|
| 1 | Dismantling of old rested plain or corrugated steel sheeting, any gauge, thickness,including Nainital or similar pattern roof covering etc. complete all as specified and as directed. |
| 2 | S&F pre-painted galvalume aluminum zinc coating GIbased corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE) |
| 3 | M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with selftapping screws as specified. (Colour as approved by GE) |
| 4 | Dismantling timber scantlings 40Sq.cm and over in section, in any position complete all as specified and directed. |
| 5 | S&F mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 6 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 7 | Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromeprimer, complete all as specified and directed. |
| 8 | Dismantlingwall and ceiling boards (fibre, pulp, insulation,etc) or insulation boards,any thickness,including cover fillets, complete all as specified and directed. |
| 9 | S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed. |
| 10 | M&L 6mm thick E-board (classic) false ceiling of size 600x600mm fixed to snap grid false ceiling complete all as specified and directed. |
| 11 | Demolition ofbrickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed. |
| 12 | M&L brick work with sub class \"B\" bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6 complete all as specified and directed. |
| 13 | M&Lwalling of random rubble, stone masonry un-coursed, brought upto course with best quality locally available harder stones such as granite, trap, basalt stone etc well bonded, bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. |
| 14 | Demolition of cement concreteunreinforced in ground floors, kota stone, granite flooring, tiles flooring andpaving\"snot exceeding15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed. |
| 15 | M&L PCC M-10 (nominal mix) type C-1(using 20mm crushed stone aggregate) as in surface channels or drains etc complete all as specified and directed. |
| 16 | M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.(inner girth only measured) |
| 17 | M&L 50mm thick PCC M-10 type C-2 (using 20mm thick crushed stone aggregate) as in plinth protection/foot path finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 18 | Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed. |
| 19 | M&L rendering 15mm thickplaster in cement mortar(1:4) on fair faces of brick work/stone masonary, finished even and smooth without using extra cement complete all as specified and directed. |
| 20 | M&L rendering 15mm thickplaster in cement mortar(1:6) on fair faces of brick work/stone masonary, finished even and smooth without using extra cement complete all as specified and directed. |
| 21 | M&L two coats of distempering walls with distemper oil emulsion over a coat of chalk whiting with 2 to 3mm thick wall careputty on newly plastered wall surface including preparation of surfaces complete all as specified and directed. |
| 22 | M&L preparation of old plastered or unplastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty 2 to 3mm complete all as specified and directed. |
| 23 | M&L preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed. |
| 24 | M&L preparation of old plastered or unplastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed. |
| 25 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.50 sqm each complete all as specified and directed. |
| 26 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm but n.exc. 4 sqm each complete all as specified and directed. |
| 27 | Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed. |
| 28 | Refixing shutters in the same opening and of any discription exc 1sqm but n. exc 2 sqm each. |
| 29 | S&F factory made Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.and providing one shop coat of primer and taring back side of frame complete all as specified and directed. |
| 30 | S&F rolled mild steel bands,straps,supports or stays for rainwater,ventilating pipes,including bolts,if required; hooks(stays),heavy,for large gates,hook and pintle hinges;large hasps and staples;chains;hand made sliding bolts;clamps;hold fasts;wall ties;hooks for hanging fans;plain angle cleats for securing purlines to wooder trusses conform to Fe-290 Gde E-165 complete all as specified & directed. |
| 31 | M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed. |
| 32 | S&F 35mm thick factory made 2nd class hard wood rail and styleplain framed, panelled shutter with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board withcommercial veneering on both faces. The size of rail and style as per IS:1003 (part 1) kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 33 | S&F 35mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed. |
| 34 | S&F stainless steel wire cloth 1.23mm nominal dia of wire fixed with tinned tacks of stainless steel staples, complete all as specified and directed. |
| 35 | M&Lpreparation of old wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 36 | M&Lpreparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 37 | S&F 3mm thick sheet glass, ordinary quality, plain/figured in square n exc. 0.5 sq.m in each pane complete all as specified and as directed. |
| 38 | S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay doytailed at welded incl 2 Nos tower bolts 150 mm long for each leaf and 8 mm square bar grills at spacing as shown on drg welded to FI frame work,incl other fittings,hinges,handles tarred hold fast PCC blocks etc. all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 ,complete all as specified. |
| 39 | S&F 100 mm sizebutt hinges, medium weight, cold rolled mild steelcomplete all as specified and directed. |
