Tender For special Repair To Md Accn Bldg No P-262/01 P-262/02 P-264/01 And P-264/02 In The Area Of Age B/R Ii At Rms- 1 Dismantling floor, hearth or wall tiling including cement mortar bedding (includingbacking), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed. 2 Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets etc complete all as specified and directed 3 Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. 4 Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. 5 Demolition of reinforced cement concrete of any description and inany position not otherwise specifically provided for etc complete all as specified and directed. 6 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified. 7 Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. 8 Taking downchowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame) etc complete all as specified and directed. 9 Taking down door chowkats with shutter exc 1.5 but not exc 4 sqm each (without taking off shutters from the frame) etc complete all as specified and directed. 10 Taking down door shutter exc 1 sqmtr but nex 2 sqmtr eachand removing to store complete all as specified. 11 S&F in replacement of 500 ltr capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ),incl provision of 20 and 25 mm dia spouts for inlet and outlet and connectionincluding 20mm diaBall valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), all specified in SSR Part-Icomplete all as specified & directed. 12 All as per item No 11.00 (here-in-before) but 1000 Ltrs complete all as specified and as directed by Engineer-in-Charge. 13 M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm etc complete all as specified and directed 14 All as peritem No 13.00 (here-in-before)but above 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders. 15 M&L for Cement Concrete type E2 (1:5:10) (using 40 mm graded stone aggregate) in foundation and mass concrete/sunken floors etc complete all as specified and directed 16 M&L for Cement concrete type B-1 (1:2:4), as in bedding layer for receving of vitrified ceramic tiles (using 20 mm graded stone aggregate), 25mm thick complete all as specified. 17 M&L for Coloured /light shade vitrified ceramic tiles 8mm to 10mm thick (square/regtangular) polished , area of each tile exc 0.18 Sqm but not exc 0.36 sqmin floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and incl 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. 18 M&L for Coloured /light shade vitrified ceramic tile 8mm to 10mm thick (square/regtangular) polished ,area of each tiles exc 0.18 Sqm but not exc 0.36 sqmmatching with floor as in skirting etc and laid over and including 10 mm thick bedding layer in CM (1:4) , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles all as directed. 19 M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick CM (1:4) screed bed etc complete all as specified and directed. 20 M&L forcoloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick laid over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and incl backing coat 10 mm thick in CM (1:4) etc all as specfied and directed. 21 M&L for preparing the sunken floor slab as specified and appying cement plaster coat laid to slope average 20mm thick in CM (1:3) finished even and fair and applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm etc complete all as specified and directed. 22 M&L for Water proofing treatmentfor sunken floor by applying bituminonus primer @ 0.20 kg/sqm providing and laying 3mm thick APP modifide water proofing membrane weighing not less than 3.00 kg/sqm reinforced with non woven polyster mett weighingnot less then 150gm/sqm having soften point not less then 140 degree centi grade, longitudinal tensile strength not less then 650N/Sqm, tearing strength of 180 N, by torch application incl min 10cm side over lap and 15cm end over lap and over the membrane etc complete all as specified and directed. 23 M & L for water proofing treatment of roofs using Dr fixit roof seal classic waterproofing coating that provide a seamless and though waterproofing barrier for old roofs over and including 25 mm thick cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in slope correction layer over RCC slab finished without using extra cement complete all as specified and as directed.Method of application:(1) Prepare the surface thoroughly by cleaning & washing (2) Check the hollow portion and fill it with cement sand mixed with Dr fixit U.R.P.(3) Apply one coat of Dr fixit prime seal ( diluted 2 part of prime seal with 1 part water ) (4) Apply two coat of Dr fixit roof seal classic at interval of 8 hours cure for the period of minimum 7 days . 24 M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or etc., and making good, cutting not exc 10 cm girth etc complete all as specified and directed. 