toilets with Aluminium Anodised Frame & frosted glass 3 mm. thick in Louvers etc complete with Color Anodizing.Note: Sample of one Aluminium Ventilator in all respects to be approved by E.I.C. 50 Supplying and fixing Rolling Shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover 80x1.25 mm M.S. laths with 1.25 mm thick top cover of required thickness for rolling shutters.Note: Shop Drawing to be approved by E.I.C. 51 Providing and fixing ball bearing for rolling shutters. 52 Extra for Electrical motorizeddevices chain and cranked operation for operatingrolling shutters : exceeding Exceeding 16.80 sqm in area 53 Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). 54 Door For Machine Room: 2.40 M X 2.40 M. as specified below.i) Frame: The door frame shall be a single rivet grooved profile of size 152 mm X 55 mm made out of a minimum 1.2 mm (18 gauge) thick galvanized steel sheet. Frames shall be metered & field assembled with self-tabs. Frames to have an inbuilt grooved sealing system & shall be site fitted with PVC seal as standard. All provisions will be mortised, drilled & tapped for receiving appropriate hardware. The frame should be provided with back plate brackets & anchor fasteners for installations on a finished plastered masonry wall opening. frames shall be fitted with non-fire-rated puffs & gaps shall be filled with backer rod & silicone sealant.ii) Shutter:door leaf shall be 46 mm thick fully flushed double skin door with or without vision lite. The door leaf shall be manufactured from a minimum 0.8 mm (22 Gauge) thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be a resin-bonded honeycomb core. all doors shall be factory prepped for receiving appropriate hardware & providing with necessary reinforcement for hinges, locks & door closers. the edges should be interlocked with a bending radius of 1.4 mm. For a pair of doors integrated astragals have to be provided on the meeting site for both active & inactive leaves. vision lite wherever applicable should be provided as per manufacturers recommendation with a clip-on arrangement. (iv) Finish:all doors & frames shall be finished pure polyster powder coated & shall have passed a minimum of 500 hours of salt spray test.Make Shakti / Horman / Avian / Equivalent. (v) Door for Machine Room as specified above in detail with 2.4 M. X 2.4 M. size. 55 Providing and fixing to frames 30mm thick fibre glass reinforced plastic (FRP) Panelled /extruded profiled door shutter of approved color, brand and manufacured, made with fire -retartdent grade unsaturated polyster resin,moulded to 3 mm thick FRP laminate for forming hollow rails and styles with granite frame ,cast monolithicallyu with 5mm thick FRP laminate fopr panels confirmorming to IS 14856-2000 etc complete as directed. 56 Providing & Fixing 12 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process on existing metal frameto be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, joint finisher and two coats of primer suitable for board as per manufactures specification and direction of engineer in charge all complete. 57 Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufactures specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. 58 Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufactures specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:Birdnet material: High density polyethylene,Hole type: hexagonal,diamond,square,raschelknitted square, Mesh size 15mm/16mm width upto 6.2m color -black,green,white and blue 59 Public Health Engineering 60 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :300 mm dia. R.C.C. pipe 61 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x60 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 62 Supplying, fixing and testing of 6kg PVC pipes confirming to IS 4985. and fittings (avialable fittings in market and fabriacted fittings ) such as tee, elbow, y , coupler, etc.for Soil and Waste pipe works in toilets,etc. Pipes chasing in wall, running in Sunken floors and suspendend in ceiling level for ewc, wash basin,floor trap etc. Using solvent cement joints for jointing the pipes with fittings. Work includes chasing in wall, making required size holes in brick walls, etc., and re do same with water proofing components to the entire satisfaction of site engineer.etc complete. 150mm dia 63 Supply and installation of Foamcore uPVC pipes suitable drain and waste system for underground and above ground applications. Pipe shall be compliant to ISI 16098:1 .Pipe shall be Light weight & strong , Longer service life , Chemical and corrosion resistance , Non-toxic , Non-conductor type. Foamcore pipes shall be multilayer having outer and inner layers of conventional PVC and middle layer of foamed PVC. Outer and inner layers are designed to take the load while the middle layer of foamed PVC gives rigidity while maintaining the shape of the pipe under load. The socket shall have groove inside for rubber ring. The rubber ring to ensures trouble free water tight joint with allowance to thermal expansion /contraction. One end of the pipe shall be plain and other end shall be self-socketed with an integral groove to hold the rubber