tender for Tourism Development Work Of Amriteshwar Nath Shiv Mandir At Payagpur, Distt.-Bahraich, Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T & P rtc required for proper completion of the work and curing complete also including cost of formwork in foundation & floors. Filling of earth in plinth in 20cm layer including leveling, dressing and watering and also including of supply of earth including carted loading & unloading as per direction of Engineer lincharge.. Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources 3 graded stone aggregate 20 mm nominal size derived from natural sources) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 150 in super structure above plinth level up to floor v level in all shapes and size in:1:4 (1 cement: 4 sand) Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately): Red sand stone - Exposed face machine cut and table rubbed with rough backing. 50 mm thick T.M.T.-FE-500 steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage & over lapping & hooks. Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand), including making the necessary chases. Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement mortar 1:6 (1 cement: 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade. Red sand stone Supply fabrication transporting, hoisting and fixing in position good quality of 70mm Red sandstone in various elements for all levels, stone shall be free from cracks, lines stains and even in shade for each element The The stone shall be fine grained and reddish or buff-colored (locally available). The work shall be carried out as per attached drawings with different process of ie carving (manual/ by machine), ornamental work, traditional work, figure work (any type, any size), CNC cutting, moulding. The carving and molding work Shall be of very good quality. The stones to be fixed in line, level and plumb in all respect with the use of brass clamps, pins, (to be paid separetely) dowels, cement slurry with matching pigment and Epoxy of Akemi Germany, Ardex Endura, MYK laticrete or approved make as required and as approved by the Architects Supply fabrication & fixiing,in position ornamental Jharokha of cement concrete of size 500 mm x 700 mm & 200 mm wide. Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement: 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources 3 graded stone aggregate 20 mm nominal size derived from natural sources). Treatment of soil under existing floors using chemical emulsion @one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sand filling in plinth under floors including watering, ramming, consolidating and dressing complete including lead up to 50m and lift upto 1.5m and including cost of sand, Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand 4 graded stone aggregate 12.5 mm nominal size). Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 150 in sub structure below plinth level in all shapes and size in:1:6 (1 cement: 6 sand) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 150 in super structure above plinth level Jup to floor v level in all shapes and size in:1:6 (1 cement: 6 sand) Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in- charge. 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a PVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 10.1 mm) wall thickness. The lock rail made up of H section, a PVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. U cleats. The shutter frame filled with a PVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers. complete, aa Monitoring all complete as per approved drawing & direction of E Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever (required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm, sash 67 x 80 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm). Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings wooden frames with rawl plugs screws etc. 15 mm cement plaster of mix: 1: 4 (1 cement: 4 coarse sand) 12 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand) Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement: 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. Red sand stone Cement concrete flooring 1:2:4 (1 cement 2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (25 mm thick floor). Providing and laying Vitrified floor tiles Kajariya KERRO Brand Jor Equivailent brand of super quality in different size (thickness specified by manufacture) with water absorption less than 10.80% and confirming to IS 15622 of approved make in all colors & shade laid on 20mm thick cement mortar 1:3 (1 cement 3 coarse sand) including grouting the joint with white cement and matching pigments etc complete (Size of tiles 600x600mm) [Skirting] 25mm Thick Kota Stone Slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mix with pigment to match the shade of slab includig rubbing and polishing complete with base of cement morter. 25mm Thick Kota Stone Slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mix with pigment to match the shade of slab includig rubbing and polishing complete with base of cement morter. Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water tinnable priming coat with cement primer Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 Itr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).. Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Painting Steel work with Deluxe Multi Surface Paint to give an leven shade. Two or more coat applied @ 0.90 tr/10 sqm over Jan under coat of primer applied @ 0.80 Itr/10 sqm of approved brand and manufacture Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in- charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement:5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (C) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 120 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, windowsills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm (Granite of any shade) Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) Red sand stone exposed face fine dressed with rough backing. 