Construction Of Phase-B Works At Jawahar Navodaya Vidyalaya At Ramgarh ( Jharkhand ), ramgarh-Jharkhand

Construction Of Phase-B Works At Jawahar Navodaya Vidyalaya At Ramgarh ( Jharkhand ) - 1 0.375 BOYS DORMITORY WITH 2 NOS. WARDEN RESIDENCE(G+1) 2 CIVIL WORK 3 Earth Work 4 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil 5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 6 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.All kinds of soil 7 Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. 8 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 9 Concrete Work 10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stoneaggregate 40 mm nominal size derived from natural sources) 11 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 12 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 13 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stoneaggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 14 Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 15 Reinforced Cement Concrete 16 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 17 Foundations, footings, bases of columns, etc. for mass concrete. 18 Suspended floors, roofs, landings, balconies and access platform. 19 Lintels, beams, plinth beams, girders, bressumers 20 Columns,Pillars, Piers, Abutments, Posts and Struts. 21 Edges of slabs and breaks in floors and walls Under 20 cm wide. 22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 23 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 24 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 25 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement contentin design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 26 All works upto plinth level 27 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 28 (i) R.C.C. work in Footing 29 (ii) R.C.C. work in Beam 30 (iii) R.C.C. work in Columns 31 All works above plinth level upto floor V level 32 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 33 (i) R.C.C. work in Lintel 34 (ii) R.C.C. work in Beam 35 (iii) R.C.C. work in Columns 36 (iv) R.C.C. work in Slab 37 Expansion Joint Treatment 38 Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that commodates multi directional seismic movement without stress to its components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). 39 Floor Joint of 100 mm gap 40 Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints Systemsuitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). 41 Wall Joint of 100 mm gap 42 Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed toaccommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement.(Material shall confirm to ASTM 6063.) 43 Roof Joint of 100 mm gap 44 Masonry Work 45 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) 46 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 47 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in superstructure above plinth level up to floor V levelin : Cement mortar 1:6 (1 cement : 6 coarse sand) 48 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 49 Cladding Work 50 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 51 Granite stone slab colour black, Cherry/Ruby red 52 Area of slab upto 0.50 sqm 53 Area of slab over 0.50 sqm 54 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 55 Granite work 56 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 57 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 58 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 59 Wood and PVC Work 60 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 61 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 62 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 63 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 64 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 65 300 mm weighing not less than 200 gms 66 250 mm weighing not less than 150 gms 67 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 68 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in-charge. 69 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick 70 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size Kiln seasoned and chemically treated hollock wood 71 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 72 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 73 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete.(a) 250mm x 16mm . 74 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 75 200 x 10mm 76 150 x 10mm 77 Steel Work 78 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 79 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 80 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 81 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. 82 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 83 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 84 Flooring 85 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement 86 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 87 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 88 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm 89 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm 90 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 91 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 92 P & laying cement concrete 93 Finishing 94 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 95 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 96 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 97 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 98 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 99 Steel Painting:Applying priming coat: 100 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 101 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 102 Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : 103 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 104 Water Proofing 105 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 106 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 107 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 108 Providing and filling of AAC Lightweight Broken Blocks sunken portions. 109 2.1 Mt high Boundary wall 110 PLUMBING INTERNAL ESTIMATE( 0.375 Unit Boys Dormitory with 2 Nos Warden Residence ) 111 Sub Head– I Sanitary Installation 112 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 113 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 114 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 115 W.C. pan with ISI marked white solid plastic seat and lid 116 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 117 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 118 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 119 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 120 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 121 Providing and fixing toilet paper holder : 122 C.P. brass 123 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 124 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 125 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 126 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 127 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 128 Kitchen sink with drain board 129 510x1040 mm bowl depth 250mm 130 Kitchen sink without drain board 131 610x460 mm bowl depth 200 mm 132 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 133 Size 450x300x150 mm 134 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 135 Flexible pipe 136 40 mm dia 137 Providing and fixing soil, waste and vent pipes : 138 100 mm dia 139 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 140 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 141 100 mm 142 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 143 Providing and fixing plain bend of required degree. 144 100 mm 145 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 146 Providing and fixing heel rest sanitary bend 147 100 mm dia 148 Sand cast iron S&S as per IS - 3989 149 Providing and fixing double equal plain junction of required degree 150 100x100x100x100 mm 151 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 152 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 153 100x100x100 mm 154 sand cast Iron S&S as per IS: 3989 155 Providing and fixing single equal plain junction of required degree 156 100x100x100 mm 157 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 158 Providing and fixing terminal guard: 159 100 mm 160 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 161 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 162 100 mm 163 S S 304 grade coupling with EPDM rubber gasket 164 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 165 100 mm 166 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 167 100 mm diameter pipe 168 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 169 100 mm diameter pipe 170 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 171 32 mm dia. nominal bore 172 40 mm dia. nominal bore 173 50 mm dia. nominal bore 174 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 175 100 mm inlet and 100 mm outlet 176 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 177 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 178 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 179 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 180 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 181 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 182 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 183 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 184 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 185 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 186 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 187 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 188 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 189 Coupler 190 110 mm 191 Single tee with door 192 110x110x110 mm 193 Bend 87.5° 194 110 mm 195 Shoe (Plain) 196 110 mm Shoe 197 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 198 110 mm 199 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 200 110 mm outer dia 201 50 mm outer dia 202 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 203 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 204 Sub Head– II Water Supply 205 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 206 Internal work – Exposed on wall. 207 20 mm nominal outer dia Pipes 208 25 mm nominal outer dia Pipes 209 32 mm nominal outer dia Pipes 210 40 mm nominal outer dia Pipes 211 50 mm nominal outer dia Pipes 212 65 mm nominal outer dia Pipes 213 80 mm nominal outer dia Pipes 214 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 215 Concealed including cutting chases and making good the wall etc. 216 15 mm nominal outer dia Pipes 217 20 mm nominal outer dia Pipes 218 25 mm nominal outer dia Pipes 219 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 220 20 mm dia. nominal bore 221 25 mm dia. nominal bore 222 32 mm dia. nominal bore 223 40 mm dia. nominal bore 224 50 mm dia. nominal bore 225 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 226 25 mm nominal bore 227 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 228 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 229 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 230 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 231 15 mm nominal bore 232 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 233 15 mm nominal bore 234 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 235 15mm nominal bore 236 Providing and fixing uplasticised PVC connection pipe with brass unions : 237 45 cm length 238 15 mm nominal bore 239 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 240 150 mm diameter 241 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 242 (a) 15 mm nominal dia 243 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 244 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 245 upto 50 mm dia. nominal bore 246 SUBHEAD– III Drainage 247 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 248 150 mm diameter 249 200 mm diameter 250 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 251 180x150 mm size P type 252 With fly ash bricks (non modular) bricks of class designation 7.5 253 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 254 150 mm dia. R.C.C. pipe 255 250 mm dia. R.C.C. pipe 256 300 mm dia. R.C.C. pipe 257 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 258 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 259 with common brunt clay FPS ( non modular )bricks of class designation 7.5 260 Extra depth formanhole 90x80 cm 261 With FPSbricks class designation 7.5 262 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 263 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 264 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 265 ELECTRICAL Works 0.375 BOYS DORMITORY WITH 2 NOS. WARDEN RESIDENCE 266 SUB HEAD - I: CIRCUIT CUM POINT WIRING 267 SWITCH CONTROL LIGHT POINTS 268 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 269 Group C 270 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 271 Group C 272 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 273 Group C 274 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 275 Group C 276 MCB CONTROL LIGHT POINTS 277 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 278 Primary point controlled by one MCB. 279 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 280 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 281 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 282 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 283 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 284 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 285 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 286 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 287 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 288 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 289 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 290 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 291 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 292 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 293 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 294 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 295 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 296 Telephone socket outlet 297 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 298 1 or 2 Module (75mmX75mm) 299 6 module (78mm X 205 mm X 50 mm) 300 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 301 3 pin , 5/6 amps socket outlet 302 5/6 amps switch 303 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 304 25 mm 305 32 mm 306 SUBHEAD -II - FITTINGS & FIXTURES 307 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 308 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 309 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 310 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 311 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 312 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 313 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 314 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 315 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 316 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 317 SUBHEAD - III - DISTRIBUTION BOARDS 318 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 319 6 way, Double door 320 8 way, Double door 321 12 way, Double door 322 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 323 4 way (4 + 12), Double door 324 6 way (4 + 18), Double door 325 8 way (4 + 24), Double door 326 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 327 12 way (4 + 36), Double door 328 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 329 Single Pole 330 Single Pole Neutral 331 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 332 40 A 333 63 A 334 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 335 25 A 336 40 A 337 63 A 338 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 339 25 A 340 40 A 341 63 A 342 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 343 SUB HEAD-IV , LIGHTNING CONDUCTOR 344 LIGHTNING CONDUCTOR 345 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 346 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 347 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 348 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 349 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 350 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 351 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 352 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 353 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 354 0.375 GIRLS DORMITORY WITH 3 NOS. WARDEN RESIDENCE(G+2) 355 CIVIL WORK 356 Earth Work 357 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil 358 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 359 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.All kinds of soil 360 Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. 361 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 362 Concrete Work 363 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 364 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 365 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 366 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stoneaggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 367 Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 368 Reinforced Cement Concrete 369 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 370 Foundations, footings, bases of columns, etc. for mass concrete. 371 Suspended floors, roofs, landings, balconies and access platform. 372 Lintels, beams, plinth beams, girders, bressumers 373 Columns,Pillars, Piers, Abutments, Posts and Struts. 374 Edges of slabs and breaks in floors and walls Under 20 cm wide. 375 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 376 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 377 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 378 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 379 All works upto plinth level 380 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 381 (i) R.C.C. work in Footing 382 (ii) R.C.C. work in Beam 383 (iii) R.C.C. work in Columns 384 All works above plinth level upto floor V level 385 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 386 (i) R.C.C. work in Lintel 387 (ii) R.C.C. work in Beam 388 (iii) R.C.C. work in Columns 389 (iv) R.C.C. work in Slab 390 Expansion Joint Treatment 391 Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that commodates multi directional seismic movement without stress to its components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). 