gasket. Pipes shall be joined with OEM approved solvent cement. Quoted rate shall be working below ground and above ground , earth work activates shall be measured separately. For above ground applications bidder shall consider clamping of pipe with wall with GI clamps at every one meter including cost of clamp and nails. Quoted rate shall be including cost of sockets , tees, Y bend , reducer , GST , Labour, Lead ,wastage, Lift, transportation, make holes in brick work and finishing etc complete. Nothing extra shall be paid separately. Pipe laying shall be done as per Instructions of Engineer In-charge including removal of old unserviceable pipes and stacking pipes to Scrap Yard within campus. Nothing extra shall be paid separately. Actual length of pipe commissioned at site shall be measured for the payments. Pipe of 160mm dia Approved Makes : Prince / Supreme / Finolex / Astral 160 mm nominal dia Pipes 64 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes 65 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 66 Providing and fixing Wash Basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:Make:Hindware/ Parryware/Cera/ JaquarWhite Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 67 Providing and fixing white vitreous china extended wall mounted water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush-fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.Make :Hindware/ Parryware/Cera/ Jaquar 68 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 69 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore 70 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Make: Hindware/ Parryware/Cera/ JaquarSingle half stall urinal with 5 litre P.V.C. automatic flushing cistern 71 Supply and fixing UPVC/PVC floor trap with cockroach trap and CP grating 150 mm nominal size square 100 mm diameter of inner hinged round grating various inlet from 40 to 110 mm diameter and varius outlet from 75 to 100 dai. With extension pipe ,tee connection ,fixed in sunken floor complete. 72 Providing and fixing toilet paper holder : C.P. brass 73 Supply and fixing CP double coat hook fixing with necessary screws etc. complete. 74 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high, and 112 mm distance from wall of standard shape with a bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 75 Supplying Stacking and spreading 6 mm. thick red Bajri / grit over watered & rolled ground. Including of the preparation of the surface/.With Road roller / hand roller 76 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing of size Rectangular shape 1500x450 mmeach1817.20 77 Providing & laying Non-Pressure NP 3 Class (Medium Duty) RCC Pipes including collars/spigot jointed with a stiff mixture of cement mortar in the proportion of 1:2 (1 Cement: 2 Fine Sand) including testing of joints, etc. complete.150 mm dia. R.C.C. pipe 78 Electrical works 79 Supplying, Transportation ,installation, testing & commissioning loading & unloadingof cubical type LT panel suitable for 415V, 3 phase, 4 wire 50 Hz AC supply system. Panel shall be fabricated in compartment form from CRCA sheet steel of 2mm thick for frame work & covers, 3mm thick for gland plates including cleaning & finishing complete withtank process for powder coating having thickness of minimum 80 micrometersin approved shade,The panel shall be as per IS 8623 specicications & having valid CPRI Test Certification 4000Amp,50KA for 1sec. refre Following Details &SLD Drawing No:- IISER/CRN/EMEA/WB/EL/SLD-01Tender specifications data sheet. Refer special conditions On pg no.299For details of specifications of above said panels. PANEL REFERENCE :SUB PCC MENDELEEV PANEL ( Refer Following Details &SLD Drawing No:- IISER/CRN/EMEA/WB/EL/SLD-01Tender specifications data sheet.a) IncomingSection as under :(a.1) IncomersMCCB:- 800A, 4P, 35 KA Moulded Case Circuit Breaker (MCCB)with inbuilt Microprocessor release (LSIG ) over load , short circuit, instantenous, Ground Fault: 1 Number(a.2) Control MCB 6A , Class-C as shown on SLD: (a.3) Indications : LED Indication : RYB forPhase &ON/OFF/TRIP indication lamp for MCCBStatus with required control MCB as shown on SLD - For each incomer(a.4)Analouge Volmeter96x96 mm 0-500 Volts With 7 Position Selector Switch: 1 set (a.5) Meters: Microprocessor based Digital Load manager for : KW .KWH,KVA, KVAR,KVARH, Hz, Volts,Amp, p.f. TDH, & MD KVA with RS 485 Serial communication port duly wired for rady to use.