Supply Of Materials And Erection For Construction Of 33 Kv S / S Chamanganj And Malawa And Associated 33 Kv Line Under Edc-Ii In Distt. Prayagraj In Deposit Scheme On Full Turnkey Basis-2 Terminal Gantry Structure 3 Main Bus Bar Complete With Structure 4 33 Pin Insulator With G.I. Pin 5 33 Kv Line Isolator 6 33 Kv Bus Isolator 7 Structure For Above 8 33 Kv Post Insulator 9 Structure For Above 10 Lightning Arrester 11 Structure For Above 12 33 / 11 Kv 5 Mva T / F 13 90 Lbs Rail Pieces For T / F ( 44.64Kg ) / M 14 Plinth And Foundation Of T / F ( 5 Mva ) 15 33 Kv Vcb With Single T / F Control Pannel And Ct 200 / 100 / 1A With Structure 16 Plinth And Foundation Of Vcb 17 11 Kv Switch Gear 18 11 Kv Switch Gear 600 / 300 / 5A 350 Mva I / C 19 11 Kv Switch Gear 200 / 100 / 5A 350 Mva O / G 20 11 Kv 3X185 Mm2 Xlpecable 21 11 Kv 3X120 Mm2 Xlpecable 22 11 Kv 3X185 Mm2 Xlpe Cable Jointing Kit O / D & I / D 23 M.S.Channel 125X65x4000mm For Cable Stand 24 11 Kv 3X120 Mm2 Xlpe Cable Jointing Kit O / D & I / D 25 24 Volt Battery & Battery Charger 26 Control Cables 27 Control Cable 4X2.5 Mm2 28 Control Cable 2X2.5 Mm2 29 Earthing Of Sub Station 30 Outdoor Equipment ( Including Earth Mat ) 31 Indoor Equipment ( Including Earth Mat ) 32 Barbed Wire Fencing With Gate Etc. ( Switchyard ) 33 D / P Of 11 Kv Structure On Pcc. 8.5 Mtr. For Feeder 34 Outdoor & Switchyard & Approch Road Lighting 35 63 Kva 11 / 0.4 Kv T / F 36 11 Kv Fuse Set With Fixing Clamp 37 11 Kv Tpmo Switch With Fixing Clamp 38 Cost Of Accessories For Mounting Of 63 Kva T / F 39 L.T.Pvc Cable 4X25 Mm2 40 Painting Of S / S Structure 41 Sundries Of Stores 42 Table 43 Chair 44 Fire Bucket ( 04No. ) With Stand 45 Hand Gloves 46 Nomenclature Board Of Switch Yard & Control Room 47 Rubber Matting 48 Sub-Station Name Board 49 Erection Of Work As Per Resspo Norms. 50 Errection Of Complete Terminal Gantry Already Fabricated And Provided By The Contractorin Switch Yard As Per Drawing.The Work Includes Mounting And Fitting Of 33Kv Disc Insulator, Disc Fitting, Pin, Pin Insulator, M.S.Channel And All Other Accessories Provided By The Department To Complete Terminal Gantry.Work Also Includes Construction Of Gantry Plinth Of Size 1.0X0.45X0.45 Cum With Cement, Coarse Sand And Ballast In Ratio 1:3:6 And Plastaring Of Plinth With Cement & Sand In Ratio 1:4 Including Digging Of Pits & Backfilling, All Concreting Material Like Cement, Ballast, Sand Labour & T&P Etc.Shall Be Alsoprovided By The Contractor. 51 Erection Of Complete Bus Bar Gantry Already Fabricated And Supplied By The Contractorin Switch Yard As Per Drawing.Work Also Includes Construction Of Gantry Plinth Of Size 1.0X0.45X0.45 Cum With Cement, Coarse Sand And Ballast In Ratio 1:3:6 And Plastaring Of Plinth With Cement & Sand In Ratio 1:4 Including Digging Of Pits & Backfilling, All Concreting Material Like Cement, Ballast, Sand Labour & T&P Etc.Shall Be Provided By The Contractor. 52 Erection Of Complete Structure For 33 Kv Isolator In Switch Yard As Per Respo Drawing. Work Also Includes Construction Of Gantry Plinth Of Size 1.0X0.45X0.45 Cum With Cement, Coarse Sand And Ballast In Ratio 1:3:6 And Plastaring Of Plinth With Cement & Sand In Ratio 1:4 Including Digging Of Pits & Backfilling, All Concreting Material Like Cement, Ballast, Sand Labour & T&P Etc.Shall Be Provided By The Contractor. 