|
| 1 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. (a) In cement mortar |
| 2 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 3 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : (a) Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 4 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. (a) Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 5 | 12 mm cement plaster of mix : (a) 1:6 (1 cement: 6 coarse sand) |
| 6 | 15 mm cement plaster on the rough side of single or half brick wall of mix : (a) 1:6 (1 cement: 6 fine sand) |
| 7 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge. (a) With cement mortar 1:4 (1cement: 4 coarse sand). |
| 8 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. (a) 110 mm diameter |
| 9 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. (1) Single tee with door (a) 110x110x110 mm |
| 10 | (2) Bend 87.5° (a) 110 mm bend |
| 11 | (3) Shoe (Plain) (a) 110 mm Shoe |
| 12 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall (a) 20 mm nominal outer dia. Pipes. |
| 13 | (b) 25 mm nominal outer dia .Pipes. |
| 14 | (c ) 40 mm nominal outer dia. Pipes. |
| 15 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : (a) 15 mm nominal bore. |
| 16 | (b) 20 mm nominal bore. |
| 17 | © 25 mm nominal bore. |
| 18 | (d) 40 mm nominal bore. |
| 19 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : (a) 25 mm nominal bore |
| 20 | (b) 40 mm nominal bore |
| 21 | Providing and fixing PTMT bib cock of approved quality and colour. (a) 15mm nominal bore, 90 mm long. Weighing not less than 93 gms. |
| 22 | Providing and fixing PTMT stop cock of approved quality and colour. (a) 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 23 | Providing and fixing PTMT pillar cock of approved quality and colour . (a) 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 24 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 25 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. (a) 10 litre capacity - White |
| 26 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \"S\" or \"P\" trap including dismantling of old WC seat and \"S\" or \"P\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. (a) Orissa pattern W.C Pan of size 580x440 mm |
| 27 | Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. |
| 28 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 29 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (a) Semi rigid pipe (ii) 40 mm dia |
| 30 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. (a) 15 mm nominal bore with 45 cm length. |
| 31 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : (a) For fixed portion (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 32 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 33 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. (a) Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 34 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (a) With float glass panes of 5.00 mm thickness (weight not less than 12.5 kg/sqm) |
| 35 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :(a) 300x16 mm |
| 36 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : (a) 300x10 mm |
| 37 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : (a) 125 mm |
| 38 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper |
| 39 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 40 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : (a) Old work (One or more coats) |
| 41 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : (a) One or more coats on old work. |
| 42 | Providing and fixing steel clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs/PVC gullly, screwed with M.S. screws of required length all complete as per direction & satisfaction of E-I-C. for 110mm dia RWP. |
| 43 | Fixing aluminium work for doors, windows, ventilators and partitions with availabledismantledextruded built up standard tubular sections/appropriate Z sections and other sections , fixing with newdash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sidesand fixing dismantled glass/board in required size by cutting with required newEPDM rubber/neoprene gasket etc.includingnew cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws wherever required, all complete as perdirections of Engineer-in-charge. |
| 44 | Dismembering ofrain water supply line(RWP 110mm) and refixing the same to avoid the seepage and proper arrangement i/c changing ofruber etc as required at siteup to 12.00 mtr height including all operation scaffolding etcall complete as per direction & satisfaction of E-I-C |
| 45 | Cleaning of chowkage of water supplyLine( 15mm to 40mm ) by dismembering of water supply line and clearing by Roding camping etc and re-fixing the pipe i/c Necessary fixtures like nipple ,bracket etc.As per direction & satisfaction of E-I-C |
| 46 | Cleaning of glazed tiles of toilet & bath room, wash basin, kitchen etc. with hypo (oxalic) Acid /chemical to remove oily depositors and finaly wash with clean water etc.allcomplete as per direction& satisfaction of E-I-C |
| 47 | Repairing of cistern by replacing complete internal fittings / fixtures and ball cock ,complete as required. |
| 48 | Refixing wash basin or Kitchen sink by new G.I pipe or CI bracket and making the walls.All complete as per direction & satisfaction of E-I-C |
| 49 | Providing & fixinghomogeneous Antistatic sheet and skirting of approved company like Krishna Vinyl, wonder Floor etc.in approved pattern on a smooth and damp proof base using rubber equivalent adhesive of approved quality and manufacture like Dunlop- S-758, Fevicol SR-998 or I/c rolling with light woodenroller weighing about 5 kg,i/c repairing of damaged floor where ever necessary all complete as per direction of E.I.C (a) 2.00mm thick sheet |
| 50 | Providing & fixing copper strips 20X.0.30 mm thick below antistatic flooring as per direction of E/I. |
| 51 | Cleaning of water tank (RCC or PVC) up to floor five level of capacity 500 to 1000 liter i/cdewatering and removal of all sludge deposits and finally disinfecting with bleaching powder and date of cleaning written in bold letter with synthetic enamel paint. All complete as per direction & satisfaction of E-I-C |
| 52 | Credit value of dismenteled Brick |