(a.6) Resin Cast Current Transformers :3 Nos. 800 / 5 A ,15 VA CL:1 CT’s for Metering : for incomer b) Outgoings feeders as unde rb.1 )Type of Feeders : TPN Moulded Case Circuit Breaker (MCCB) InbuiltAdjustable Microprocessor Over current, Short circuit ,Instantinious, and Earth faultrelease (LSIG) Rating ofOutgoings feeders:b.2) 03Nos 400 Amp 35KA TPN MCCBb.3) 01Nos 150 Amp 35KA TPN MCCB b.4) 01Nos 63 Amp 35KA TPN MCCB b4 : Indications :LED ON/OFF/TRIP Indication for eachoutgoings b.2 : Meters:3 Phase 4 Wiresconnected Multifunction meters for KWH and Amp with RS 485 serial Comminication Port duly wired and ready to use for each outgoing feeder. b.3: Resin Cast Current Transformers : 1 Set of3 Nos CTs with15 VA CL:1 ,400/ 5 Amp , 150/ 5A , 63/5A Secondary Current CT’s for Rrespective Amp rating of each outgoings feeders forMeteringe ) Busbars as under e.1) Main Horizontal Busbar :800A 4P Aluminum 35 K.A. 1-Sec , busbar at current density of0.8 Amp /Sq.mm for each bus sectione.2) Vertical TPNBusbar :Amp rating of Vertical TPNBusbar shall be Sum of total connected Feederat current density of0.8 Amp /Sq.mm 80 Supplying, Transportation ,installation, testing & commissioning loading & unloadingof cubical type LT panel suitable for 415V, 3 phase, 4 wire 50 Hz AC supply system. Panel shall be fabricated in compartment form from CRCA sheet steel of 2mm thick for frame work & covers, 3mm thick for gland plates including cleaning & finishing complete withtank process for powder coating having thickness of minimum 80 micrometersin approved shade,The panel shall be as per IS 8623 specicications & having valid CPRI Test Certification 4000Amp,50KA for 1sec. refre Following Details &SLD Drawing No:- IISER/CRN/EMEA/WB/EL/SLD-01Tender specifications data sheet. Refer special conditionOn pg no. 299For details of specifications of above said panels. PANEL REFERENCE :WORK SHOP PDBPANEL -01 Refer Following Details &SLD Drawing No:- IISER/CRN/EMEA/WB/EL/SLD-02Tender specifications data sheet.a) IncomingSection as under :(a.1) IncomersMCCB:- 400A, 4P, 35 KA Moulded Case Circuit Breaker (MCCB)with inbuilt Microprocessor release (LSIG ) over load , short circuit, instantenous, Ground Fault: 1 Number(a.2) Control MCB 6A , Class-C as shown on SLD: (a.3) Indications : LED Indication : RYB forPhase &ON/OFF/TRIP indication lamp for MCCBStatus with required control MCB as shown on SLD - For each incomer(a.4)Analouge Volmeter96x96 mm 0-500 Volts With 7 Position Selector Switch: 1 set (a.5) Meters: Microprocessor based Digital Load manager for : KW .KWH,KVA, KVAR,KVARH, Hz, Volts,Amp, p.f. TDH, & MD KVA with RS 485 Serial communication port duly wired for rady to use(a.6) Resin Cast Current Transformers :3 Nos. 400 / 5 A ,15 VA CL:1 CT’s for Metering : for incomerb) Outgoings feeders as under b.1 )Type of Feeders : TPN Moulded Case Circuit Breaker (MCCB) InbuiltAdjustable Microprocessor Over current, Short circuit ,Instantinious, and Earth faultrelease (LSIG) Rating ofOutgoings feeders:b.2) 06Nos 125 Amp 35KA TPN MCCB b.3)09Nos 63Amp 35KA TPN MCCBb4 : Indications :LED ON/OFF/TRIP Indication for eachoutgoings b.2 : Meters:3 Phase 4 Wiresconnected Multifunction meters for KWH and Amp with RS 485 serial Comminication Port duly wired and ready to use for each outgoing feeder.b.3: Resin Cast Current Transformers : 1 Set of3 Nos CTs with15 VA CL:1 ,125/ 5 Amp, 63 / 5 Amp Secondary Current CT’s for each outgoings feeders forMetering e ) Busbars as under e.1) Main Horizontal Busbar :400A 4P Aluminum 35 K.A. 1-Sec , busbar at current density of0.8 Amp /Sq.mm for each bus sectione.2) Vertical TPNBusbar :Amp rating of Vertical TPNBusbar shall be Sum of total connected Feederat current density of0.8 Amp /Sq.mm 81 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm 82 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 185 sq. mm and upto 400 sq. mm 83 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 35 sq. mm and upto 95 sq. mm 84 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 95 sq. mm and upto 185 sq. mm 85 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 185 sq. mm and upto 400 sq. mm 86 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle) 87 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 25/40x3mm MS flat clamp) 88 Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. 89 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required.3½ X 25 sq. mm (28mm) 90 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required. 3½ X 50 sq. mm (35mm) 91 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required. 3½ X 70 sq. mm (38mm) 92 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required. 3½ X 150 sq. mm (50mm) 93 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required.3½ X 300 sq. mm (70mm) 94 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 400 sq. mm (82mm) 95 Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required.4 X 16 sq. mm (28mm) 96 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type )3 1/2 x 400 sq.mm ALuminium ,XLPE Armourd Cable 97 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type )3 1/2 x 300 sq.mm ALuminium ,XLPE Armourd Cable 98 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type ) 3 1/2 x 150 sq.mm ALuminium ,XLPE Armourd Cable 99 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type ) 3 1/2 x 70 sq.mm ALuminium ,XLPE Armourd Cable 100 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type ) 3 1/2 x 50 sq.mm ALuminium ,XLPE Armourd Cable 101 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type ) 3 1/2 x 25 sq.mm ALuminium ,XLPE Armourd Cable 102 M.V. ALCable supply : Supply, loading, transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT powercablesas per IS 7098(Part 1) of following sizes.