Tender For Proposed Development Work At Khanta Picnic Spot District-Sonebhadra, 1 Proposed Development work at Khanta Picnic Spot District-Sonebhadra. 2 (Civil work) 3 Cleaning jungle including uprooting of rank vegetations grass,bush,wood trees and saplings of girth upto 30 cm. measured at a height of 1 meter above ground level & removal of rubbish upto a distance of 50 meters outside the periphery of area cleared 4 Excavation in foundations in ordinary soil (Loam clay or sand) including lift upto 1.5 m (5 fts.) and lead upto 30 mt. (100 fts.) & including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-Incharges upto a distance of 30mt. (100 fts) from the foundation trenches. 5 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. hardrock (requiring blasting) 6 Filling of earth in plinth in 20cm layer including leveling, dressing and watering and also including of supply of earth including carted loading & unloading as per direction of Engineer incharge.. 7 Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 km. (5 miles) from the site of work and including watering, ramming, dressing etc rate to include cost of all materials, labour and T & P etc required for proper completion of the work. 8 Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & floors. 9 Making drain along with the apron. 10 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 11 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 12 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 13 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 14 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).Footing. 15 R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in Column excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-20. 16 Class M-150brick work in 1:4 cement and coarse sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour, and T & P etc.required for proper completion of the work. 17 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Foundationabove plinth level up to floor v level in all shapes and size in:1:6 (1 cement : 6 sand) 18 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor v level in all shapes and size in:1:6 (1 cement : 6 sand) 19 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor v level in all shapes and size in:1:4 (1 cement : 4 sand) 20 Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). 21 Providind & applying a coat of resudual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square meter on damp proof course afte cleaning the brushes and finally with a piece of cloth lightly soaked in kerosene oil. 22 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: 23 (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment 24 (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. 25 (C ) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. 26 (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. 27 (e ) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 28 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 29 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 31 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. 32 Hold fast for chaukhats of doors/windows. 33 Door / windows & Staircase grill. 34 Z-Section windows 35 Angle iron door chaukhat 35*35*5 36 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 37 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :Kiln seasoned and chemically treated hollock wood30 mm thick shutters 38 thick shutters 39 P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and and over lapping & hooks. 40 Fixing of Door, windows/ventilators chaukhats in position. 41 (a) Door chaukhats 42 (b) Window chaukhats 43 (c) Ventilator chaukhats 44 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 coarse sand) 45 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 coarse sand) 46 Ground floor 47 12 mm cement plaster of mix : 1: 6 (1 cement : 6 coarse sand) 48 6 mm thick plaster in 1:3 cement & coarse sand on ceiling and soffitsof stairs upto floor two level. 49 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. 50 Making drip coarse in sun shade or facia with 1:3 cement and fine sand mortar as per direction of Engineer -in-charge including supply of all materials, labour, Tools & Plants etc required for proper completion of the work. 51 mm 52 mm 53 Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (25 mm thick floor). 54 Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (40 mm thick floor). 55 Providing and glass strip, joints of floor skirting dado at time of laying floors flush with floor level including supply of all material labour and T&P etc. required for proper completion of work. Same as above but 3.5 cm depth. 56 Supply / fixing Ceremicof first quality in flooring or in skirting or dado laid with 1:3 ciment and approved coarse sand morter finished with white cement slurry jointing and polishing complete including supply of all materials, labour, T&P etc. requred for proper completion of work.300x300 57 Supply / fixing 6mm china glazed tiles/Ceremicof first quality in flooring or in skirting or dado laid with 1:3 ciment and approved coarse sand morter finished with white cement slurry jointing and polishing complete including supply of all materials, labour, T&P etc. requred for proper completion of work. 58 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 59 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 60 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade (Area of slab upto 0.50 sqm) 61 40 mm thick Mirzapur sand stone over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. 