53 Erection Of Complete Structure For 33 Kv Lightening Arrestor In Switch Yard. As Per Respo Drawing. Work Includes Erection Of 3 Nos.33 Kv Lightening Arrestor, Its Fitting And Mounting With Care. Grouting Of Structure With L.C, Of 1:3:6 Construction Of Plinth Size 0.90X0.45X 0.45 Cum. Plastering The Plinth With Cement Mortar With Cement And Sand In Ratio 1:4. Worksincludes Cost Of Clamp Concrete Material, Labour T&P And Cement, Which Shall Be Provided By The Contractor. 54 Erection Of Complete 33 Kv Vcb With Structure In Switchyard And Grouting Of Vcb Structures. C.T. Structure By Cement, Sand, Brick Ballast Mortar In Ratio 1:3:4. Work Includes Complete Fitting Of Vcb And C.T. On Structure Carefully With Making All Connections Of Control Cable For Operating The Vcb And C.T. Only Vcb, C.T., Battery And Battery Chargar And Their Structure Shall Be Provided By The Contractor .All Other Item Like Cement, Concrete Material, T&P Shall Be Provided By The Contractor. Work Also Includes Installation And Commissioning Of Battery And Battery Charger. 55 Installation Of 33 Kv Transformer Control Pannel In The Switchgear Room And Grouting The Pannel By Rag Bolt Using Cement, Sand Mortar In Ratio 1:3. Work Includs Fitting Of All Accessories In All Respect With Complete Connection Of Control Cable With Pannel.Grouting Material Will Be Provided By The Contractor. 56 Erection Of Complete Structure For 33 Kv Post Insulators In Switch Yard. Work Includes Installation Of 3 Nos. 33 Kv Post Insulator On Each Structure Complete As Per Schedule, Grouting Of Structure With Ist Class Brick Ballast In The Ratio Of 1:3:6, Plastering In The Ratio Of 1:3 On Plinth Size 0.90X0.45X0.45 Cum. The Work Is To Be Done Strictly As Per Respo Drawing. All The Material Like Post Insulator Cap, Cement, Concrete Material Used For Above Work Will Be Provided By The Contractor. 57 Construction Of Complete T / F Plinth Size 4.46 X 3.46 X 1.0 Mtr. Above The Ground Level And 0.5 Mtr. Deep Foundation Made As Per Drawing. Top Of Plinth Is To Be L.C. Work In The Ratio Of 1:3:6 Fitted With 3 Mtr. Long, 90 Lbs, 2Nos. Rail Pieces. Cement Mortar Is To Be Used In 1:3 Ratio. Cement, Concrete Material, Bricks Used In Plinth Shall Be Supplied By The Contractor. 6” Stone Grit Is To Be Laid Before Foundation Start For Whole Plinth. Only Rail Pieces Shall Be Supplied By Contractor . Other Material Shall Be Provided By The Contractor. 58 Safe Shifting And Mounting Of 33 / 11 Kv 5 Mva T / F On The Transformer Plinth. This Work Includes Dragging Loading, Shifting, Lifting And Complete Assembling After Placing On The Plinth.All Special And Ordinary T&P Is To Be Arranged By The Contractor. Special Care Is To Be Taken To Avoid Tilting Of T / F And Loss Of Transformer Oil. Any Damage In T / F Will Be Chargeable To Contractor. 