( Note :- Cable shall be consideredFlat armoured type )4 X 16 sq. mmALuminium ,XLPE Armourd Cable 103 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type ) 4X6 sq.mmCopper ,XLPE Armourd Cable 104 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )4X4 sq.mm Copper ,XLPE Armourd Cable 105 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )4X2.5 sq.mm Copper ,XLPE Armourd Cable 106 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )3X2.5 sq.mm Copper ,XLPE Armourd Cable 107 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )1 xCore x25 Sq.mm CopperFlexible FLRS Cables 108 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )1 xCore x16 Sq.mm Copper Flexible FLRS (Green Outersheath) 109 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type ) 12X2.5 sq.mmArm Copper Control cable 110 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type )4C X 2.5Sq.mm.CU-Armoured PVC Insulated Flexibale Multicore 111 M.V. Cu Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade XLPEinsulated over all FRLS outersheathed, Copper conductor, armoured LT powercables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be consideredFlat armoured type ) 3C X 2.5Sq.mm.Shielded Copper eanlded -Armoured cable 112 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 4x 6Sq.mm Copper ,XLPE Armourd Cable 113 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 4x 4Sq.mm Copper ,XLPE Armourd Cable 114 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 4x 2.5Sq.mm Copper ,XLPE Armourd Cable 115 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 3X2.5 sq.mm Copper ,XLPE Armourd Cable 116 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 1 xCore x25 Sq.mm Cu FlexibleUnarmouredFLRS 117 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 1 xCore x16 Sq.mm Cu FlexibleUnarmouredFLRS(Green Outersheath) 118 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 12X2.5 sq.mmArm Copper Control cable 119 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 4C X 2.5Sq.mm.CU-Armoured PVC Insulated Flexibale Multicore 120 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 3C X 2.5Sq.mm.Shielded Copper eanlded -Armoured cable 121 End termination of Cu cable : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copperlugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required 3C X 2.5Sq.mm.Copper Flexible cable 122 M.V Straight Throught Joint :Supplying and making straight through joint with cast resin compound including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required3.5 x70 sq.mm 123 M.V Straight Throught Joint :Supplying and making straight through joint with cast resin compound including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required3 1/2 x 150 sq.mm 124 M.V Straight Throught Joint :Supplying and making straight through joint with cast resin compound including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required3 1/2 x 400 sq.mm 125 Cu Flexible Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade PVCinsulated over all FRLS outersheathed, Copper conductor,LT powercables of as per of following sizes.3C X 2.5Sq.mm.PVC CopperFlexibleUnarmouredcable 126 Cu Flexible Cable supply : Supply, loading ,transportation unloadingat site, storages at site ,shifting from storage place to site, of1100 Volts grade PVCinsulated over all FRLS outersheathed, Copper conductor,LT powercables of as per of following sizes. 1C X 4 Sq.mm.PVC CopperFlexibleUnarmouredcable 127 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 128 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required. Details of cost for one Set 129 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 130 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. 131 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. 132 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 133 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. 134 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 135 Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required. It includes provding insulating support on maximum distance of 1.0 meter 136 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 137 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required. 138 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required. 139 Providing and fixing earth bus of 50 mm X 5 mm G.Istrip on surface for connections etc. as required.( 300mm Long with 8mm Nut bolts of 10 Nos) 140 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 141 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet orsurface of wall for lightning conductor complete as required.