Tender For Special Repair For Bldg. No P 13/1, 13/2, 13/3 And 13/4 Ranjit Chowk Under Ge (East) Jrc; 1 Demolition of cement concrete floors and pavings n.exc 15cm thick (below or ground level) incl sunken floor etc and removing surplus spoil out of defence landwhere directed at a level not exc 1.5 m above the starting point all as specified and directed 2 M&L for 75mm PCC 1:3:6 type B1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth without using extra cement all as specified 3 M&L for forming construction joint 30mm deep x 10mm wide filled with sealing compound Gde A complete all as specified 4 M&L forcement concrete type E-2 1:5:10 (using 40mm graded stone agg ) as in sunken flooring 5 Material and labour for cleaning of cracks & filling of cracks with SIKA latex SBR 100 putty/ Dr fixit 302 SBR latex/ Perma latex SBR/ FORSROC Nitabond SBR latex/ Asian Paints latex as required.(a) Apply one coat of Acrylic modified cementitious coating of SIKA top Seal-107/Brush Bond FOSROC/ Dr Fixit/ STP/ CICO as per manufacturers instructions.(b) Apply glass fabric sheet of SIKA fab 1/ FOROC/ Dr Fixit/ STP while the first coat is wet. (c) Providing and applying a protection screed of 50mm thick in CM (1:4) mixed with Sika platocretere over the applied water proofing coating on horizontal surface and 50mm dia GI spout pipe 600mm(d) All the corners and joints should be pretreated with elastic waterproofing sealing tape with woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/ FOSROC/ Dr Fixit/ STP. Note : Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturers and approved by GE 6 M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded aggregate as in sub floor , sub base; concrete surface finished even &rough to receive topping floor/tiles finish/layer complete all as specified. 7 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified 8 M & L Vitrifiedceramic tiles light shad 10mm thick (Square/rectangular ) polished, area of each tilesexceeding 0.42sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade including 15mm thick screed bed or bedding layer in Cement Mortar (1:6) as in floor finished even and rough to receive the top layer all as specified and directed. 9 All as per item No 8 above buton vertical surfaces such asriser, skirting, dado,etc over and incl 10mm thick cement plaster in CM 1:4 rough finisher surface to receive tiles 10 M&L for non skidceramic colouredtiles of size exc 0.09 Sqm and not exc 0.11 Sqm, 6-7 mm thick in floor set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with & including screed bed or beading layer of morter 15mm thick in CM (1:6)for laying floor finishes , complete all as specified and directed. 11 M&L for non skid ceramic coloured tiles of size exc 0.11 Sqm and not exc 0.18 Sqm, 6-7 mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed. 12 All as peritem No 11 of above but in skirting and 10mm thick rendering as backing coat of CM 1:4 13 M& L for glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry andpointedin white or colour cement to match complete all as specified and rendering 10mm thickin CM 1:4 as in backing coat of wall tiles. 14 M&L for 20-25mm thick machine in cut kota stone slab in single piecesize in treadr & landings of stair cases including bull nose edge,over and incl 15mm thick bedding layer CM 1:6with pigments to match the shade of slab including cutting , rubbing and mirror finish polished complete all as specified and directed 15 Ditto all as per item No 14 above but 18-20mm thick on vertical surfaces such asriser, skirting, dudo,etc over and incl 10mm thick cement plaster in CM 1:4 rough finisher surface to receive tiles 16 Demolition of reinforced cement concrete of any description and in postiion not other wise specifically provided for. 17 M&L for MS TMT bars 10 mm dia and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for column hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia. 18 M&L for reinforcement cement concrete type B0 1:2:4 (12.5 mm graded aggregate) slabsupported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork complete all as specified 19 M&L for 18-20 mm thick machine cut granite (of any type ) tilesstone jointed with neat cement slurry mixed with pigment to match the colour of stone incl cutting and polishing and making hole in stone and RCC shelves suitable for gas pipe, with round edges where required and incl 15mm screed bed with CM1:6 all as specified and directed by Engr-in-Charge. 20 Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc and removing surplus spoil out of Defence Landwhere directed at a level not exc 1.5 m above the starting point all as specified 21 M&L 15 mm thick cement plaster in cement mortar 1:6 on internal surface of brick or concrete surface finished even and smooth withoutusing extra cementall as specified 22 M&L 15mm thick cement plaster in cement mortar 1:4 on external surface brick or concrete surface finished even and fairall as specified 23 M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement all as specified 24 S&F in repair squatting pan WC orissa pattern size 580 x 440 mm white with integral foot rest with P or S trap incl provn of cement concrete bedding incl breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor complete all as specifed. 