25 S&F Pressed steel frames of size 105 X 60mm (1.25mm thick MS Sheet)for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified, supplied and fixed. Thickness of CRCA sheet 1.25 mm etc complete all as specified and directed 26 All as per item No 25.00 (here-in-before) but size 125x60mm with double rebate. 27 S&FPlain, solid straight chowkat and frames, wrought, frmedrebated on the solid, rounded or chamfred put together with glue pinned at joints , supplied and fixed in 2nd class hard wood etc complete all as specified and directed. 28 S&F35mm thick flush shutters factory made, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and as directed by Engr-in-Charge. 29 Supply and fix 35 mm thick factory made second class hard wood glazed and skelton shutter, open rbatd and prepared to receive glass, gauze etc (with out sash bar ) edges of framing plain, camfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I section 8 clause 8.42(a) supplied and fitted to chowkat etc complete all as specified and directed. 30 Supply and fix stainless stelel wire cloth 0.36 nominal dia of wire and average width apperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutter etc complete all as specified and directed 31 S&Ffor providing powder coated sliding type (3 Track +3 shutter) aluminium windows,ventilators excluding frame section profiles of aluminium as per sketch No SK/2019/01 dated 21/01/19,aluminium alloy extruded sections conforming to HE 9-WP of BIS 733 and HP 9 -WP of BIS 1285 as amended, with minimum thickness of frames (outer bottom, Top & side ) 1.5mm and sliding sash (stiles & rails) of minimum thickness 1.2 mm. The windows shall be procured from a BIS license factory manufactoring windows to BIS-1948, The EPDM gaskets, rollers, recessed handles cum locks aluminium snap beading for receving glass/wiremesh with stainlss steel screws shall b provided with windows. The aluminium extruded section shall be of make Jindal/Hindalco/Alom extrusions etc complete all as specified and directed.Note:- Glazing and Stainless steel wire mesh will be paid seperately. 32 S&F for anodised aluminium powder coated ( minimum thickness of powder coationg 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete as as specfied 33 S&F Aluminium decogrills made out of fixed indepently on outsode of sliding window system in Aluminium C channelon top & Bottom, wt of aluminium alloy grill not less than 1.5 Kg/m2 etc complete all as specified and directed 34 Supply and fix sheet glass selected quality 4.0mm thick, any size, tinted of approved colour fixed with rubber beading complete all as specifed and directed. 35 M&L for Preparing new wooden surface and applying two coats of synthetic enamel paint over a coat of pinkprimer complete all as specified and as directed. 36 M&L for Preparing old wooden surface and applying one coat of synthetic enamel paintcomplete all as specified and as directed 37 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing 38 S&F for Factory made solid panel PVC doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and directed 39 S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed 40 S&F 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and directed. 41 S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as specified and directed. 42 S&F Aluminium bow handles, cast type, anodised 150 mm long etc complete all as specified and directed. 43 S&F Aluminium bow handles, cast type, anodised 125 mm long etc complete all as specified and directed. 44 S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed. 45 M&L for Second class clean sawnhardwood in scantling fixed in timber framed work etc complete all as specified and directed. 46 M&L for 18 mm thick prelaminated Medium density fibre board, Exterior grade, fixed to timber frame-work with stain less steel screws fixed in repairsall as specified and as directed. 47 S&F 75mm longHasp and staple, safety type, aluminium anodised mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and directed. 48 S&F Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as specified. 49 S&F 150mm long mild steel ordinary rat tail rod pattern springs including roller and roller complete complete all as specified and as directed by Engineer-in-Charge. 50 M&L for Brickwork with subclass ‘B’ old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) etc complete all as specified and directed. 51 All as per Item No 50.00 (here-in-before) but in half brick thick walls built in CM 1:6, complete all as specified 52 M&L for Rendering 10mm thick cement plaster in CM (1:6) on other than fair facebrick work/concrete surfaces finished even and fair without using extra cement complete all as specified and directed. 