392 Floor Joint of 100 mm gap 393 Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints Systemsuitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). 394 Wall Joint of 100 mm gap 395 Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to 396 accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement.(Material shall confirm to ASTM 6063.) 397 Roof Joint of 100 mm gap 398 Masonry Work 399 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) 400 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 401 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in superstructure above plinth level up to floor V levelin : Cement mortar 1:6 (1 cement : 6 coarse sand) 402 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in foundation and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand) 403 Cladding Work 404 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 405 Granite stone slab colour black, Cherry/Ruby red 406 Area of slab upto 0.50 sqm 407 Area of slab over 0.50 sqm 408 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 409 Granite work 410 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 411 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 412 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 413 Wood and PVC Work 414 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 415 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 416 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 417 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 418 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 419 300 mm weighing not less than 200 gms 420 250 mm weighing not less than 150 gms 421 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 422 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in-charge. 423 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick 424 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size Kiln seasoned and chemically treated hollock wood 425 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 426 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 427 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 428 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 429 300 x 10mm 430 150 x 10mm 431 Steel Work 432 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 433 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 434 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 435 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. 436 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 437 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 438 Flooring 439 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement 440 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 441 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 442 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of requiredthickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm 443 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm 444 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 445 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 446 P & laying cement concrete 447 Finishing 448 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 449 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 450 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 451 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 452 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 453 Steel Painting:Applying priming coat: 454 With ready mixed aluminium primer of approved brand and manufacture on resinouswood and plywood 455 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 456 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: Two or more coats on new work. 457 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 458 Water Proofing 459 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 460 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 461 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 462 Providing and filling of AAC Lightweight Broken Blocks sunken portions. 463 2.1 Mt high Boundary wall with concertina coil 464 2.1 Mt high Boundary wall 465 PLUMBING INTERNAL ESTIMATE ( 0.375 Unit Girls Dormitory with 3 Nos Warden Residence ) 466 Sub Head– I Sanitary Installation 467 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 468 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 469 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 470 W.C. pan with ISI marked white solid plastic seat and lid 471 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 472 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 473 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 474 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 475 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 476 Providing and fixing toilet paper holder : 477 C.P. brass 478 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 479 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 480 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 481 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 482 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 483 Kitchen sink with drain board 484 510x1040 mm bowl depth 250mm 485 Kitchen sink without drain board 486 610x460 mm bowl depth 200 mm 487 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 488 Size 450x300x150 mm 489 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 490 Flexible pipe 491 40 mm dia 492 Providing and fixing soil, waste and vent pipes : 493 100 mm dia 494 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 495 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 496 100 mm 497 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 498 Providing and fixing plain bend of required degree. 499 100 mm 500 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 501 Providing and fixing heel rest sanitary bend 502 100 mm dia 503 Sand cast iron S&S as per IS - 3989 504 Providing and fixing double equal plain junction of required degree 505 100x100x100x100 mm 506 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 507 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 508 100x100x100 mm 509 sand cast Iron S&S as per IS: 3989 510 Providing and fixing single equal plain junction of required degree 511 100x100x100 mm 512 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 513 Providing and fixing terminal guard: 514 100 mm 515 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 516 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 517 100 mm 518 S S 304 grade coupling with EPDM rubber gasket 519 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 520 100 mm 521 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 522 100 mm diameter pipe 523 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 524 100 mm diameter pipe 525 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 526 32 mm dia. nominal bore 527 40 mm dia. nominal bore 528 50 mm dia. nominal bore 529 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 530 100 mm inlet and 100 mm outlet 531 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 532 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 533 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 534 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 535 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 536 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 537 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 538 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 539 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 540 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 541 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 542 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 543 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 544 Coupler 545 110 mm 546 Single tee with door 547 110x110x110 mm 548 Bend 87.5° 549 110 mm 550 Shoe (Plain) 551 110 mm Shoe 552 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 553 110 mm 554 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 555 110 mm outer dia 556 50 mm outer dia 557 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 558 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 559 Sub Head– II Water Supply 560 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 561 Internal work – Exposed on wall. 562 20 mm nominal outer dia Pipes 563 25 mm nominal outer dia Pipes 564 32 mm nominal outer dia Pipes 565 40 mm nominal outer dia Pipes 566 50 mm nominal outer dia Pipes 567 65 mm nominal outer dia Pipes 568 80 mm nominal outer dia Pipes 569 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 570 Concealed including cutting chases and making good the wall etc. 571 15 mm nominal outer dia Pipes 572 20 mm nominal outer dia Pipes 573 25 mm nominal outer dia Pipes 574 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 575 20 mm dia. nominal bore 576 25 mm dia. nominal bore 577 32 mm dia. nominal bore 578 40 mm dia. nominal bore 579 50 mm dia. nominal bore 580 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 581 25 mm nominal bore 582 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 583 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 584 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 585 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 586 15 mm nominal bore 587 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 588 15 mm nominal bore 589 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 590 15mm nominal bore 591 Providing and fixing uplasticised PVC connection pipe with brass unions : 592 45 cm length 593 15 mm nominal bore 594 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 595 150 mm diameter 596 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 597 (a) 15 mm nominal dia 598 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 599 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 600 upto 50 mm dia. nominal bore 601 SUBHEAD– III Drainage 602 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 603 150 mm diameter 604 200 mm diameter 605 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 606 180x150 mm size P type 607 With fly ash bricks (non modular) bricks of class designation 7.5 608 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 609 150 mm dia. R.C.C. pipe 610 250 mm dia. R.C.C. pipe 611 300 mm dia. R.C.C. pipe 612 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 613 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 614 with common brunt clay FPS ( non modular )bricks of class designation 7.5 615 Extra depth formanhole 90x80 cm 616 With FPSbricks class designation 7.5 617 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 618 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 619 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 620 ELECTRICAL Works 0.375 GIRLS DORMITORY WITH 3 NOS. WARDEN RESIDENCE 621 SUB HEAD - I: CIRCUIT CUM POINT WIRING 622 SWITCH CONTROL LIGHT POINTS 623 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 624 Group C 625 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 626 Group C 627 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 628 Group C 629 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 630 Group C 631 MCB CONTROL LIGHT POINTS 632 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 633 Primary point controlled by one MCB. 634 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 635 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 636 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 637 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 638 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 639 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 640 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 641 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 642 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 643 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 644 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 645 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 646 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 647 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 648 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 649 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 650 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 651 Telephone socket outlet 652 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 653 1 or 2 Module (75mmX75mm) 654 6 module (78mm X 205 mm X 50 mm) 655 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 656 3 pin , 5/6 amps socket outlet 657 5/6 amps switch 658 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 659 25 mm 660 32 mm 661 SUBHEAD -II - FITTINGS & FIXTURES 662 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 663 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 664 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 665 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 666 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 667 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 668 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 669 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 670 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 671 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 672 SUBHEAD - III - DISTRIBUTION BOARDS 673 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 674 6 way, Double door 675 8 way, Double door 676 12 way, Double door 677 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 678 4 way (4 + 12), Double door 679 6 way (4 + 18), Double door 680 8 way (4 + 24), Double door 681 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 682 12 way (4 + 36), Double door 683 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 684 Single Pole 685 Single Pole Neutral 686 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 687 40 A 688 63 A 689 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 690 25 A 691 40 A 692 63 A 693 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 694 25 A 695 40 A 696 63 A 697 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 698 SUB HEAD-IV , LIGHTNING CONDUCTOR 699 LIGHTNING CONDUCTOR 700 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 701 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 702 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 703 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 704 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 705 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 706 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 707 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 708 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 709 [ VICE PRINCIPALRESIDENCE ] (TYPE-4) 710 Earth Work 711 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50 m. 712 All kinds of soil 713 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 714 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 715 Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. 716 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 717 Concrete Work 718 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zoneIII)derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 719 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 720 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 721 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 722 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 723 Reinforced Cement Concrete 724 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 725 Foundations, footings, bases of columns, etc. for mass concrete. 726 Suspended floors, roofs, landings, balconies and access platform. 727 Lintels, beams, plinth beams, girders, bressumers 728 Columns,Pillars, Piers, Abutments, Posts and Struts. 729 Edges of slabs and breaks in floors and walls Under 20 cm wide. 730 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 731 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 732 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 733 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 734 All works upto plinth level 735 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 736 (i) R.C.C. work in Footing 737 (ii) R.C.C. work in Beam 738 (iii) R.C.C. work in Columns 739 All works above plinth level upto floor V level 740 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 741 (i) R.C.C. work in Lintel 742 (ii) R.C.C. work in Beam 743 (iii) R.C.C. work in Columns 744 (iv) R.C.C. work in Slab 745 Masonry Work 746 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 747 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 748 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in superstructure above plinth level up to floor V levelin : 749 Cement mortar 1:6 (1 cement : 6 coarse sand) 750 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) 751 Cladding Work 752 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 753 Area of slab upto 0.50 sqm 754 Area of slab over 0.50 sqm 755 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 756 Granite work 757 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 758 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 759 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 760 Wood and PVC Work 761 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 762 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 763 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 764 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 765 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 766 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous finecellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven selftapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as permanufacturers specification and direction of Engineer-in-charge. 