25 S&F coloured vitreous china wash down one piece water closet withseat cover , hinges, Accessories set, size 625x350x730mmfitting with twin flush fitting with inlet ball valve float and handle,incl fixing bolt,with bottom and cover and mild steel chromimum plated hinging device withcomplete fixed in repairs all as specified and directed by Engr-in-Charge. 26 S&F Vitreous china wash hand basin , white/coloured, flat back 550x400mm ,withpedestal including one number stainles steel CP waste coupling ,32mm dia , Pvc waste pipe with connector , brackets 2 noscuttingfor and pinning in ends of bracketscomplete all as specified 27 S&F in repairPVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle, 10 ltr capacity including brakets complete all as specified and directed 28 S&F PVC connection , reinforced 45cm long 15mm in size with brass check nut and PVC washers at both ends complete all as specified 29 S&F 15mm Angle stop valves, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handlescrewed at two right angles endsfor both iron pipe or for unionsand fixed in repairs . Model No FON-40053 Make:- Jaquar and equivalent 30 S&F Bib tap cast copper alloy , chromium plated suitable for 15mm bore iron pipe with long body fancy type with wall flange complete fixed in repairs. Model No FLR-5047N Make:- Jaquar and equivalent 31 S&F in repair Wall Mixer 3-in-1 with provision for both Over Head Shower and Hand Shower complete with 115mm long bend Pipe, connecting legs & wall flange of suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed. Make Jaguar and equivalent 32 S&F in repair Hand Shower 105mm round shape multi flow with air effect(ABS body & face plate chrome plated) with rubit cleaning system as approved suitable for fixing to 15mm bore (dia)Pipe, complete as all specified and as directed. 33 S&Fstainless steel towel rack 600mm long with lower hanger with 3 hooks fixed in repair complete all as specified and directed 34 S&Fchromium plated towel ring15 cm dia complete fixed in repair complete all as specified Model No AQN-7721Make :- Jaquar and equivalent 35 S&F Chromium plated health faucetfor EWC with 1 m long CP tube with CP wall hook superior quality all as specified fixed in repair Make:- Jaquar and equivalent 36 S&F Toilet paper holder of Chromium platedfixed to walls with chromium plated (CP) brass screws,all as specified and directed fixed in repair Model NoAKP-35751P Make :- Jaquar and equivalent 37 S&F in repair Over Head Shower 140mm round shape/150mmx150mm Square, multi flow with air effect(ABS body & face plate chrome plated) with rubit cleaning system ofapproved MAKE suitable for fixing to 15mm bore (dia) Pipe, complete as all specified and as directed. 38 Supply and hanging bevelled edge mirror of any sizeof selectedquality glass 5.5 mm thick,fixed to wall withscrews and cup washers,hanging devices complete all as specified and directed 39 S&F Soap dish stainless steel chromium plated fixed in repair with brass screws andrawl plug complete all as specified Model No AKP-35731P.Make :- Jaquar and equivalent 40 S&F Corner Glass Shelf (with Bracket) complete all as specifed and directed Model No ACN-1173 Make :-Jaquar and equivalent 41 S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repair Model No ACN-1171N Make:- Jaquar and equivalent 42 M&Lfor PVC bath room cabinet of size 535 x 483 mm x 110 mm with mirrorfixed in repairs all as specified 43 S&F in repair, Stainless Steel Sink 1.0mm thick double Bowl size Overall size 932x442mm and Bowl size 428x392x225mm each for Kitchen or Laboratory with Plugs, Washers, Waste Fitting 32mm bore (dia) of Stainless steela Pair of Cast Iron Brackets duly Painted/ Erecting Stand including cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed. 44 S&Fin repairSink mixer swinging spout (Wall mounted) for Hot & cold water with connecting legs & wall flanges of approved MAKEsuitable for fixing to 15mm bore (dia)Pipe, complete as all specified and as directed. 45 S&F for S/S plate rack of superior quality size 2400mm X 3600 mm and not less than 8 kg all as specified and directed 46 S&Fin repair for stainlesssteel pipe 25 mm dia fancy typ curtain roadfixed in the bracketandfancy type finials/side brackets (both side), shade as approved by GE all as specified. 47 S & Fin repair 20mm diacurtain rails , mild steel , chromium plated fixing in cup board with brackets, stops, rollers etc, all as specified 48 Taking up or down 15 mm steel tubing and connections, including cleaning for re fixing or removal to store 49 Taking up or down 20mm steel tubing and connections, including cleaning for re fixing or removal to store 50 Supplying and laying of 16mmouter dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl all fittings socket, brass adapters etc complete all as specified and directed. 51 Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl all fittings socket adapters complete all as specified. 52 S&F CPVC Ball valve 20mm as in cpvc pipe complete all as specified. 53 S&F 1000 ltr rotational moulded polythylene water storage tank (Cylindrical vertical with closedtop) hosted and fixed in position incl dismantling of existing tank of any description complete all as specified.ISI marked. 