50 mm thick Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a) White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap. Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Providing and fixing rubbed stone slab table, edges rounded and polished, 75 cm high 50 cm deep and 18mm thick, fixed in Jurinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite stone of approved shade roviding and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge 15 mm nominal bore Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in- charge Providing and fixing CP BrassToilet Paper Holder of approved quality & make and as per the direction of Engineer-in-charge Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Providing and fixing rubbed stone slab table, edges rounded and polished, 75 cm high 50 cm deep and 18mm thick, fixed in Jurinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite stone of approved shade roviding and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge 15 mm nominal bore Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in- charge Providing and fixing CP BrassToilet Paper Holder of approved quality & make and as per the direction of Engineer-in-charge Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Providing & fixing baby Stainless Steel Baby Diaper cahnging station material unit dimensions depth (closed) VW-905 mm x H- 502 mm extension (open) 104 mm, 495 mm. Maximum load 25 Kgs Stainless steel #304 stain finish complete with all accessories & fittings as per drawing, bybo design, W00008 set- weisis (Euronics/Cera/Jaquar/Kohler/Toto or equivalent) Supply & fixing of CP soap tray fixed to the wall with PVC rubber plug with CP barss screws Make - Hindware, Model- F840004 Supply & fixing of CP brass plated health faucet with double lock 1.5 m long flexible hose with mounting bracket Make - Hindware, Model-F160002 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.J. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand 4 graded stone aggregate 20mm nominal size) i/c necessary excavation, foundation concrete 1:5:10 (1 cement: 5 fine sand 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay F.P.S.(non modular) bricks of class designation M-15 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 50 to 80 mm nominal bore Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore Providing and fixing G.I. pipes complete with G.l. fittings and clamps, i/c cutting and making good the walls etc.(Internal Work) 32 mm dia nominal bore. (medium duty) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes CPVC 25 mm nominal outer dia Pipes Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion(i) Single socketed pipes. a) 110mm diameter Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement 4 coarse sand) and making good the wall etc. complete. a) 110mm Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc. (internal work) Exposed on wall a) 25mm dia nominal bore (medium duty) Providing & fixing CP brass short body of approved quality conforming to IS 8931 a) 15mm nominal bore Providing and fixing gun metal gate valve with wheel of approved quality. 25 mm nominal bore Providing and fixing gun metal gate valve with wheel of approved quality. 50 mm nominal bore Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete b) 25 mm nominal bore Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. a) Circular Tank Providing and fixing square mouth UPVC S.W.R. Gully trap grade A complete with C.I. grating brick masonry chamber with F.P.S. bricks of class designation 75 and water tight C.I. cover with frame of 300 x 300mm. size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design.a) 150 x 110 mm. size P type With Sewer bricks conforming to IS: 4885 Constructing brick masonry manhole in cement mortar 1:4 (1) cement:4 coarse sand) RCC top slab with 1:2:4 mix (1 cement 2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement 4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement:2 coarse sand 4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80X50cms including Cl cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg) With FPS bricks of class designation 150 (i) For Sewer Line extra for depth of man hole size 90x80 cm Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 gradded aggregate of nominal size 20mm) as per standard design with 20x20mm sq bars. Providing & fixing centrifugally (cast spun) 100mm dia vent pipes, Providing & fixing centrifugally (cast spun) 75mm dia vent pipes. Providing lead caulked joints to sand cost iron/ cetrifugally cast (squn) irons pipes & fitting of dia. 100 mm Providing lead caulked joints to sand cost iron/ cetrifugally cast (squn) irons pipes & fitting of dia. 75 mm Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc.: For 100 mm dia pipe For 75 mm dia pipe Providing & fixing Cost iron coller: 100 mm dia Providing & fixing Cost iron coller: 75 mm dia Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet 75 mm outlet Providing and fixing plaincast iron ss sanitary bend; 100 mm Providing and fixing plaincast iron ss sanitary bend; 75 mm Providing and fixing centrifugaly cast iron single eual plai junction of reuired degree: 100x100x100 mm Providing and fixing centrifugaly cast iron single eual plai junction of reuired degree: 75x75x75 mm Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) all-round S.VV. pipes including bed concrete as per standard design: 110/75 mm dia 150 mm dia Providing and fixing G.l. pipes complete with G.l. fittings & clamps including cutting & making good the wall etc. internal work exposed on wall 25 mm dia nominal bore Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality 25 mm nominal dia bore Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil 80 mm dia but not exceeding 300 mm dia. Providing, laying and jointing glazed stoneware pipes class SP- 1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete 100 mm dia. Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete: 150 mm dia. R.C.C. pipe Providing & fixing gun metal non return valve of approved quality (screwed End) 50 mm nominal bore vertical Providing & Fixing G.I. pipes complete with G.I. Fittings including trenching & refilling etc. 25 mm nominal bore Providing & Fixing G.I. pipes complete with G.I. Fittings including trenching & refilling etc.32 mm nominal bore Providing & Fixing sand of grading zone V or coaser grade alround the G.I. pipe in external work 25 mm dia. Providing & Fixing sand of grading zone V or coaser grade alround the G.I. pipe in external work 50 mm dia.. Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Providing & fixing ridges and hips in non-asbestos fibre cement high impact polypropylene reinforced roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc.complete. Corrugated serrated adjustable ridges. Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer- in-charge) 0.50 mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever reuired. Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m² Providing and fixing decorative cast iron corner bracket of size 300x300 having weight not less than 9.2 Kg.including the cost of machine moulding or any other suitable medium as reuired with respect to the drawing received from Architect in charge. Providing and fixing of sky light polycorbonate sheet 3.0 mm thick sheet, colour Transparent Transparency 80% features water proof surface treatment film coated (size, shape and pitch of corrugation as approved by the Architect-in-charge) size and shape whereever reuired. Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately): Red sand stone exposed face fine dressed with rough backing. 70 mm thick Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. In all kind of soil. From 0.00 to 1.50 Mt. 11.50 to 3.00 Mt. Fe 500 Mild steel or iron work of small sizes and sections such as holding down bolts, hold fasts, tie, rods, grating etc. ( when not included in an over all rates) wrought to required form, including supply of steel bolts, nuts and wastage etc and their fixing required for proper completion of the work. 12 mm cement plaster of mix: 1: 4 (1 cement: 4 coarse sand) Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part 1), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level Rocky strata including Boulders.350 mm dia Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.150 mm nominal size dia Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia Gravel packing in tubewell construction in accordance with IS: 14097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. Development of tube well in accordance with IS: 2800 (part 1) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by V notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of:150 mm dia Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part 1), including necessary bolts & nuts of required size complete.150 mm dia Providing and fixing Bail plug/Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part 1).150 mm dia Providing and fixing G.I. pipes complete with G.l. fittings including trenching and refilling etc. 50 mm dia nominal bore Providing and fixing 150 mm S.C.I. tee at the inlet and outlet of septic tank. Providing & fixing 75mm dia vent pipes. Providing & fixing of 75mm dia cast iron terminal guard. Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 560mm internal diameter Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.VV. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 150 Electric logging of bore hole Supply and Installation of 1.5 HP Submersible pump set complete Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. Supply and fixing of 80 mm thick Precast cement concerete and Fly Ash Zig Zag-Shape rubber moulded Interlocking paver blocks ISI mark confirming to IS 15658-2006 with top layer of minimum 5 mm thickness of O.P.Cement smooth high gloss finish, skid resistant; manufactured from rubber moulds through vibro-compression mechanism. The compressive strength of concrete paver block shall not be less than 30 Mpa and weigt 4.5 kg per including cost of material, with a blanket layer of 5.00 cm. thick local sand including labour, T & P etc required for proper completion of the work as directed by Engineer-in- charge. 40 mm thick rubbed stone flooring over 20 mm (anerage) thick base of cement mortar 1:5 (1 cement: 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement: 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red sand stone Providing & fixing of red Sandstone/MS bench with Ornainentetion on armrest (size 1050mm length and 450mm and height 450 mm) induding oundation & support with all necessary T&P etc all complete as per design of direction in engineer/Architect in charge. Providing & fixing of SS Dustbin size 487 x 399 x 1138 fixing on la foundation with base plate and wrapped with red andstone from all sides of 75mm with all complete as per design of direction in engineer/Architect in charge. Providing and fixing StandAlone Signage in Marble of approved thickness with powder coated 10-12mm MS letters and iBustration at desired locations with letters (in english, hindi and Braille)- ehed, through cut, infilled or painted, also including the ost of design, fabrication and onsite installation with an the necessary accessories and equipments for fixing on any surface as per drawing and design approved from Architect in charge English: Helvetica Font with min. 36 size Hindi: Krutidev Font with min. 36 size Signage-A Informative Sinage of Sandstone/ Marble of Size (1200 x 2100) MM visibility from both side Signage-C Informative Sinage of Sandstone/ Marble of Size (900 x 2400) MM visibility from both side Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). Supplying and stacking of good earth at site including royalty but including carriage 1km (earth measusred in stacks will be reduced by 20% for payment) Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment): Screened through sieve of I.S. designation 16 mm Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge.. Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/or good earth to be paid separately). Rough dressing the trenched ground including breaking the clods. Fine dressing the ground Grassing with selection No.1 grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and the good earth shall be paid for separately). With grass Turf. Uprooting weeds from the trenched area after 10 to 15 days after flooding with water including disposal of uprooted vegetation Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly, as per direction of officer in charge (Selection No. 1) Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20%: 1 part of stacked volume of manure after reduction by 18%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately): Holes 90 cm dia, and 90 cm deep Preparation of beds for hedging and shrubbery by excavating 60 cmdeep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 18%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable materials as per direction of officer in charge (excluding cost of plant & water) Providing and stacking of Acacia auriculiformis of ht. 150-165 cm in bag size of 25 cm as per direction of the officer-in- charge. Providing and stacking of Adansonia digitata (kalp vriksha) of ht. 150-165 cm in bag size of 25 cm as per direction of the officer-in-charge. Providing and stacking of Bombax ceiba of ht. 150-165 cm in poly bag size of 25 cm as per direction of the officer-in-charge. Providing and stacking of Bottle palm of ht. 150-165 cm bottom girth 20-25 cm well developed in big in poly bag size of 25 cm Jas per direction of the officer-in-charge. Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big in HDPE bags as per direction of the officer-in-charge. Providing and stacking of Azadirachta indica (Neem) of ht. 120- 130 cm in big in poly bags of size 25 cm as per direction of the officer-in-charge. Providing and stacking of Tulsi of ht. 30 cm with multi branches in big in poly bags of size 20 cm as per direction of the officer- in-charge. Providing and stacking of Phyllanthus (Amla) of ht. 150-165 cm in big in HDPE bags as per direction of the officer-in- charge. Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer-in- charge. Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer Gl pipe of 16 swg and inner Gl pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm G.l. strip, upto switch board (from apron to switch board, the cost of G.l. strip will be extra) along with 30 cm square C.l. frame with hinged cover & masonry housing Make: As approved in U.P.P.W.D., & C.P.R.I. Certified Supply and laying of 25mm x 3mm G.l. strip from earth electrode directly in the ground as required complete in all respect. Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sq. mm 4 core 25 sq. mm 3-1/2 core 170 sq. mm 3-1/2 core Supplying and laying of following size owe HOPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming tolS 14930, Part II complete with fitting and cutting, Jointing etc. Jn the existing trench complete as required. 63 mm dla (OD-63 mm & D-51 mm nominal) Supply, Installation, Testing and Commissioning of LED RGB/RGBW floodlighting luminaire for facade lighting with Die- cast aluminium housing, powder-coated finish, of following wattage. Luminaire shall be capable of producing dynamic color changing light for with 16 million colors by DMX/Ethernet based control. The beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100-270 V AC, 50 Hz with power factor > 0.9 Fixture shall be suitable to operate at an ambient temperature range of 10°C to +50°C and shall be IP 65 and IK 06 rated. Lifetime shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS (IS 10322) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.30V Supply Installation, Testing and Commissioning of ongrid Solar Photo voltaic Power Plant conforming to MNRE specifications as amended, consistingofMono/PolyCrystallinesiliconsolarcells,net meteringfacility,necessaryprotections, earthing, mounted on Aluminium/Gl structure of suitable strength with following componentscompleteasrequired: a) Solar PhotovoltaicModuleofca pacity330VVporabove, manufacturedinIndia, conformingtolS1428 БЛЕС61215, ISMEC61730-Part-1, ISMEC61730-Part- 2.SolarPhotovoltaicModuleconversionefficiencyshallnotbelessth an16.5%.PVmodules usedinsolarpowerplants/systemsmustbewarrantedfortheiroutp of 2.5Hz,output voltagesuitabletogenerateAC utpeakwattcapacity, whichshouldnotbelessthan90%attheendof 10yearsand80% atthe end b)PowerConditioning Unit (PCU)of350 800VDCInputvoltagerangeand400V threephase, 4wire, 50Hz+/- Powerwithefficiencynotlessthan97%,totalharmonicdistortionles sthan3% suitableforambienttemperaturefrom0to50degreeC.TheP CUshalladjustthe voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) FixingofArray junctionbox&Main junctionboxwith IP65protectionand terminationarrangement for incomingandoutgoingcablealongwithglands, lugs and other accessories etc. as required, e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kVgrade armouredpower and control cables between solarmodules, mainpower cable togrid supplyPCUunit alongwith supplying&fixingofnecessarychannel/conduit lugsandotheraccessoriesetc.as required. 