59 Laying Of Earth Mat Through Out 33 Kv Switchyard Area As Per Respo Design And Drawing Provided By The Department. The Work Includes Diggingof Trenches 0.75 Mtr Deep As Per Drawing. Boaring Of 33 Mm M.S. Round Electrodes Upto 0.5 Mtr Below Ground Level. Connecting All Electrodes With The Help Of G.I. Strips Of Size 35X6 Mm ( Approx. 600 Kg ) And 40 Mm G.I. Pipe With Proper Welding With High Quality Electrodes M.S. Rod, G..I. Strip & G.I. Pipe Shall Be Provided By The Contractor. 60 Earthing Of Each Structure Erected In The Yard With 35X6 Mm. G.I. Strip In Duplicate Fully Welded At Both Ends To Be Connected To The Earthmat, Necessary G.I. Strip Shall Be Provided By The Contractor. 61 Earthing Of 11 Kv Indoor Equipments, Switch Gears As Per Respo Drawing. With G.I. Strip Of Size 50X6 Mm, Provided By Which Will Be The Contractor. 62 Earthing Of 33 Kv C.T. Structure Complete As Per Schedule With 50X6 Mm.G.I. Strip. All Earthing Material Shall Be Provided By The Contractor. 63 Special Earthing Of Lightening Arrestor Structure With 6 Nos. Additional 40 Mm Dia 2.5 Mtr. Long G.I. Pipe Electrodes / Rod By Digging 3 Mtr. Deep Pits And Connecting It With L.A. Through G.I. Strip 35X6 Mm Welded At Both Ends. All The Material Like G.I. Pipe, G.I. Strip Shall Be Provided By The Contractor. 64 Special Earthing Of T / F Neutral By Boring 2” Dia 20 Feet Long G.I. Pipe In The Wet Earth And Connecting It With 35X6 Mm. G.I. Strip To T / F Neutral Giving Half Round Turn At The T / F. Two Separate Earthing To Be Provided To T / F Body By Connecting It With Earth Mat By Special Earthing Arrangement For Earthing Work. Material Like Strip Of Size 50X6 / 35X6 Mm And G.I. Pipe 2” Dia 2.9 Mm Thick Shall Be Provided By The Contractor Used In Above Work. 65 Laying And Stringing Of Acsr Dog Conductor For Busbar Between Busbar Gantry As Well As Terminal Gantry. Three Phase Jumpering From Bus To Bar L.A, Vcb, C.T., Post Insulator And 33 / 11 Kv T / F, Terminal Gantry, Isolator Etc. Properly With Jumpering With P.G. Clamp, T. Clamp And Post Insulator Clamp, P.G. Clamp, T.Clamp, A.C.S.R. Dog Conductorand Any Other Clamp Required For Jumpering Shall Be Provided By The Contractor. 66 Painting Of All Structure And Equipment Inside The Switch Yard With Two Coats Of Red Oxide Primer And Thereafter Two Coats Of Aluminium Paint, Giving Silver White Finish, Painting Is To Be Done After Proper Cleaning Of The Structures. Paint, Primer, Thinner Etc. Required Shall Be Provided By The Contractor Himself. 67 Providing And Erection Of Fire Stand As Per Drawing For Fire Bucket Withm.S. Angle Iron 50X50x6 Mm With Shed Of M.S. Sheet To Cover The Bucket And Stand Properly. All Matrial Required For This Work Like M.S. Angle. 5 Nos Fire Bucket Shall Be Provided By The Contractor. 68 Installation Of 11 Kv Vcb In The Switch Gear Room, By Grouting Base Channel 100 X 50 X 6 X 1000Mm. Fixing Of 11 Kv Switchgears Rag Bolt, Mounting Ofp.T. On Incoming. 