Tender For Laying Of Foundation Block For Hcp Along With Allied Works At Pumping Station Kankote Under Capex Budget Pri, poonch-Jammu And Kashmir

Laying Of Foundation Block For Hcp Along With Allied Works At Pumping Station Kankote Under Capex Budget Pri , Name Of Wss , Providing Installation, Testing & Commissioning Of Hcp 2000Gph X100mh :- Installation, Testing & Commissioning Of Hcp Set By Way Of Laying Of Rcc Foundation Block For Hc Pump Set As Per Size Of Foundation Plate. Construction Of Foundation Blocks By Way Of Excavating The Trenches Of Required Size And Disposing Off The Excavated Material To A Suitable Location Outside The Premises. Providing And Fabricating A 10Mm Dia. Tor Steel Bar Mesh And Fixing The Base Frame On The Steel Mesh And Raising The Height Of Block Upto One Feet Above Ground Level And Proper Levelling/ Finishing The Alleviated Portion Of The Foundation Block. Fabrication Of 04 Nos. New Foundation Bolts For The Hcp. These Foundation Bolts Are To Be Fixed In The Base Frame And Welding/Fixing It With Tor Steel Mesh At Appropriate Places. Providing And Laying Of Plain Cement Concrete In The Ratio Of 1:4:8 By Using 40 Mm Size Aggregate For A Height Of 150 Mm With Proper Compaction. Providing And Laying Of Reinforcement Cement Concrete In The Ratio Of 1:1.5:3 For A Height Of 1 Mtr. By Using 20/10 Mm Size Aggregate. The Rcc Foundation Block Should Be Sufficiently Alleviated With Respect To Floor Level For Transfer Of Stresses And Vibration Of Booster Pump While In Operation. Providing/Fabrication/Laying Of Suction And Delivery Lines At Pumping Station. Suction And Delivery Size Of Pipe Should Be Of As Per The Design Of Pump. Fabrication Of Suction Pipe Of Size 65Mm Dia. Pipe With Welding Work In Double Layer Using Reputed Make Electrodes To Form Strong And Leak Proof Joints And Also A Sluice Valve Of Suitable Dia Should Be Fitted Between Sump Tank And The Suction Line Using Ms Flanges, Gaskets, Nuts And Bolts. Also, Delivery Lines Of All The Pump Should Be Connected To The Respective Fabrication Of Delivery Pipe Of Size 50Mm Dia. Pipe With Welding Work In Double Layer Using Reputed Make Electrodes To Form Strong And Leak Proof Joints And Also A Sluice Valves Of Suitable Dia. Should Be Fitted Between The Delivery Manifold And The Rising Mains As Per Site Requirements Using Ms Flanges, Gaskets, Nuts And Bolts. The Suction/Delivery Pipes Shall Be Properly Painted By Using Two Coats Of Anti-Rust Primer And Two Coats Of Super Enameled Black Paint With Writing On Them. P/F Of Heavy-Duty Sluice Valve 65 Mmø-01 No. At The Suction Side. P/F Reflux Valve 50 Mmø-01 No With Flanges As Per Size Of Valves At Appropriate Place Of The Delivery Line.P/F Of Heavy-Duty Sluice Valve 50 Mmø-01 No At Appropriate Place Of The Delivery Lines. The Job Includes P/F Of M.S Bends, Flanges, Nut-Bolts, Washers Etc. Both Suction & Delivery Pipes And Accessories Should Be Independently Supported Near The Pump, So That When The Flanges, Bolts Are Tightened No Strains Will Be Transmitted To The Pump Casing. Complete Welding Of Suction/Delivery Lines With Good Quality Electrodes To Make Leak Proof Joints. The Complete Job Includes Cost Of Material, Carriage/ Shifting Charges Of Material, Welding Charges, Skilled/Semi-Skilled Labour Charges And Hire Charges Of Tools/Tackles. Electrical Installation. P/F Of Lt Control Panel. The Job Involves 1. Fabrication Of Power Handling Unit (Phu) / Auto Starter With Power Contactor And Mccb As Per Following Details. S.No. Power Contractor No. 01 Power Contractor No. 02 Power Contractor No. 03 Mccb Rating 01. 