767 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick 768 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size, Kiln seasoned and chemically treated hollock wood 769 3000 Series Windows( Double Rebate with Air Tight Glass Shutter Windows)Providing& Fixing 3000 Series Windows fabricated from roll formed sections made of Galvanized Steel Colour Coated/Powder Coated (Base Steel as per IS 513 “D” quality, Galvanized as per IS 277 with Zinc of 120 grams/Sq. Mtr.) with total coated thickness of 0.60 mm.Paint Specifications:Coated Sections should be with Primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyester Paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyester Powder up to 50-60 microns thick. 770 Dimensions of Sections:Section for Frame should be of 98mm X 50mm, Section for Mullion should be of 46mm X 70mm, Section for Shutter Frame should be of 46mm X 46 mm, Section for Fixed Glass Bead should be of 18mm X 25mm and Section for Fly mesh Shutter Frame should be of 20mm X 40mm.Fixing Details:Frame and Mesh Shutter Sections should be cut to length and mitre joined with Corner Bracket made of Polypropylene. Glass Shutter should be mitre joined with corner brackets made of CRCA electroplated. Mullion Section should be joined with Frame/ Mullion using Nylon Mullion Cap Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter between Frame and Glazed Shutter and both sides of Fixed Glass. Spoon Profile should be used around Fly mesh to fix Mesh in Mesh Shutter. 771 Accessories:Each Glazed Shutter should be provided with MS Powder Coated Friction Hinges – 1 set, High Grade Aluminum Powder Coated Handle -1 No. Each Mesh shutter should be provided with S.S.Pivot Hinges-1 set, Elixir make handle shall be provided per shutter.Window Frame should be fixed to brick/concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Glass: Glass shutter & Fixed Glass portions should be provided with a glass of 4MM Plain Float Glass.MeshMesh Shutter should be provided with a Stainless Steel 32 gauge Fly mesh of 304 grades with 144 holes per square Inch.Grill:-Windows should be provided with Grill made of 10mm sq. MS Bars welded to at 150mm center-to-center, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws. (Make: A2Z Infra Solutions/ Elixir Metform Pvt Ltd./ Lakshmi Fabrications) 772 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 773 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 774 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 775 300 x 10mm 776 150 x 10mm 777 Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer in-charge. 778 Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressedBWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately) 779 Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge. 780 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction ofEngineer-in-charge. 200 mm for CB 781 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction ofEngineer-in-charge. 100 mm for Kitchen Cabinets 782 Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand tocupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete asperdirection of Engineer-in-charge 783 Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge 784 SS Hanging Rod for CB 785 Providing and fixing 25 mm dia. SS pipe Hanging rods with SS brackets : 786 Steel Work 787 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 788 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes (weights not less than 10 kg/ sqm) 789 Flooring 790 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 791 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 792 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laidon 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet forplacing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish ofsize of Tile 600 x 600 mm 793 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm. 794 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 795 Finishing 796 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 797 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 798 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 799 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 800 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 801 Applying priming coat: 802 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 803 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 804 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: 805 Two or more coats on new work. 806 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : Two or more coats on new work 807 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 808 Water Proofing 809 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 810 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 811 PLUMBING INTERNAL ESTIMATE ( Type-4/Vice Principal Residence) 812 Sub Head– I Sanitary Installation 813 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 814 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 815 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 816 W.C. pan with ISI marked white solid plastic seat and lid 817 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 818 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 819 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 820 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 821 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 822 Providing and fixing toilet paper holder : 823 C.P. brass 824 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 825 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 826 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 827 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 828 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 829 Kitchen sink with drain board 830 510x1040 mm bowl depth 250mm 831 Kitchen sink without drain board 832 610x460 mm bowl depth 200 mm 833 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 834 Size 450x300x150 mm 835 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 836 Flexible pipe 837 40 mm dia 838 Providing and fixing soil, waste and vent pipes : 839 100 mm dia 840 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 841 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 842 100 mm 843 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 844 Providing and fixing plain bend of required degree. 845 100 mm 846 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 847 Providing and fixing heel rest sanitary bend 848 100 mm dia 849 Sand cast iron S&S as per IS - 3989 850 Providing and fixing double equal plain junction of required degree 851 100x100x100x100 mm 852 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 853 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 854 100x100x100 mm 855 sand cast Iron S&S as per IS: 3989 856 Providing and fixing single equal plain junction of required degree 857 100x100x100 mm 858 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 859 Providing and fixing terminal guard: 860 100 mm 861 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 862 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 863 100 mm 864 S S 304 grade coupling with EPDM rubber gasket 865 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 866 100 mm 867 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 868 100 mm diameter pipe 869 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 870 100 mm diameter pipe 871 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 872 32 mm dia. nominal bore 873 40 mm dia. nominal bore 874 50 mm dia. nominal bore 875 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 876 100 mm inlet and 100 mm outlet 877 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 878 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 879 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 880 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 881 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 882 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 883 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 884 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 885 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 886 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 887 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 888 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 889 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 890 Coupler 891 110 mm 892 Single tee with door 893 110x110x110 mm 894 Bend 87.5° 895 110 mm 896 Shoe (Plain) 897 110 mm Shoe 898 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 899 110 mm 900 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 901 110 mm outer dia 902 50 mm outer dia 903 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 904 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 905 Sub Head– II Water Supply 906 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 907 Internal work – Exposed on wall. 908 20 mm nominal outer dia Pipes 909 25 mm nominal outer dia Pipes 910 32 mm nominal outer dia Pipes 911 40 mm nominal outer dia Pipes 912 50 mm nominal outer dia Pipes 913 65 mm nominal outer dia Pipes 914 80 mm nominal outer dia Pipes 915 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 916 Concealed including cutting chases and making good the wall etc. 917 15 mm nominal outer dia Pipes 918 20 mm nominal outer dia Pipes 919 25 mm nominal outer dia Pipes 920 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 921 20 mm dia. nominal bore 922 25 mm dia. nominal bore 923 32 mm dia. nominal bore 924 40 mm dia. nominal bore 925 50 mm dia. nominal bore 926 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 927 25 mm nominal bore 928 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 929 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 930 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 931 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 932 15 mm nominal bore 933 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 934 15 mm nominal bore 935 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 936 15mm nominal bore 937 Providing and fixing uplasticised PVC connection pipe with brass unions : 938 45 cm length 939 15 mm nominal bore 940 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 941 150 mm diameter 942 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 943 (a) 15 mm nominal dia 944 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 945 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 946 upto 50 mm dia. nominal bore 947 SUBHEAD– III Drainage 948 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 949 150 mm diameter 950 200 mm diameter 951 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 952 180x150 mm size P type 953 With fly ash bricks (non modular) bricks of class designation 7.5 954 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 955 150 mm dia. R.C.C. pipe 956 250 mm dia. R.C.C. pipe 957 300 mm dia. R.C.C. pipe 958 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 959 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 960 with common brunt clay FPS ( non modular )bricks of class designation 7.5 961 Extra depth formanhole 90x80 cm 962 With FPSbricks class designation 7.5 963 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 964 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 965 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 966 ELECTRICAL Works TYPE - 4 RESIDENCE (VICE PRINCIPAL RESIDENCE) 967 SUB HEAD - I: CIRCUIT CUM POINT WIRING 968 SWITCH CONTROL LIGHT POINTS 969 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 970 Group C 971 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 972 Group C 973 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 974 Group C 975 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 976 Group C 977 MCB CONTROL LIGHT POINTS 978 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 979 Primary point controlled by one MCB. 980 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 981 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 982 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 983 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 984 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 985 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 986 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 987 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 988 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 989 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 990 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 991 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 992 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 993 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 994 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 995 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 996 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 997 Telephone socket outlet 998 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 999 1 or 2 Module (75mmX75mm) 1000 6 module (78mm X 205 mm X 50 mm) 1001 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1002 3 pin , 5/6 amps socket outlet 1003 5/6 amps switch 1004 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1005 25 mm 1006 32 mm 1007 SUBHEAD -II - FITTINGS & FIXTURES 1008 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 1009 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 1010 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 1011 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 1012 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 1013 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 1014 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 1015 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 1016 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1017 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 1018 SUBHEAD - III - DISTRIBUTION BOARDS 1019 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 1020 6 way, Double door 1021 8 way, Double door 1022 12 way, Double door 1023 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 1024 4 way (4 + 12), Double door 1025 6 way (4 + 18), Double door 1026 8 way (4 + 24), Double door 1027 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 1028 12 way (4 + 36), Double door 1029 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1030 Single Pole 1031 Single Pole Neutral 1032 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1033 40 A 1034 63 A 1035 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1036 25 A 1037 40 A 1038 63 A 1039 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1040 25 A 1041 40 A 1042 63 A 1043 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 1044 SUB HEAD-IV , LIGHTNING CONDUCTOR 1045 LIGHTNING CONDUCTOR 1046 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 1047 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 1048 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 1049 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 1050 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1051 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1052 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 1053 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 1054 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 1055 [ TYPE-III RESIDENCES G+2, 6UNITS. ] 1056 Earth Work 1057 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50 m. 1058 All kinds of soil 1059 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 1060 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 1061 Supplying and filling in plinth with sand under floors, including watering, ramming ,consolidating and dressing complete. 1062 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 1063 Concrete Work 1064 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 1065 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 1066 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 1067 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 1068 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 1069 Reinforced Cement Concrete 1070 Centering and shuttering including strutting, propping etc. and removal of form for all heights 1071 Foundations, footings, bases of columns, etc. for mass concrete. 1072 Suspended floors, roofs, landings, balconies and access platform. 1073 Lintels, beams, plinth beams, girders, bressumers 1074 Columns,Pillars, Piers, Abutments, Posts and Struts. 1075 Edges of slabs and breaks in floors and walls Under 20 cm wide. 1076 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 1077 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 1078 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 1079 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength;including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of theminimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 1080 All works upto plinth level 1081 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 1082 (i) R.C.C. work in Footing 1083 (ii) R.C.C. work in Beam 1084 (iii) R.C.C. work in Columns 1085 All works above plinth level upto floor V level 1086 Concrete of M25 grade with minimum cement content of 330 kg /cum 1087 (i) R.C.C. work in Lintel 1088 (ii) R.C.C. work in Beam 1089 (iii) R.C.C. work in Columns 1090 (iv) R.C.C. work in Slab 1091 Masonry Work 1092 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. : cement mortar 1:4 (1 cement : 4 coarse sand) 1093 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 1094 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand) 1095 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 1096 Cladding Work 1097 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 1098 Granite stone slab colour black, Cherry/Ruby red 1099 Area of slab upto 0.50 sqm 1100 Area of slab over 0.50 sqm 1101 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1102 Granite work 1103 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 1104 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1105 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1106 Wood and PVC Work 1107 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI markedStainless Steel butt hinges with necessary screws 1108 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 1109 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 1110 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 1111 300 mm weighing not less than 200 gms 1112 250 mm weighing not less than 150 gms 1113 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 1114 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous finecellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven selftapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as permanufacturers specification and direction of Engineer-in-charge. 