54 S&F 500 ltr rotational moulded polythylene water storage tank (Cylindrical vertical with closedtop) hosted and fixed in position incl dismantling of existing tank of any description complete all as specified.ISI marked. 55 S&F 20mmdia Ball valves high pressure of PTMT with epoxy coated Aluminiumrod& highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight-210gms.) 56 S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement. 57 Demolition and braking up drain pipesAC/PVC pipe in event n.exc 150 mm dia including all fittings. 58 S&F for 110 mm PVC (SWR)Rain water pipessingle socketedin any length with rubber ring joints fixed towalls or Floor. 59 S&F for 75 mm PVC (SWR)Rain water pipessingle socketedin any length with rubber ring joints fixed towalls or Floor. 60 S&F PVC (SWR) bends 110 mm. 61 S&F PVC (SWR) bends 75 mm. 62 S&FPVC (SWR) junction single, (Single T) equal or unequal in radius 110 mm bore. 63 Taking down chowkats or frame not exc. 1.5 sq m each with shutters (without taking off shutters from the fames). 64 Taking down chowkats or frameexc. 1.5 sq m but n.exc 4 sq m each with shutters (without taking off shutters from the fames). 65 Taking down shutters exc. 2 sqm each. 66 S & F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet as reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed. 67 S & F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain mouldedPVC sheet polyurethane painted on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and as directed. 68 S&Ffactory made wire gauzed pvc Door 30mm thick (style) consisiting of frame made out ofM.S.Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour 10mm thick PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 10 mm thick PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame at the site as per specification & drawing. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly. 69 S & F 30mm thick factory madePVC Flush Cup board shutter consisting of panel of hollow section thickness . Consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm inserted inside the hollow section of stiles. top and bottom rails and two 19mm x 19mm MS tubes inserted horizontaly inside the hallow profile section at an equal distance from top and bottom of door and fixed with hallow profile section using 5mm thick PVC sheet using screws Hollow PVC profile shallbe lippedwith 10 mm ( 5mmx 2) thick x 20mm width on stiles and rails using solvent cement . The inner panel shall be laminated with 5mm thick thick termite proof . water proof and fire retardant Prelam PVC sheet using solvent cement on both the sides of the panel etc. Complete all as specified as per direction of Engineer-in -charge. 70 Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of H section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. U cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineerin-charge. 71 Supply and fixing Aluminium anodised powder coated Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed with 5mm thick tinted glass & one no. s/s wire mesh panels) upto 1.50m height made of (big series) frame 100 x 45 mm & sash 46 x 62 mm both having wall thickness of 1.5 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced galvanized mild steel section made from roll forming process of required length (shape & size according to aluminium section), appropriate dimension of extruded glazing beads andextruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. 72 Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm(± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge. 73 S&F 2nd class hard wood35mm thickness of factory made plain framed, panelled shutter with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated. 74 S & Ffactory made IInd Class hardwood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkats, complete all as specified and directed. 75 M&L for pressed steel frame of size 125x60mm for doors with one or more rebates including necessary fixinglugs, hinges,lock strike plate etc complete all as specified and directed. 76 M&L for pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixinglugs, hinges,lock strike plate etc complete all as specified and directed. 77 M&L Aluminium anodised frame for doors ,windows ventilators with one or more rebates incl joining cleat for fixing etc all as specified. 78 M&L Aluminium anodised window and ventilator side hung type w/o sash bars shutter aluminium section weighing .55 kg/m including necessary cleats glazing clips, rubber neoprene packing,hinges, anodised aluminiun snap beading screws anodised alumininum fittings such as peg stays 150mm long 1 no hinges type B-21 100mm long 2 nossuitable handle 1 no etc all as specified. 79 M & L coloured sheet glass selected quality plain 5.5mm thickness fixed in door shutter/window shutter cut to required size with PVC / Neopane gasket and Aluminium snap beadingComplete all as specified and directed. 80 Supplying and fixing steel windows 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises of glazedsutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf conisting two Nos sash bar of T section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWR bot T section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1, four Nosfor each window including following fittings welded to failed shutter:-(a) Holdfasts 150 mm long 12mm x 3 mm made to shape- 4 Nos per window(b) Handle of Z sec 20 mm x 25 mm, 100 mm long - 1 nos per leaf.