53 M&L for rendering 15 mm thick cement plaster in CM (1:4) on fair face brick work/concrete surfaces finished even and fair with WPC @ 2% by weight of cement content and without using extra cement etc complete all as specified and directed. 54 M&L for rendering 5 mm thick cement plaster in CM (1:3) on ceiling finished even and fair complete all as specified. 55 Complete removal of existing treatmentand applying twocoat of oil bounddistemper white or tintedon walls over a coat ofprimer over 1.5mm thick wall care putty etc all as specificed and directed. 56 M&L for preparation of new plastered surfaces of wall applying two coat OBD white or tintedon walls over a coat ofprimer over 1.5mm thick wall care putty of approved shade all as specified and as directed. 57 M&L for preparing newely plastered surface of wall and applying two coats of oil bound distemper white or tintedover a coat of alkali resistant primer over 1.5 mm thick cement based wall care putty over ceiling etc complete all as specified and directed. 58 M&L for preparation of old painted surfaces by removing the existing treatment completely and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and 1.5mm thick coat of wall care putty complete all as specified and directed by E-in-charge. 59 All as per Item No 58.00 (here-in-before) but on newly plastered surfaces on external wall. 60 M&L for White wash in one coat on old plastered surfaces of ceiling including preparation of surfaces complete all as specified. 61 Taking down 20mm dia boreGI steel tubing and connection including cleaning etc complete all as specified and directed. 62 Taking down 25 mm dia boreGI steel tubing and connection including cleaning etc complete all as specified and directed. 63 S&F in repairs Vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, andcover and mild steel chromium plated or aluminised hinging device etc complete all as specified and directed. 64 S&F in repair Vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand,brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified. 65 S&F in repairflushing cistern 10ltr capacity body molded from design quality high impact polly propylene critical, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 15mm bore 450mm long PVC connection all as specified and directed by Engineer-in-charge 66 S&F CPVC pipes, SDR 11 , 25 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end oieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling complete. 67 All as per Item No 66.00 (here-in-before) but of 20mm dia. 68 S&F in repairs PVC connection low density polythene pipe 15 mm dia , 450 mm long , heavy duty with PTMT nuts etc complete all as specified and directed. 69 S&F in repairs Pillar tap Brass CP mixer for mixing hot & cold water screwed down for iron pipe etc complete all as specified and directed. 70 S&F in repairs 15 mm bore Bib cock with wall flange and aerator,brass chromium plated with fancy type and screwed down to 15mm bore GI tubing or for brass ferule including taking down old bib cock etc complete all as specified and directed. 71 S&F in repairs Angle stop valve with wall flange 15 mm bore of pipe brass chromium plated, screwed down, high pressure screwed both ends for iron pipe for unions and fixed including taking down old stop valve and directedd by Engr- in charge. 72 S&F in repairs Brass chromium plated toilet paper holderall as specified and as directed. 73 S&F in repairs Stainless steel soap dish white of size 160 x 160 x 90 mm as approved fixed with brass screws or embedded in wall completeall as specified and as directed. 74 S&F in repairs Health faucet of brass body with wall hook and 1mtr flexible stainless steel braided rubber hose pipe fixed in repairall as specified and as directed. 75 S&F in repairs Towel rail chromium plated fancy type 60cm long including bracket fixed between flanges complete complete all as specified and as directed. 76 S&F in repairs Brass chromium plated over head 15 mm boreshower rose 120mm diawith 3 flow swivel jointincluding shower arm fixing to steel pipe or union including taking down old shower rose complete all as directed and specified. 77 S&F in repairs Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed etc complete all as specified and directed. 78 S&F in repairs 600 X 450mm bevelled edgemirror of selected quality glass, mounted on 6mm thick AC building board fixed to wooden plugs withCP brass screws and cup washers complete all as specified and direced. 79 S & F for0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and as directed. 80 S & F for 12 mm thickPlywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed. 81 S&F 30mm thick continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed. 82 S&F 125 mm Brass handles, cast type,polished bright complete all as specified and as directed. 83 S&F drawer magnet for cabinets/cupboard complete all as specified and as directed. 