Rate Contract For The Installation Of Various Types Of Traffic Signals, Road Warning Blinkers And Led Street Lights, Thiruvananthapuram-Kerala

Rate Contract For The Installation Of Various Types Of Traffic Signals, Road Warning Blinkers And Led Street Lights- 1 ITEM No.: 1. SUPPLY OF MATERIALS 1. Supply of PVC pipe a) 2 (50mm) dia 2 b) 3 (75mm) dia 3 c) 4 (100mm) dia 4 2. Supply of GI pipe (ISI) Class Ba) 1.5 (38mm) dia 5 b) 2 (50mm)dia 6 c) 3 (75mm) dia 7 d) 4 (100mm) dia 8 3. Supply of 8 SWGGI wire for overhead cabling 9 4. Supply of 14 SWGGI wire for earthing 10 5. Supply of Cable glands 20mm/25mm/30mm suitable for cable termination in Controller 11 6. Supply of HDPE pipe (As per IS:4984:1995) a) 2 (50mm)dia 12 b) 3 (75mm) dia 13 c) 4 (100mm) dia 14 ITEM No.: 2. CIVIL WORK 7. Excavation of trench and refilling the same after laying GI/PVC pipe of various diametera) Soft cutting 1 x 0.5 15 b) Semi Hard cutting 1 x 0.5 16 c) Hard cutting (carriage way/rock surface) 1 x 0.5 17 8. Excavation of trench and refilling the same (without pipe laying)a) Soft cutting 1 x 0.5 18 b) Semi Hard cutting 1 x 0.5 19 c) Hard cutting (carriage way/rock surface) 1 x 0.5 20 9. Restoration Charges including material cost for excavated portion of the carriage way with 1:2:4 PCC 21 10. Asphalting and Restoration Charges including material cost for excavated portion of the carriage way 22 11. Excavation of RCC/PCC surface including island median etc. 23 12. Trenchless horizontal drilling under the road surface including laying of HDPE pipe of diaa) 2 (50mm)dia 24 b) 3 (75mm) dia 25 c) 4 (100mm) dia 26 13. Slot cutting 40mm width 200mm depth (saw cut) on carriage way for laying of control cable where standard excavation is not permitted. This is inclusive of slot cutting, slot cleaning bedding of control cable and refilling with PCC/ hot bitumen seal 27 14. Slot cutting 4mm width 20 mm depth (saw cut) on carriage way for laying of loop cable for vehicle sensor placement or any other purpose. This is inclusive of slot cutting, slot cleaning, bedding of loop cable and refilling with hot bitumen seal /cold sealant 28 15. Laying of PVC/GI pipe of various diameters in trenches (1 x 0.5) 29 16. Construction of controller plinth size 70cm x 50cm x 75cm (single brick construction with plastering on outside surface with 1:6 cement mortar, fixing of controller mounting frame with 4 Nos. of M 10 x 120mm bolts and painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 30 17. Supply & Installation of Name Board on Plinth: Black granite of Size – 12mm thickness & Dimensions – 600mm x 450mm engraved with the matter informed and painted with golden paint 31 18. Construction of foundation and basement for battery box (8 Nos. of battery) of size 60cm x 60cm x20cm with brick in 1:6 Cement mortarincluding plastering all around top for fixing battery box and painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 32 19. Construction of foundation and basement for battery box (2 Nos. of battery) of size 30cm x30cm x20cm with brick in C:M 1:4 including plastering all around top for fixing battery box and painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 33 20. Erection and painting with two coats of Golden yellow paint/Silverof single cantilever pole over foundation specification enclosed including the base and painting two coatsgolden yellow paint with black stripes on base all complete 34 21. Erection and painting with two coats of Golden yellow/Silverpaint of single cantilever pole with 4/2 SPV Panels as per foundation specification enclosed including construction of the base and painting two coats of golden yellow paint with black stripes over a coat of cement primer on base all complete 35 22. Erection and painting with two coats of Golden yellow/Silverpaint of 6 mtr. long pole as per foundation spec including construction of the base and painting two coats of golden yellow paint with black