Tender For Special Repairs Of Bldg No T-39 (Jcos/Or Living & Stores) And Other Rev/Minor Works At Naaunder Ge (North) Tezpur.; 1 Dismantling of Asbestos cement(corrugated, semi corrugated etc.) sheet in roof coverings complete all as specified and as directed. 2 Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water etc, complete all as specified and as directed. 3 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed 4 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed 5 Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed. 6 M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed. 7 M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed. 8 Supply and Fix exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 4mm dia GI wire as suspender and including 4mm thick decorative pre -painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantling of existing false ceiling boards, complete all as specified and directed. 9 M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc13 sq.cm & n exc 25 sq.cm)as in studs of ceiling / sunshed./truss members complete all as specified and directed. 10 Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed. 11 M & L for cement concrete in foundation, filling and mass concrete in M15(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed. 12 M&L in repair for second class HW scantalling, wrought, in any position for framed work , jointing with necessary nails, nut bolts etc including necessary supports for truss structure complete allas specified and directed. 13 M&L for 18-20mm thick machine cut kota stone slab flooring of size not less than 500x500mm over and including 20mm thick cement mortar (1:6) cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed 14 M&L for 18-20mm thick machine cut kota stone slab flooring of size not less than 500x500mm in riser of steps, skirting, dado and pillar over and including 15mm thick cement mortar (1:4) cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed 15 M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. 16 M&L for preparation of old decorated wooden surfaceswith pre mixed wood filler used as putty of grith exc 10cmand applying two coats of synthetic enamel paint complete all as specified and directed. 17 Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge 18 Preparation of old or previously untreated steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. 19 M&L for preparation of new plastered or undecorated surfaces of wall/ceiling using wall care putty to fill the voids and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed. 20 M&L for preparation of old decorated surfaces of wall after complete scrapping down and using wall care putty to fill the voids and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed. 21 M&Lfor preparation ofnew surface of plastered wall using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller overincluding one coat of alkali resistant priming paint before distempering complete all as specified and directed. 22 M&L for preparation of old decorated surfaces including washing, rubbing down and stopping of white wash surfaces of walls (Plastered or un-plastered) including cormices pilasters etc and using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller including one coat of alkali resistant priming paint before distempering complete all as specified and directed. 23 S&F 18-19mm block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including necessary leaping/edge margin of 3mm thick with decorative face veneer on both faces complete in all respect as specified and directed. 24 M&Lfor 75 mm thickcement concrete 1:3:6type C-2 (using 40 mm graded stone aggregate) as in path /steps laid with and incl use and waste of form workand finishing the surface even and rough to receivethe topping layer ortiling complete all as specified and directed by engineer-in-charge. 25 M & L for granite work (of any type) 18-20mm thick machine cut, over and including 15mm thick cement mortar (1:4)screed base laid and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. 26 M & L for 18-20mm thick granite work (of any type) machine cut, in skirting/dado laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed 27 M & L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. 28 M & L for powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 no.). hinges type B-21 100 mm long (2 no.) suitable handle (1 no.) complete all as specified 29 M&L for anodised aluminium grill for doors, windows, ventilators including joining cleat for fixing etc. complete in all respect as specified and directed. 30 S & F powder coated aluminium ventilator with half portion louvered (adjustable)with 4mm thick glass in louver and balanced portion fixed 4mm thick frosted glass glazing including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete in all respect as specified and directed. 31 S&F 30mm thick second class HW glazed andskeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars),edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters as specified inSSR Part I, Section 8, clause 8.24(a) complete allas specified and directed. 32 S & F flush door shutters, 30 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed. 33 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixing with beads in door/window/ventilator/fixed glazingshutters complete allas specified and directed. 34 S & F butt hinges, extruded aluminium alloy with brass wire pin, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996, hinge designation 125B21 as per IS 205: 1992 complete all as specified and as directed. 35 S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed. 36 S & F cast aluminium alloy handle, cast type, 125 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. 37 S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. 38 M& L for rendering/plastering 10mm thick in cement mortar 1:3 on faces of brick or concretesurfaces and finished the surface even and smooth without using extra with water proofing compound over chajja, coping etc complete in all respect as specifified and directed. (Water proofing compound shall be measured and paid under supply item only) 39 M& L for rendering/plastering 15 mm thick in cement mortar 1:4 on faces of brick or concretesurfaces and finished the surface even and smooth without using extra cement complete in all respect as specifified and directed. 