1115 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick 1116 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size 1117 Kiln seasoned and chemically treated hollock wood 1118 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 1119 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 1120 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 1121 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 1122 300 x 10mm 1123 150 x 10mm 1124 Steel Work 1125 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 1126 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 1127 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1128 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 1129 SS RALING 1130 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. 1131 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 1132 Flooring 1133 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 1134 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1135 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm 1136 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.size of tile 600x600 mm 1137 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 1138 Finishing 1139 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 1140 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 1141 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 1142 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 1143 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 1144 Steel Painting:Applying priming coat 1145 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 1146 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 1147 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: 1148 Two or more coats on new work. 1149 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1150 Water Proofing 1151 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 1152 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 1153 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 1154 Providing and filling of AAC Lightweight Broken Blocks sunken portions. 1155 PLUMBING INTERNAL ESTIMATE ( Type-3 ,6 Unit ) (G+2) 1156 Sub Head– I Sanitary Installation 1157 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 1158 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 1159 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1160 W.C. pan with ISI marked white solid plastic seat and lid 1161 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 1162 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 1163 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 1164 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 1165 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 1166 Providing and fixing toilet paper holder : 1167 C.P. brass 1168 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 1169 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 1170 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 1171 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1172 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 1173 Kitchen sink with drain board 1174 510x1040 mm bowl depth 250mm 1175 Kitchen sink without drain board 1176 610x460 mm bowl depth 200 mm 1177 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 1178 Size 450x300x150 mm 1179 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 1180 Flexible pipe 1181 40 mm dia 1182 Providing and fixing soil, waste and vent pipes : 1183 100 mm dia 1184 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 1185 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1186 100 mm 1187 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 1188 Providing and fixing plain bend of required degree. 1189 100 mm 1190 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1191 Providing and fixing heel rest sanitary bend 1192 100 mm dia 1193 Sand cast iron S&S as per IS - 3989 1194 Providing and fixing double equal plain junction of required degree 1195 100x100x100x100 mm 1196 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1197 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1198 100x100x100 mm 1199 sand cast Iron S&S as per IS: 3989 1200 Providing and fixing single equal plain junction of required degree 1201 100x100x100 mm 1202 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1203 Providing and fixing terminal guard: 1204 100 mm 1205 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1206 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 1207 100 mm 1208 S S 304 grade coupling with EPDM rubber gasket 1209 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 1210 100 mm 1211 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 1212 100 mm diameter pipe 1213 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 1214 100 mm diameter pipe 1215 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1216 32 mm dia. nominal bore 1217 40 mm dia. nominal bore 1218 50 mm dia. nominal bore 1219 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 1220 100 mm inlet and 100 mm outlet 1221 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 1222 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 1223 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 1224 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 1225 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 1226 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 1227 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 1228 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 1229 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 1230 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1231 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1232 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 1233 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 1234 Coupler 1235 110 mm 1236 Single tee with door 1237 110x110x110 mm 1238 Bend 87.5° 1239 110 mm 1240 Shoe (Plain) 1241 110 mm Shoe 1242 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1243 110 mm 1244 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 1245 110 mm outer dia 1246 50 mm outer dia 1247 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 1248 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 1249 Sub Head– II Water Supply 1250 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1251 Internal work – Exposed on wall. 1252 20 mm nominal outer dia Pipes 1253 25 mm nominal outer dia Pipes 1254 32 mm nominal outer dia Pipes 1255 40 mm nominal outer dia Pipes 1256 50 mm nominal outer dia Pipes 1257 65 mm nominal outer dia Pipes 1258 80 mm nominal outer dia Pipes 1259 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1260 Concealed including cutting chases and making good the wall etc. 1261 15 mm nominal outer dia Pipes 1262 20 mm nominal outer dia Pipes 1263 25 mm nominal outer dia Pipes 1264 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1265 20 mm dia. nominal bore 1266 25 mm dia. nominal bore 1267 32 mm dia. nominal bore 1268 40 mm dia. nominal bore 1269 50 mm dia. nominal bore 1270 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1271 25 mm nominal bore 1272 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 1273 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 1274 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 1275 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1276 15 mm nominal bore 1277 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1278 15 mm nominal bore 1279 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1280 15mm nominal bore 1281 Providing and fixing uplasticised PVC connection pipe with brass unions : 1282 45 cm length 1283 15 mm nominal bore 1284 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 1285 150 mm diameter 1286 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 1287 (a) 15 mm nominal dia 1288 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 1289 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 1290 upto 50 mm dia. nominal bore 1291 SUBHEAD– III Drainage 1292 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 1293 150 mm diameter 1294 200 mm diameter 1295 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 1296 180x150 mm size P type 1297 With fly ash bricks (non modular) bricks of class designation 7.5 1298 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 1299 150 mm dia. R.C.C. pipe 1300 250 mm dia. R.C.C. pipe 1301 300 mm dia. R.C.C. pipe 1302 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 1303 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 1304 with common brunt clay FPS ( non modular )bricks of class designation 7.5 1305 Extra depth formanhole 90x80 cm 1306 With FPSbricks class designation 7.5 1307 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 1308 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 1309 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1310 ELECTRICAL Works TYPE-3 (G+2) RESIDENCE 1311 SUB HEAD - I: CIRCUIT CUM POINT WIRING 1312 SWITCH CONTROL LIGHT POINTS 1313 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1314 Group C 1315 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 1316 Group C 1317 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 1318 Group C 1319 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 1320 Group C 1321 MCB CONTROL LIGHT POINTS 1322 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 1323 Primary point controlled by one MCB. 1324 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 1325 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 1326 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 1327 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 1328 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 1329 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 1330 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 1331 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 1332 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 1333 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 1334 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 1335 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 1336 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 1337 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 1338 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 1339 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 1340 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1341 Telephone socket outlet 1342 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1343 1 or 2 Module (75mmX75mm) 1344 6 module (78mm X 205 mm X 50 mm) 1345 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1346 3 pin , 5/6 amps socket outlet 1347 5/6 amps switch 1348 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1349 25 mm 1350 32 mm 1351 SUBHEAD -II - FITTINGS & FIXTURES 1352 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 1353 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 1354 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 1355 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 1356 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 1357 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 1358 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 1359 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 1360 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1361 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 1362 SUBHEAD - III - DISTRIBUTION BOARDS 1363 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 1364 6 way, Double door 1365 8 way, Double door 1366 12 way, Double door 1367 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 1368 4 way (4 + 12), Double door 1369 6 way (4 + 18), Double door 1370 8 way (4 + 24), Double door 1371 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 1372 12 way (4 + 36), Double door 1373 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1374 Single Pole 1375 Single Pole Neutral 1376 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1377 40 A 1378 63 A 1379 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1380 25 A 1381 40 A 1382 63 A 1383 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1384 25 A 1385 40 A 1386 63 A 1387 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 1388 SUB HEAD-IV , LIGHTNING CONDUCTOR 1389 LIGHTNING CONDUCTOR 1390 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 1391 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 1392 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 1393 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 1394 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1395 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1396 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 1397 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 1398 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 1399 [ TYPE-II RESIDENCES G+2, 6 UNITS. ] 1400 Earth Work 1401 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1402 All kinds of soil 1403 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 1404 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.All kinds of soil 1405 Supplying and filling in plinth with sand under floors, including watering, ramming ,consolidating and dressing complete. 1406 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 1407 Concrete Work 1408 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zoneIII)derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 1409 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 1410 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 1411 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 1412 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 1413 Reinforced Cement Concrete 1414 Centering and shuttering including strutting, propping etc. and removal of form for all heights 1415 Foundations, footings, bases of columns, etc. for mass concrete. 1416 Suspended floors, roofs, landings, balconies and access platform. 1417 Lintels, beams, plinth beams, girders, bressumers 1418 Columns,Pillars, Piers, Abutments, Posts and Struts. 1419 Edges of slabs and breaks in floors and walls Under 20 cm wide. 1420 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 1421 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 1422 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 1423 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength;including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of theminimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 1424 All works upto plinth level 1425 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 1426 (i) R.C.C. work in Footing 1427 (ii) R.C.C. work in Beam 1428 (iii) R.C.C. work in Columns 1429 All works above plinth level upto floor V level 1430 Concrete of M25 grade with minimum cement content of 330 kg /cum 1431 (i) R.C.C. work in Lintel 1432 (ii) R.C.C. work in Beam 1433 (iii) R.C.C. work in Columns 1434 (iv) R.C.C. work in Slab 1435 Masonry Work 1436 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. : cement mortar 1:4 (1 cement : 4 coarse sand) 1437 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 1438 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand) 1439 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) 1440 Cladding Work 1441 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 1442 Granite stone slab colour black, Cherry/Ruby red 1443 Area of slab upto 0.50 sqm 1444 Area of slab over 0.50 sqm 1445 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1446 Granite work 1447 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 1448 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1449 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1450 Wood and PVC Work 1451 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI markedStainless Steel butt hinges with necessary screws 1452 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 1453 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 1454 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 1455 300 mm weighing not less than 200 gms 1456 250 mm weighing not less than 150 gms 1457 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 1458 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in-charge. 1459 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesivebonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick 1460 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size 1461 Kiln seasoned and chemically treated hollock wood 1462 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 1463 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 1464 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 1465 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 1466 300 x 10mm 1467 150 x 10mm 1468 Steel Work 1469 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 1470 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 1471 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1472 SS RALING 1473 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. 1474 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 1475 Flooring 1476 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 1477 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1478 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm 1479 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.size of tile 600x600 mm 1480 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 1481 Finishing 1482 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 1483 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 1484 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 1485 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 1486 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 1487 Steel Painting:Applying priming coat 1488 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 1489 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 1490 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: 1491 Two or more coats on new work. 1492 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1493 Water Proofing 1494 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 1495 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 1496 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 1497 Providing and filling of AAC Lightweight Broken Blocks sunken portions. 