69 11 Kv In Coming 70 11 Kv O / G Vcb 71 Laying Of 11 Kv 3 X 70 / 120 / 185 / 300 Sqmm. Xlpe Power Cable By Digging 0.75 Mtr. Deep Trench, Putting Layer Of Sand In The Bottom, Ramming It, Laying Of Cable Over It Rmt And Covering The Cable From Sides And Top By Laying Bricks, Finally Covering The Same By Earth And Levelling Of The Same, All The Materials, Except Cable, Will Be Provided By The Contractor. Rates May Be Quoted Per Rmt 72 Construction Of Cable Trenchs For L.T. Cable For Station T / F In The Switchyard As Per Direction Of Engineer. Trenchs To Be 12” Wide And 9” Deep. Work Includes Digging, Of Trench, Concreting Of The Foundation In The Ratio 1:3:6 R.B. Wall 9” Wide With Cement Mortar 1:4 And Plastering Inside The Trench In The Ratio 1:3 And Sand Filling In The Trench. Allmaterial Will Be Provided By The Contractor. 73 Erection Of 4No. D / Pole 11 Mtr Long Stppole Including Fixing Of Top Channel On The Top The Pole And Cross Brasing, With The Help Of Clamp For 11 Kv Outgoing Feeder Of 33 / 11 Kv S / S All Material Required For This Work Shall Be Provided By Contractor 74 Erection Of 2No. D / Pole 8.5 Mtr Long Pcc Pole For Substation T / F In Switch Yard Including Fixing Of Top Channel Cross Bracing, S / S Base Angle, Tpmo, Fuse Set And Mounting Of 63 Kva T / F On D / P And Fitting Of All Accessories As Per Resspo Drawing. All Materialrequired For This Work Shall Be Provided By Contractor 75 Cartage Of All Abovematerials Will Be Done By Contractor 76 Termination Of Cable Boxes Of Size 3 X 185 Sqmm. For Xlpe Cable Boxes I / D & O / G Will Be Of Heat Shrink Indoor Type Andoutdoor Type Cable Boxes Will Be Provided By The Contractor 77 Termination Of Cable Boxes Of Size 3 X70 / 120 Sqmm. For Xlpe Cable Boxes I / D & O / Gwill Be Of Heat Shrink Indoor Type Andoutdoor Type Cable Boxes Will Be Provided By The Contractor 78 Laying Of 0.4 Kv Alm. Pvc 4X16mm2 L.T. Power Cable From Sub Station T / F To L.T. Distribution Board. Approx Length Of Cable 100 Mtr. Shall Be Provided By Contractor. 79 Fabrication And Fixing Of Cable Support Channel Of Size 125 X 65 X 6Mm. 3.5 Mtr. Long And Grouting With Mortar 1:3:6 Ratio In Switch Yard.All The Material , Shall Be Provided By The Contractor. 80 Fabrication And Fixing Of Neutral Strip Support Of T / F Made Of 65X65x6mm. 3.5 Mtr. Long And Grouting With Mortar 1:3:6 Ratio In Switch Yard.All The Material Such As Cement, Concrete Except Strip Shall Be Provided By The Contractor. 81 Laying Of Following Copper Control Cable Form C.T. T / F To Transformer Control Pannel / Protection Board. All Control Cable Shall Be Supplied By The Contractor. 82 2X2.5 Mm2 83 4X2.5 Mm2 84 33 Kv Line ( Appx. 23 Km. ) From 132 Kv S / S Jhunsi To 33 / 11 Kv Proposed S / S ( Chamanganj & Malawa ) 85 Supply Of Materials 86 Single Pcc Pole 9.0 M Long 87 Single Stp Pole 11 M Long 88 V-Type Cross Arm 100X50x6 Mm, M.S. Channel ( 7.9 Kg / M, Total Weight 14.5 Kg ) With Holding Clamp 89 Acsr Dog Conductor ( 23 Km Ckt ) 90 Ms Angle 65X65x6 Mm, 3.2 Mtr Long ( 5.8 Kg Per Mtr ) For Guarding With Clamp 91 Top Channel 125X65mm 3200 Mm ( 10.70 Kg. / Mtr. ) With Clamp 92 33 Kv Disc Insulator Polymer 70 Kn 93 33 Kv Disc Fitting 70 Kn 94 33 Kv Pin Insulator Polymer 95 Complete Stay ( Gi Stay Rod 20X1800 Mm, Stay Wire 7 / 8 Swg 10 Kg, Stay Clamp, Bolt, Nut & Washer ) With Concrete Grouting 96 Earthing Of Pole By Ms Earthing Rod Of 20X2500 Mm And 6 Swg Earthing Wire Etc. 97 Gi Wire 6 Swg & 10 Swg For Guarding And Lacing 98 Ms Angle Iron 65X65x6mm, 4300 Mm Long