|
| 1 | Dismantling floor,hearth or wall tiling including cement mortar bedding(but not backing) removing serviceable tiles to store and rubbish off the premises |
| 2 | Demolition of cement concrete (unreinforced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed. |
| 3 | M&L for Non-skid coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile and laid over screed bed or bedding layer 15 mm thick in CM (1:4) laid over & including 25 mm thick PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate complete all as specified & directed. |
| 4 | M&L for glazed ceramic coloured tiles, size 300 mm X 200 mm X 7 mm thick on vertical surfaces of wall such as dados, skirting etc set& jointed in neat slurry and pointed in white or colour cement to match over 10 mm thick cement plaster in CM 1:4 complete all as specified and directed |
| 5 | M & L for cement concrete type D-2, 1:4:8 using 40mm graded stone aggregate as in foundations,filling and mass concrete. |
| 6 | M & L for PCC 25mm thick type B-0, 1:2:4 nominal mix using 20mm graded stone aggregate as in sub base surfaces finished even and rough to receive the topping layer, complete all as specified. |
| 7 | M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate 75mm thick as in plinth protection finished fair and even and laid in alternatebays n.exc 2m in length all as specified and directed. |
| 8 | Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 9 | M&L for rendering 15 mm thick plaster in CM 1:4 on stone masonry surfaces or other than fair faces of brick work all as specified & directed. |
| 10 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified. |
| 11 | M&L for rendering 5 mm thick plaster in CM 1:3 on fair faces of brick work or concretesurfaces all as specified & directed. |
| 12 | Material and labour for plastering 10 mm thick in CM 1:3 on ceilingand concrete surface etc including fair finishing to top surface complete all as specified and directed by Engineer-in-charge. |
| 13 | M & L for preparation of new plastered surfaces of walls & applying three coats of white wash complete as specified and directed |
| 14 | M & L for preparation of new plastered surfaces of ceiling, chajja, facia & applying three coats of white wash complete as specified and directed |
| 15 | Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spot, moulds, moss and efflorescent salts, trading oil, greasy spots etc and applying one coat of white wash on walls after filling any hole with putty complete all as specified. |
| 16 | All as per ser item No 15 here in before but applying one coat of one bound distemper on ceiling. |
| 17 | Preparing new plastered surfaces of wall and applying two coats of oil bound distemper over 1 to 2mm thick wall care putty on walls etc all as specified . |
| 18 | Preparation of old plastered or unplastered surfaces of walls and applying 1 to 2mm thick wall care putty and applying two coats of oil emulsion distemper (of approved shade) over upto three storey complete all as specified and directed. |
| 19 | Preparation of old plastered or unplastered surfaces of walls and applying one coat of oil emulsion distemper (of approved shade) upto three storey complete all as specified and directed. |
| 20 | Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed. |
| 21 | All as per srl item No. 20 above but 20 mm bore |
| 22 | S & F water tubing 15 mm bore, medium weight, ISImarked galvanized with all fittings and fixed to walls,ceiling or laid in floors complete all as specified anddirected. |
| 23 | All as per srl item No. 22 above but 20 mm bore |
| 24 | M & L for fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleaning, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc. |
| 25 | All as per srl item No. 24 above but 20 mm bore |
| 26 | Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580X440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inletincluding connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing complete . |
| 27 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid,bedded and pointed in any mortar. |
| 28 | M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) includingpointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with providing 15mm thick screed bed in cement mortar 1:4. |
| 29 | Supply and fixing vitreous china wash hand basin, white/light coloured of size 550 x 400 mm flat back including waste pipe, CP coupling complete all as specified and directed |
| 30 | Supply and fixing stainless steel round wash hand basin, 445mm dia including waste pipe, CP coupling complete all as specified and directed |
| 31 | Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) |
| 32 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 33 | S&F stainless steel urinal Oval shape, mirror finish (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 34 | S&F Vitreous china urinal partition white of size 310x700 mm. |
| 35 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), with seat cover fixed in repair. |