25 years. AC, Supply, Installation, Testing and Commissioning of LED RGB/RGBW floodlighting luminaire for facade lighting with Die- cast aluminium housing, powder-coated finish, of following wattage. Luminaire shall be capable of producing dynamic color changing light for with 16 million colors by DMX/Ethernet based control. The beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100-270 V AC, 50 Hz with power factor > 0.9 Fixture shall be suitable to operate at an ambient temperature range of 10°C to +50°C and shall be IP 65 and IK 06 rated. Lifetime shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS (IS 10322) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. 40VV Supply and Fixing of Spike Light for trees 12 watt Warm White. 31386 12VV Anthracite COB Garden Spike 30 (make (Philips/Panasonic/Havells or Eauivalent)) Supply and fixing of steplignt robus T DESIGN IP 67/1K 10 easy to mount with suitable mounting box BVVG 50 LED 50 /N/WPSU 220-240 V IP67 7043 (Philips/Havells/Panasonic or equivalet) Supply and fixing of LED Bollard robustly designed IP65/KL-7062 8112W LED WWW.NW.C/W, Clear Polycarbonate 0100 X 900mm M2 (Make Twinkle 1Qlite/Havells/Neri/Juvaas/Olient/Thor orequivalet) Lite- Receiving, storing, handling, shifting, installation, testing & commissioning of WAE. AENON.45.CHA For Wire Station C.A, RO Processing Capacity 25LPH, size: 466X580X1445, Watt; 220v/50Hz, Cooling 480w, Hot 450W, net weight 110kg, in material SS 304, with 3 tap: Cold 20 Ltr, Ambient-25Ltr including all accessories complete in all respect etc.(Make Voltas or Equivalent) Wiring point for light with 1.5 sq. mm.FR PVC insulated multistrand single core copper conductor cable in PVC conduit pipe with 1.5 sq. mm FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduit partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete Modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash Wiring point for Exhaust Fan with 1.5 sq. mm. F.R. PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduit partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete Modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash Wiring point for plug with 1.5 sq. mm. F.R. PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduit partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete Modular type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash Supply and fixing of recess/ Surface/Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set complete in all respect. CAT-AAA Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer Gl pipe of 16 swg and inner Gl pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.1, strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. Supply and fixing of recess/Surface/Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and Idriver set complete in all respect. CAT-AAA Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (b) 10sq. mm 2 core Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect, The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. (b) 10sq. mm 2 core Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. (c) 10 sq. mm Supply and fixing of Two number 8 SVG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. S&F of 6 Amp to 32 Amp. SPMCB (10.KA) C Curve CAT-A S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve 32. Amp. DP MCB (10KA) CAT-A Supply and fixing of crimping, solderless, copper tin electroplated lugs of Dowells/Ismail make suitable for 1.5 sq.mm to 2.5 sq.mm cables, including tapping with insulating tape, complete in all respect. S&F single pole MCB blanking plate CAT-A S&F surface/flush mounting 8ways SPN distribution board with additional metal door without MCB complete in all respect, as directed by Engineer in charge. CAT- A Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc., complete in all respect. Supply and fixing of 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect. Supply and fixing of single phase multifunctional electronic energy meter 10 to 60 Amp. capacity fitted in integral box on wall complete in all respect. Supply of 225/230mm sweep ventilating (Light Duty) exhaust fan complete with Metallic Blade (Steel bird guard protector /Copper motor for high air suction performance /Capacitor etc.), Noise level: (4550) dB, Power consumption: 45 W, Rated voltage: 230 V, Rated frequency: 50 Hz, Motor type: Normal Speed. Complete in all respect. 230 mm sweep Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SVVG copper earth continuity wire, GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash Wiring point for two ways light with 1.5 sq. mm. F.R. PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SVVG copper earth continuity wire, GP Box and two number two way piano type switches & ceiling rose / angle / batten holder on 3 mm thick phanolic laminated backelite sheet etc., complete in all respect, as directed, including matching colour wash. Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SVWG copper earth continuity wire, GP Box, piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash. Wiring point for plug with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with14 SVVG copper earth continuity wire and piano type switch and socket etc., complete in all respect including matching colour wash. Wiring point for exhaust fan with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SVVG copper earth continuity wire, GP Box, 15A piano type switch & ceiling rose on 3 mm thick phenolic laminated backelite sheet etc., complete in all respect including matching colour wash. Wiring point for light in 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable (drawn through existing concealed steel conduit) and 5 Amp.flush type switch & ceiling rose/angle/batten holder fixed with 3mm thick phenolic laminated backalite sheet with brass