(c) MS tower bolt 150 mm long -2Nos per leaf.(d) Z sec 20 mm x 25 mm , 100 long stopper-01 Nos per leaf,(e) Cleat 55mm long of hollow square 15 mm x 20 mm x 63 mm welded to hinges - 1 Nos per leaf(f) MS pintal hinges of size 75 mm x 12 mm - 2Nos per leaf.(g) fabriction and fixing arrangement complete.Note:- Grill / guard war , glass paneshall be measured and Paid saperately. 81 All as per description of serial item No. 80above but in gauged shutters without sash bars all as specified and directed. 82 S&F 18 to 20mm thick granite(of any type) tilesmachine cut , in skirting/dado/window cill/jamb laid over rendering10mm thick in CM 1:4 and jointedwith grey cement slurry and pointedwith white cementwith admixture of pigmentto matchthe shade of granite stone includinggrinding and polishing complete. 83 S&F in repairfactory made 18mm thick 100% solid WPC (wood polymer Composite) pain board of required size kitchen cabinate as in partition, shelves, wall,drawer ,shutter, etc of required colourcomprising of virgin PVC resign ofvalue 57-60 (suspension Grade), Calcium Carbonate and naturalFibres (Wood Powders/rice husk/wheat husk) and Non toxic additives, made from extrusion process WPC foam sheet single extruded (inner) with density not less than 650kg/cum manufactured by certified company having good screw holding capacity(Screw withdraw stregnth of 2000N (face) & 1100N (edge) Minimum compressive strength of 50N/mm2, modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with property of being Termit/Borer free, water/Moisture proof, Fire Retardantand fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, All as per direction of Engr in Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company Make Rajshri or equivalent. 84 All as per item No 83 but solid WPC (wood polymer Composite)boarddecorative one side complete all as specified and directed. 85 S&F stainless steel self closing hinge of 75 mm size for PVC door shutter / kitchen cabinet complete as specified and directed. 86 S&F 50 X 15 mm size magnet door catcher for closing for PVC shutter complete as specified and directed. 87 S&F 100 mm size MS mat / glossy finish handle complete as specified and dirceted. 88 S&F mild steel drawer cabinet channel for moving the drawer etc complete as specified and directed. 89 Supply & fix modular type stainless steel plain basket of size 15”x18”x4” (dia of wire not less than 3.0mm) of any shape with side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arranement (Make: Everlite/ Slimline/Peacock/Fabshine) complete all as specified & directed. 90 All as per item no 89 as above butstainless steel plain basket of size 15”x18”x6”complete all as specified & directed. 91 All as per item no 89 as above butstainless steel plain basket of size 15”x18”x8” complete all as specified & directed. 92 All as per item no 89 as above butstainless steel partition of size 17”x20”x6”all as specified & directed. 93 All as per item no 89 as above but stainless steel cutlery of size 17”x20”x6”complete all as specified and directed. 94 All as per item no 89 as above butstainless steel grain trolly with stand of size 21”x17”x10” complete all as specified and directed. 95 All as per item no 89 as above butstainless steel cup & soucer, trolly of size 15”x18”x4”complete all as specified and directed. 96 All as per item no 89 as above butstainless steel Plate basket of size 24x30complete all as specified and directed. 97 Supply, Fixing and installation of wall mounted Electric Kitchen Chimney of size 75 cm, compact design suction 1400m3/hr Auto clean type touch control with wave sensor duct dia 150mm including free Kit for installation with duct cover of adequate size make as approved by GE. 98 S&F magic eye brass best quality fixed inmain door shutter approved by Engineer in charge complete all as specified and directed. 99 S&F peg set of six made of stainless steel all as direcred and specified. 100 S&F butt hinges medium weight,Stainless steel , bright polished 75 mm size for fixing PVC cup boardShutter. 101 S&F butt hinges medium weight,Stainless steel , bright polished 100 mm size for fixing PVC Door Shutter. 102 S&F brasshandles125 mm size fixed with screws all as specified. 103 S&F brass tower bolts, 150mm long fixed withscrew all as specified and directed. 104 S&F150 mmaluminium anodised barel tower bolt, of extruded section and fixed complete all as specified. 105 S&F100 mmaluminium alloy handles, cast type, anodisedcomplete all as specified. 106 S & F Hasp & Staple aluminium 100 mm , including bolt to hinge plate and fixed with screws with Cup Board shutter, all as Specified. 107 S & F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars barallel iron doors and similar work conforming to Fe.290.Gde-E-165. 108 S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks. 109 M&L for 3.00 mm thick glass sheet, ordinary quality and glazing with oil putty in square n. exc 0.5 sq. m in each pane. 110 M&L for 3.00 mm thick plain figured glass, pin headed type andglazing with in oil putty in sqaure n exc .5 sqm in each pane. 111 S&Fbrass floor door stopper 63 mm with two rubber legged all as specified and directed. 