1498 PLUMBING INTERNAL ESTIMATE ( Type-2,6 Nos.) G+2 1499 Sub Head– I Sanitary Installation 1500 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 1501 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 1502 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1503 W.C. pan with ISI marked white solid plastic seat and lid 1504 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 1505 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 1506 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 1507 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 1508 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 1509 Providing and fixing toilet paper holder : 1510 C.P. brass 1511 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 1512 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 1513 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 1514 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1515 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 1516 Kitchen sink with drain board 1517 510x1040 mm bowl depth 250mm 1518 Kitchen sink without drain board 1519 610x460 mm bowl depth 200 mm 1520 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 1521 Size 450x300x150 mm 1522 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 1523 Flexible pipe 1524 40 mm dia 1525 Providing and fixing soil, waste and vent pipes : 1526 100 mm dia 1527 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 1528 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1529 100 mm 1530 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 1531 Providing and fixing plain bend of required degree. 1532 100 mm 1533 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1534 Providing and fixing heel rest sanitary bend 1535 100 mm dia 1536 Sand cast iron S&S as per IS - 3989 1537 Providing and fixing double equal plain junction of required degree 1538 100x100x100x100 mm 1539 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1540 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1541 100x100x100 mm 1542 sand cast Iron S&S as per IS: 3989 1543 Providing and fixing single equal plain junction of required degree 1544 100x100x100 mm 1545 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1546 Providing and fixing terminal guard: 1547 100 mm 1548 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1549 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 1550 100 mm 1551 S S 304 grade coupling with EPDM rubber gasket 1552 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 1553 100 mm 1554 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 1555 100 mm diameter pipe 1556 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 1557 100 mm diameter pipe 1558 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1559 32 mm dia. nominal bore 1560 40 mm dia. nominal bore 1561 50 mm dia. nominal bore 1562 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 1563 100 mm inlet and 100 mm outlet 1564 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 1565 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 1566 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 1567 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 1568 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 1569 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 1570 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 1571 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 1572 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 1573 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1574 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1575 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 110 mm dia 1576 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 1577 Coupler 1578 110 mm 1579 Single tee with door 1580 110x110x110 mm 1581 Bend 87.5° 1582 110 mm 1583 Shoe (Plain) 1584 110 mm Shoe 1585 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1586 110 mm 1587 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 1588 110 mm outer dia 1589 50 mm outer dia 1590 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 1591 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 1592 Sub Head– II Water Supply 1593 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1594 Internal work – Exposed on wall. 1595 20 mm nominal outer dia Pipes 1596 25 mm nominal outer dia Pipes 1597 32 mm nominal outer dia Pipes 1598 40 mm nominal outer dia Pipes 1599 50 mm nominal outer dia Pipes 1600 65 mm nominal outer dia Pipes 1601 80 mm nominal outer dia Pipes 1602 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1603 Concealed including cutting chases and making good the wall etc. 1604 15 mm nominal outer dia Pipes 1605 20 mm nominal outer dia Pipes 1606 25 mm nominal outer dia Pipes 1607 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1608 20 mm dia. nominal bore 1609 25 mm dia. nominal bore 1610 32 mm dia. nominal bore 1611 40 mm dia. nominal bore 1612 50 mm dia. nominal bore 1613 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1614 25 mm nominal bore 1615 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 1616 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 1617 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 1618 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1619 15 mm nominal bore 1620 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1621 15 mm nominal bore 1622 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1623 15mm nominal bore 1624 Providing and fixing uplasticised PVC connection pipe with brass unions : 1625 45 cm length 1626 15 mm nominal bore 1627 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 1628 150 mm diameter 1629 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 1630 (a) 15 mm nominal dia 1631 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 1632 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 1633 upto 50 mm dia. nominal bore 1634 SUBHEAD– III Drainage 1635 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 1636 150 mm diameter 1637 200 mm diameter 1638 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 1639 180x150 mm size P type 1640 With fly ash bricks (non modular) bricks of class designation 7.5 1641 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 1642 150 mm dia. R.C.C. pipe 1643 250 mm dia. R.C.C. pipe 1644 300 mm dia. R.C.C. pipe 1645 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 1646 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 1647 with common brunt clay FPS ( non modular )bricks of class designation 7.5 1648 Extra depth formanhole 90x80 cm 1649 With FPSbricks class designation 7.5 1650 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 1651 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 1652 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1653 ELECTRICAL Works TYPE-2 (G+2) RESIDENCE 6 Nos 1654 SUB HEAD - I: CIRCUIT CUM POINT WIRING 1655 SWITCH CONTROL LIGHT POINTS 1656 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1657 Group C 1658 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 1659 Group C 1660 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 1661 Group C 1662 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 1663 Group C 1664 MCB CONTROL LIGHT POINTS 1665 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 1666 Primary point controlled by one MCB. 1667 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 1668 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 1669 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 1670 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 1671 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 1672 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 1673 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 1674 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 1675 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 1676 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 1677 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 1678 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 1679 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 1680 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 1681 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 1682 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 1683 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1684 Telephone socket outlet 1685 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1686 1 or 2 Module (75mmX75mm) 1687 6 module (78mm X 205 mm X 50 mm) 1688 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1689 3 pin , 5/6 amps socket outlet 1690 5/6 amps switch 1691 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1692 25 mm 1693 32 mm 1694 SUBHEAD -II - FITTINGS & FIXTURES 1695 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 1696 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 1697 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 1698 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 1699 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 1700 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 1701 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 1702 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 1703 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1704 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 1705 SUBHEAD - III - DISTRIBUTION BOARDS 1706 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 1707 6 way, Double door 1708 8 way, Double door 1709 12 way, Double door 1710 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 1711 4 way (4 + 12), Double door 1712 6 way (4 + 18), Double door 1713 8 way (4 + 24), Double door 1714 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 1715 12 way (4 + 36), Double door 1716 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1717 Single Pole 1718 Single Pole Neutral 1719 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1720 40 A 1721 63 A 1722 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1723 25 A 1724 40 A 1725 63 A 1726 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1727 25 A 1728 40 A 1729 63 A 1730 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 1731 SUB HEAD-IV , LIGHTNING CONDUCTOR 1732 LIGHTNING CONDUCTOR 1733 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 1734 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 1735 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 1736 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 1737 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1738 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1739 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 1740 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 1741 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 1742 [ TYPE-II RESIDENCES Single Storey, 1UNIT. ] 1743 Earth Work 1744 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1745 All kinds of soil 1746 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 1747 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.All kinds of soil 1748 Supplying and filling in plinth with sand under floors, including watering, ramming ,consolidating and dressing complete. 1749 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 1750 Concrete Work 1751 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand (zoneIII)derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 1752 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 1753 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 1754 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 1755 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 1756 Reinforced Cement Concrete 1757 Centering and shuttering including strutting, propping etc. and removal of form for all heights 1758 Foundations, footings, bases of columns, etc. for mass concrete. 1759 Suspended floors, roofs, landings, balconies and access platform. 1760 Lintels, beams, plinth beams, girders, bressumers 1761 Columns,Pillars, Piers, Abutments, Posts and Struts. 1762 Edges of slabs and breaks in floors and walls Under 20 cm wide. 1763 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 1764 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 1765 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 1766 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength;including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of theminimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 1767 All works upto plinth level 1768 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 1769 (i) R.C.C. work in Footing 1770 (ii) R.C.C. work in Beam 1771 (iii) R.C.C. work in Columns 1772 All works above plinth level upto floor V level 1773 Concrete of M25 grade with minimum cement content of 330 kg /cum 1774 (i) R.C.C. work in Lintel 1775 (ii) R.C.C. work in Beam 1776 (iii) R.C.C. work in Columns 1777 (iv) R.C.C. work in Slab 1778 Masonry Work 1779 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. : cement mortar 1:4 (1 cement : 4 coarse sand) 1780 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 1781 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand) 1782 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 1783 Cladding Work 1784 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 1785 Granite stone slab colour black, Cherry/Ruby red 1786 Area of slab upto 0.50 sqm 1787 Area of slab over 0.50 sqm 1788 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1789 Granite work 1790 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 1791 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1792 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy,bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointingwith grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1793 Wood and PVC Work 1794 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI markedStainless Steel butt hinges with necessary screws 1795 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 1796 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 1797 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 1798 300 mm weighing not less than 200 gms 1799 250 mm weighing not less than 150 gms 1800 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 1801 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of Engineer-in-charge. 1802 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick 1803 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 1804 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 1805 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 1806 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 1807 300 x 10mm 1808 150 x 10mm 1809 Steel Work 1810 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 1811 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 1812 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1813 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 1814 Flooring 1815 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 1816 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1817 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm 1818 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.size of tile 600x600 mm 1819 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 1820 Finishing 1821 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 1822 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 1823 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 1824 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 1825 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 1826 Steel Painting:Applying priming coat 1827 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 1828 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 1829 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: 1830 Two or more coats on new work. 1831 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1832 Water Proofing 1833 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 1834 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 1835 PLUMBING INTERNAL ESTIMATE (Type- 2 Single unit) 1836 Sub Head– I Sanitary Installation 1837 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 1838 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 1839 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1840 W.C. pan with ISI marked white solid plastic seat and lid 1841 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 1842 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 1843 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 1844 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 1845 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 1846 Providing and fixing toilet paper holder : 1847 C.P. brass 1848 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 1849 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 1850 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 1851 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1852 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 1853 Kitchen sink with drain board 1854 510x1040 mm bowl depth 250mm 1855 Kitchen sink without drain board 1856 610x460 mm bowl depth 200 mm 1857 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 1858 Size 450x300x150 mm 1859 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 1860 Flexible pipe 1861 40 mm dia 1862 Providing and fixing soil, waste and vent pipes : 1863 100 mm dia 1864 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 1865 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1866 100 mm 1867 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 1868 Providing and fixing plain bend of required degree. 