(For horizontal run) 142 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 143 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness 144 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness 145 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness 146 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness 147 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray bends (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness 148 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray bends (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness 149 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray bends (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness 150 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray Tee (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness 151 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray Tee (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness 152 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray Tee (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm width X 50 mm depth X 2.0 mm thickness 153 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group A 154 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group B 155 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group C 156 Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 157 Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 158 Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 159 Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 160 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm 161 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25 mm 162 Supply & fixing following modular switch/ Socket on the exisitng modular plate & switch box including connection but excluding modular plate etc. as required5/6 amps switch(For Power socket) 163 Supply & fixing following modular switch/ Socket on the exisitng modular plate & switch box including connection but excluding modular plate etc. as required 15/16 amp switch(For Power socket) 164 Supply & fixing following modular switch/ Socket on the exisitng modular plate & switch box including connection but excluding modular plate etc. as required 3 pin 5/6 amp socket outlet (For Power socket) 165 Supply & fixing following modular switch/ Socket on the exisitng modular plate & switch box including connection but excluding modular plate etc. as required 6 pin 15/16 amp socket outlet (For Power socket) 166 Supply and fixing modular blanking plateon the exisitng modular plate &switch box with matching colour including connection but excluding modular plate etcas required. 167 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.1 or 2 Modulebox (75mmx75 mm)(For Power socket/ELV Purpose) 168 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.3 Modulebox(100mmx75 mm)(For Power socket/ELV Purpose) 169 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.4 Modulebox(125mmx75 mm)(For Power socket/ELV Purpose) 170 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.6 Modulebox(200mmx75 mm)(For Power socket/ELV Purpose) 171 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.8 Modulebox(125mmx125 mm) (For Power socket/ELV Purpose) 172 Supply & fixing following size/modules,GI box alongwith modular base and cover plate for modular switches in recess etc as required.12 Modulebox(200mmx150 mm)(For Power socket/ELV Purpose) 173 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required.1 or 2 Module (For Power socket/ELV Purpose) 174 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required. 3 Module (For Power socket/ELV Purpose) 175 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required. 4 Module (For Power socket/ ELV Purpose) 176 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required. 6 Module (For Power socket/ ELV Purpose) 177 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required. 8 Module (For Power socket/ ELV Purpose) 178 Supply & fixing following modular base and cover plate for modularswitches in recess etc as required. 12 Module (For Power socket/ELV Purpose) 179 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). 180 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 181 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. 182 Supplying and fixing brass batten/Angle holder including connection etc.as required 183 Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick steel conduit, aluminium cast back plate and brass holder complete, including wiring the down rod with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and painting etc. as required. 184 Providing and fixing 16/0.20mm (0.50sqmm) twin flat flexible,FR PVC insulated, copper cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required. 185 Installation, testing and commissioning of pre-wired,fluorescent fitting/ compact fluorescent fitting of all types, with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc as required. 186 Supply, installtion ,testing, loading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge.150 to 160 W, IP rating not less thanIP-65/IK08 LED HIGHBAY LUMINARIES , BEAM ANGLE=NARROW BEAM, CCT=CW(5700K), LUMEN OUTPUT not less than 22500 Lumens, size min 400mm dia, Mounting should be done on mainframe of building structure including all necessary arragement for safe installation. 