stripesover a coat of cement primer all complete 36 23. Erection and painting with two coats of Golden yellow/Silverpaint of7/9 mtr long pole with 4/2 SPV panelsas per foundation spec including construction of the baseand painting two coats ofgolden yellow paint with black stripes over a coat of cement primer all complete 37 24. Assembly of 1Mtr long Solar panel frame to standard pole/Cantilever Pole 38 25. Assembly of 3Mtr long Solar panel frame to standard pole 39 26. Fixing of Solar panel on Panel frame (per panel) 40 27. Fixing of controller ona) Pole 41 b) Plinth 42 28. Fixing of meter box/junction box 43 29. Fixing of Digital Count Downa) On Standard Pole/Cantilever Pole bottom portion Clock 44 b) On Cantilever Pole overhang 45 30. Fixing of Vehicle Sensing Camera a) On Standard Pole/Cantilever Pole bottom portion 46 b) On Cantilever Pole overhang 47 31. Assembly of signal heads 2/3/4/5 aspects -per set 48 32. Mounting of assembled signal heads 2/3/4/5 ona) Standard Pole/CL Pole Bottom 49 b) On Overhang of Cantilever Pole 50 33. Fixing of Pole Cap on Standard Pole /Cantilever pole 51 34. Fixing of Keltron logo / Name plate onpole 52 35. Construction of Circular foundation of 2 mtrs. dia at the bottom of the pole 53 36. Construction of circular barrier platform of dia 2 mtrs and height 1 mtr. with cement concrete 1:2:4 using 20mm metal and plastering all around the surface and top including2 coat of golden yellow paint with black stripes over a coat of cement primer 54 ITEM No.: 3. ELECTRICAL WORK37. Cable laying charges a) 2/3/4 core armoured/unarmoured 55 b) 6 core armoured/unarmoured 56 c) 12/14 core armoured/unarmoured 57 38.Laying of overhead cable with 8 SWG GI wire through pipes, poles and looping etc. including handling charges complete. Running length of bunch of cable tied to 8SWG GI wire properly tied at a height of not less than 7 mtrs. from road surface 58 39. Pole wiring chargesa) On Standard Pole 59 b) On Cantilever Pole 60 40. Wiring of signal aspects and interconnecting the aspects on assemblies 61 41. Earthing as per specification (KSEB standard) a) Controller/Battery Box 62 b) Pole 63 42. Fixing of cable glands in controller and glanding of cables all inclusive 64 43. Termination and wiring of cables in controller 65 44. Wiring and inter connection of Solar panel on panel frame (per panel) 66 45. Termination of Solar panel cables in Battery Box (per panel assembly) 67 46. Wiring of battery box per batteryincluding battery handling charges and CCU wiring 68 47. Wiring of Digital Countdown clock 69 48. Wiring of Vehicle Sensing Camera 70 ITEM No.: 4. ERECTION OF POLES ON FOUNDATION (Erection of Traffic Signal poles by bolting on RCC foundation, including construction of RCC foundation with materials, tools, curing)49. Construction of RCC foundation as per specification enclosed with materials, tools, curing etc. excluding reinforcement structure and bolts 71 50. Construction of RCC foundationas per specification enclosed with materials, tools, curing etc. including reinforcement structure and bolts 72 51. Bolting of Standard pole on foundation 73 52. Bolting of Standard pole with Solar panel attachment on foundation 74 53. Bolting of Cantilever polewithout Solar Panel attachment on foundation 75 54. Bolting of Cantilever pole with solar panel attachment on foundation 76 ITEM No.: 5. SOLAR BLINKER [1 to 20 Nos.]55. Assembly and Erection of 6Mtr. standard pole with 1 Mtr. long panel frame with the following diameter:a) 2.5 (50mm) 77 b) 3 (75mm) 78 c) 4(100mm) 79 56. Assembly and Erection of 9Mtr Cantilever pole with 1 Mtr long panel frame 80 57. Fixing of SPV panel to panel frame (per panel) 81 58. Wiring and termination of cable at solar panel(per panel) 82 59. Fixing of Signal assembly on blinker Pole (per signal head) 83 60. Wiring of Signal assembly (per signal head) 84 61. Fixing of controller box on blinker Pole 85 62. Fixing of Warning Board size 2mtr long and above 86 63. Construction of Plinth for Pole 87 64. Painting with two coats of golden yellow/Silverto solar frame, pole, plinth, clamps etc. all complete 88 ITEM No.: 6. SOLAR BLINKER [above 20 Nos.] 65. Assembly and Erection of 6Mtr. standard pole with 1 Mtr. long panel frame with the following diameter:a) 2.5 (50mm ) 89 b) 3 (75mm) 90 c) 4(100mm) 91 66. Assembly and Erection of 9Mtr. Cantilever pole with 1 Mtr. long panel frame 92 67. Fixing of SPV panel to panel frame (per panel) 93 68. Wiring and termination of cable at solar panel (per panel) 94 69. Fixing of Signal assembly on blinker Pole (per signal head) 95 70. Wiring of Signal assembly (per signal head) 96 71. Fixing of controller box on blinker Pole 97 72. Fixing of Warning Board size 2mtr long and above 98 73.Construction of Plinth for Pole 99 74. Painting with two coats of golden yellow/Silverto solar frame, pole, plinth, clamps etc. all complete 100 ITEM No: 7. SOLAR STREET LIGHT (1-20 Nos.) 75. Assembly and Erection of 3 dia 6Mtr. long standard pole with 1 Mtr long panel frame 101 76. Assembly and Erection of 4 dia standard pole more than 6 mtr long with 1 Mtr long panel frame 102 77. Assembly and Erection of 8 to 10 Mtr. long Octagonal polewithsolar panel frame (single or double) on Foundation bolts including RCC foundation and bolting structure 103 78. Fixing of SPV panel on panel frame (per panel) 104 79. Wiring and termination of cable at solar panel (per panel) 105 80. Fixing of LED luminaire on bend and fixing on pole 106 81. Pole wiring charges including drawing of cable through pole 107 82. Wiring of LED Luminaire 108 83. Fixing of battery box on Pole 109 84. Construction of foundation and basement for battery box of size 30cm x30cm x20cm with brick in C:M 1:6 including plastering all around top, fixing of battery box and painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 110 85. Wiring of Battery box including CCU and battery 111 86. Construction of Plinth for Pole 112 87. Painting with two coats of paint of suitable colour onsolar frame, pole, plinth, clamps etc. all complete 113 88. Fixing and wiring of conventional powered LED luminaire on existing KSEB pole excluding KSEB supervision charges (suitable clamp will be provided by KELTRON) 114 89. Fixing and wiring ofconventional powered LED luminaire on existing KSEB pole including KSEB supervision charges (suitable clamp will be provided by KELTRON) 115 90. Transportation of Materials at site 116 ITEM No.: 8. SOLAR STREET LIGHT (above 20 Nos.) 91. Assembly and Erection of 3 dia 6 Mtr. long standard pole with 1 Mtr long panel frame 117 92. Assembly and Erection of 4 dia standard pole more than 6 mtr long with 1 Mtr. long panel frame 118 93. Assembly and Erection of 8 to 10 Mtr. long Octagonal polewithsolar panel frame (single or double) on Foundation bolts including RCC foundation and bolting structure 119 94. Fixing of SPV panel on panel frame (per panel) 120 95. Wiring and termination of cable at solar panel (per panel) 121 96. Fixing of LED luminaire on pole 122 97. Pole wiring charges including drawing of cable through pole 123 98. Wiring of LED Luminaire 124 99. Fixing of battery box on Pole 125 100. Construction of foundation and basement for battery box of size 30cmx30cmx20cm with brick in C:M 1:6 including plastering all around top, fixing of battery box and painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 126 101. Wiring of Battery box including CCU and battery 127 102. Construction of Plinth for Pole 128 103. Painting with two coats of paint of suitable colour to solar frame, pole, plinth, clamps etc. all complete 129 104. Fixing and wiring of conventional powered LED luminaire on existing KSEB pole excluding KSEB supervision charges (suitable clamp will be provided by KELTRON) 130 105. Fixing and wiring ofconventional powered LED luminaire on existing KSEB pole including KSEB supervision