62 Stone carving work 63 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 64 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture 65 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture 66 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 67 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 68 Providing and applying white cement based putty of average thickness 1 mm, of approved brand &anufacturer, over the plastered wall surface to prepare the surface even & smooth complete. 69 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes 70 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm 71 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 72 (a) 250 mm x 10mm 73 (a) 200 mm x 10mm 74 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm 75 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design. 76 Supplying and fixing rolling shutters of approved make, made of requiredsize M.S. laths, interlocked together through their entire length andjointed together at the end by end locks, mounted on specially designedpipe shaft with brackets, side guides and arrangements for inside andoutside locking with push and pull operation complete, including thecost of providing and fixing necessary 27.5 cm long wire springsmanufactured from high tensile steel wire of adequate strengthconforming to IS: 4454 - part 1 and M.S. top cover of required thicknessfor rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover 77 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: 78 a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm 79 laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. 80 (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. 81 (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose ofeasurement the entire treated surface will be measured. 82 Centering and shuttering including strutting, propping etc. and removal of form for : 83 Foundations, footings, bases of columns, etc. for mass concrete 84 Columns, Pillars, Piers, Abutments, Posts and Struts 85 Lintels, beams, plinth beams, girders, buttresses and cantilevers. 86 Suspended floors, roofs, landings, balconies and access platform. 87 ELECTRICALM 88 Wiring point for light with 1.50 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable earth continuity wire, piano type switches & ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash. Group C 89 Wiring point for two ways light with 1.50 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire and two number two way piano type switches & ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash. 90 Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.50 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire, piano type switch & ceiling rose on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash. Group C 91 Wiring point for plug with 2X4 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1X4 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire and piano type switches & socket etc., complete in all respects as directed, including matching color wash. 92 Wiring points for Call bell with 1.50 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire and piano type bell push or 2pin socket etc.complete in all respects.as directed including matching colour wash. 93 Wiring points for Light point/fan/exhaustCall bell with 1.50 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduitpipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire and modular type switches/socket etc.complete in all respects.as directed including matching colour wash. Group C 94 Supplyfixingand concealing of20mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work. ( T.V. /Telephone) 95 Supply & wiring of submains with two number2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. 96 Supply & wiring of submains with two number4 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. 97 Supply and wiring of submain 2 number 6 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in20mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 6.0 Sqmm FRLSH PVC Multistand copperearth contunity wire including colour wash etc. complete in all respects. 98 Supply and wiring of submain with two number 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multi strand single core copper conductor cable in 20 mm dia. heavy duty (2 mm thick) PVC conduit with 1 number 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multi strand core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect. 99 Supply & fixing of single wall bracketon matching M.D.F.E.G.boardbase etc. complete in all required. 100 Supply & fixing of fancy type round ceiling fitting made of polycarbonate for and with 1x 15/18 watt CFL complete in all respects. 