Bracing With Clamp 99 Earth Wire Clamp With Bolt & Nut 100 E-Bracket For 33 Kv 101 F-Bracket For 33 Kv 102 Bolts, Nuts & Washers 103 Danger Board With Clamp 104 Barbed Wire 105 Concreating Of Support With Cement, Sand And Bricks Ballast Ratio 1:4:80.45X0.45X1.5 Mtr. Deep Under The Ground 106 Railway Crossing 107 33 Kv 3X300sqmmxlpe Cable 108 Hdpe Pipe 6 Dia 109 G.I. Pipe 6 Dia 110 3X300 Sqmm Xlpe Cable Jointing Kit 111 M.S. Channel 125X65x6x2400 With Clamp 112 Road Crossing 113 33 Kv 3X300sqmmxlpe Cable 114 Hdpe Pipe 6 Dia 115 G.I. Pipe 6 Dia 116 3X300 Sqmm Xlpe Cable Jointing Kit 117 M.S. Channel 125X65x6x2400 With Clamp 118 33 Kv Line From 132 Kv S / S Jhunsi To 33 / 11 Kv S / S Malawa And Chamanganj 119 Erection Of Work As Per Resspo Norms. 120 Digging Of Pits Of Size 0.45X1.25X 1.50 Mtr. Forerection Of Pcc Pole 9.00 Mtr. Long ( S / P, D / P, T / P, F / P ) 121 Digging Of Pits Of Size 0.45X1.25X 1.85 Mtr. Forerection Of S.T. Pole 11 Mtr. Long For Making S / P, D / P, T / P, F / P, Xing Ht / Lt Line And Canal Etc 122 Erection Of Single Pcc Pole Of 9 Mtr Long. 123 Erection Of Single Pole S.T.P. 11 Mtr Long At X Rings. 124 Fabrication And Erection Of Double Pole Of P.C.C. Poles 9 Mtr Long. 125 Fabrication And Erection Of Double Pole Of S.T.Poles 11 Mtr Long. 126 Fabrication And Erection Of Tri-Pole Structure Of P.C.C. Poles 9 Mtr. 127 Fabrication And Erection Of Tri-Pole Structure Of S.T. Poles 11 Mtr. 128 Fabrication And Erection Of Four Pole Structure Of P.C.C. Poles 9 Mtr. 129 Fabrication And Erection Of Four Pole Structure Of S.T. Poles 11 Mtr. 130 Mounting And Fitting Of V-Type Cross Arm, 33 Kv Pin, Pin Insulator, Earth Clamp Complete In All Respect As Per Drawing Of Respo On Single Pcc Pole 9 Mtr Long And Single S.T. Pole 11 Mtr Long. Cross Arm, Pin, Pin Insutator, Cross Arm Cramp, Danger Board With Clamp Shall Be Provided By Contactor. 131 Fabrication, Mounting And Fitting Of Top Channel, Bracing Made Of M.S. Angle, Earth Clamp, 33 Kv Pin & Pin Insulators, Disc Insulator Anddisc Fitting On P.C.C. Ands.T.P. Double Pole.Top Channel Bracing M.S. Angle, 33 Kv Pin And Pin Insulator. Disc Insulator And Disc Fitting , Earth Clamp, Stay Clamp, Top Channel Clamp, Bracing Clamp, Danger Board Etc. Shall Be Provided By Contractor. 132 Fabrication, Mounting And Fitting Of Top Channel, Bracing Made By M.S. Angle, Earth Clamp, Danger Board, Pin And Pin Insulators, Disc And Disc Fitting On Tri-Pole Structures. Pcc 9 Mtr. / Stp 11 Mtr. Top Channel Bracing, Pin And Pin Insulator, Disc And Disc Fitting , Stay Clamp, Top Channel Clamp, Bracing Clamp, Earth Clamps And Danger Board Etc. Shall Be Provided By The Contractor. 133 Fabrication, Mounting And Fitting Of Top Channel, Bracing Made By M.S. Angle, Earth Clamp, Danger Board, Pin And Pin Insulators, Disc And Disc Fitting On Four Pole Structures. Pcc 9 Mtr. / Stp 11 Mtr. Top Channel Bracing, Pin And Pin Insulator, Disc And Disc Fitting Stay Clamp, Top Channel Clamp, Bracing Clamp, Earth Clamps And Danger Board Etc. Shall Be Provided By The Contractor. 