112 S&F 300 mm long brass sliding door bolts with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolt and fixedcomplete all as specified. 113 S&F for 300mm brass ordinary rat tail pattern springs incl roller plate complete as specified. 114 Dismantling of plain or corrugated steel sheeting any gauge thickness including nainital or similar pattern in roof covering complete all as specified and directed. 115 S&F0.50mm thick (including coated thickness) pre-colour, pre-profiled (Galvalume/Zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof, wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer/profile maker instruction complete all as specified and directed. 116 M&L for steel work in tubular/angle trusses, purlins, rafter,tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 gradeSt.-240 complete all as specified and directed. 117 Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth. 118 S&F in repair wash basin mixer tap fancy type chromium plated, screwed down high pressure with or without lettered Hot or cold with long screwed for 15mm bore iron pipe and fixed complete all as specified & directed make Jaguar or equivalent. 119 S&F structural steel framed work as in doors frame or gates of angleor other section with gusset plates, rails, braces etc. Cutting, drilling and welding complete, drilled for fixing of steel sheeting or other covering.Doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed. 120 Dismantlingof brick tiles single layer as in roofcovering complete all as specified. 121 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof) removing surplus spoil out of Defence Landwhere directed at a level not exc 1.5 m above the starting point all as specified. 122 M&L Cutting out cracks to V-section in existing RCC roof slabs or terracing , cleaning out & filling solidly with a hot mixture of bitumen and clean dry sand 1:1 ( by weight) all as specified. 123 M&L for PCC (1:2:4) typeB-0 (using 12.5 mm graded stone aggregate) as in benching, roof padding,roof kerbs or mud stops, coping etc rounded or chamfered on edges. 124 M&L 10mm thick cement plaster in cement mortar (1:3) on concrete roof surfaces finished even and fair, including cleaning theroof top by water etc all as specifiedand directed by Engr in charge with WPC. 125 Cleaning the surface and made free of dirt, foreign particle, laitance followed by grinding all all protrusion to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expiation contraction. Cutting the grooves with suitable cutter machine in V groove filled with repairs mortar/ microconcrate / general purpose grout as recommended proportionally as per recommendation of manufacture. Making of Gollas at all the corners with polymer modified mortar (1:4) cement sand with 3.5% acylic of cement weight. 126 Supply and applying high build elastomeric waterproofing coating based on pure hydrophobic polyurethane cold appliId of spray/brush applied, membrane with an elongation of 280% and tensile strength of 2.7N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88% solid content. The system includes final base preparation, epoxy primer 1:1 (Resin; harder) application with 100% water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 kg per Sqm. Application should be done with Graco sprayer by a companies authorised applicator ”. 127 Demolitionof brick workor stone/boulders masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars etc. and rubbish materials remove from site all as specified and directed. 128 Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6. 129 M&Lfor repairing of RCC projections, chajjas , roofs, facia etc. by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced withwelded mesh of weightexc 2kg per sqmtrbut n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor. 130 M&L forpreparing new plastered or unplastered wall surfaces and appliedtwo coat of Anti fungal weather coat aacrylic emulsion paint over a coat of primer (X2) complete all as specified and directed by Engr-in-charge. 131 M&L for preparing new surfaces plastered or unplastered surfaces of walls byapply a uniform layer of wall care putty as approved after that let the surface dry then apply two coats of oil bound distemper white or tinted over a coat ofprimer complete all as specified. 132 M&L for three coats of white wash on newly plastered surfaces ofceiling includingpreparation of ceilingsurfaces complete all as specified and directed by Engr-in-charge. 133 Material and labour for complete removal of old decorated plastered surfaces of wall,pillasters, cornices etc by brooming down or steel wire brushing scrapping down and washing with water after completion of precoat treatment apply two coats of Anti fungal weather coat aacrylic emulsion paint over a coat of primer (X2) complete all as specified and directed Make of Arcylic emulsion weather coat paint :- Asian (Apex Ultima), Berger (Super coat) or ICI Dulux (weather shield) Make of primer :- Asian (X2) or Equivalent Note :-(a) Each stage i.e preparation of surfaces,application of primer,application of first coat.application of second coat will be got passed from Engr-in-Charge (b) Written Warranty for four years or as per manufacturers instructions, whichever is more is required to be furnished by contractor for this item. 134 M&L complete removal of the existing tratement on walls for Preparation of wall surfaces by scrapping (any No of layers), rubbing down,washing, etc as directed and apply a uniform layer of wall care putty as approved after that let the surface dry then apply two coats of oil bound distemper white or tintedall as directed and specified. 