50 Amp 50 Amp 50 Amp 100Amp 2. The System Should Be Provided With A Solid-State Fault Analyzer Cum Controller Or Equivalent System. 3. The Complete System Should Be Enclosed In A Floor / Wall Mounted Ms Sheet Enclosure / Box Of Suitable Gauge And Dimensions With Proper Entry And Exit Holes For Incoming And Outgoing Cables. The Enclosure Should Be Finished With Powder Coated Painting From Inside As Well As From Outer Surface Of Approved Colour. Job Also Includes Mounting Of The Panel To The Wall / Floor Of The Pump Room. Metering: The Enclosure Should Be Front Shutter Mounted With Key Locking System Having Glass Window. Digital Electronic Voltmeter & Ampere Meter (Showing All The Three Phases) Should Be Provided Along With The Required Current Transformer And Selector Switches. The Internal Control Wiring Should Be Done With Flexible Pvc Lt Cable With Proper Thimbing At Each End. Features And Specifications: 1) The System Should Trip The Motor On Power Failure And On Appearance Of An Electrical Fault Mentioned Below Which May Otherwise Damage The Motor Field Coils And Should Not Restart Automatically Until Unless The System Is Reset Manually, Thus Providing Automation To The System And Protection To The Motor. 2) The System Shall Provide Protection Against: - A. Low Voltage Below 350 V B. High Voltage Above 450 V C. Single Phasing D. Reverse Phasing E. Un Balanced Phasing F. Dry Running G. Overloading(On All The 3 Phases) Information Section: - In Addition The System Should Have The Following Visual Features For A Quickand Accurate Diagnosis Of The Appeared Fault / Status For A Speedy Rectification Of The System— 1) Separate Led Fault / Status Indicators. 2) Led Phase Indicators. 3) An Isolation By Pass System, For Fault Analysis System, With A Blinking Indicator. 4) 3 Led, Contactor ‘Coil Ok’, Indicators, One For Each Of The Contactors / Coils. Led Star & Delta Indicators To Access The Star To Delta Timing. 5) A Tamper Proof Starting System To Avoid Manipulations By The Motor Operator To Keep The System In A Permanently On Position. Complete Job Includes Cost Of Panel/ Material, Labour Charges, Transportation/ Shifting Charges Up To Site Of Work, Including Installation, Testing And Commissioning. Providing/ Fitting Of 25Mm2pvc Copper Cable (40 Mtrs Approx.) From Starter/Panel To Motor And Vice Versa. P/F Of Al. Thimbles And Copper Thimbles Duly Crimpled By Using Crimpling Tool. Labour Charges Of Skilled/ Unskilled And Carriage Charges. Conduiting All The Copper Cables By Using Good Quality Pvc Conduit Pipe And Insulating Of All Thimble’S Joints (Copper & Aluminum) With Insulation Tape. The Job Also Involves Electric Bulbs, Electric Wire, Batten, Board And Other Required Fitments. Complete Job Includes Cost Of Material, Carriage & Skilled/Semi-Skilled Labour Charges. Painting Of Panel Board And Suction And Delivery Pipeline Of Hcp Set (With Recommended Colours) With Single Coat Of Premier And Double Coat Of Superior Quality Of Paint. Testing And Commissioning Of Pumping Machinery And Allied Electro- Mechanicals Equipment’S After Checking Of Alignment, Checking Continuity Of Complete Electrical Circuit, Tightening Of Loose Connections If Any, Plugging Of Leakage Of Joints By Welding & Tightening Of Nuts & Bolts. The Complete Job Includes Cost Of Material, Labour Charges For Loading Unloading, Carriage & Fitting Charges.The Job Also Involves Any Type Of Other Electro-Mechanical Work Required For Successful Commissioning Of Pumping Machinery Skilled/ Semi Skilled Labour Charges.(Complete Job)

INR 1000 /-

INR 3580.0 /-

INR 1.79 Lakhs /-