134 Grouting Of Single Pcc Pole 9 Mtr Long With Cement, Sand And Brick Bllast Ratio 1:4:8 Size 0.45X 0.45X 1.5 Mtr Deep Under The Ground As Per Drawing No. Res-6.Cement, Sand, Brick, Ballast Shall Be Provided By The Contractor. ( S / P, D / P, T / P, F / P ) 135 Grouting Of Single S.T. Support 11 Mtr Longwith Cement, Sand And Brick Ballast In Ratio 1:4:8 Size 0.45X 0.45X1.85 Mtrdeepunderthe Ground And 0.45X 0.45X 0.45 Mtr Above The Ground Including Plastering And Polishing With Neat Cement ( It Includes The Grouting Of St Poles Of Single Pole Support, Double Poles, Tripole And Four Pole Structures. ) Cement, Sand, Brick, Ballast Shall Be Provided By The Contractor. 136 Digging Of Pits Of Size 0.60X 0.60X1.2 Mtr And Grouting The Stay Rod Anchor Plates 0.45X 0.45X 0.45 Mtr With Cement, Jamuna Sand And Brick Ballast Ratio 1:4:8 As Per Drawing No. Res-16. Cement, Sand, Brick, Ballast Shall Be Provided By The Contractor. 137 Complete Fitting Of Stay Rod And Fastening Stay Wire Including Fitting Of Stay Clamp, Turn Buckle, And Making Ring Of Stay Wire On Both Ends In Seven Strands9” To 12” Long. Stay Clamp, Turn Buckle Shall Be Provided By Thecontractor. 138 Earthing Of Single Pcc / St Pole By Digging 1.00 Mtr Deep Pit And Driving The Electrodes Of Ms Earth Rod And Connecting All The Metallic Parts Of Poles With Earthing Rod By G.I. Wire And Filling Pits With Soil After Completion Of Earthing.Earth Wire / G.I. Wire M.S.Rod Shall Be Provided By The Contractor. 139 Work Of Road, Canals, Telephones And H.T. Line Crossing By Providing Guarding Angles / Channels On Supports And Fabrication And Fiting Of Guarding Net As Per Drawing No. 48 With G.I. Wire No. 8 / 10 Swg, Guarding Angle Except Guarding Angle Andg.I. Wire All Other Materials Provided By The Contractor. 140 Laying Of A.C.S.R. Dog Conductor With Thehelpof Aluminium Roller By Hanging Three Nos. On Each Support In A Manner Taking Sufficient Care To Ensure Safety Of A.C.S.R. Dog Conductor Against Rubbing On Ground, Precaution For Safety Of Crops Is Also To Be Taken. The Work Includes Jointing Of Conductor By Providing Jointing Sleaves, Stringing Of Conductor Upto Correct Sag And Binding Of Conductor With Insulators On Each Support.All Material Required For Above Work Shall Be Provided By Contractor Such As Jointing Sleeve Binding Wire, Armour Rod Etc. 141 Railway Crossing 142 Road Crossing 143 Loading Carriage And Unloading Of Following Line Materials 144 P.C.C. 9 Mtr. Long. 145 Stp 11 Mtr. Long. 146 Acsr Dog Conductor. 147 33 Kv 3X300 Sqmm Xlpe Cable 148 Hdpe Pipe 6 Dia 149 Other Items As Per Requirement For Construction Of Line ( Disc, Disc Fitting, X-Arm. Pin, Pin Insulator, Stay Rod, Earth Rod, M.S. Rod, G.I Wire Etc. 150 Trimming Of Tree Branch Big / Small Branch Which Is Laying In Alignment Of33 Kv Line From 220 / 132Kv S / S Jhunsito Tapping Point 33 / 11 Kv Linemalawa And Chamanganjdist. Prayagraj. 151 Big Branch 152 Small Branch 153 Jumpring Of33 Kv Line On 33 Kv Bay Using P.G. Clamp Dog To Dog& Dog Conductor & Binding Of Jumper And Other Accessories On Terminal Gantry At 33 / 11 Kv S / S Malawa And Chamanganjdisst. Prayagraj.Binding Wire & P.G. Clamp, Aluminiumlug Etc. Provided By Contractor. 