charges(suitable clamp will be provided by KELTRON) 131 ITEM No.: 9. MINI MAST LIGHT SYSTEMS (1-10 Nos.) 106. Assembly and Erection of 4 dia 6Mtr. long standard pole with mast assembly with: a) 3 Nos. of LED luminaires 132 b) 4 Nos. of LED luminaires 133 c) 6 Nos. of LED luminaires 134 107. Assembly and Erection of 4 dia 8Mtr. long standard pole with mast assembly with:a) 3 Nos. of LED luminaires 135 b) 4 Nos. of LED luminaires 136 c) 6 Nos. of LED luminaires 137 108. Assembly and Erection of 8 to 10 Mtr. long Octagonal pole on Foundation bolts including RCC foundation and bolting structurewith mast assembly with: a) 3 Nos. of LED luminaires 138 b) 4 Nos. of LED luminaires 139 c) 6 Nos. of LED luminaires 140 109. Fixing of LED luminaire on mast arm 141 110. Pole wiring charges including drawing of cable through pole 142 111. Wiring of LED Luminaire 143 112. Wiring & Fixing of Junction Box on Pole 144 113. Construction of foundation and basement for standard pole of size 30cmx30cmx20cm with brick in C:M 1:6 including plastering all around top, painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 145 114. Painting with two coats of paint of suitable colour onstandard pole, mast & clamps etc. all complete 146 115. Availingnew KSEB Electric Connectionat Pole Point excluding KSEB statutory payments (KSEB charges will be paid extra on producing the actual receipt from KSEB) 147 116. Earthling of Pole as per specification 148 ITEM No.: 10. MINI MAST LIGHT SYSTEMS (above 10 Nos.)117. Assembly and Erection of 4 dia 6Mtr. long standard pole with mast assembly with:a) 3 Nos. of LED luminaires 149 b) 4 Nos. of LED luminaires 150 c) 6 Nos. of LED luminaires 151 118. Assembly and Erection of 4 dia 8Mtr. long standard pole with mast assembly with:a) 3 Nos. of LED luminaires 152 b) 4 Nos. of LED luminaires 153 c) 6 Nos. of LED luminaires 154 119. Assembly and Erection of 8 to 10Mtr. long Octagonal pole on Foundation bolts including RCC foundation and bolting structure with mast assembly with:a) 3 Nos. of LED luminaires 155 b) 4 Nos. of LED luminaires 156 c) 6 Nos. of LED luminaires 157 120. Fixing of LED luminaire on mast arm 158 121. Pole wiring charges including drawing of cable through pole 159 122. Wiring of LED Luminaire 160 123. Wiring & Fixing of Junction Box on Pole 161 124. Construction of foundation and basement for standard pole of size 30cmx30cmx20cm with brick in C:M 1:6 including plastering all around top, painting two coatsgolden yellow paint with black stripes over a coat of cement primer etc. all complete 162 125. Painting with two coats of paint of suitable colour onstandard pole, mast & clamps etc. all complete 163 126. Availingnew KSEB Electric Connectionat Pole Point excluding KSEB statutory payments (KSEB charges will be paid extra on producing the actual receipt from KSEB) 164 127. Earthing of Pole as per specification 165 ITEM No.: 11. LED STREET LIGHT 128. Fixing and wiring of conventional powered LED luminaire on existing KSEB pole including KSEB supervision charges (suitable clamp will be provided by KELTRON) 166 129. Dismantling & Transportation of old Street Lights and subsequent Fixing & wiring of conventional powered LED luminaire on existing KSEB pole including KSEB charges 167 130. Transportation of Materials at site 168 ITEM No.: 12. ADDITIONAL WORK FOR REPAIR & MAINTENANCE OF TRAFFIC SIGNAL131. Labour Charge (day time) / person 169 132. Labour Charge (night time) / person 170 133. Crane Charge 171 134. Transportation of Tools (Trivandrum) 172 135. Transportation ofTools & Labour (Outside Trivandrum) 173 136. Paint for Poles and Controller (Including brush and Turpentine etc.) 174 137. Material for fixing one Standard Pole (Including auto, loading and unloading etc.) 175 138. Material for fixing one Cantilever Pole 176 139. Material for fixing Controller / Battery box 177 140. Breaker Charge

Refer document

Refer document

Refer document