1869 100 mm 1870 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1871 Providing and fixing heel rest sanitary bend 1872 100 mm dia 1873 Sand cast iron S&S as per IS - 3989 1874 Providing and fixing double equal plain junction of required degree 1875 100x100x100x100 mm 1876 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1877 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1878 100x100x100 mm 1879 sand cast Iron S&S as per IS: 3989 1880 Providing and fixing single equal plain junction of required degree 1881 100x100x100 mm 1882 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1883 Providing and fixing terminal guard: 1884 100 mm 1885 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 1886 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 1887 100 mm 1888 S S 304 grade coupling with EPDM rubber gasket 1889 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 1890 100 mm 1891 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 1892 100 mm diameter pipe 1893 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 1894 100 mm diameter pipe 1895 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1896 32 mm dia. nominal bore 1897 40 mm dia. nominal bore 1898 50 mm dia. nominal bore 1899 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 1900 100 mm inlet and 100 mm outlet 1901 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 1902 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 1903 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 1904 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 1905 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 1906 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 1907 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 1908 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 1909 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 1910 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1911 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1912 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 110 mm dia 1913 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 1914 Coupler 1915 110 mm 1916 Single tee with door 1917 110x110x110 mm 1918 Bend 87.5° 1919 110 mm 1920 Shoe (Plain) 1921 110 mm Shoe 1922 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1923 110 mm 1924 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 1925 110 mm outer dia 1926 50 mm outer dia 1927 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 1928 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 1929 Sub Head– II Water Supply 1930 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 1931 Internal work – Exposed on wall. 1932 20 mm nominal outer dia Pipes 1933 25 mm nominal outer dia Pipes 1934 32 mm nominal outer dia Pipes 1935 40 mm nominal outer dia Pipes 1936 50 mm nominal outer dia Pipes 1937 65 mm nominal outer dia Pipes 1938 80 mm nominal outer dia Pipes 1939 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1940 Concealed including cutting chases and making good the wall etc. 1941 15 mm nominal outer dia Pipes 1942 20 mm nominal outer dia Pipes 1943 25 mm nominal outer dia Pipes 1944 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1945 20 mm dia. nominal bore 1946 25 mm dia. nominal bore 1947 32 mm dia. nominal bore 1948 40 mm dia. nominal bore 1949 50 mm dia. nominal bore 1950 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1951 25 mm nominal bore 1952 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 1953 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 1954 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 1955 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1956 15 mm nominal bore 1957 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1958 15 mm nominal bore 1959 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1960 15mm nominal bore 1961 Providing and fixing uplasticised PVC connection pipe with brass unions : 1962 45 cm length 1963 15 mm nominal bore 1964 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 1965 150 mm diameter 1966 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 1967 (a) 15 mm nominal dia 1968 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 1969 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 1970 upto 50 mm dia. nominal bore 1971 SUBHEAD– III Drainage 1972 Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098( Part - 2 ) 3013 for soil / waste pipe under ground drainage system withjointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 1973 150 mm diameter 1974 200 mm diameter 1975 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brickmasonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design : 1976 180x150 mm size P type 1977 With fly ash bricks (non modular) bricks of class designation 7.5 1978 Providingandlayingnon-pressureNP2class(lightduty)R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 1979 150 mm dia. R.C.C. pipe 1980 250 mm dia. R.C.C. pipe 1981 300 mm dia. R.C.C. pipe 1982 Constructing brick masonry manholein cement mortar 1:4 (1 cement :4 coarse sand)with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size )inside plastering12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cementcomplete as per standard design . 1983 inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg ) 1984 with common brunt clay FPS ( non modular )bricks of class designation 7.5 1985 Extra depth formanhole 90x80 cm 1986 With FPSbricks class designation 7.5 1987 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequeringesides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 1988 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 1989 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1990 ELECTRICAL Works TYPE-2Single unit 1991 SUB HEAD - I: CIRCUIT CUM POINT WIRING 1992 SWITCH CONTROL LIGHT POINTS 1993 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1994 Group C 1995 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 1996 Group C 1997 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 1998 Group C 1999 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 2000 Group C 2001 MCB CONTROL LIGHT POINTS 2002 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 2003 Primary point controlled by one MCB. 2004 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 2005 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 2006 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2007 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 2008 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2009 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 2010 2 x 10 sq. mm + 1 x 10 sq.mm earth wire 2011 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 2012 4 X 16 sq. mm + 2 X 6 sq. mm earth wire 2013 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 2014 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 2015 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 2016 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 2017 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 2018 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 2019 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 2020 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2021 Telephone socket outlet 2022 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2023 1 or 2 Module (75mmX75mm) 2024 6 module (78mm X 205 mm X 50 mm) 2025 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2026 3 pin , 5/6 amps socket outlet 2027 5/6 amps switch 2028 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 2029 25 mm 2030 32 mm 2031 SUBHEAD -II - FITTINGS & FIXTURES 2032 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 2033 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 2034 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 2035 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 2036 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 2037 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 2038 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 2039 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 2040 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 2041 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 2042 SUBHEAD - III - DISTRIBUTION BOARDS 2043 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2044 6 way, Double door 2045 8 way, Double door 2046 12 way, Double door 2047 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 2048 4 way (4 + 12), Double door 2049 6 way (4 + 18), Double door 2050 8 way (4 + 24), Double door 2051 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 2052 12 way (4 + 36), Double door 2053 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2054 Single Pole 2055 Single Pole Neutral 2056 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2057 40 A 2058 63 A 2059 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2060 25 A 2061 40 A 2062 63 A 2063 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2064 25 A 2065 40 A 2066 63 A 2067 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 2068 SUB HEAD-IV , LIGHTNING CONDUCTOR 2069 LIGHTNING CONDUCTOR 2070 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 2071 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 2072 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 2073 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 2074 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2075 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2076 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 2077 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 2078 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 2079 [GUEST HOUSE ] 2080 Earth Work 2081 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2082 All kinds of soil 2083 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 2084 Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil 2085 Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete. 2086 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 2087 Concrete Work 2088 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:5:10 (1 Cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2089 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) 2090 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 2091 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,including necessary excavation,levelling & dressing & finishing the top smooth. 2092 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 2093 Reinforced Cement Concrete 2094 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 2095 Foundations, footings, bases of columns, etc. for mass concrete. 2096 Suspended floors, roofs, landings, balconies and access platform. 2097 Lintels, beams, plinth beams, girders, bressumers 2098 Columns,Pillars, Piers, Abutments, Posts and Struts. 2099 Edges of slabs and breaks in floors and walls Under 20 cm wide. 2100 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 2101 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 2102 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 2103 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarseaggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures inrecommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairingstrength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement contentin design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 2104 All works upto plinth level 2105 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 2106 (i) R.C.C. work in Footing 2107 (ii) R.C.C. work in Beam 2108 (iii) R.C.C. work in Columns 2109 All works above plinth level upto floor V level 2110 Concrete of M25 grade with minimum cementcontent of 330 kg /cum 2111 (i) R.C.C. work in Lintel 2112 (ii) R.C.C. work in Beam 2113 (iii) R.C.C. work in Columns 2114 (iv) R.C.C. work in Slab 2115 Masonry Work 2116 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 2117 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 2118 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in superstructure above plinth level up to floor V levelin : 2119 Cement mortar 1:6 (1 cement : 6 coarse sand) 2120 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) 2121 Cladding Work 2122 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointinwith grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 2123 Wood and PVC Work 2124 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on bothfaces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 2125 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 2126 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 2127 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 2128 300 mm weighing not less than 200 gms 2129 250 mm weighing not less than 150 gms 2130 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 2131 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous finecellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven selftapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as permanufacturers specification and direction of Engineer-in-charge. 2132 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick 2133 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size, Kiln seasoned and chemically treated hollock wood 2134 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.With 12 mm mild steel U beading 2135 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 125 mm. 2136 Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . 2137 Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. 2138 300 x 10mm 2139 150 x 10mm 2140 Steel Work 2141 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 2142 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 2143 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 2144 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 2145 Flooring 2146 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 2147 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 2148 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laidon 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet forplacing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish ofsize of Tile 600 x 600 mm 2149 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm. 2150 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 2151 Finishing 2152 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand) 2153 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) 2154 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 2155 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 2156 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 2157 Applying priming coat: 2158 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 2159 With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 2160 Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade: 2161 Two or more coats on new work. 2162 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2163 Water Proofing 2164 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 2165 Providing and laying brick tiles over mumty roofs, grouted with cementmortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat:With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 2166 PLUMBING INTERNAL ESTIMATE (Guest House ) 2167 Sub Head– I Sanitary Installation 2168 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:. 2169 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. 2170 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 2171 W.C. pan with ISI marked white solid plastic seat and lid 2172 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 2173 Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification anddirection of Engineer-in-charge. 2174 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 2175 White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps 2176 Providing and fixingwhite vitreous china wash basin under counter basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, includingpainting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge 2177 Providing and fixing toilet paper holder : 2178 C.P. brass 2179 ProvidingandfixingCPbrassauto closing system basin pillartap / hand washofJaquar PRS - 001 or EquivalentasapprovedbyEngineer-In Charge 2180 ProvidingandfixingCPbrasssingle lever basin mixerwithout popowith 450mm long braided hose (connection pipe)basin pillartapofJaquar LYR-38001B or EquivalentasapprovedbyEngineer-In Charge. 2181 Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. 2182 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 2183 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever required : 2184 Kitchen sink with drain board 2185 510x1040 mm bowl depth 250mm 2186 Kitchen sink without drain board 2187 610x460 mm bowl depth 200 mm 2188 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : 2189 Size 450x300x150 mm 2190 Providing and fixing P.V.C. waste pipe for sinkor wash basin including P.V.C. waste fittings complete. 2191 Flexible pipe 2192 40 mm dia 2193 Providing and fixing soil, waste and vent pipes : 2194 100 mm dia 2195 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 2196 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 2197 100 mm 2198 Hubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 2199 Providing and fixing plain bend of required degree. 2200 100 mm 2201 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 2202 Providing and fixing heel rest sanitary bend 2203 100 mm dia 2204 Sand cast iron S&S as per IS - 3989 2205 Providing and fixing double equal plain junction of required degree 2206 100x100x100x100 mm 2207 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 2208 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 2209 100x100x100 mm 2210 sand cast Iron S&S as per IS: 3989 2211 Providing and fixing single equal plain junction of required degree 2212 100x100x100 mm 2213 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 2214 Providing and fixing terminal guard: 2215 100 mm 2216 Hubless centrifugally cast (spun) iron pipe epoxy inside & outsideIS: 15905 2217 Providingand fixing shielded coupling for Hubless centrifugally cast iron pipes 2218 100 mm 2219 S S 304 grade coupling with EPDM rubber gasket 2220 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 2221 100 mm 2222 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 2223 100 mm diameter pipe 2224 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : 2225 100 mm diameter pipe 2226 Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 2227 32 mm dia. nominal bore 2228 40 mm dia. nominal bore 2229 50 mm dia. nominal bore 2230 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 2231 100 mm inlet and 100 mm outlet 2232 Hubless centrifugally cast (spun) iron epoxycoated inside & outside as per IS:15905 2233 Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 Cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size ) , including finishing complete so as to make it leak proof. 2234 Providing & fixing in position GI 100x50 elbowfloor drainincluding cost of cutting and making good the walls and floors whereverrequired. 