101 Supply & fixing of factory wired Box/ Channel type T-5 energy saver with bright anodized aluminium reflector and end covers suitable for 1 No. 28 watt T-5 lamp with 1X28 watt T-5 lamp etc. complete as required. 102 Supply & fixing of factory wired HPF box type, flourescent tube light fitting suitable for 1x20 / 1x18 watt decorative mirror complete including tube etc.on surface complete in all respects. 103 Supply & fixing of Call Bell/buzzer Of Approved Make on matching polishedMDFEG boardbrassincludingconnectionetc. as required. 104 Supply and burying of 40mm dia x 4.5 metres long G.I. pipe, vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No.6 to 8SWG G.I.wire in G.I. pipe upto appron (and from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I.box with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects. 105 Supplying & Laying of 25mmx5mm G.I. Strip for earthing purpose as required complete in all respects. 106 Supply & fixing of two number 6 SWG G.I. wire for earthing purpose as required complete in all respects. 107 Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve5 - 32 amps.Cat. A 108 Supply and fixing of 40/63 Amp MCB(10KA)C Curve 63 Amp. 4 Pole MCB Cat. A 109 Construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, T & P etc. required for proper completion of work. 600x480x200 mm. size 110 Supply and fixing of factory fabricated M.S. box in existing sunk with Godrej type almirah cover with handle etc. fabricated from 18 SWG M.S. sheet duly painted with red oxide primer followedby two coats of synthetic enamel paint complete with necessary conduit entry and DP/TPN; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and T & P etc. required for proper completion of the work.600x480x200 mm. size 111 Supply and fixing of flush/surface mounting distribution boardswith additional metal door without MCBcomplete in all respects.6 Way TPN Cat. A 112 Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6sqmm cables, including tapping with insulating tape,etc. complete in allrespects. 113 Supply and fixing of single pole MCB blanking plate 114 Supply and fixing of power plug with 15A/250 V flush type switch and 3 Pin 15 A/250V flush type socket in suitable M.S. box of 175mmx100x50mm size Switch bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer. 115 Supply & fixingof Sheet Steel Enclosure Surface/ Flush Mounting fitted With 20/32 Amp. 2Pin and earth metal clad scraping earth plug and socket complete in allrespects as per direction and satisfaction of engineer-in-charge. 116 Erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. 117 Supply & fixing of 16 gauge M.S.drum duly painted including making hole in the wall for exhaust fan and finishing properlyetc. complete as required. 118 S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work. 119 Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sqmm 4 core 120 Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per dire 10 sqmm 4 core 121 Supplying and fixing of Palm / pin type copper tin plated cables sockets (lugs) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer-Incharge.10 Sq.mm 122 Supply and fixing of danger board fabricated from 10 gauge M.S. sheet as per I.E.rules. 123 Supply and laying of 1800mm x 900mm x 12mm thick chequered rubber matting of tested quality. 124 Supply and fixing 400 AMPfour pole Moulded case type on load change over switch with enclosure(also suitable for panel mounting with extra cost of bus bar) including the cost of labour, T & P , painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge.- 125 Supply and fixingofsingle phase multifunctional electronic energy meter 10 to 60 Amp. capacity fitted in integral box on wall complete in all respect. 126 Supply and fixing of LED street light fitting having diecast aluminium body and diffuser with driver set suitable for 150 watt. confirming to IP 65 and above protection complete in all respect. 127 Supplying and drawing following pair 0.5 sqmm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required.2 pair 128 Supplying and drawing co-axial TV cable RG-6 graded, 0.7 mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 129 Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections but excluding modular plate etc as required. 130 Telephone socket outlet 131 TV antenna socket outlet 132 Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75mm X 75 mm X 60mm Deep 133 Supplying and fixingfollowing size/modules, GI box along with modular base& cover plate for modular switches in recess etc as required.1 or 2 Module (75mm X 75 mm) 134 Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. 135 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 136 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.100 mm Dia 137 Supply and installing of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 300mmwidth x 62.5mm depth x 2.0mm thickness 138 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 139 Supply of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX 300mm sweep. 140 Supply,instalation,testing, commissioning of 3 phase,KWH Meter with LCD display, RS pot, Wired Communication system with current limiter switch & reset button. (Make:-L&T) 141 SANITARY. 142 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required 143 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 144 Same as above but for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware. 145 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require 146 a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap. 147 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board of size 510x1040x200mm 148 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe 149 a) 32mm dia 150 b) 40mm dia 151 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 152 Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. 153 15mm nominal bore 154 Providing & fixing 60x2cm. C.P. brass towelrail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw. ESSCO AEC-1111 155 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore 156 Providing 15 mm dia. inletC.P. brassProviding and Fixing C.P. Single flow overhead shower(With Arm)-ESSCO EOS-542A-125MMDIA 157 Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. 158 32 mm dia nominal bore. (medium duty) 159 Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work. 160 32 mm diameter pipe. 161 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 162 25 mm nominal outer dia Pipes 163 40 mm nominal outer dia Pipes 164 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 165 15 mm nominal outer dia Pipes 166 20 mm nominal outer dia Pipes 167 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.110 mm 168 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm 169 Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc. 170 a) 25mm dia nominal bore (medium duty) 171 a) 20mm dia nominal bore (medium duty) 172 Concealed pipe including painting with anticorrosive bitumatic paint, cutting chases and making good the wall. 173 a) 15mm dia nominal bore 174 b) 20mm dia nominal bore 175 Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.15mm nominal bore 176 Providing & fixing CP brass short body of approved quality conforming to15mm nominal bore 177 Providing and fixing gun metal gate valve with wheel of approved quality. 178 25mm dia nominal bore 179 32MM 180 Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 181 a) 15mm nominal bore 182 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 183 a) 20 mm nominal bore 184 b) 25 mm nominal bore 185 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 186 a) Circular Tank 187 Supply and fixing of UPVC SWR pipe type -B confirming to IS-13592 including jointing the pipes with rubber ring lubricant and UpVC SWR cuplar confirming to IS-14735 also including excavation of trences as before but excluding supply and cost of other fitt 188 a) 110mm diameter 189 b) 160mm diameter 190 Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. 191 a) 110mm diameterS.W.R. Pipe 192 b) 160mm diameterS.W.R. Pipe 193 Providing and fixing square mouth UPVCS.W.R. Gully trap grade A complete with C.I. grating brick masonry chamber with F.P.S. bricks of class designation 75 and water tight C.I. cover with frame of 300 x 300mm.size (inside) the weight of cover to be not 194 less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design. 195 a) 150 x 110 mm. size P type 196 With Sewer bricks conforming to IS : 4885 197 Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design 198 Inside size 90x80X50cms including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). 199 With FPS bricks of class designation 75 200 (i) For Sewer Line 201 Extra for depth of man hole size 90x80 cm 202 EXT. ELECTRI. 203 BOLLARD LIGHTS 40 to 45Watt 204 Supplying and fixing of 16mtr high mast shaft of apporved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 3mm. Top dia minium 150mm bottom dia 360mm base plate 32mm thick suitable for wind velocity as pe IS 875 part 3& having no circumferential weld with accesories for high mast suh as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5HP power tool moter 3point suspension system with steel wire rope 6 mm dia double drum winch including making suitable foundation as per manufacture drawing/ site reiment along ith foundation bolt nuts wahers anchors plates etc complee in all respect. 205 S.I. & Testing of 7.0 m high octagonal G.I. Pole with single arm as per approved sample made from 3 mm sheet steel (Grade S 355 JO) with top diameter as 75 mm and bottom dia as 150 mm and base plate of 240x240x16 mm with suitable slot shaped holes for mounting the same on a shallow foundation, GI weather proof junction box with 16 A SP MCB, loop-in-loop out terminals for 2 nos. 4Cx16 sq.mm YWY cables and 3x2.5 sq.mm copper conductor from junction box to fitting and connected accessories as required etc. Contractor to include the cost of RCC foundaiton for pole as per structural details. 206 Supply and fixing of LED street light fitting with mandatory driver set having die cast aluminium body and lenses suitable for 60 watt to 72 watt confirming to IP 65/66 protectioncomplete in all respect. 207 Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 volts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. 501 208 a) 25sqmm 3.5 core 209 b) 16 Sqmm 4.0 core 210 c) 10sqmm 2 core 211 S/F of 32A 415VTPN metal clad TPN HRCtype switch fuse unit complete in all respects. PWD 326 212 S/F of 32A 240V SPN metal clad rewireabletype switch fuse unit complete in all respects. PWD 302 213 HPRTICULTURE. 214 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, byspreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). 215 Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). 216 Supplying and stacking at site dump manure from approved source including carriage upto 1 km (manure measured instacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm. 217 Carrigae of manure upto 5 K.M. 218 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge. 219 Grassing with selection No. 1/ Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately). 220 Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and rammingwith required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge 221 Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S (non modular) bricks of Classdesignation 7.5 222 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately 223 Providing and displaying of Aglaonema Butterfly plant having ht.30 cm 10 to 12 fresh, healthyand attractive colorful leaves, well developed in 25 cm size Earthen pot/Plastic pot & as perdirection of the officer-in-charge 224 Providing and displaying of Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliagein 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. 225 Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags 226 Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge 227 Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge. 228 Making tree guard 53 cm dia and 2 m high as per design from empty coal tar drums, suppliedfree by the department, including providing and fixing four legs 40 cm long of 30 x 3 mm M.S.flat riveted to tree guard and providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixedwith rivets complete in all respects including painting inside and outside of tree guard with 229 GYM EQUIPMENT. 230 Providing and Fixing of Fun Walker 231 Providing and Fixing of Shoulder Press 232 Providing and Fixing of Chest Press 233 Providing and Fixing of leg Press StandingTwistar 234 Providing and Fixing of Leg Lift Post 235 Providing and Fixing of Shoulder Press 236 Providing and Fixing of Pendulum CumTwistar 237 Providing and Fixing of Fun Cycle 238 Providing and Fixing of Ski Trainer 239 Providing and Fixing of Step Trainer 240 Providing and Fixing of Chest Press 241 Providing and Fixing of Tai Chi Double 242 CHILDREN PLAY EQUIPMENT 243 S/F of Double Seesaw 244 S/F of Playground Slide. 245 S/F of Wheel chair swing size 14x8x10 ft. 246 S/F of 3Seater Arch rubber belt swing size 13z3.50z8 ft. 247 S/F of 2Seater seesaw size 6x2.29 ft. 248 BORING WITH SUBMERSIBLE. 249 External W/S arrangements with T.W. boring of 150 mm dia with 110 mm dia P.V.C. pipe assembly, 2.00 H.P. submersible pump including supply of all accessories starter, panel etc. & pipe arrangements etc . 250 110MM PVC casing pipe of ISI mark. 251 110MM PVC slotted pipe of ISI mark. 252 P/ F 50mm GI pipe (B) class. 253 Nylon mesh for filter. 254 Plastic dori. 255 Solvent cement. 256 110mm End cap. 257 110mm Submersible cap. 258 50mm MS clamp (Heavy). 259 50mmGI elbow. 260 50mm X 110mm GI nipple. 261 2 HP 9 Stage submersible pump of ISI mark with automatic panel. 262 2.5 sqm. Submersible cable. 263 Drilling charges for 6 dia tubewell. 264 Pea Gravel. 265 2 MS socket. 266 Cartage of material upto site. 267 Fixing testing and commissioning of Pumpset with lowering & Electric wiring with starter etc. complete as required. 268 DEVELOPMENT WORK. 269 Providing and laying Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site. (DSR-16.78.2) 270 Providing and laying 80mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 271 Providing and laying 80mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc Including sub grade b/w etc all work complete as per the direction of Engineer-in-charge. 272 P/Lincementconcrete 1: 2: 4 (1 Cement : 2 coarse sand : 4 gradedstone grit20mm nominalsizeandcuring complete including cost of form work for fixing of hold fasts including of supply of all materials labour T&P etc.required for propercompletion of work. Strength should not be less than M-20. 273 Providing and laying in position bitumen hot sealing compound for expansion joints etc. 274 P/Laying of C.C. road 1:2:4 cs mortar including base edging etc all work complete as direction by engineer in charge. 275 P/Fixing of Signages incuding comple work as per direction by engineer. 276 P/Fixing of Fountainincuding comple work as per direction by engineer. 277 P/Fixing ofFloating Jettyincuding comple work as per direction by engineer. 278 P/Fixing ofPaddle Boatincuding comple work as per direction by engineer. 279 P/Fixing ofkioskincuding comple work as per direction by engineer. 280 P/Fixing ofZorbingincuding comple work as per direction by engineer. 281 P/Fixing of Benchesincuding comple work as per direction by engineer. 282 P/Fixing ofDrinking Water Coolerincuding comple work as per direction by engineer. 283 P/Fixing ofDustbins incuding comple work as per direction by engineer. 284 G.S.T. Extra as per Applicable