machine screws and cup washers mounted over existing M.S. switch board box/junction box with supply of all material, labour & T&P etc. required for proper completion of the work as directed at site by the Engineer in charge.but for plug point with 5 Amp flush type switch and 3 pin socket and earth continuity wire of 1.5 sq.mm. FRLSH PVC insulated multi strand copper conductor cable. Add for light / fan points with modular type switch in place of piano type switch. Add for 2 way light point with modular switches in place of piano type switches. Add for plug point with modular switch & socket in place of piano type switch & socket. Add for HPMV/Exhaust fan point with modular type switch in place of piano type switch. Supply and wiring of submain with two number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with one no. 14 SWG copper earth continuity wire etc, complete in all respects including matching colour wash Supply and wiring of submain with two number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit partly laid in slab alongwith reinforcement before concreting and partly concealed in wall, with one no. 14 SWG copper earth continuity wire etc, complete in all respects including matching colour wash. Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with one number 14 SVVG copper earth continuity wire including matching colour wash etc. complete in all respect. Supply and wiring of submain with two number 6 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core aluminium conductor cable in 20 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with one number 14 SVVG copper earth continuity wire including matching colour wash etc. complete in all respect. Supply and wiring of 4 number 6 sq.mm. FRLSH PVC insulated 1100V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with two number 14 SVVG copper earth continuity wire including matching colour wash etc, complete in all respect. Supply and wiring of 4 number 10 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 32 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with two number 10 SWG Icopper earth continuity wire including matchina colour wash etc, complete in all respect, Supply and fixing of batten / angle holder complete in all respect. Supply and fixing of recess mounting round 15 to 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AAA Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. Supply and fixing of 3 Watt to 6 Watt LED Spot/Spike light luminaire Confirming to IP 66 Protection complete in all respect. CAT-AAA Supply of ceiling fan with fan motar of A.C. permanent insulation, capacitor rating conforming and IS: 374/79 and also comply with IS;1709//1984 with latest amendment. The rated voltage 220/240 volts, 50 Hz, 1-ph AC the fan assemble should consists of down rod blades, shackle canopies etc and with doubble ball bearing system. BEE 5 star rated -1200 mm sweep Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. (j) 25 sq. mm 3-1/2 core Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. (e) 25 sq. mm Supply and burring of Safe Earthing Electrode T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal Dia 12 mm, coating 80-100 micron filled with. crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 x 3 G.J. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCBs (Four Pole 36 KA with thermal magnatic release)Switches Complete and instrument chamber etc.complete in all respects, The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters(KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCBs shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. Thea Monitoring System complete with accessories. d) FixingofArray IP65protectionand junctionbox&Main junctionboxwith terminationarrangement for incomingandoutgoingcablealongwithglands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kVgrade armouredpower and control cables between solarmodules,mainpower cable S&F of 63 Amp. 4 pole MCB(10 KA) C Curve CAT-A S & F surface/Flush mounting 4ways TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. CAT-A S & F surface/Flush mounting 6ways TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge CAT-A Supply and fixing danger board fabricated from 10 gauge M.S. Sheet as per I.E. Rules. Erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick G.I.Pipe19mm dia. Duly painted, complete in all respect. Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work. Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality. Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 A/250 volt flush type universal modular socket switch on concealed M.S box including supply of all material, labour T&P etc. required for proper completion of work. Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. Supply and fixing of electronic fan regulator(Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.. Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 1 or 2 Module Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 3 Module Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 4 Module Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 6 Module Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 8 Module Supply and fixing following modular base & cover plate on the existing modular /GP boxes etc. as required. 12 Module Supply & Fixing of 12 Watt LED Bulb -B22/E27 (Colour Temp- 6500K/ Lumenes -900 Im) cool day light/ input volts (Ac 90 V- 260V, 3-star rating, suitable for batten/angle holder including making Connection in all respect. Supply & Fixing of 400 mm sweep wall mounnted (Light Duty fan complete with Plastic Blade & Pull Cord (Adjustable upward & downwword tilt mechanism/motorcapcitor etc.) Oscillation degree-90, Power Consumption, 60VV, Rated voltage: 230 V Rated Freuency:50 Hz, Speed 1350 RPM complete in all respect..