| 36 | S&F 10 Ltr PVC valve less symphonic action type flushing cistern low level white/coloured with inlet ball valve float , handle, PVC pipe toWC andincl PVC connection 600mm long complete fixed in repairs. |
| 37 | S&F vitreous china squatting pan Orrisa pattern 580x440mm white with integral foot rest (excluding flushing cistern) fixed in repairs |
| 38 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 39 | Supply and fixing 15 mm bore pillar tap standard of PTMT any colour, high pressure for iron pipe or for brass ferrule (minimum weight 110 gms) complete all as specified and directed |
| 40 | Taking down AC pipe of any type laid in trenches, floor or fixed on wall etcincluding accessories complete all as specified and directed. |
| 41 | S & F 75mm bore cast iron spun pipe, soil, waste and vent pipes in any length with or without ears including jointing with cement joints, laid in trenches or in floor, complete all as specified and as directed. |
| 42 | S & F 100mm bore cast iron spun pipe, soil, waste and vent pipes in any length with or without ears including jointing with cement joints, laid in trenches or in floor, complete all as specified and as directed. |
| 43 | S & F 75mm bore cast iron spun pipe, soil, waste and vent pipes in any length with or without ears including jointing with cement joints, fixed to walls, complete all as specified and as directed. |
| 44 | S&F CI vent cowl bore 75 mm bore. |
| 45 | S&F cast iron 75 mm bore bends (any radius) fixedwith cement joint. |
| 46 | S&F cast iron 100 mm bore bends (any radius) fixedwith cement joint. |
| 47 | S&F 110 x 75mm bore cast iron reducer fixed to walls with cement joint complete all as specified and directed. |
| 48 | S&F cast iron 100 mm bore branch piece single (Tee) fixed to walls with cement joint with or without oval access door complete all as specified and directed. |
| 49 | S&F in repairs square grating 150 mm size of PTMT (minimum weight 100 gms) complete all as specified and directed |
| 50 | S & F in repairs 15 mm Fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed |
| 51 | S & F in repair swivel shower of PTMT, any colour for fixing with 15mm pipe (minimum weight 40 gms) complete all as specified anddirected. |
| 52 | S&F in repairs Fancy stop cock 15 mm dia cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as spd & directed |
| 53 | S&F in repairs PVC connection, heavy duty 15mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed |
| 54 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) |
| 55 | Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site all as specified and directed |
| 56 | M & L for rolled mild steel work angle ironas in door frame (Chowkhats) including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed |
| 57 | S & F hold fast of flat iron 25 x 6 mm conforming to Fe-290 or Fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed |
| 58 | S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail.MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed. |
| 59 | S&F Steel door including projecting type hinges, steel handle, complete,with glazing bars, dovetailed or welded |
| 60 | S & F factory made steel ventilator conforming to IS 1038 with top hung shutters including Box type hinges with steel peg stay complete,dovetailed, welded incl fixing of lugs in PCC 1:2:4, typeB-1 & making good walls & cills to match the existing surface complete all as specified & directed |
| 61 | M&L for MS framed work such as 12mm squareguard barsconforming to Fe 290-0 or Fe 330-0 welded to ventilator/window complete all as specified and directed |
| 62 | S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed. |
| 63 | S&F aluminium, anodised, barrel tower bolts of extruded section, ISI marked, 150 mm long complete all as specified and directed. |
| 64 | S & F aluminium handle fabricatedtype, anodised 150mm size conforming to IS complete all as specified and directed. |
| 65 | Hacking out old, broken glass (any thickness, size, quality or description) from steel or wooden frame n exc 0.50 Sqm each pane complete all as specified and directed. |
| 66 | S & F figured glass pin headed type, 4 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane for steelor wooden windows/doors fixed with wooden bead and pin tacked complete all as specified and directed. |
| 67 | M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed. |
| 68 | M&L for preparation of old steel surface over 10cm width or grith & applying one coat of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed. |
| 69 | Dismantling of existing unserviceable water tank ofany description capacity exc 500 Ltrbut n. exc 1000 Ltrs capacityeach complete all as specified and directed |
| 70 | S& F rotational moulded synthetic (HDPE) water storage tank, three layered, white in colour, 1000 litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed. |
| 71 | S&F ballvalves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore complete (minimum weight 210 gm). |
| 72 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc in soft loose soil and getting out loose/soft soil. |