187 Supply, installtion ,testingloading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 30 to 40 W, IP rating not less than IP-20,RECESS / SURFACE MOUNTED SQUARE (600X600mm)+/- 10mm,LUMINARYEQUI. TO CCT=CW(6500K),LUMEN OUTPUT not less than 3500 Lumens 188 Supply, installtion ,testingloading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 30 to 50 W, Batten fitting, IP rating not less than IP-65,LED SURFACE MOUNTED WEATHERPROOF LUMINARY EQUI. TO CCT=CW(6500K),LUMEN OUTPUT not less than 4000 Lumens 189 Supply, installtion ,testingloading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 18 to 24 W, batten fitting, IP rating not less than IP-20,LED SURFACE MOUNTED LUMINARIES, CCT=6500K, LUMEN OUTPUT not less than 2000 Lumens 190 Supply,installtion ,testing loading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 15 to 20 W ,downlighter, IP rating not less than IP rating not less thanIP-20,size min 135mm dia,RECESS MOUNTED LUMINARY EQUI. TO CCT=CW(6500K), LUMEN OUTPUT not less than 2000 Lumens 191 Supply, installtion ,testingloading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 10 to 12 W, downlighter,IP rating not less thanIP-20 LED RECESSED MOUNTED LUMINARIES, CCT=4000K,LUMEN OUTPUT not less than 1200 Lumens, min 135mm dia. 192 Supply,installtion ,testing loading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge.5 to 6 W , downlighter, IP rating not less thanIP-20,RECESS / SURFACE MOUNTED LUMINARY EQUI. TO CCT=CW(6500K),LUMEN OUTPUT not less than 670 Lumens,min 135mm dia. 193 Supply,installtion ,testing loading ,transportation, unloadingat site, storages at site of following type light fittings includingrequired integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge. 30 to 40 W ,IP rating not less than IP66/IK08, STREETLIGHT LUMINARIES CCT=CW(5700K), LUMEN OUTPUT not less than 4700 Lumens 194 Supply and installation ofGalvanised iron 1000 mm long, Diameter minimum 20 mm, thickness minimum 2.0 mm , with 20⁰ Angle Single bracket type with FRP dome and ball suitable for street lightpoles/ exterior wall approximately mounting height of brackes & all necessary clamps & fixing accessories & weather proof Junction box (IP65) four terminal with single pole MCB &4 wire loop in loop out connectores sutaible for connection upto 10Sqmm AL Cable etc. 195 Supply, ofExhaust fan 150mm light duty ( Plastic body)230 V AC 50 Hz 1400 RPM with condenser complete erected in position with n/c materials Fan motor with moisture treatmentand class E insulationwith louvers 196 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep 197 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way(4+24)Double door 198 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way(4+24)Double door 199 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powderpainted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way(4+24)Double door 200 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs as required . (Note : Vertical type MCCB TPDB is normally used where 3 phase outlets are required.)12 way Double door 201 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 202 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Doublepole 203 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole 204 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 205 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A 206 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A 207 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 Way Double door 208 Supplying and fixing 63 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 209 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug topalongwith 20 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 210 Supplying and fixing following rating, four pole, 415 volts,MCCB Powder coated Metallic encloser with IP42 with cable termination spreder links complete with connections,testing and commissioning etc. as required.63 amps 211 Supplying and fixing following rating, four pole, 415 volts,MCCB Powder coated Metallic encloser with IP42 with cable termination spreder links complete with connections,testing and commissioning etc. as required. 125 amps 212 Incomer :63 Amp -3 Pole MCB + 1 No 3 Pole-63Amp Power Contractor 24 HrsGeographical multisettingTimer with Manual / Auto Selctor switch,ON-OFF PB, ON-OFF-TRIP Indication lamp& its control wiring etc.with Metalic enclosure IP5X panel to be considered 3b type Outgoing 6 Nos 32 Amp SP MCB , 10KA,C-CL 213 Supply of BLDC ceiling fan, 1400 mm, having rotor, 3 blades, downrod, caps , wires, white painted, 230 V AC , having full accessories for safe standard installation, as complete. 214 Supplying and fixing following rating, four way juction boxPowder coated Metallic encloser with IP42 withcable termination 4 way incoming & outgoingpower cableconnectors ,testing and commissioning etc. as required. 215 Supplying and fixing following rating, four way juction boxPowder coated Metallic encloser with IP5X ( for outdoor Type) withcable termination 4 way incoming & outgoingpower cableconnectors ,testing and commissioning etc. as required. 216 Supply, installation, testing and commissioning of INVERTER with sinusoidal wave output , 5KVA having offline inverter. 415 V Three Phase Input & Out put 240V ,50Hz, 15 min Back up with external Sealed maitnenance free battery of 12-48 V and minimum 1500 VAH. Mounting stand for battery and inverter having earthing terminals etc as complete. 217 Floor mounted bucket stand with buckets to hand 4 nos. of 13 ltrs buckets.The stand shall be 5(L) x 3(H) x 2(W) made out of 30 x 300 x4mm MS angle frame dulycoated with 2 coats of red oxide primer & 2 coats of red finish paint 218 Antiskid black rubber mat of approved make,12 mm thick 900mm wide x 1800mm Longchequered type as per IS-5424 in following1.1k.V. voltage grade . 