40 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, complete in all respect as spefied and directed. 41 Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed. 42 S & F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed. 43 M&L for rendering/plastering 10mm thick in cement mortar 1:3 on faces of brick or concretesurfaces and finished the surface even and smooth without using extra with water proofing compound in sunken floor complete in all respect as specifified and directed. (Water proofing compound shall be measured and paid under supply item only) 44 M & L forAPP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm)laid on primed surface by torched applicationcomplete in all respect as specified and directed. 45 M&L for preparation of APP roof treatment surface of any description and apply two coats of aluminium paint over it complete in all respect as specified and directed. 46 Material and labour for brick work with sub-class B old size bricks of class designation 75, straight or curved on plan exceeding 6m mean radiusbuilt in cement mortar (1:6) including dismantling of existing brick work built in cement mortar complete in all respect as specified and directed. 47 M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed. 48 Supply and fix solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge. 49 Supplied and fixedFactory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete in all respect as specified and directed. 50 S & F mild steel door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed. 51 M & L for coloured non - skid ceramic (Premium quality ) tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour laid over and included 15 mm thick screed bed in cement mortar (CM) 1 :6, complete all as specified and as directed. 52 Providing and laying coloured ceramic(Premium quality ) tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over and including 10 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. 53 S&F in repair 20mm dia PVC coated over mild steel tube includingbracket, stops, rollers etc. complete all as specified and directed. 54 S&F in repair 15 mm bore GI tubesmedium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed. 55 S&F in repair 20 mm bore GI tubes medium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed. 56 Supplying and laying CPVC pipes for potable hot and cold water distribution, nominal size 16 mm, pressure class 1, SDR 11 including plain CPVC fittings of pressure class 1, SDR 11 in trenches complete all as specified and as directed. 57 Supplying and laying CPVC pipes for potable hot and cold water distribution, nominal size 20 mm, pressure class 1, SDR 11 including plain CPVC fittings of pressure class 1, SDR 11 in trenches complete all as specified and as directed. 58 S & F CPVC special transition fittings, elbow with brass threading, 16 mm nominal size complete all as specified and as directed. 59 S & F CPVC special transition fittings, elbow with brass threading, 20 mm nominal size complete all as specified and as directed. 60 S & F CPVC special transition fittings, elbow with brass threading, (2/4x 1/2) nominal size complete all as specified and as directed. 61 S & F CPVC special transition fittings, Tee with brass threading, 16 mm nominal size complete all as specified and as directed. 62 S & F CPVC special transition fittings, Tee with brass threading, 20 mm nominal size complete all as specified and as directed. 63 S & F CPVC special transition fittings, union with brass threading, 16 mm nominal size complete all as specified and as directed. 64 S & F CPVC special transition fittings, union with brass threading, 20 mm nominal size complete all as specified and as directed. 65 S&Fin repair 4 mm thick of size 600 mm x 450 mm bevelled edge mirror of selected quality decorative type mounted on 6 mm commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete in all respect as specified and directed. 66 Supply and fixed in position threelayered ISI marked rotational moulded polyethylene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) including cover, using new GI tank/PPR or other type of material tank nipples and unions for inlet and outlet pipe connection of same internal bore dia. and one for cleaning with dead plug , including dismantling and taking down of old unserviceable water storage tank complete in all respect as specified and directed. 67 S & F PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwedfor iron/CPVC pipe/fittings complete all as specified and directed. 68 S & F in repairs 15 mm nominal size, nonrising spindle type fancy concealed stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed 69 Taking down existing damaged EWC alongwith complete PCC and cement concrete from sunken floor and providing new EWC and seat cover and water proofing treatment to sunken floor as per following stages:-(a) 15 mm thick plastering in CM (1:3) with WPC at all around wall and base of sunken floor with proper slope.(b) Applying a coat of 85/25 gde hot bitumen @ 1.2Kg/ Sqm over a coat of bituminous primer @0.5Kg/Sqm and then pasteing of polythene film, 50 micron, natural colour with cold cut back adhessive. (c) Fixing of 25mm dia GI pipe (mediumgrade) spout of length 45 cm. (d) Supply & fixing of vitreous china wash down water closet pan (pedestal pattern), white, seat cover and P or S type bend etc complete includingproviding cement concrete and cement filling (1:5:10) and 25 mm thick PCC 1:2:4 at top surface.. 70 S & F in repairs 10 litres capacity, PVC low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed. 71 M & L for PVC connections 15 mm size with PTMT nuts of length 300/450 mm complete all as specified and as directed. 72 S & F in repairs 15 mm nominal size, nonrising spindle type fancy angle stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed. 73 S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed. 74 S &F Brass chromium plated shower rose 125mm size CP fix to iron pipe 15mm dia including fixing to steel pipe or union complete all as specified and directed. 