| 73 | Returning, filling in includingspreading, levelling, watering & well ramming in layers n exc 25cm thick complete all as specified and directed |
| 74 | Demolition and breaking up 150mm dia in bore drain pipes (salt glazed ware, AC or Reinforced concrete) set in cement mortar |
| 75 | M&L for 150mm dia in bore SGSW drain pipes laid in trenches and jointed complete all as specified. |
| 76 | M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe they are laid with PCC 1:4:8 type D-2for pipe of 150mm dia in bore. |
| 77 | M&L for PCC 1:4:8, type D-2, using 40mm graded crushed stoneaggregateas in hauncing to side of SWSG pipe 150mm dia in bore complete all as specified and directed. |
| 78 | Cutting into existing manholes for removing existing branch drain, making good to pipe and rendering cutting out branch channel, and making good benchings |
| 79 | M & L for PCC 1:3:6 type C-1, using 20mm graded crushedstone aggregateas incoping, bed blocks, holdfastetc all as directed |
| 80 | Removing oldtarfelt or polythene film including taking down plaster of sunken floor , roughening and cleaning by brushing with wire brush to remove all dirt and apply a coat of cement slurry with 3.00 Kg of cement per sqm and Rendering 15mm thick in CM 1:3 using WPC finished rough(sunken floor/wall) and then applying two course treatment as follow :-(i) Applying bitumen primer @ 0.40Kg/Sqm(ii) Laying APP (Atactic polypropylene) modified membrance 3mm thick and weighting not less than 3 Kg/Sqm with 100 GSM/Sqm non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap.The membrane has to be laid with LPG torch and over lap sealed and finished neat. |
| 81 | Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets,light fittings etc.and keeping in safe custody for takingcredit complete all as specified and as directed by Engineer-in-Charge |
| 82 | Taking down ceiling fan/exhaust fan any sweep, removing blades ,cleaning the fan completely for dust and dirt as well as oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engineer-In-Charge. |
| 83 | M&L for point wiring withPVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI markednot less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with3 mm thick bakalite laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductordrawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following :- |
| 84 | (a) One light point controlled by one switch 5 Amp. |
| 85 | (b) One ceiling fan/exhaust fan point controlled by one switch 5Amp |
| 86 | All as per item No 83 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independent board. |
| 87 | S&F Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm including cutting of hole of required size. |
| 88 | S & F Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified. |
| 89 | S & F Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified |
| 90 | S & F Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified. |
| 91 | S & F of ceiling rose, 3 terminal, PVC/polycarbonate isolated body complete all as specified and directed. |
| 92 | S & F Modular white cover plate including Modular baseframe/boxes& powder coated Modularsheet metal concealed box for 12 module complete all as specified. |
| 93 | All as per Item No-92 above but 3 module complete all as specified. |
| 94 | Supply and fixing LED light fitting 1 x 18W, 220V, AC including LED tube light and connecting up with three flexible copper conductor cable of suitabe size from ceiling rose complete all as specified and directed by Engineer in charge. |
| 95 | S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 96 | S&F LED bulb 7 watt complete all as specified and directed. |
| 97 | S&F sheet metal enclosuredistribution board SPN 4 way230 V, 50 Hz double doorwith neutral, Earthing bar and din rail complete. |
| 98 | S&F MCB SPN 40A to 63A, 10 KA, 230/240 volts \"C\" series complete |
| 99 | S&F MCB single pole 6A to 32 A, 10 KA, 230/240 volts \"C\" series complete |
| 100 | M&L in replacement of sub main wiring with two single core FRLSPVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sq mm drawing through and includingconcealed rigid non metallic PVC conduit medium grade ISI marked minimum 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sq mmas earth continuity conductorconnected to commen earth and earth dolly complete including taking down existing UNSV. |
| 101 | M&L for earthing complete for bldgwith galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm diaby means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel,PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish ,internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge,80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled withcharcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified includingprovision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete ,all excavation andearth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete. |
| 102 | Note:- Schedule of credit of Rs. 1,34,443.00will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents. |