| 40 | S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded sectioncomplete all as specified and directed. |
| 41 | S&F aluminium handles, cast type, anodised of size 150 mm long,complete all as specified and directed. |
| 42 | S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 43 | S&F in repairs 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 44 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 45 | M&Ljoint free(edge cut) coloured/white (as per site requirement) glazed ceramic tiles in vertical surfaces350x450x7mm,450 x 300x 7mm/ 600 x 300 x 7mm as in skirting/dado etc, over and including 10mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and directed. |
| 46 | M&LNon-skid joint fee (edge cut), coloured/digital ceramic tiles 7 to 8mm thick (Square/rectangular)area of each tile 300 x 300mm/400x400mm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed. |
| 47 | M&LNon-skid joint free (edge cut), coloured/digital ceramic tiles 7 to 8mm thick (Square/rectangular)polished area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed. |
| 48 | M&L 25 mm thick PCC 1:2:4 type B-1 (20mm graded stone aggregate) as in leveling course offlooring & roof etc, complete all as specified and directed. |
| 49 | S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed. |
| 50 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails.M.S. frame shall be covered with heat molded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed. |
| 51 | Dismantling 75/100mm dia cast/PVC drain pipes, jointed in cement mortar fixed in trenches and taking out of trenches removing where directred complete all as specified and directed. |
| 52 | S&F 75mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall/laid in trenches or in floors etc.complete all as specified and directed. |
| 53 | S&F 110mm bore of pipe PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall/laid in trenches or in floors etc.complete all as specified and directed. |
| 54 | S&F 75mm bore PVC (SWR) bends complete all as specified and directed. |
| 55 | S&F 75mm bore PVC (SWR) junction,(single T) equal or unequal with oval access door ,complete all as specified and directed. |
| 56 | S&F 100/110mm bore PVC (SWR) bends complete all as specified and directed. |
| 57 | S&F 110mm bore PVC (SWR) junction,(double T) equal or unequal with oval access door ,complete all as specified and directed. |
| 58 | S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed. |
| 59 | S&F 100 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 60 | S&F PVC (SWR) vent cowl 100/100 bore dia, complete all as specified and directed. |
| 61 | S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GInipple for inlet, outlet, washout and overflow etc,including 25mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed. |
| 62 | S&F vitreous china squatting pan water closet, orissa pattern, size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVC (SWR) \"S\" trap,setting trap and pan in lime concrete and jointing to flush pipe (fixed in repair) and making good disturbed surfaces of floor and match with existing follor, complete all as specified and directed. |
| 63 | S&F vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, \"P\" or \"S\" trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device(excluding flushing cistern and flush pipe), complete all as specified and directed. |
| 64 | S&F vitreous china urinals, half staff type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal including water spider to plugs with and including 60m long brass screws, pointing around urinal back in cement, fixintg automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed. |
| 65 | S&F 10 litres capacity PVC valve less symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle including brackets & 32 mm size PVC flush pipe, complete all as specified and directed. |
| 66 | S&F PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and directed. |
| 67 | S&F Vitreous china, wash hand basin, (white) of size 550mm x 400mm including brass CP waste coupling 32mm size with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed. |
| 68 | S&F in repairs aluminium anodised tubular towel rail, 20mm dia, Dtype 60cm long , fixed to wall with CP brass screw and PVC rawl plugs, complete all as specified and directed. |
| 69 | S&F 600mm x 450mm bevellededge mirror of selected quality glass, mounted on 6mm thick AC plain building board or commercial ply wood and fixed to wooden plug with chromium plated brass screw and cup washers complete all as specified and directed. |
| 70 | S&F in repairs fancy type, chromium plated, bib tap,cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed. |
| 71 | S&F in repairs pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed. |
| 72 | S&F in repairs 15mm bore fancy type stop valves/angle cock (two way if required), cast copper alloy,screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or unioncomplete all as specified and directed. |
| 73 | S&F in repairs 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for GI tubing complete all as specified and directed. |
| 74 | S&F swivel shower of PTMT any colour for fixing with shower arms 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minium eight 40gms) complete all as specified and directed. |
| 75 | Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specifed and directed. |
| 76 | Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from sitecomplete all as specified and directed |
| 77 | Taking up or down 25mm bore steel tubing and connection, including cleaning for refixing or removal from sitecomplete all as specified and directed |