219 First aid chart made of cloth for electricall shock treatment printed in English ,& Hindi duly framed with front glasses. 220 First Aid box with all the standard contents. 221 Portable 5 kg. dry type fire extinguisher suitable for electrical fire with pressure gauge on itand as recommended by the tariff advisory committee. 222 Supply, fabrication and installation ofMS material for cable tray supports, supports for cable trench covers, supporting frame for mounting of control panels, supports for mounting of local control station,Main Electrical Panel,lighting panel, lighting fixture etc. with 2 coats of enemel primer and 2 coats of epoxy paint Note - The rates shall be inclusive of grouting of supports , Anchor fastner,welding rods, nut,bolts,clamps,and any other consumable which required to complete the works. ( Note:- Supports are suitable for clamping of PEB structures ) 223 Supplying, installing and commissioning of CO2 type fire extiguisher of 4.5Kg with pressure guagefrom brand drawn steel cylinder as per IS 7285 with ISI mark and chief of controller.of explosive approval, fitted with wheel valvees as per IS3224 with ISI Mark with discharge hose & horn supplied complete with initial charge overall confirming to the IS: 15683 with IS Mark wall bracket. Fire rating 21B 224 Analogue addressable micro Process - controlled Fire Alarm Control Panels, capable of being IP networked to the central monitoring System, to monitor and integrated the following quantity of accossries like detectors, MCPs/hooters/control modules, Fault Isolation Modules, hooters, response indicators,fire/fault indicators, audio-visualsignals, central processing units, complete with LCD display, zone indicating LEDs as per the detailed specification: complete with 24V DC Battery backup with charger for each panel.Each loop should provided with minimum 125 detectors /devices, 2 LOOP PANEL 225 Supply, Providing Windows based graphicalsoftware for above fire alarm panels and detectors on MS windows 2000/XP with PC or latest platform,including Alarm Management for IBMS system. 226 Supply, Installation, Testing and Commissioning of Rate of Rise Heat Detectors (Thermal Detectors):GRADE-I Addressable analogue type Heat Detectors with solid state design with sensing element combination of fixed type and rate of rise of temperature indicating LED, mounting base etc. as per detailed specifications. 227 Supply, installation, testing and commissioning of Addressable analogue MULTISENSORtype smoke detectors with dual chamber, solid state design, indicating LED, mounting base etc. as per detailed specification.The rate shall inclusive of necessary base box, connecting glad for above detectors 228 Supply, installation, testing and commissioning ofHooter with relay module and storb light with minimum 85 db audiable and control relay module,24V DC power supply units etc 229 Supply, installation, testing and commissioning ofManual call points pull stations of approved make with NO/NC contacts slim type and projecting out from the surface of enclosurewith glasssuitable for addressable function 230 Supply, installation, testing and commissioning ofFault isolation module toelectricallyisolate different sections of detector loops. 231 Supply, installation, testing and commissioning ofAddressable control module to triggering the DVR etc 232 Supply, installation, testing and commissioning ofResponse indicator for mounting on false ceiling at the entries of the cabin for indicating the operation for detectors in the above areas. 233 Supply and fixing of 2R 1.5 Sq.mm FRLS PVC copper wire laid in existing conduit(Conduit work shall be done by Electrical contractor) 234 25mm dia Concealed PVC conduit for laying of fire cable including necessary accessories like bend, junction box fixing of clamps etc., (For detectors, MCPs and Hooter Power supply cable) 235 Supply& Installation of FMlisted Infrared optical Beam detector with suitable refecter /Transmitter andreceiver coverage of150-200 mtr distance as per detailed specifications with low level test unit.The adjustable angle shall be +/- 10 Deg for both vertical and Horizontal.The detector shouldhave suitable monitor module and capable of connecting toAddressable fire alarm panel. Bidder to submit detail along with offer 236 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supplying, installation, testing and commissioning of4-pair, Cat6-- UTP Cable,for Data /Telephone /Intercom /Access control/CCTV etc in exisitng laidconcealed/surface conduits/cables trays etc. The cat 6 cable shall be as per standard of ANSI/ TIA-568-C2- 237 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supplying, installation, testing and commissioning ofCat-6 , 1 port 110-style faceplate including all required consealed boxes, & accessores to complet the work. 238 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supplying, installation, testing and commissioning ofCat-6 ,-RJ45 Information outlet jacks 239 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supplying, & installation, of12 Uclosed rack with all standard assecories 240 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supplying, installation, testing and commissioning of 24-port loaded, Straight Jack Panel,1U 241 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Supply , unloading ,shifting ofOFC cable : 6 cores OS2 Singlemode armoured fiber cable, uni-tube, high density polyethylene outer jacket 242 Laying of OFC cable in ground through HDPE pipe of 40mm diameter including accessories coupling etc.incluidngHDPE pipe of 40 mm diameter and required accessories , as complete. 