2235 Providingandfixing125mmdiaS/S grating(withorwithouthole)for floor or Nahani trap. 2236 Providing and fixing soap dish holderfrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1131N & Equivalent 2237 Providing and fixing soap dispenser with glass bottlefrom wall of standard shape withfittings of approved quality with all complete. Make Jaquar - ACN-1135N & Equivalent 2238 Providing & fixing600 mm towel rail long stanless steel from wall face with concealedfittings arrangement of approved quality with all complete. Make Jaquar - CAN-1111SM 2239 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 2240 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 2241 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 2242 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 2243 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. 2244 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 2245 Coupler 2246 110 mm 2247 Single tee with door 2248 110x110x110 mm 2249 Bend 87.5° 2250 110 mm 2251 Shoe (Plain) 2252 110 mm Shoe 2253 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 2254 110 mm 2255 Supplying and fixingofHDPE pipe (PE grade 63 - PN-8 ) confirming to IS 14333-1996chemical waste pipes jointed with rubber ring with good quality lubricantwithfittingsinclussive of allnecessaryspecialslike bends, tees, offsets,junctions etc laid under floor/under ceiling/on walls with suitable clamps and specialscuring, necessary chasing, jointing and restoring to original conditions, testing etc. including all other incidental chargesetc.complete for successful completion of work as per specifications, and asdirected by Engineer -in- Charge. 2256 110 mm outer dia 2257 50 mm outer dia 2258 Providing & fixing in position upvc Por S trap of self cleaning design offollowingsizesfor the embedded areasMaking proper connection withchemical sealent joint , cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors wherever required. 2259 Providing & Fixingwater cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . 2260 Sub Head– II Water Supply 2261 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 2262 Internal work – Exposed on wall. 2263 20 mm nominal outer dia Pipes 2264 25 mm nominal outer dia Pipes 2265 32 mm nominal outer dia Pipes 2266 40 mm nominal outer dia Pipes 2267 50 mm nominal outer dia Pipes 2268 65 mm nominal outer dia Pipes 2269 80 mm nominal outer dia Pipes 2270 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 2271 Concealed including cutting chases and making good the wall etc. 2272 15 mm nominal outer dia Pipes 2273 20 mm nominal outer dia Pipes 2274 25 mm nominal outer dia Pipes 2275 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 2276 20 mm dia. nominal bore 2277 25 mm dia. nominal bore 2278 32 mm dia. nominal bore 2279 40 mm dia. nominal bore 2280 50 mm dia. nominal bore 2281 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 2282 25 mm nominal bore 2283 Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge 2284 Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge 2285 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 2286 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 2287 15 mm nominal bore 2288 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 2289 15 mm nominal bore 2290 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 2291 15mm nominal bore 2292 Providing and fixing uplasticised PVC connection pipe with brass unions : 2293 45 cm length 2294 15 mm nominal bore 2295 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 2296 150 mm diameter 2297 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 2298 (a) 15 mm nominal dia 2299 Providing , Fixing, testing and commissioning of CP Brass 150 mmx 150 mmShower head with wall flange with all accessories as required andmaking good the walls wherever required. ( MAKE-JAQUAR -Model No- OHS-35495 or EQUIVALENT.) 2300 Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor withstainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect. 2301 upto 50 mm dia. nominal bore 2302 ELECTRICAL WorksGUEST HOUSE 2303 SUB HEAD - I: CIRCUIT CUM POINT WIRING 2304 SWITCH CONTROL LIGHT POINTS 2305 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 2306 Group C 2307 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 2308 Group C 2309 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 2310 Group C 2311 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (withoutIndependent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. (Switch Control Secondary Points) 2312 Group C 2313 MCB CONTROL LIGHT POINTS 2314 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Switch Control Primary Points) 2315 Primary point controlled by one MCB. 2316 Same as item above but Secondary point. i.e. Points to be looped with Primary pointwith 2.5 sqmm wire and Point wiring 2317 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 2318 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2319 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 2320 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 2321 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 2322 Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. 2323 Supply and Wiringfor 250 volts singlephase and neutral 2 Nos 6 amps socket outlate with control by 1 No switched with 2.5 sq.mm PVCinsulatedcopper conductor1100 volts grade stranded flexible FRLS wires inconcealed or surface mounted 25 mm dia 2mm thickPVC conduit including providing and fixing of 6 amps 3 pin switch socket outlet of aprpoved make and design in 2 mm thick GI box with grid plate and earthingofthird pin of the socket with2.5Sq. mm PVC insulated copper conductor strandedflexibleFRLSwire.(maximum four no. of switches socket shall be connected on onecircuit) 2324 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 2325 Supplying and fixing 63 A, 415 V, TPN Industrial type socketoutlet, with 4 pole and earth, metal enclosed plug topalongwith 63 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 2326 Supplying and fixing 80 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 80 A C curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. 2327 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. 2328 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 amp modular socket outlet and 25 Amps modular SP MCB, “C” curve including connection, painting etc. as required. (ACs & Gysers) 2329 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2330 Telephone socket outlet 2331 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2332 1 or 2 Module (75mmX75mm) 2333 6 module (78mm X 205 mm X 50 mm) 2334 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2335 3 pin , 5/6 amps socket outlet 2336 5/6 amps switch 2337 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 2338 25 mm 2339 32 mm 2340 SUBHEAD -II - FITTINGS & FIXTURES 2341 Supply, Installation, Testing and Commissioning of 10 W Bulk head Light. 2342 Supply, Installation, Testing and Commissioning of 5W Mirror Light. 2343 Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. 2344 Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED 2345 Supply, Installation, Testing and Commissioning of 15WSurface mountedLED Square Downlighter. 2346 Supply, Installation, Testing and Commissioning of150 W CHANDELIER 2347 Supply, Installation, Testing and Commissioning of 12/9WRecessed mountedLED circular Downlighter. 2348 Supply, Installation, Testing and Commissioning of9W (Nominal)Wall Bracket Light 2349 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 2350 SupplyInstallation, Testing and Commissioning of 250 mm dia Domestic Exhaust Fan 2351 SUBHEAD - III - DISTRIBUTION BOARDS 2352 Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 2353 6 way (4 + 18), Double door 2354 Supplyingand fixingoffollowingwayssurface/recessmounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note :Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 2355 12 way (4 + 36), Double door 2356 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2357 Single Pole 2358 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2359 63 A 2360 Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2361 63 A 2362 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 2363 SUB HEAD-IV , LIGHTNING CONDUCTOR 2364 LIGHTNING CONDUCTOR 2365 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. 2366 Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required. 2367 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 2368 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 2369 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2370 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2371 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. 2372 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. Details of cost for one Set 2373 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. 2374 CUTTING & FILLING 2375 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2376 Ordinary rock 2377 QUANTITY OF CUTTING (A)@100% 2378 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2379 QUANTITY OF FILLING (B)@100% 2380 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 2381 QUANTITY OF FILLING (B-A) 2382 FOOTPATH 2.00 MT. WIDE 2383 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge 2384 all kinds of soil 2385 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level. 2386 1:5:10 (1 cement : 5 course bound: 10 graded stone aggregate 40mm nominal size) 2387 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 2388 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),ncluding making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 2389 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 2390 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 2391 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. 2392 Filling available excavated earth (excluding rock) in trenches, plinth, sides ofoundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2393 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 2394 Foundations, footings, bases of columns, etc. for mass concrete. 2395 BITUMINUS ROAD FOR 3.5 MTR WIDE 2396 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2397 all kinds of soil 2398 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level. 2399 1:5:10 (1 cement : 5 course bound: 10 graded stone aggregate 40mm nominal size) 2400 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. 2401 Supplying and stacking at site.90 mm to 45 mm size stone aggregate 2402 Supplying and stacking at site63 mm to 45 mm size stone aggregate 2403 Laying, spreading and compacting stone aggregate of specified sizes to WBM pecifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required densi 2404 Laying, spreading and compacting stone aggregate of specified sizes to WBM pecifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required densi 2405 Supplying and stacking at siteStone screening 13.2 mm nominal size (Type A) 2406 Supplying and stacking at siteStone screening 11.2 mm nominal size (Type B) 2407 Supplying and stacking at siteRed bajri 2408 Supplying and stacking at siteMoorum 2409 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately).With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt 2410 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),ncluding making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 2411 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 2412 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 2413 Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :On W.B.M. @ 0.75 Kg / sqm 2414 Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete 2415 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 2416 STONE STEPS -1 2417 Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.All kinds of soil 2418 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6coarse sand : 12 graded stone aggregate 20 mm nominal size) at plinth level with: Cement mortar 1:6 (1 cement : 6 coarse sand ) 2419 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2420 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). 2421 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 2422 on top 2423 Pointing on stone work with cement mortar 1:3 (1 cement : 3 finesand): 2424 Raised and cut pointing 2425 Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. 2426 all kinds soil 2427 In all kinds soil upto 1.5m to 3.0m. depth 2428 In all kinds soil upto 3.0m to 4.5m. depth 2429 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level: 2430 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2431 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2432 Cement mortar 1:6 (1 cement : 6 coarse sand) 2433 Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, intels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) 2434 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2435 Mild steel and Medium Tnsile steel bars. 2436 Centring and shuttering including struting , proping etc and removal of form for : 2437 Suspended floors, roofs, landings, balconies and access platform. 2438 Edges of slabs and breaks in floors and walls 2439 12 mm cement plaster on rough side of single or half brick wall mix 2440 1:6 (1 cement : 6 coarse sand) 2441 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. 2442 H.D. -20- Circular shape 560mm internal diameter 2443 Boring/drilling bore well of required dia for casing/ strainer pipe, bysuitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools,plants & machineries required for the job, all complete as per directionof Engineer-in-charge, upto 90 metre depth below ground level. 2444 All types of soil 2445 300 mm dia 2446 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 2447 150 mm nominal size dia 2448 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2449 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2450 Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2451 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge. 2452 DESILTING CHAMBER 2453 Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. 2454 all kinds soil 2455 In all kinds soil upto 1.5m to 3.0m. depth 2456 Providing and laying in position cement concrete of specified grade excluding the ccost of centering and shuttering -All work up to plinth level: 2457 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2458 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2459 Cement mortar 1:6 (1 cement : 6coarse sand) 2460 Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, intels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) 2461 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2462 Mild steel and Medium Tnsile steel bars. 2463 Centring and shuttering including struting , proping etc and removal of form for : 2464 Suspended floors, roofs, landings, balconies and access platform. 2465 Edges of slabs and breaks in floors and walls 2466 Under 20 cm wide 2467 12 mm cement plaster on rough side of single or half brick wall mix 2468 1:6 (1 cement : 6 coarse sand) 2469 Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: 2470 With 20x20mm square bar 2471 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. 2472 L D- 2.5 Rectangular shape 600x450mm internal dimensions . 2473 Constructing brick masonry INSPECTION chamber 60x60x60 cm with bricks of class designation 75 in cement mortar 1:6(1 cement : 6 coarse sand) including CI cover with frame LIGHT WEIGHT complete as perdesign. With FPS bricks 2474 Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 2475 upto 1.5m depth 2476 all kinds soil 2477 In all kind of soil upto 1.5m to 3.0m. depth 2478 all kinds soil 2479 In all kind of soil upto 3.0m to 4.5m. depth 2480 all kinds soil 2481 In all kind of soil upto 4.5m to 6.0m. depth 2482 all kinds soil 2483 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level: 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2484 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2485 Cement mortar 1:6 (1 cement : 6 coarse sand) 2486 Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, intels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) 2487 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2488 Mild steel and Medium Tnsile steel bars. 2489 Centring and shuttering including struting , proping etc and removal of form for : 2490 Suspended floors, roofs, landings, balconies and access platform. 2491 Edges of slabs and breaks in floors and walls 2492 Under 20 cm wide 2493 12 mm cement plaster on rough side of single or half brick wall mix 2494 1:6 (1 cement : 6 coarse sand) 2495 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. 2496 HD-20- Circular shape 560mm internal diameter 2497 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. 2498 Rockey strata including Boulders (300 mm dia 2499 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 2500 150 mm nominal size dia 2501 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2502 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2503 Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2504 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge. 2505 DESILTING CHAMBER 2506 Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 2507 upto 1.5m depth 2508 all kinds soil 2509 upto 1.5m to 3.0m. depth 2510 all kinds soil 2511 upto 3.0m to 4.5m. depth 2512 all kinds soil 2513 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level: 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2514 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2515 Cement mortar 1:6 (1 cement : 6coarse sand) 2516 Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, intels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size) 2517 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2518 Mild steel and Medium Tnsile steel bars. 2519 Centring and shuttering including struting , proping etc and removal of form for : 2520 Suspended floors, roofs, landings, balconies and access platform. 2521 Edges of slabs and breaks in floors and walls 2522 Under 20 cm wide 2523 12 mm cement plaster on rough side of single or half brick wall mix 2524 1:6 (1 cement : 6 coarse sand) 2525 Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: 2526 With 20x20mm square bar 2527 Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. 2528 LD-2.5 Rectangular shape 600x450mm internal dimensions 2529 Constructing brick masonry INSPECTION chamber 60x60x60 cm with bricks of class designation 75 in cement mortar 1:6 (1 cement : 6 coarse sand) including CI cover with frame LIGHT WEIGHT complete as perdesign. With FPS bricks 2530 WATER SUPPLY 2531 SUB HEAD (I) :- EXTERNAL WATER SUPPLY PIPES AND FITTINGS 2532 DISTRIBUTION NETWORK FOR FRESH WATER SUPPLY 2533 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 2534 External work 2535 20 mm dia nominal bore 2536 25 mm dia nominal bore 2537 32 mm dia nominal bore 2538 40 mm dia nominal bore 2539 50 mm dia nominal bore 2540 65 mm dia nominal bore 2541 80 mm dia nominal bore 2542 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 2543 20 mm diameter pipe 2544 25 mm diameter pipe 2545 32 mm diameter pipe 2546 40 mm diameter pipe 2547 50 mm diameter pipe 2548 65 mm diameter pipe 2549 80 mm diameter pipe 2550 Providing and filling sand of grading zone V or coarser grade alround the GI pipes in external work. 2551 20mm dia nominal bore 2552 25mm dia nominal bore 2553 32mm dia nominal bore 2554 40mm dia nominal bore 2555 50 mm diameter pipe 2556 65 mm diameter pipe 2557 80 mm diameter pipe 2558 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 2559 50 mm dia 2560 80 mm dia 2561 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 2562 20 mm nominal bore 2563 25 mm nominal bore 2564 32 mm nominal bore 2565 40 mm nominal bore 2566 50 mm nominal bore 2567 65 mm nominal bore 2568 80 mm nominal bore 2569 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 2570 Providing and fixing G.I. Union in GI pipe including cutting and threading the pipe and making long screws etc. complete(New work) 2571 25 mm nominal bore 2572 32 mm nominal bore 2573 40 mm nominal bore 2574 50 mm nominal bore 2575 65 mm nominal bore 2576 80 mm nominal bore 2577 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2578 LD- 2.5 2579 Rectangular shape 600*450 mm internal dimensions 2580 Constructing masonry gate valve Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 2581 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 2582 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 2583 with common burnt clay F.P.S.(non module) brick of class designation 7.5 2584 SURFACE DRAIN (250X150 MM) 2585 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. 2586 all kinds of soil 2587 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth: consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 2588 Qty. = 25% of them no 1 2589 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level 2590 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size). 2591 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 2592 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 2593 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 2594 Foundations, footings, bases of columns, etc. for mass concrete 2595 Brick work with F.P.S. bricks of class designation 75 infoundation and plinth in : 2596 Cement mortar 1:6 (1 cement : 6 coarse sand) 2597 12 mm cement plaster finished with a floating coat of neat cement of mix : 2598 1:4 (1 cement: 4 fine sand) 2599 Hume pipe 2600 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2601 All kinds of soil 2602 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm 2603 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 2604 450 mm dia. R.C.C. pipe 2605 Providingandlayingcementconcrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 gradded stoneaggregate40 mm nominal size) alround S.W. Pipesincludingbed concrete as per standard design. 2606 450 mm diameter S.W.Pipe 2607 SUB HEAD (I) :- EXTERNAL SEWERAGE SYSTEM 2608 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. anddisposing of surplus excavated soil as directed, within a lead of 50 m : 2609 All kinds of soil 2610 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia 2611 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 2612 150 mm dia. R.C.C. pipe 2613 250 mm diameter S.W. pipe 2614 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size). 2615 150 mm diameter S.W.Pipe (626.90*0.35*0.10=21.94) 2616 250 mm diameter S.W. pipe (8.90*0.45*0.10=0.40) 2617 Constructing brick masonry manholein cement mortar 1 : 4 (1 cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4gradestone aggregate 20mm nominal size); foundation concrete 1:4:8 mix(1 cement : 4 coarse sand : 8 gradedstoneaggregate40 mm nominalsize) insideplastering 12 mm thickwith cementmortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and makingchannels incementconcrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat ofneatcement completeasper standard design 2618 Inside size 90 x 80 cm & 45 cmdeep including CI cover with frame (light duty) 455 x 610mm internal dimensions, total weight of cover & frame to be not lessthan 38 kg (weight of cover 23 kg and weight of frame 15 kg) 2619 With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 2620 Extra for depth for manholes: 2621 size 90 X 80 cm 2622 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2623 Constructing Brick Masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top with FPS bricksclass designation 75in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand :6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design. 2624 0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) 2625 with common burnt clay F.P.S.(non module) brick of class designation 7.5 2626 Extra depth for circuler type manholes 0.91 m internal dia ( at bottom ) beyond 0.91m to 1.67 m . 2627 with common burnt clay F.P.S.(non module) brick of class designation 7.5 2628 Providing and fixing square mouthS. W. Gully trapclass SP-1 complete with C.I. gratingbrickmasonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 2629 180 x 150 mm. size P type 2630 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2631 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : 2632 With 20x20 mm square bar 2633 ESTIMATE OF ELECTRICAL WORKS 2634 SUBHEAD - I - MAIN BOARDS 2635 Supplying, installing, testing & commissioning of following type compartmentalised wall mounted / floor mounted cubicle board made from 2mm thick CRCA sheet dust & vermin proof duly phosphatized & powder coated inclusive of suitable size 4 strip Al. Busbar complete with interconnection providing Lugs, inter-earthing, painting etc. i/c providing & fixing below noted accessories: 2636 Receiving,unloading,storing, handling, installation, testing and commissioning of following MV Switchboards complete as required and as per site condition and dimension of all panels shall be carried out as per the attachad sld 2637 FEEDER PILLAR 2638 Design, Manufacturing, supplying, fixing in position, testing and commissioning of the following front operated front access 2mm thick CRCA steel enclosure free standing, water, dust and vermin proof outdoor type Feeder pillars with IP-55 protection hinged and lockable doors complete with interconnections copper crimping lugs, brass glands bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system . The panels fault withstanding capacity shall be of 25 MVA at 415 volts. All live accessories part shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be of colure coded with Heat shrinkable PVC insulated sleeves. 2639 FEEDER PILLAR-3 FOR VICE PRINCIPLE, BOYS DORM. & GIRLS DORM. 2640 INCOMER 2641 1 No. 200A, 415V, Ics=25kA, 4P MCCB with thermal magnetic trip unit. 2642 1 No. Digital multifunction meter(V+A+Hz) with a set of cast resin CTs 200/5A. 2643 1 Set of Phase indicating lamp with MCB 2644 BUS BARS-I : 2645 250A TPN bus bars of aluminium alloy. 2646 For emergency supply 2647 1 No. 63A, 415V, Ics=25kA, 4P MCCB with thermal magnetic trip unit. 2648 1 Set of On indicating lamp with MCB 2649 BUS BARS-II : 2650 100A TPN bus bars of aluminium alloy. 2651 OUT GOING BUS-I : 2652 3 Nos. 63A 415V, 4P MCB of 10kA . 2653 1 No. 100A 415V, 4P MCCB of 10kA . 2654 1 No. MCB Space. 2655 OUT GOING BUS-II : 2656 2 Nos. 63A 415V, 4P MCB of 10kA . 2657 1 No. 40A 415V, 4P MCB of 10kA with 40A 4P Contactor & timer switch . 2658 2 Nos. 25A 415V, 4P MCB of 10kA . 2659 1 No. MCB Space. 2660 FEEDER PILLAR-4 FOR GUEST HOUSE, TYPE-III (G+2), TYPE-II (G+2) & TYPE II (SS). 2661 INCOMER 2662 1 No. 250A, 415V, Ics=25kA, 4P MCCB with thermal magnetic trip unit. 2663 1 No. Digital multifunction meter(V+A+Hz) with a set of cast resin CTs 250/5A. 2664 1 Set of Phase indicating lamp with MCB 2665 BUS BARS-I : 2666 300A TPN bus bars of aluminium alloy. 2667 For emergency supply 2668 1 No. 63A, 415V, Ics=25kA, 4P MCCB with thermal magnetic trip unit. 2669 1 Set of On indicating lamp with MCB 2670 BUS BARS-II : 2671 100A TPN bus bars of aluminium alloy. 2672 OUT GOING BUS-I : 2673 8 Nos. 63A 415V, 4P MCCB of 15kA . 2674 1 No. 100A 415V, 4P MCCB of 15kA . 2675 1 No. MCB Space. 2676 OUT GOING BUS-II : 2677 2 Nos. 63A 415V, 4P MCB of 10kA . 2678 1 No. 40A 415V, 4P MCB of 10kA with 40A 4P Contactor & timer switch . 2679 2 Nos. 25A 415V, 4P MCB of 10kA . 2680 1 No. MCB Space. 2681 METER BOARDS 2682 Supply, installation, testing and commissioning of M.V. cubical type totally enclosed dust, dump and vermin proof Meter Bords complete with bus bars, MV danger notice plate, on surface ISI marked Electronic kWh meter, indication lamps, CTs, Interconnection with suitable capacity aluminium strips / rods, door covers, seperate compartment for each meter, glass inspection window, connection of incoming and outgoing cables with thimbles, powder coated having following incoming and outgoingMCBs MCCBs and kWh meters complete as required. 2683 METER BOARDS - 0.375 BOYS DORMITORY & 0.375 GIRLS DORMITORY 2684 1 No. 63A, 415V, Ics= 16kA, 4P MCCB with O/C, S/C protection & on indication lamp. 2685 BUS BARS: 2686 100A TPN bus bars of aluminium alloy. 2687 OUT GOING: 2688 2 Nos. 40A DP MCB of 10kA with space for electronic direct kWh energy meter complete with all necessary wiring as per the Meter vendor requirement. 2689 7 Nos. 40A DP MCB of 10kA. 2690 METER BOARDS - VICE PRINCIPAL 2691 1 No. 63A, 415V, Ics= 16kA, 4P MCCB with O/C, S/C protection & on indication lamp. 2692 BUS BARS: 2693 100A TPN bus bars of aluminium alloy. 2694 OUT GOING: 2695 1 Nos. 40A DP MCB of 10kA with space for electronic direct kWh energy meter complete with all necessary wiring as per the Meter vendor requirement. 2696 1 No. 40A DP MCB of 10kA. 2697 METER BOARDS - GUEST HOUSE & TYPE - (SINGLE STOREY) 2698 1 No. 63A, 415V, Ics= 16kA, 4P MCCB with O/C, S/C protection & on indication lamp. 2699 BUS BARS: 2700 100A TPN bus bars of aluminium alloy. 2701 OUT GOING: 2702 2 Nos. 40A TPN MCB of 10kA with space for electronic direct kWh energy meter complete with all necessary wiring as per the Meter vendor requirement. 2703 1 No. 40A DP MCB of 10kA. 2704 METER BOARDS - TYPE-III RESIDENCE (G+2) 2705 1 No. 63A, 415V, Ics= 16kA, 4P MCCB with O/C, S/C protection & on indication lamp. 2706 BUS BARS: 2707 100A TPN bus bars of aluminium alloy. 2708 OUT GOING: 2709 4 Nos. 40A TPN MCB of 10kA with space for electronic direct kWh energy meter complete with all necessary wiring as per the Meter vendor requirement. 2710 1 No. 40A DP MCB of 10kA. 2711 METER BOARDS -TYPE-II RESIDENCE (G+2) 2712 1 Nos. 100A, 415V, Ics= 16kA, 4P MCCB with O/C, S/C protection & on indication lamp. 2713 BUS BARS: 2714 125A TPN bus bars of aluminium alloy. 2715 OUT GOING: 2716 2 Nos. 40A DP MCB of 10kA with space for electronic direct kWh energy meter complete with all necessary wiring as per the Meter vendor requirement. 2717 7 Nos. 40A DP MCB of 10kA. 2718 SUBHEAD - II - EARTHING 2719 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 2720 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. 2721 Earthing with Cu. earth Plate 600mm x 600mm x 3mm thick includingaccesssories, and providingmasonary enclosurewith cover plate (CI heavy duty) having locking arrangement and watering pipe pipe of 2.7 mtr long etc. with charcoal or coke and salt) as required. 2722 Supplying and laying 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required. 2723 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. 2 nos used for 50 x 5 for the Neutral earthing of euipments ) 2724 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 2725 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required. 2726 Supply and laying medium class GI pipe under road/paved areas/wall crossing etc. including earth excavations refilling, ramming and making good as approved. 2727 150 mm dia GI pipe Class B 2728 SUBHEAD - III - SUPPLYING & LAYING OF CABLE 2729 L.T. CABLES 2730 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 2731 63 mm dia (OD-63 mm & ID-51 mm nominal) 2732 90 mm dia (OD-90 mm & ID-76 mm nominal) 2733 120 mm dia (OD-120 mm & ID-103 mm nominal) 2734 160 mm dia (OD-160 mm & ID-135 mm nominal) 2735 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 2736 90 mm dia (OD-90 mm & ID-76 mm nominal) 2737 120 mm dia (OD-120 mm & ID-103 mm nominal) 2738 160 mm dia (OD-160 mm & ID-135 mm nominal) 2739 Laying of one number PVC insulated & PVC sheathed/ XLPE Power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. 2740 Upto 35 sq.mm 2741 Above 35 sq. mm and upto 95 sq. mm 2742 Above 95 sq.mm and upto 185 sq.mm 2743 Above 185 sq.mm and upto 400 sq.mm 2744 Supply of following sizes of XLPE insulatedAluminum conductor strip/ wire Armoured, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS-7098 Code and technical specifications. 2745 6 sq. mm 4 core 2746 4 X 16 sq. mm (28mm 2747 3½ X 25 sq. mm (28mm) 2748 3½ X 35 sq. mm (32mm) 2749 3½ X 50 sq. mm (35mm) 2750 3½ X 150 sq. mm (50mm) 2751 3½ X 185 sq. mm (57mm) 2752 3½ X 240 sq. mm (62mm) 2753 3½ X 300 sq. mm (70mm) 2754 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required. 2755 4 X 6 sq. mm (28mm 2756 4 X 16 sq. mm (28mm 2757 3½ X 25 sq. mm (28mm) 2758 3½ X 35 sq. mm (32mm) 2759 3½ X 50 sq. mm (35mm) 2760 3½ X 150 sq. mm (50mm) 2761 3½ X 185 sq. mm (57mm) 2762 3½ X 240 sq. mm (62mm) 2763 3½ X 300 sq. mm (70mm) 2764 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 2765 150 mm dia 2766 250 mm dia 2767 Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays with perforation not morethan 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts& nuts, painting suspenders etc as required. 2768 150 mm width X 50 mm depth X 1.6 mm thickness 2769 300 mm width X 50 mm depth X 1.6 mm thickness 2770 450 mm width X 50 mm depth X 2 mm thickness 2771 Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays bends with perforationnot more than 17.5%,, joined with connectors, suspended fromthe ceiling with M.S. suspenders including bolts & nuts, paintingsuspenders etc as required. 2772 150 mm width X 50 mm depth X 1.6 mm thickness 2773 300 mm width X 50 mm depth X 1.6 mm thickness 2774 450 mm width X 50 mm depth X 2 mm thickness 2775 Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays Tee with perforation notmore than 17.5%, joined with connectors, suspended from theceiling with M.S. suspenders including bolts & nuts, paintingsuspenders etc as required. 2776 150 mm width X 50 mm depth X 1.6 mm thickness 2777 300 mm width X 50 mm depth X 1.6 mm thickness 2778 450 mm width X 50 mm depth X 2 mm thickness 2779 Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays Cross Member withperforation not more than 17.5%, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts& nuts, painting suspenders etc as required. 2780 150 mm width X 50 mm depth X 1.6 mm thickness 2781 300 mm width X 50 mm depth X 1.6 mm thickness 2782 450 mm width X 50 mm depth X 2 mm thickness 2783 SUB HEAD -IV :EXTERNAL LIGHT 2784 Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. 2785 Above 6.5 metre and upto 8.0 metre 2786 Supplying, installation, testing and commissioning of 60W LED Street LightIP66 LED with High performance having system lumen output of minimum 9900 lumens, contemporary designed housing made of die-cast aluminium, with street optic LENS for uniform light distribution. PF better than 0.9, CRI better than 70 complete with all accessories. Wipro Cat No.: LR 02-102-XXX-57-G2 Street light 2787 Supplying, installation, testing and commissioning of 60W LEDSolar Street Light On 6 Meter GI octagonal Pole having Compact, Aesthetic, Eco friendly & modern integrated Solar street light in extruted Aluminum construction with high efficiency monocrystalline silicon photo voltaic panel, high efficacy SMD LED 6500K having secondary lens optics for street lighting distribution, high performance lithium battery, MPPT charge controller & Intelligent control module/sensor with higher reliability, long service life, suitable for easy & quick installation. Wipro Cat No.:LR 14-591-XXX-65-XX. 2788 Supply, testing & commissioning of 6.0 meter high G.Ioctagonal pole (Above Ground Level) with single/double arm as per requirement of suitable length with inbuilt junction box with 10A SP MCB, connectors for incoming/outgoing cable connection and 300mm x 300mm x 20 mm thick base plate and bracket (double arm/single arm whichever required) complete in all respect. 2789 Providing, installation of 200 x 150 x 125 mm polycarbonate weather proof (IP-55) junction box and SP MCB’s and terminal block. Supplying and laying cable through GI pipe upto junction box including excavation and back filling, wiring with 2 x 2.5 sq.mm PVC insulated 1100 volts grade copper conductor wires from junction box to lighting fixturecomplete. 2790 Supplying and laying cable through GI pipe upto junction box including excavation and back filling, wiring with 2 x 2.5 sq.mm PVC insulated 1100 volts grade copper conductor wires from junction box to lighting fixturecomplete. 2791 Supplying and fixing of high voltage insulation mat of class B having 11 KV dielectric strength, 1000mm width and thickness of 2.5mm ISI approved as required including cutting to required lengths. 2792 Supplying and fixing of high voltage insulation mat of class B having 1.1 KV dielectric strength, 1000mm width and thickness of 2.0 mm ISI approved as required including cutting to required lengths. 2793 Supplying of 11 KV hand gloves as required. 2794 Supplying of resuciation kit coomplete with instruction manual etc. as required. 2795 Supplying of fire bucket painted red with stand and approved quality conforming to IS:254/1974 2796 Supplying and Fixing of Powder Fire Extinguisher (Stored Pressure type)Capacity 06 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked ABC powder complete with squeeze grip release valve, discharge pipe, locking arrangement, pressure gauge & suitable M.S. bracket as required. 2797 Supplying of first aid box as approved complete with standard kit as prescribed by Indian Red Cross. 2798 Supplying and fixing of shock treatment chart written in English and Local language duly framed in glass as required.

INR 17700 /-

INR 1787000.0 /-

INR 8.93 Crore /-