| 78 | S&F steel water tubing, 15 mm bore, galvanised , \"medium grade\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. |
| 79 | S&F steel water tubing, 20 mm bore, galvanised , \"medium grade\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. |
| 80 | S&F steel water tubing, 25 mm bore, galvanised , \"medium grade\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. |
| 81 | Cutting chase, pinning in making good to faceing where required and pointing in cement mortar 1:3 to ends or edges of landing,steps, cills, sunshades, shelves,lintels,etc and cutting chase for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc. 10cm girth complete all as specified and directed. |
| 82 | S&F in repairs PVC coated mild steel conduit pipe 25mm dia (Drapery rod) with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod complete all as specified & directed. |
| 83 | Taking down existing water proofing treatment including cement plaster and cleaning with wire brushes roughening the surface and hacking out dirt, as directed and disposal of rubbish not exc 100m distance from starting point complete all as specified and directed. |
| 84 | M&L 15mm thick (average) screed bed/plaster in cement mortar 1:4 in order to maintain proper slope and base over existing roof surface for laying of APP based polymeric membrane, mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and directed.(Note:- WPC and polymeric memebrane shall be measured and paid separately) |
| 85 | M&L applying a coat of bitumen primer conforming to IS: 3384-1986 over plastered surfaces @ 0.40 litres/Sqm of density 0.87-0.89 Kg/litres at 25º C and viscosity 70-160CPS (bitumen primer shal be of same make as of membrane) including preparation of surfaces, complete all as specified and directed. |
| 86 | M&L APP (Atactic Poly-propylene polymer) modified membranes, five layered, 3mm thick weighing not less than 3.6 Kg/Sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacturer\"s instructions by authorised applicator only after applying evenly a coat of bitumen VG-10 grade @ 1.20 Kg per sqm on the bottom of APP and on top of joints of APP complete all as specified and directed. |
| 87 | Supply only liquid water proofing compound complete all as specified and directed. |
| 88 | M&L plain cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in roof kerbs, mud stops, rounded or chamfered on edges,complete all as specified and directed. |
| 89 | Dismantling of single layer Mangalore pattern or similar tiles in roofing incl backing plaster and disposal of rubbished not exc 100m distance from starting point complete all as specified and directed. |
| 90 | M&L roof tiles, Mangalore pattern, interlocking at side joints, laid over 15 mm thick screed bed in cement mortar 1:3 andincluding taking down existing roof tiles, complete all as specified and directed |
| 91 | M&L ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and directed. |
| 92 | M&L mat finish non-skid, premium class I grade, joint free coloured ceramic tiles 7 to 8mm thick (Square/rectangular)area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed. |
| 93 | M&Lmachine cut kota stone slab flooring 18 to 20mm thick laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 15 mm thick screed in CM (1:6) complete all as specified and directed. |
| 94 | M&Lmachine cut kota stone slab 18 to 20mm thick in riser of steps,skirting,dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed. |
| 95 | M&L mirror polishing on old marble/granite/kota stone/stone work where ever required to give high gloss finish complete all as specified and directed. |
| 96 | M&L rendering 10mm thick plaster in CM 1:6 on brick or concrete surfaces or other than fair faces of brick masonry, finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 97 | M&L 10mm thick plaster in CM 1:4 on ceiling finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 98 | M&L preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over primer over wall care putty complete all as specified and directed. |
| 99 | M&L preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 100 | M&L preparation of newly plastered surface of wall and applying two coats of plastic emulsion paint (exterior) over a coat of primer complete all as specified and directed. |
| 101 | M&L for complete removal of existing treatment of walls and applying two coats of plastic emulsion paint over over primer (exterior emulsion) complete all as specified and directed. |
| 102 | M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper white or tinted, over coat of wall puttycomplete all as specified and directed. |
| 103 | M&L preparation of old steel surfaces of any description not otherwie described, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. |
| 104 | M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished and moulding of outer edges) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in CM 1:4,complete all as specified and directed. |
| 105 | SCHEDULE \"A\" PART-IITaking down crefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. |
| 106 | M&L for point wiring for one light/fan/call bell point controlled by one 5/6 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLSH, PVC insulated unsheathed heavy duty cable 1100 volts including continious earth wire of size 1.5 Sqmm copper conductor multistranded FRLSH, PVC insulated (unsheathed) drawn into concealed rigid non-metallic PVC conduit med grade ISI marked not less than 20mm wide of 1.8mm wall thickness ISI marked including modular GI sunken flosh box (modular GI flush boxes of any way i.e. 1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed for the following:-(a)Wiring shall be done by using proper colour coding.(b)Earth wire shall be of green colour.(c)On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed.Note: Quoted rates deems to be included the cost of modular plate (1 to 8 way) for mounting switches, sockets & regulators as required at site. |