243 Design ,Supply,Delivering at site, receiving at site,installation, testing and commissiong of following Data Networking System as per tender specification andsystem architect drawing & including certifications. .Splicing / Termination of Fiber Optic Cable Cores using Fusion splicing with pre-terminated LC pigtails, dressing and proper fixing in splice trays. Including Splicing Kit. 244 Supply, Installation, Testing & Commissioning of Wall mounted LIU of various capacities for optical splicing/termination of fiber optic cable as per the design schematics. It shall be complete with adaptor panels, adaptors and splice trays for using LC type termination and asking/blanking/dustcover for unused/unmounted adaptor ports, inclusive of all mechanical accessories. Adequate splice trays shall be provided for proper management of splices for required number of cores at every LIU. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.for 12 cores, Singlemode LC termination 245 Supply, Installation, Testing & Commissioning of rack mouting lan switch with specification of48 portx 10/100/1000BASE-T PoE ports, 4 x Gigabit SFPports , Advanced L2 switching and security features ,L2+ Static Routing,370W PoE budget Port-based VLAN MAC-based VLAN Voice VLAN Number of VLANs supported: 4,096 246 Supply, Installation, Testing & Commissioning with specification of 1× 10/100/1000Mbps Auto-Negotiation RJ45 port supporting Auto-MDI/MDIXAuto-negotiation of Half-Duplex/Full-Duplex transfer modeComplies with IEEE 802.3ab and IEEE 802.3zFiber Connector: ST, SC, or FCFiber: Multimode, Single-ModeConnector: Dual FiberFiber to LAN Converter 247 Supply Installation Testing & commissioning of IP 4MP IR DOME CAMERA , with fixed Lens, 1/3 Progressive Scan CMOS, ICR, 0 lux with IR, : 25/30fps, 2.8 mm lens, H.265 / H.264/MJPEG, dual -Stream, BLC, UP to 30m IR, Vandal-proof, DC12V/PoE , Full HD, DWDR, 3D DNR, Smart IR, 30m IR, Support Intrusion detection, line crossing. ONVIF, UL LISTED. CERTIFICATE CE & FCC. 248 Supply Installation Testing & commissioning of IP 4MP IR BULET TYPE OUTDOOR CAMERA , with fixed Lens, 1/3 Progressive Scan CMOS, ICR, 0 lux with IR, : 25/30fps, 2.8 mm lens, H. 265 / H.264/ MJPEG, dual -Stream, BLC, UP to 30m IR, Vandal-proof, DC12V/PoE , Full HD, DWDR, 3D DNR, Smart IR, 30m IR, Support Intrusion detection, line crossing. ONVIF, UL LISTED. CERTIFICATE CE & FCC. 249 Supply Instalaltion, Testing & commissioning of Basic L2 features 16 Port PoE auto-sensing 10/100/1000 Network Switch with 2 SFP Port, 2 X 1G Uplink Ports including standard connectivity accessories. (for CCTV Camera) 250 Supply Installation Testing and commissioning of CAT 6 , UNARMOURED STP CABLE equvillant to to D-Link,AMP/digilink/ Cisco 251 SITC of IP, 16CH NVR, 2 SATA HDD Slot (Max 8TB), with 4 TB hard disk, of approved make, 12VDC,Realtime Recording Resolution (16 Channels @ 720P,8 Channels @1080P),Real-time Local Playback( 4 Channels @720P,2 Channels @1080P),Multiplex Operation,H.264 High profile,BNC/VGA/HDMI output, main profile, baseline,HDD Redundancy,Free DDNS,Network backup, USB HDD, USB writer, SATA writer,1 RS485, support 18 kinds of PTZ protocols,ONVIF 2.0,1 channel Audio Input and Output,Make-Honeywell CALNVR-2016B or equivalent approved make. 252 Supply, installation , testing and commissioning of 32 Smart LED FHD TV with minimum 2 nos HDMI inputes , as required ( Approved make : Vu / LG / Philips / Samsung / Sony ) 253 Supply installation tresting and commissioning of HVLS fans ( High volume Low Speed) Size of HVLS fan - 12 feet in diamterMake – Nutech / Echo Air / Crystal AlsanMinimum power Motor – 1.1 KWRPM range – 80 to 115 RPMWorking Height available form flooring to fan – Around 6 meters Fan type - Gear reducer AC motorMotor make – Lenze / NordVFD Drive make – ABB / Danfoss / Siemens/MitsubishiNoise level - Maximum 45dBA @ 5 meterPower Supply - 230V+10% & 50Hz+1%Blade Construction - Aluminium Alloy High Gradewith extra support system as briefed below,1) Double pivot adjustable mount2) Safety cable for extra safety 3) Hook for Hub4) Fan hub and bottom cover 5) Aerodynamic aluminium blades.This item includes HVLS fan of diameter 12 feet, starter panel with VFD drive, scaffolding, taxes Ets. nothing shall be paid separately.

INR 1180 /-

INR 740000.0 /-

INR 3.70 Crore /-

FileName	File Description	File Size
Click here to download tender document	Tender Notice	0 KB
Click here to download tender document	Tender Document	0 KB
Click here to download tender document	Tender Document	0 KB
Click here to download tender document	Tender Document	0 KB
Click here to download tender document	Tender Document	0 KB
Click here to download tender document	Tender Document	0 KB