75 S & F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed. 76 S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed. 77 S & F in repair Wash hand basins, vitreous China of size 550 x400mm(flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement,PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete all as specified and directed. 78 S & F in repairs health faucet with jet spray, 1.5 metre long, cast copper alloy, nickel chromium plated finish, 15 mm bore, 100 mm long with 1.5 metre long stainless steel shower hose and mounting device attached to wall complete all as specified and as directed by Engineer-in-Charge. 79 S & F PVC (SWR) nahani trap of 75mm outlet dia fixed with PVC 150X150mm size openable at center grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. 80 S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and as directed. 81 S & F PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 75 mm dia, fixed to walls complete all as specified and as directed. 82 S & F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed. 83 S & F UPVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, laid in trenches complete all as specified and directed. 84 S & FPVC (SWR) Tee(87.5°) single, 110 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge. 85 S & FPVC (SWR) Tee(87.5°) single, 75 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge. 86 S & F UPVC (SWR) bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 87 S & FUPVC (SWR) bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 88 S & FPVC (SWR) vent cowl, 110 mm dia conforming to IS 14735: 1999 complete all as specified and as directed. 89 S & FPVC (SWR) vent cowl, 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 90 Supply and fixed unplasticised PVC (SWR) Gully trap125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast. 91 M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed. 92 M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces of concrete complete all as specified and as directed. 93 M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed. 94 S & F sinks with drainage board made of stainless steel 1 mm thick sheet kitchen or laboratory with plugs, washers and 40 mm nominal size, copper alloy, nickel chromium plated finish waste fittings with including silicone sealant; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipes overall size 915 mm X 460 mm bowl size 410 mm X 330 mm X 160 mm complete all as specified and as directed. 95 S&F Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality A) including necessary welding complete complete allas specified and directed. 96 S & F expanded metal not exceeding 4 Kg per square metre, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and as directed. 97 M&L for preparation ofnew surface of plastered wall using wall care putty to fill the voids and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller overincluding one coat of alkali resistant priming paint over and including 3mm thick (in two layer), wall care putty complete all as specified and directed. 98 M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge. 99 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and as directed. 100 Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed. 101 M & L for cement concrete in foundation, filling and mass concrete in M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed. 102 M&L for PCC, 1:2:4 type B1,(using 20mm graded crushed stone aggregate) in copings, kneelers, apex stones, bed plates, kerbs, slightly rounded for chamfered angles and throating, complete all as specified and directed. 103 M & L for hardcore (broken stone or boulders) of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 104 Preparation of newly plastered surfaces on walls and applying three coats of white wash complete all as specified and as directed. 105 M & L for 40 mm thick damp proof course in cement concrete M15(Nominal mix) using 12.5 mm nominal size graded crushed stone aggregate mixed with integral water proofing compound to horizontal or vertical surfaces including necessary formworks complete all as specified and as directed. Note: - Water proofing compound shall be measured and paid for separately. 106 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed. 107 Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 108 Providing and laying for cement concrete in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabsusing type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form workcomplete in all respect as specifified and directed. 109 M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed. 110 S & F Joist, beams, channel, angle, hollow steel tubes or tee sections, fixed vertically independently connecting plates, etc. using Fe 410 -W (Gde- E- 250) quality- B complete in all respect as specified and directed. 111 S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. 112 M & L for mild steel iron frame for door , windowusing joist, channel, angle, tee, tubes, flat sections, fixed independently, without connecting plates, etc. conforming to Fe. 290., Gde-E-165complete in all respect as specifified and directed.(MS hinge shall be paid under supply only item) 113 S&f Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 114 Material and labour for plastering 10 mm thick on fair faces of brick work or concrete surfaces on ceilings in cement mortar 1:6 finished even and fair complete all as specified and as directed. 115 Supply only integral water proofing compound complete all as specified and as directed. 116 Preparation of newly plastered surfaces on ceilings and applying two coats of white wash complete all as specified and as directed. 117 S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 250 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. 118 S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed. 119 S & F aluminium alloy handle, cast type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.