| 107 | All as per the description of serial item No 106 here-in-before but one 5 pin socket outlet, 5 amps on the same board complete all as specified and directed. |
| 108 | All as per the description of serial item No 106 here-in-before but one 5 pin socket outlet, 5 amps on independent board complete all as specified and directed. |
| 109 | All as per the description of serial item No 106 here-in-before but for one 16 Amps socket point on independent board with 2.5 Sqmm PVC insulated FRLS-H multi-stranded copper conductor with 2.5 Sqmm PVC insulated FRLS-H multi-stranded copper conductor as earth wire & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed. |
| 110 | S&F modular switch 1 way 6 A,1 module complete all as specified and directed. |
| 111 | S&F modular socket, 6A-2/3 pin combined 2 module complete all as specified and directed. |
| 112 | S&F modular socket, 6A and 16A, 2/3 pin combined 2 module complete all as specified and directed. |
| 113 | S&F modular switch 1 way 16A, 1 module complete all as specified and directed. |
| 114 | S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and directed. |
| 115 | S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 116 | S&F fan regulator 120W-2 module complete all as specified and directed. |
| 117 | S&F LED bulb 9 watt complete all as specified and directed. |
| 118 | S&F LED complete fitting including batten & T-8 Retro LED polytcarbonate 1 x 20 watt tuberod, appx 4 feet long, environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete all as specified and directed.Make: Bajaj Cat Part No. for batten BLRB-DB118 and Cat Part No. for tube rod BLRB20WLED/Havells Cat Part No. for batten STREAKNEOT8UPTO1x22wSSBSWH Cat part of tube rod TITANIAEO1213T8SSTL20WLED865SPC/Polycab Cat Part No. for Battern PID0502001/Cat Part Tube rod LTU0101009P |
| 119 | S&F environmental friendly, ultra modern, energy saving, surface mounted, decorative bulk head fitting LED luminaire comprising of high brightness LEDs 10 watt, IP66 protection class complete all as specified and directed.Havells Cat Part No. RUGBYGENXFTS10WLED865SSYMBOPC/Bajaj Cat Part No. BIBWP 10W LED WH/Philips Cat No. WT202WLED 10S |
| 120 | M&Lsub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS-H, cable of 2 run 6 Sq mm for phase and neutral and one run of 6 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS-H, cable drawn through non metallic rigid PVC conduit not less than 20mm dia ISI marked including all conduit and fixing accessories complete all as specified and directed.Note:- (i) Two runs of cable for phase/neutral, one run of cable for earth and one run PVC conduit will be measured and paid as one unit length complete all as specified and directed.(ii)Wiring shall be done in proper colour coding. |
| 121 | Taking down ceiling fan/exhaust fan, any size nd sweep from its position after disconnecting electrical connection and transport it to workshop for servicing, dismantling for servicing including removal of bearing, bushes, condensor, connector, flexible cord, split pin etc if required removing old grease and refill fresh, lubricating bushes alongwith new washers, cleaning and washing fan blades, fan body etc. with soap solution after repairing re-assemble the same and transporting from workshop to any location in Alhilal Mil Station and fixing to position/location and connecting to electric system, testing etc. complete all as specified and directed by Engineer-in-Charge.Note:- (i)Replacement of parts/rewinding shall be measured and paid separately.(ii)Quoted rates is deemed to be inclusive of transporting fan from any location in Army Area to MES store & taking down unserviceable/defective parts. (iii)Item such as bearings, bushes, capacitor, shaft etc required for replacement shall be measured and paid separately as supply only. |
| 122 | S&F in replacement of capacitor 2.50 Mfd, 240V complete all as specified and directed. |
| 123 | M&L cutting and taking out old burnout winding of any sweep ceiling fan and rewinding with same gauge of copper winding wire of superior quality including insulation materials varnishing etc and testing complete all as specified and directed. |
| 124 | S&F 1200 mm sweep ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 125 | S&F 250 mm sweep exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding, 5 star rated complete all as specified and directed. |
| 126 | Taking down unserviceable sub main wiring of any type and any size from wall, ceiling etc. complete all as specified and directed. |
| 127 | Taking down main switches, distribution board, steel enclosure with MCB\"s any way and rating including wooden board or from steel boad and making good disturbed surfaces complete. |
| 128 | S&F factory made DB SPN8 way double door with 200 Amps rated bus bar concealed in wall IP 42/43 protection,240V for fixing MCB & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and directed.Note:- Distribution board and MCB\"s should be same make. |
| 129 | S&F MCB SP ‘B’ curve, 10KA, 240V,6 to 32 amps, in the MCB DB including necessary connectioncomplete all as specified and directed. |
| 130 | S&F MCB SPN ‘B’ curve, 10KA, 240V,40 to 63 amps, in the MCB DB including necessary connectioncomplete all as specified and directed. |