84 Supply only Integral Water ProofingCompound etc complete all as specified and directed. 85 S&F in repair PVC (SWR) pipes of dia110mm boredouble socketed in any lengthwith rubber ring joints fiexed to walls etc complete all as specified and directed. 86 S&F in repair PVC (SWR) pipe of75 mm bore in double socketed in any lengthwith rubber ringjoints fixed to walls.etc complete all as specified and directed. 87 S&F PVC Nahani traps 75 mm outlet with stainless steel cover grating etc complete all as specified and directed. 88 S&F PVC (SWR)bends of 75mmbore in radius etc complete all as specified and directed. 89 S&F PVC (SWR)bends of 110 mmbore in radius etc complete all as specified and directed. 90 S&F Salt glazed stone ware gully traps square or round mouthed type 150 mm x 150 mm. type P etc complete all as specified and directed. 91 M&L for Cement concrete type C-0 (1:3:6) (12.5 mm graded stone aggregate)in MS pipeposts and mass concrete on roof top etc complete all as specified and directed. 92 M&L for Preparation of two coat of synthetic enamel paint over one coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise describedall as specified and directed by Engr-in-Charge. 93 M&L for Preparation of two coats of synthetic enamel paints surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint, over a coat of red oxide, zink crome primer etc complete all as specified and directed. 94 M&L for Preparation ofold painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) all as specified and directed by Engr-in-Charge. 95 S&F in repairs 20 mm dia powder coated aluminium curtain railsfixing with fancy brackets and closing caps all as specified and as directed. 96 S&F Gun metal globe or gate valves suitable for 25mm bore pipe with iron wheels head , screwed both end for iron pipe complete all as specified and directed. 97 S&F in repairs 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , ovesinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmrall size of sink 495mmx420mm, bowl size 410mmx330mmx 160 mm as in repair complete all as specified. 98 Supply and fixing in repair stainless steel (conforming to AISI-304 grade) plate rack of overall size 750mm x 600mm x 254 mm or equivalent made of 1mm thick stainless steel sheetfixed on CP cantilever brackets, etc. complete all as specified and directed. 99 S&F size of grid 605 x 605 mm GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre with & including4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer boardE-Board Classic etc complete all as specified. 100 M&L Cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified. 101 M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-Charge. 102 M & L 25mm thick and 200mm vide second class hard wood boarding , plained one side with butt joints as ineaves boards etc complete all as specified and directed. 103 M&L for 75 mm thick PCC (1:3:6) type C-2 , (using 40 mm graded stone aggregate)as in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) etc complete all as specified and as directed. 104 Taking down carefullycopper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling,floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed. 105 Material and labour for (concelaed Type) point wiring including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessoriesand sunk modular GI box for mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge 106 Onelight pointcontrolled by one, one way switch . 107 One Ceiling fan/ exhaust fan point controlled by one, one wayswitch. 108 One 3 pin socket outlet 5 Amps on the same board with other switches. 109 One 3 pin socket outlet 5 Amps on the Independent board. 110 One bell pointcontrolled by one, one way switch . 111 One light point control by two way switch 112 All as per item No105.00 (here-in-before) but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 113 M&L for Modular Switch 1 way 6A,1 moduleetc complete all as specified and directed. 114 M&L for modular switch 1 way 16A, 1 module etc complete all as specified and directed. 115 M&L for Modular Socket ,6A/2/3 pin combined 2 module etc complete all as specified and directed. 116 M&L Modular Socket ,6A/16A-2/3 pin combined 2 module etc complete all as specified and directed. 117 M&L for modular Bell push 1 Way 6A 1 Module etc complete all as specified and directed. 118 M&L for bell AC 230 volts musical type etc complete all as specified and directed. 119 M&L for Modular Fan step regulator, 120W - 2 module etc complete all as specified and directed. 120 M&L for Modular switch 2 way 10A 1 module etc complete all as specified and directed. 