Tender For Construction Of Acr For Gms Soura.- 1 Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in all kinds of soils 2 Providing and laying of hand packed stone boulder (size 150mm-230mm) before laying of PCC compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job. 3 Supplying and filling in plinth with earth under floors including, watering, ramming, consolidating and dressing complete. 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 5 Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 6 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including curing. 7 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with( 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 8 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including curing. 9 All works up to plinth level 10 All works above plinth level 11 Centering and shuttering including strutting, propping etc. and removal of form for: 12 Foundations, footings, bases of columns etc. for mass concrete. 13 Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc 14 Suspended floors, roofs, landings, balconies and access platforms. (Steel plates only) 15 Edges of slabs and breaks in floors and walls, Under 20 cm wide 16 Lintel, beams, plinth beams, girders, bressumers and cantilevers. 17 Stairs (excluding landings) except spiral staircases. 18 Columns, pillars, piers, abutments, posts and struts. 19 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructureupto floor Level-V including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) the cost . 20 12 mm thick cement plaster in 1:6 cement mortar in walls using coarse sand. 21 6 mm thick cement plaster in 1:3 cement mortar in walls using Finesand. (to ceiling) 22 Providing and applying white cement based putty of specified thickness,of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete.1 mm thick 23 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shadecomplete 24 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer 25 Finishing walls with water proofing cement paint of required shade onNew work (two or more coats applied @ 3.84 kg/10sqm) 26 Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 27 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work 28 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. Complete40mm thick with 20 mm nominal size stone aggregate. 29 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): KD wood 30 Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm(anti skid) 31 Float glass panes 3.5 mm thick glass pane (weighing not less than 10 kg/sqm) 32 Providing and fixing factory made flush door shutters 30 mm thick made ofpre-laminated flat pressed three layer particle board conforming to IS: 12823 exterior grade (Grade I Type II) having one side decorative lamination of approved shade and other side balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and black enameled M.S. butt hinges complete as per directions of Engineer- in-charge 33 Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :First class KD wood 34 Providing and fixing 35mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class KD wood 35 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 36 Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete :125mm 37 Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete ::100mm 38 Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 39 100x10 mm 40 150x10 mm 41 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto & above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. 42 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 43 White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 44 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixedto wooden cleats with C.P. brass serews and washers complete. 45 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. 46 Providing and fixing un plasticized P.V.C. connection pipe with PTMT nuts, collars and bush of approved quality and colour 15 mm nominal bore with 30 cm length. 47 Providing and fixing un plasticized P.V.C. connection pipe with PTMT nuts, collars and bush of approved quality and colour15 mm nominal bore with 45 cm length. 48 Providing and fixing PTMT liquid soap container 109 mm wide. 125 mm high and l112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 49 Providing and fixing wash basin with Cl. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutling ad making good the walls wherever (a) White Vitreous Chia Wash basin size 550x400 nm with a 15 mm CP Brass single hole basin mixer 50 Providing and lixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipcs and fittings. 51 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 52 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 53 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe 32mm 54 Providing and fixing PTMT Waste Coupling for wash basin and sink, ofapproved quality and colour: 55 Providing and fixing Wall mixer/Sink of approved make 56 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as perI.S. 13983 with C.I. brackets and stainless steel plug 40 mm, includingpainting of fittings and brackets, cutting and making good the wallswherever required :Kitchen sink without drain board 610x510mm bowl depth 200mm 57 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 58 Providing and fixing 100 mm CP Grating of approved quality conforming to IS : 8932 59 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good thewall etc. 60 PN-16 pipe , 25mm OD(SDR-7.4) 61 External work including trenching, refilling etc. 62 PN-16 pipe , 25mm OD (SDR-7.4) 63 PN-16 pipe , 32mm OD (SDR-7.4) 64 Providing and fixing PPR Unions 65 PPR Union 20mm 66 PPR Union 25mm 67 PPR Union 32mm 68 Providing and fixing Ball valve brass of approved quality 69 25 mm nominal bore 70 32 mm nominal bore 71 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 72 Providing and fixing PVC pipes including PVC fittings laid in required gradient, including cost of all fixing accessories complete job as directed by EIC 73 50 mm dia 74 75 mm dia 75 100 mm dia 76 Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 77 Providing and fixing precoated galvanised steel sheet roofingaccessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) 78 Providing and fixing0.40mm thick plain boarding (MS) in fascia/soffit including cost of underneath frame work of of wooden jambs of size 50x25 mm, including wooden cornice of required size.The job shall also include scaffolding etc 79 Providing and fixing plained eaves boarding.2nd class kail wood 250x32 mm (nominal size ) 80 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded 81 Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels(16 mm)( Raj Nagar plain white marble/Udaipur green marble/zebra black marble(Area of slab over 0.5 sqm) 82 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes 83 Carriage of materials from source to site of work: 84 Sand 12 Km MT 85 Aggregate 20 km M.T 86 Brick 28 Km MT 87 Engagement of JCB for dismanteling of old damaged 3 no. single storey structures within premises of school 88 Disposal of unserviceable material from site to outside the municipal limits by mechanical limits using tractor,loading and unloading complete job(lead upto 10km) 89 Add GST applying factor 0.2127 multiplying factor 1.2127 and dividing factor 1.2127