135 M&L for prepration of old surfaces of walls including scraping down smoke soots, moulds, moss and trading oil and greasy spots etc including cornices, pilasters etc( Plastered or un plastered surfaces) and applying two coat of white (lime) wash on ceiling complete all as specified and directed by Engr-in-charge. 136 M&L for preparation of new steel surfaces of any description, not otherwise described over 10cm width or girth and applied two coat of synthetic enamel paint over one coat of red oxidezinc chrome primer complete all as specified and directed by Engr-in-charge. 137 M&L complete removal of the existing tratement on walls for Preparation of wall surfaces by scrapping (any No of layers), rubbing down,washing, etc as directed and applytwo coats of cement base paintall as directed and specified. 138 M&L complete removal of the existing tratement on walls for Preparation of wall surfaces by scrapping (any No of layers), rubbing down,washing, etc as directed and applytwo coats of white wash on wallall as directed and specified. 139 M&L for 75mm thick cement concrete type D-2, 1:4:8( 40 mm grade agg) as in sub base of floor complete all as specified and directed. 140 M&L for durastone vitrified tile 400x400x10 to 12mm thick infloors etc. set and jointed in neat cement slurry and pointed in white orcoloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified and directed. 141 S&F 60 mm thick precast cement concrete M-35 machine pressed inter locking tiles with grey cement and pigments all as specified. 142 M&L for sand cusioning with layer of fine sand 25mm thick over PCC for laying of interlocking paver block complete all as specified and directed. 143 M&L for providing 25mm thick (measured solid) precast cement concrete loures and jallies in PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) including all moulding but excluding frame set in cement mortar (1:4) and incl taking down old jallies complete all as specified and directed. 144 M&L for repair to rolling shutter including ball bearing, greasing and make functional complete all as specified and directed. 145 M&L for preparation of old stone surface of any description over 10 cm girth or width not other described and applying one coat of synthetic enamel paintcomplete all as specified and directed. 146 Dismantling of fencing post/struts of any description (wooden /steel or RCC)incl taking out embeded portion in concrete and making good to disturbed surface complete all as specified and directed. 147 Dismantling chain Link fencing with mesh any type. 148 Excavation in post holes(or similar holes) each in not exc. 0.50 cum getting out returning,filling in an ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm watering and removing surplus soil to a distance not exc. 50 Mtr and making good surface all as specified & directed. 149 PCC(1:3:6) type C2 (40mm graded stone aggregate) filling in post holes, foundation,and other similar work complete all as specified. 150 M&L for Mild steel angle iron fencing posts and struts in fencing including necessary cutting , drilling , welding etc and bending to swan neck shape as required and drilling holes notching for wire etc conforming to Fe-410-0 or 310-0 complete all as specified and directed by Engr-in-Charge. 151 S&F MS chain link fencing10 guage thickgalvanised steel wire and 50mm x 50mm size mesh fixed tosteel fencing post by nut & bolts etc including provision of binding wire complete all as specified and directed by Engineer-in-Charge . 152 Dismantling of structural steel wors as in grill ,door gatetc complet all as specified and directed. 153 S&F structural steel framed work as in doors frame or gates including hold fast of angle or other section with gusset plates, rails, braces etc. Cutting, drilling and welding complete, drilled for fixing of steel sheeting or other covering.Doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed. 154 Mild Steel work in flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engrneer-in-charge. 155 S&F mild steel bolt purpose made with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut approved by Engineer in charge complete all as specified. 156 Prepration of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. 157 S&F 18 to 20mm thick granite(of any type) tilesmachine cut , in skirting/dado/window cill/jamb laid over cementscreed 10mm thick in CM 1:4 and jointedwith grey cement slurry and pointedwith white cementwith admixture of pigmentto matchthe shade of granite stone includinggrinding and polishing complete. 158 Taking down carefully existing point wiring of any type/ any size (ie on wooden/ batten, surface conduit, casing capping or concealed conduit) complete for light, fan, socket or power point etc includingremoving switches, sockets, holders, ceiling rose, pendants, regulators, light fittings, switch board outlets with sheets and other materials from site for refixing of serviceable light, accessories for taking credit of unserviceable light and accessories as per Sch of creditand making good disturbed surface of walls,roof, floors etc. with any type of civil wk involved complete all as specified and directed. 159 M&L for point wiring for light/fan point with 1.5 Sqmm (nominal area) FRLS PVCinsulated unsheathedmulti stranded copper conductor of size 1.5 Sqmm cabledrawn in and including concealed rigid PVC conduit medium grade not less than 20mm dia with accessories including cutting chases for laying of conduit /fixing of boxes in walls/floor etc including making good to disturbed surfaces as per adjoining specification and terminated in and incl sunken pressed steel boxes duly painted with anti corrosive paint over a coat of red oxide primer with plastic laminated bakelite sheet top cover 3mm thick make hylum or equivalent fixed with nickel polished screws with cupwashers etc including FRLS PVC insulated unsheathed multi stranded copper conductor 1.5 Sqmm single core as earth continuity conductor (green colour) connected with earth dolly with thimble complete all as specified and as directed by Engr-in-Charge. 160 All as per srl item No.159 here in before but for one socket outlet 5 Amps on independent board complete all as specified. 161 All as per srl item No. 159 here in before but for one socket outlet 5 Amps on the sameboard controlled complete all as specified. 162 All as per srl item No. 159 here in before but for one bell point controlled by one bell push complete all as specified. 163 All as per srl item No. 159 here in before but for one light point controlled by two way switches complete all as specified. 164 All as per srl item No. 159 here in before but with 2.5 Sqmm(nominal area) FRLS PVC insulated unsheathed multistranded copper conductor cable for one 3 Pin 15 Amp socket on independent board including one 2.5 Sqmm copper conductor multi stranded green colour PVC insulated unsheathedFRLS cable 1100 volts grade as earth wire connected to common earth and earth dolly with all accessories complete all as specified and directed by Engineer-in-Charge. 165 S&F in replacement switch piano flush type, 5 Amps, single pole, two way complete all as specified. 166 S&F switch piano flush type, 6 Amps single pole, one way complete all as specified. 167 S&F switch piano flush type 16 Amps single pole, one way complete all as specified. 168 S&F socket out let 6 Amp, 6 pin, 2-in-1 flush type complete all as specified. 169 S&F Socket outlet multi purpose 2 in 1, 5/6 pin, 6 & 16 Amps, flush type complete all as specified. 170 S&F in replacement bell push switch flush type 6 Amps, single pole complete all as specified and directed. 171 S&Fin repairDecorative wall mounting light fitting suitable for 09 watt LED lampcomplete with glass shade/ polycarbonate cover including 1 x 09watt LED lamp complete all as specified and directed by Engr-in-Charge. 172 S&F ceiling rose surface type PVC/ polycarbonate 65mm x 50mm three terminal complete all as specified. 173 M&L in replacement call bell electric AC (Ding Dong) 240 volt SP complete all as specified. 174 M&L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittingsall as specified and directed. 175 S&Ffive step fan regulator, electronic type, single phase,including connection complete all as specified. 176 M&L forsub main wiring with two run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of4 Sqmm drawn through in and includingnew PVC rigid non metallic concealed conduit(medium grade) with all fittings including earth continuitysingle wire FRLS PVC insulated unsheathed multistranded copper conductor cable 4.0 Sqmm ( green insulation) with any type of civil work including making good to disturbed surfaces to match existing surface complete all as specified.NOTE: Two run of 4 sqmm wire and one run of 4 sqmm wireas earth wire includingPVC conduit shall be measured as one unit. 177 M&L for replacement of sub main wiring with Four run of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of 6 Sqmm drawn through in and including PVC rigid non metallic concealed conduit(medium grade ISI marked) with all fittings including two run of earth continuity FRLS PVC insulated unsheathed multistranded copper conductor cable 6.0 Sqmm PVC insulated with green insulation with any type of civil wk involved complete all as specified. NOTE: Four run of 6 sqmm wire and two run of 6 sqmm wireas earth wire includingPVC conduit shall be measured as one unit. 178 M&L in replacement for sheet metal DB for MCBs, SPN, 4 ways, double door,single phase, with bus bar, neutral bar/ connectors suitable copper thimbles, lugs etc complete all as specified.Make: EKINOX3 series of Legrend/Acti 9 metalic series of Schneider/Optipro of Indoasian/Osafe of HPL/Metallica of Havells. 179 Supply & FixMCB SPN 32 Amps 240 V, 10 KA, B curve as per Osafe series of HPL/ Acti 9 series of Schneider/ Optipro of Indoasian or equivalent in Havells/ Legrend/ ABB/ Siemens/ Hager. complete all as specified and directed by Engr-in-charge. 180 M&L in replacement for sheet metal enclosurewithconnectors double door epoxy/ powder coated paint inside and out side TPN 6 ways complete all as specified. 181 Supply & FixMCB SP 6 to 32 Amps 240 V, 10 KA, B curve as per Osafe series of HPL/ Acti 9 series of Schneider/ Optipro of Indoasian or equivalent in Havells/ Legrend/ ABB/ Siemens/ Hager. complete all as specified and directed by Engr-in-charge. 182 Supply and fixing 415V 10KA B curve miniature circuit breaker TPNMCBof40 Amps complete with connection testing and commissioning complete all as specified and directed by Engr-in-charge. 183 Supply and fixing LED lights fitting 1x 20 Watt, 220V AC decorative box type frame with holder including LED tube rod 20 watt connecting up single/ double connections with three core flexible copper conductor cable of suitable size from ceiling rose complete. 184 Supply and fixing LED light fitting mirror type with high out put diffuser 9/10 watt 220 V AC decorative type including connecting up with three core flexible copper conductor cable of suitable size complete. 185 S & F energy saving & environmental friendly long life versatile pressure die-cast aluminium housing luminaire with heat resistant glass and suitable optics for uniform distribution of light 35 watt LED bldg security lights with high efficiency electronic driver BIS approved, having IP-66 protection,surge protection operative on AC supply 140 volts to 270 volts pre-wired complete with GI pipe of 25mm bore of suitable length and MS clamp duly painted with two coat Aloxide paint all as specified and directed. 186 S & F LED light fitting 1 x 9/10 W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 187 Supply and fix Single pole and neutral sheet metal encloser with a two pin and earth plug and socket complete with one SP MCB 20 Amps including Top Plug complete all as specified & directed by Engineer-in- charge . 188 Taking down carefully Exhaust Fan of any sweep or make, painting of fans complete (as per previous colour) with synthetic enamel paint by spraying, cleaning all dust etc including replacement of flexible wire,bolts all as specified and directed. 189 Re-fixing of Exhaust Fan of any sweep duly greasing and minor repair work complete all as specified and directed. 190 Supply and fix exhaust fan, Metal body AC single Phase. 230V of size 225/230 mm sweep with blades, frame and louvers completeincluding making/ cutting of hole in wall of any thickness and making good to disturbed surface complete incl plastering all as specified and directed. 191 Supply and fixing in replacement FRLS PVCinsulated unsheathedmulti stranded copper conductor of size 1.5 Sqmm single core in existing pipe complete all as specified and directed. 192 Fixing only serviceable tube light fittings any type and any description retrieved under item Srl No. 01, including necessary electric connection with round flexible wire with multi stranded copper conductor of size 0.50 sqmm, 3 core, 1100 volts grade completeall as directed. 193 M & L Service connectionof4 Sq mm twin core Weather proof aluminium conductor cable suspended with No 8 SWG GI wire from Pole to service bracket & then to meter/DB complete with provn of porcelain insulators complete. 194 Hanging of ceiling fan of any sweep duly minor repair work such as replacement of capacitor, flexible wire and rubber reel etc complete all as specified and directed. 195 Taking down Geyser of any capacity or model after disconnecting all water supply and electric connections complete all as specified and directed. 196 Painting of geyser ( as per existing colour) by spraying with two coat of synthetic enamelled paint after cleaning all dust etc, after preparation of surface cleaning of inner tank and minor repair work and re-fixing with new fastner including water and eletrical connection complete all as specified and directed. 197 M&Lfor PVC connections for water heaters with pvc flexible pipe 15mm dia 450 mm long, suitable for hot water size with 02 Nos connectors and washers complete. 198 M& L for XLPE insulated, PVC sheathed galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with strandedaluminium conductor of size 25 sqmm 4 core complete laid in trenches passing through pipes/culverts/ under roades/ alon wallall as specified and directed by Engineer-in-charge. 199 Excavation in trenches in soft/Loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and getting out complete all as specified and directed by Engineer-in -Charge. 200 Returning and filling in, including spreading and levelling, water and well remming in layers not exc. 25cm all as specified and directed. 201 Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed. 202 Supply and laying old size sub class B bricks laid flat in trenchs over the cable with the length of brick perpendicular to the direction of cable length, compressive strength of brick shall not be less than 160 kg/cm² adjacent/abutting each other complete all as specified and directed by Engineer-in-Charge. 203 Material and labour Sand cushioning with 8cm thick layer of sand before laying of cable and 15cm thick after laying of cable in trenches complete all as specified and as directed. 204 M&L for GI tube light grade 50mm bore laid in trenches or fixed on wall/floor for protection of UG cable complete all as specified and directed.