| 131 | M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connecting to GI earth wire of size 4mm size by means of bolts, nuts, check nuts and protected by provision of GI medium grade pipe of 15mm bore including provision of 40mm tk cover of RCC (1:2:4) reinforced with XPM (wt no less than 4Kg/sqm) and frame of angle iron 40mmx40mmx6mm with 6mm dia MS bar handle made to shape, GI light grade 20mm dia pipe for watering of suitable length placed on tp edge of earth plate, common salt and charcoal filling, with fixing arrangement, funnel, wire mesh and excavation and earthwork in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m complete all as per plate No. 3 of SSR 2009 Part-I and connecting to earth test point all as specified and directed by Engineer-in-Charge and including testing on completion. |
| 132 | Note:-(i)RCC pit cover shall be pre-cast of RCC (1:2:4) type B1, 80mm thick reinforcement with 8mm TOR steel @ 100 c/c in lieu of CI cover and the rate includes in the unit rate of item.(ii)Earth electrode shall be protected upto test point using necessary arrangement with suitable size GI pipe up to 7.50m and the rate includes in the unit rate of item.(iii)Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and the rate includese in the unit rate of item.(iv)The earth chamber shall be constructed 5m away from the edge of the bldg pit and the cost of the same is deemed to be included in the rate for this item. |
| 133 | Sand cushioning to under ground cable with a layer of sand 8 cm before laying the cable and 15cm after laying the cable (10 cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed. |
| 134 | M&L old size brick class \"B\" as in cable protection laid dry,flat,transversally along the length of cable on sand cushioning with width equal to length of the brickcomplete all as specified and as directed. |
| 135 | S&F 40mm bore galvanised iron, light grade (ISI marked) laid in trenches / fixed on wall / poles etc for protection of cable,,including taking out old tubing complete all as specified and as directed. |
| 136 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc or for laying of cables, errection of poles, struts / stays etc including taking out cable cover or stone slab, not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and directed. |
| 137 | Returning filling in including spreading leveling watering and well ramming inlayers not exceeding 25 cm in any type of soil complete all as specified and directed. |
| 138 | Removing excavated soil n exc.50m and depositing where directed at aleveln exc 1.50m above the starting point complete all as specified and directed. |
| 139 | Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated,armoured electric cable with aluminium conductor ,cross-sectional area 25 sq.mm 4 coreincluding taking out old unserviceable cable complete all as directed. |
| 140 | Taking down unserviceable shadowless light any size and capacity including its wiring etc, and removing materials to store for keeping in safe custody and deposit it to MES yard & making good distubed surface of ceiling, wall, floors etc complete all as specified and directeed. |
| 141 | S&F shadow less light fitting complete with emergency power unit & battery back up for 30 minutes (3KVA), having ceiling mounted double domo of 630mm + 630mm dia, each dome with minimum 5 LED clusters, No of LEDs- minimum 35+35 Nos, light intensity- 1,35,000Lux + 1,35,000 Lux, fully counter balanced having a minimum longitudinal travel of 1350mm and axial rotation of 360 degree. The unit to be suitable for operation on 230V, single phase 50 cycles mains supply (For major OT having lux level 1,35,000), having field 145mm-280mm & depth of 750mm complete all as specified and directed.Note: Old unsv OT light needs to be deposited to MESMake: PHILIPLED |
| 142 | S&F UPS for 1 hours minimum backup (including sufficient battery pack) single phase AC input 160 to 220V and output 230+- 1% of capacity 0.5KVA complete all as specified and directed. |
| 143 | M&L for point wiring for one shadowless point controlled by one 5/6 amp switch with 1.5 Sqmm single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 2.5 Sqmm copper conductor multistrand FRLSH, PVC insulated (unsheathed) drawn into and including concealed PVC rigid conduit medium grade ISI marked including Modular GI sheet metal flush boxes of any way (as per site requirement) and modular white cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:-(a)Wiring shall be done by using proper colour coding.(b)Earth wire shall be of green colour(c)On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed. |
| 144 | All as per the description of serial item No 142 here-in-before but one 5 pin socket outlet, 6 amps on the same board complete all as specified and directed. |
| 145 | All as per the description of serial item No 142 here-in-before but one 5 pin socket outlet, 6 amps on independent board complete all as specified and directed. |
| 146 | All as per the description of serial item No 142 here-in-before but one 5 pin socket outlet, 16 amps, independent board with cables 2.5 Sqmm size complete all as specified and directed. |
| 147 | S&F in replacement sheet metal enclosures with socket, plug top and MCBs single pole and neutral enclosures with a two pin and earth plug and socket complete with one single pole MCB 32 Amps 240 volts complete all as specified and directed. |
| 148 | S&Fangle lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittingscomplete all as specified and directed. |
| 149 | S&F 20W LED batten complete all as specified and directed. |