121 Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn throughand including non metalic rigid PVC conduit with all conduit accessories (including concealing and making good to the disturbed surfaces of walls, ceiling,floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface) complete all as specified and as directed. NOTE:- two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length. 122 M&L for 20W LED, 4, Wall mounted LED tube light fitting batten with LED single side or double side connection, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same onand including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting including taking down old unsv light fitting complete all as specified and as directed. 123 M&L for 10W LED, 2, Wall mountedpolycarbonate batten internally pre-wired with electronic driver and polycarbonate diffuser and fixing the same onand including two Nos PVC blocks and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fittingincluding taking down old unsv light fitting complete all as specified and as directed. 124 M&L in replacement for decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lampwith B-22 baseincluding taking down old unsv holder fitting complete all as specified and directed. 125 M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. 126 M&L for Bldg Security LED 1x25W light fitting, drawn through including GI bracket of 25mm borelight grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holesas required and connecting upwith flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fittingincluding taking down old unsv light fitting complete all as specified and directed 127 Supply and fixing for Bed side light 3Watt LED light reading in bed just got easier with this colletion of adjustable LED bedside lights complete all as specified and as directed. 128 Supply and fixing Rigid non-metallic PVC conduit20mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed. 129 Supply and fixing for TV Socket 1 Modulecomplete all as specified and as specified. 130 Supply and fixing for RJ 11 Tele phoneSocket 1 Module complete all as specified and as specified. 131 Supply and fixing for Metal flush box 1/2 module complete all as specified and as specified. 132 Supply and fixing for White cover plate with frame, 1 module complete all as specified and as specified. 133 M&L for MCB Distribution board double door type SPN 12 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacityincluding taking down old unsv DB and making good the disturbed surfaces to match with existing specification , complete all as specified and as directed..Note : MCBs will be measured sepeartely. 134 S&F sheet metal enclosure with socket plug top and MCBs single pole 32 Ampsand neutral encloser with two pin and earth plug and socke complete one single pole MCB SP 20 Amps includingmetal encloser all as per specified and as directed by Engr-in-charge. 135 MSupply and fixing MCB SPN 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBincl taking down old unsv MCB complete all as specified and as directed 136 Supply and fixing MCB SP 6 to 32 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DBincl taking down old unsv MCB complete all as specified and as directed 137 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m complete all as specified and directed. Note : Old Exhaust Fan deposted EM store yard. 138 Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.Note : Old Exhaust Fan deposted EM store yard. 139 Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades,hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed. 140 Supply, installation, testing and commissioning of factory made meter panel board wall mounted made out of CRCA sheet of 2mm thick indoor type totally enclosed weather proof, dust vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body duly grouted in wall including provn of Acrlylic sheet for meter reading, space for refixing of single phase smart meter 5-60 Amps 04 Nos AC 230 Volts incl lugs, spacer mounting chanels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc, suitable compartment of every meter and control MCB circuit and epoxy powder coated spray paint with primer, suitable arrarments for incoming MCCB and outgoings with copper bus bar and terimal links, CPRI type tested complete all as directed including the following accessories :- Incoming (a) MCCB 63 Amps 4P, 415 volts, 16 KA - 01 No (b) R-Y-B phase LED indicating lamp 03 Nos (c) Copper wiring in panel of suitable size.Outgoing (a) MCB SPN 40-63 Amps, 230 volts 10 KA C Curve - 08 Nos and MCB SP 6-32 Amps -02 Nos (b) Refixing existing smart meters - 04 Nos ( Note : to be insured properly maching the qtr Nos before fixing the smart meters) 141 M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i)The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI cover 10 m thick, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSRPart-II. (ii)Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable
