Tender For Miscellaneous Civil Related Work At Ac Officer Hostel Building (Block A, Block D) Eti Sarojininagar Lucknow, Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources 3 graded stone aggregate 20 mm nominal size derived from natural sources.( Based on DSR No-4.1.2) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources). ( Based on DSR No-4.1.4) Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources. ( Based on DSR No-5.1.2) Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.( Based on DSR No-5.9.1) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars (Based on DSR No-5.22.1) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand).( Based on DSR No-6.1.1) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand). ( Based on DSR No-6.4.1) Providing edge moulding to 18 mm thick Granite work counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work (Based on DSR No-8.3.2) Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Based on DSR No-8.31) Providing and fixing 250x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete . ( Based on DSR No-9.96.2) Providing and fixing200x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. ( Based on DSR No-9.97.3) Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15 mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.( Based on DSR No-9.99) Providing and fixing 125 mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete ( Based on DSR No-9.100.1) Providing and fixing Single Rubber aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. ( Based on DSR No-9.101.1) Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (Based on DSR No-9.21.1) Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete (Based on DSR No-10.25.1) Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).(Based on DSR No-10.28) Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete..(Based on DSR No-11.38) 12 mm thick plaster with cement mortar consisting of one part of cement & three part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material labour and T&P etc for proper completion of work. (Based on DSR No-13.4.1) 12 mm thick plaster with cement mortar consisting of one part of cement & six part of coarse sand(1:6),minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. (Based on DSR No-13.4.2) Providing and laying vitrified floor tiles in 600x600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.(Based on DSR No-11.41.2) Providing and laying Vitrified tiles in floor 600x600mm sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).(Based on DSR No-11.49.2) Providing and laying Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.(Based on DSR No-11.56.1) Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additivesNew work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.(Based on DSR No-13.48A.1) Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (Based on DSR-13.80 ) Wall painting One Coat with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.(Based on DSR No-13.83.1) Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (Based on DSR No 13.91) Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work. (Based on DSR No-13.99.1) Finishing walls with Acrylic Smooth exterior paint of required shadeOld work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface. Based on DSR No-13.111.1) Finishing walls with Acrylic Smooth exterior paint of required shade Old work (One or more coat applied @ 0.90 ltr/10 sqm). (Based on DSR No-13.111.2) Repairs to plaster With cement mortar 1:4 (1cement: 4 coarse sand) of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. (Based on DSR No-14.1.2) Providing & fixing White vitreous china water closet squatting pan (Indian type)( Orissa pattern W.C Pan of size 580x440 mm)along with S or P trap including dismantling of old WC seat and S or P trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.(Based on DSR No-14.80.2) Demolishing brick work in Cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (Based on No. 15.7.4) Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead.(Based on DSR No-15.12.1) Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm (Based on DSR No-15.23.1) Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (Based on DSR No. 15.56) Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (Based on DSR No-15.60) Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.(Based on DSR No-16.68) Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. Based on DSR No-16.82) Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.(Based on DSR No-16.83) Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in charge. (Old CC paver blocks shall be supplied by the department free of cost). (Based on DSR No-16.84) Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5 mm), including making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost. (Based on DSR No-16.85) Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.(Based on DSR No-16.89) Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia.(Based on DSR No-17.22B) Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.(Based on DSR No-17.31) Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.(Based on DSR No-17.81) Providing and fixing 15mm Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(Based on DSR No. 18.7.1) Same as above but for 20 mm dia.(Based on DSR No-18.7.2) Same as above but for 25 mm dia. (Based on DSR No-18.7.3) Same as above but for 50 mm dia. (Based on DSR No-18.7.6) Providing and fixing 15mm Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(Based on DSR No. 18.8.1) Same as above but for 20 mm dia.(Based on DSR No-18.8.2) Same as above but for 25 mm dia. (Based on DSR No-18.8.3) Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 20 mm nominal bore (Based on DSR No-18.18.2) 25 mm nominal bore. (Based on DSR No-18.18.3) Providing and fixing 65 mm gun metal gate valve with C.I. wheel of approved quality (screwed end). (Based on DSR No-18.17.5) Providing and fixing 80 mm gun metal gate valve with C.I. wheel of approved quality (screwed end). (Based on DSR No-18.17.6) Providing and fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (Based on DSR No-18.52.1) Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (Based on DSR No-18.53.1) Cleaning of main drain or width more than 300 mm.including disposal of waste refuses sludge out side the boards area including washing and cleaning by clean water completely as per direction of the Engineer-in-charge including cost of all labour,T&P etc.required for proper completion of the work.(Based on CSI No-20.14) Cleaning and opening of chocked W.C./ bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete.(Analysis based on NBO - 11 25.020.(Based on CSI No. 20.19) Cleaning of R.C.C. over head tank up to capacity of one lac. Liters and chlorinating with bleaching power mixed to water as per direction of Engineer - in - charge complete. NSI (Based on CSI No-20.27) Supply and mixing bleaching powder in over head tank as required or as directed by Engineer - in - charge.(Based on CSI No. 20.29) S/F of Jaquar make Pillar cock of model of FLR-5011N as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. (Based on CSI No-26.27) Supply and fixing of SS Bottle trap of make model no-ALD-769 L 250x190 as per direction of engineer in charge. This include cost of labour, material T& P etc for proper completion of works. (Based on CSI No-26.28) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) .( Based on DSR No-21.1.1.2) Providing and fixing aluminium work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron).( Based on DSR No-21.1.2.2) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) (Based on DSR No-21.3.1) Rewinding of burnt ceiling fan with approved copper wire including cost of all materials, labour and T&P etc. complete (Burnt wire will not be taken back.) (Based on CSI 22.08) Supply and replacing of burnt and damaged condenser of ceiling fan of approved quality including all materials,labour and T&P etc. (Based on CSI No- 22.09) Greasing of ceiling fan after cleaning the bearing and shaft with oil / petrol and its testing. (Based on CSI 22.11) Providing and fixing sun-film of Gareware or equivalent make on glass panes of door and window shutters including cost of all materials,labour and T&P etc. required for proper completion of the work. (Based on CSI No. 22.14) Attending to petty maintenance service like plumbing service,welder service, mansion service and carpenter service required as below.Job attending by one no. lumber/welder/mason/carpenter with one no. helper per hour or part of an hour.(Based on CSI No. 22.18) Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (Based on DSR No-22.50) Providing and fixing of 150 mm dia PVC pipe of 6 Kg/sqcm with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion ofwork. (Based on CSI No-26.25) S/F of Jaquar make Waste Coupling of model no ALD -705L130 as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. NSI (Based on CSI No-26.29) Supply and fixing of health faucet for model no-ALD-573 as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. NSI (Based on CSI No-26.30) Supply and fixing wall hung WS with normal closed seat cover for model no-CNS-WHT-959JSPP as per direction of engineer in charge This include cost of labour, material T&P etc for proper completion of work.NSI (Based on CSI No-26.31) S/F of Jaquar make Bib Cock of model no CON-047KN as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. . NSI (Based on CSI No-26.35) S/F of Jaquar make Towel Rail of model No. AQN 7711A 450 mm long as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. NSI Based on CSI No-26.36) Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials,labour and T&P etc.required for proper completion of the work. NSI(Based on CSI No. 27.19) Providing and laying 110mm SWR, PVC ( Finolex or equivalent ) pipe including cost of excavation, C.C etc including its jointing and connection, all materials, labour and T&P etc. required for proper completion of the work. (Based on CSI No-27.29c ) Providing and fixing SWR, PVC ( Finolex or equivalent ) Bends including cost of all materials, labourand T&P etc required for proper completion of the work. . (Based on CSI No-27.30c ) Providing and fixing SWR, PVC ( Finolex or equivalent ) Trap including cost of all materials, labourand T&P etc required for proper completion of the work. . (Based on CSI No-27.31c ) Providing and fixing SWR, PVC ( Finolex or equivalent ) Socket including cost of all materials, labourand T&P etc required for proper completion of the work. . (Based on CSI No-27.32c ) Providing and fixing SWR, PVC ( Finolex or equivalent ) Tee including cost of all materials, labourand T&P etc required for proper completion of the work. . (Based on CSI No-27.34c ) Providing and fixing ACP in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With ACP of 4.0 mm thickness (NSI Based on CSI -28.31) Supply and Fixing of 3 blade wall fan of Havells platina 400 mm or equivalent including all material, T&P etc required for proper completion of work as approved by engineer in charge.(Based on CSI No-28.33) Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge. (Based on CSI No-28.34) Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect.(Based on CSI No-28.35) S/F of jaguar make flushing plate model No. CHR 152415 for consealed cistern rate include cost of labour material T&P for completion of work.NSI (Based on CSI No-28.38) Supply and fixing of Jet Spray Model No-AHS-1557 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and filling cinder in sunken floor in 15 cm layers including cost of all labour and T & P etc required for proper completion of the work.(Bsed on CSI -22.92 2014) Supply and fixing of Rack bolt For WC Model No-ZPS-SNS-RB01 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Wax Seal Model No-ZPS-WHT-1401 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Providing and laying two coats of Pidifin 2K (Pidilite make) as per manufacturer’s Including supply of all materials, labour and T & P etc required for proper completion of work. (NSI) (Approved Rate by Analysis) Supply and fixing of Concelled cistern with wall mounting frame & instalation kit Model No CHR-159415 2400WS with control plate lemon design Model No-JSP-CHR-152415 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Two way Bib cock with wall flange Model Noopp-15041PM of Jaquar make or equivalent. make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Cistren Base Plate Model No- ZMP - CHR-003 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Cistren Ball Cock Model No- ZMP - CHR-002 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Cistren Syphon Model No- ZMP - CHR-001 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Conector Pipe Model No- ZPS-WHT-VB01 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work .NSI (Approved Rate by Analysis) Supply and fixing of Brass Inlet Fixing Model No- ZPS-BRC-5007of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work . NSI (Approved Rate by Analysis) Supply and fixing of Rubber Gasket Inlet & Outlet Model No- ZPS-WHT-GK01 of Jaquar make as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work . NSI (Approved Rate by Analysis) Providing & Making & Fixing of Wall Pannelingas on damaged surface The surface cladded with 6mm Water Proof & Fire Retardent ply fitted with the help of nails sulution on wall surface as per the approved design all complete as per drawing, specification and direction as approved by the Architect/ Engineer -in-Charge. NSI (Approved Rate by Analysis) Providing and fixing superior,approved quality cotton curtain height approximately 2.65mtr upper side margin 0.05mtr, lower side margin 0.02 mtr, upper side margin fitted proper tape for hanging curtain with the help of hooks and rings at DIFFRENT cabin of Shakti Bhawan Extn, Lucknow as per direction of Engineer in charge. The work includes cost of all labour, material and T&P etc.NSI (Approved Rate by Analysis) Supply and fixing galvanised mosquito proof jali (16x24 gauge) with M.S. flat of 20 x 3 mm. size, on both sides screwed or welded to window or door frame.NSI (Based on CSI No. 9.18) Supply and fixing brass polished hydraulic door closure of approved make & quality its fixing and adjustment with the help of screws, nuts and bolts including supply of all labour, T & P etc. required for proper completion of the work. (CSI No. 8.57) Providing and fixing in place a full height storage cabinet 450 mm deep made with 19 mm thick ISI marked ply borad, all interior surfaces to finished with pasting of 0.8 mm thick mica and all exterior surfaces to be finshed with pasting of 1 mm thick mica of texture and colour as approved by Engineer in Charge including all labour, T&P, other items like (but not limited to) fevicol, nails screws, higes, sliders,door handles, multipurpose lock of godrej or equivalent rate etc. required for proper completion of works, to be measured interms of front area only.NSI (Based on CSI No. 8.62) Applying BIRLA PUTTY or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ICI or equivalent brand for smoothining and leveling of the surface as per requirement and direction of E/I including cost of all material , labour and T&P required for proper completion of work. NSI (Based on CSI No.13.21) Providing and fixing Plastic seat cover Cpmplete with Plastic Lid For Europian type WC ISI Marked including supply of all materials,labour and T&P etc.complete. NSI (Based on CSI No. 27.04) Providing and fixing CP BRASS SHOWER HEAVY QUALITY ( > 225 gms ) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI (Based on CSI No. 26.16e) Repairng of old cushioned Sofa (01 seat )removing of old damage upholstery then wooden frame repairing and re-polishing, upholstery of new 75 mm thick sleepwell foam 32 denstry on seat and back side of Sofa using 50 mm thick sleepwell foam 32 denstry, Approved. The work include cost of all labour,material T&P required for proper completion of work.NSI (Analysis Enclouse) Supply and fixing PVC Nahani Trap India make of heavy approved quality complete with CI grating, including supply of all materials,labour and T&P etc. required for proper completion of the work. NSI (Based on CSI No. 27.21b)