154 Construction Of Control Room Building, Boundary Wall , Road & Other Misc. Civilwork At 33 / 11 Kv Substation- Chamanganj & Malawa 155 Clearing Jungle Including Uprooting Of Rank Vegetations, Grass, Bush, Wood, Trees And Saplings Of Girth Upto 30Cm Measured At A Height Of 1.0M Above Ground Level And Removal Of Rubbish Upto A Distance Of 50M Outside The Periphery Of Uppcl Area Cleared. ( Csi No. 4.08 ) 156 Excavation In Foundation In Ordinary Soil ( Loam Clay Or Sand ) Including Lift Upto 1.5M And Lead Upto 30M And Including Filling, Watering And Ramming Of Excavated Earth Into The Trenches Or Into The Space Between The Building And Sides Of The Foundation Work. ( Csi No. 4.01 ) 157 Concrete With 4Cm Gauge I Class Brickballast, Coarse Sand And Cement In Proportion Of 12:6:1 In Foundations And Under Floors Including Supply Of All Materials, Labour And Tools And Plants Etc. Required For Proper Completion. ( Csi No.5.01 ) 158 Concrete With 4Cm Gaugestone Ballast, Coarse Sand ( F.M. 1.8 To 2.5 ) & Cement In Proportion Of 12:6:1 In Foundations &Under Floors Including Supply Of All Materials, Labour And Tools And Plants Etc. Required For Proper Completion. ( Csi No. 5.02 ) 159 Tmt / Tor Steel In Plain Work Such As Reinforced Concrete Orreinforced Brick Work ( When Not Included In An Over All Rates ) Wrought To Required Shape As Necessary Including Bending Forproper Completion Of The Work And Including Supply Of Steel Its Wastage, Bend, Hooks And Authorized Overlapping Shall Be Measured. ( Steel Shall Be Arranged By The Contractor ) ( Csi No. 9.03 ) 160 Rcc Work With Cement Approved Coarse Sand ( F.M. 1.8 To 2.5 ) And2 Cm Gauge Graded Approved Hard Stone Ballast Like Grainite, Quartzite Etc From Dalla, Jhansi Or Other Quarries And Approved Coarse Sand In Proportion1:1.5:3 In Raft Foundation And Footings , Excluding Supply Of Reinforcement & Its Bending But Including Its Fixing And Binding The Same With Binding Wire, Including Cost Of All Other Materials Labour And T&P. ( Csi No. 5.27 ) 161 Rcc Work With Cement Approved Coarse Sand ( F.M. 1.8 To 2.5 ) And2 Cm Gauge Graded Approved Hard Stone Ballast Like Grainite, Quartzite Etc From Dalla, Jhansi Or Other Quarries And Approved Coarse Sandin Proportion 1:1.5:3In Rcc T Beam-Slab And Column , Excluding Supply Of Reinforcement & Its Bending But Including Its Fixing And Binding The Same With Binding Wire, Including Cost Of All Other Materials Labour And T&P . ( Csi No. 5.29 ) 162 First Class Brick ( Class-150 ) Work In 1:6 Cement And Coarse Sand ( F.M.1.8 To 2.5 ) Mortar In Foundation And Plinth Including Supply Of Allmaterials, Labour & T&P Etc. Required For Proper Completion Of Work. ( Csi No. 6.01 ) 163 First Class Brick ( Class-150 ) Work In 1:4 Cement And Coarse Sand ( F.M.1.8 To 2.5 ) Mortar In Superstructure For Walls Of 1 / 2 Brick ( 115 Mm ) Thickness Including Supply Of Allmaterials, Labour& T&P Etc. Required For Proper Completion Of Work ( Csi No. 6.03+6.07+6.09 ) 164 Earth Filling Under Floors And / Or Sub Station Area Including Cost Of Earth When Obtained From With In 8 Kmoutside Uppcl Area Including Its Roylty And Carriage Including Watering, Ramming In 20 Cm Layers And Dressing Of Earth Etc. All Complete. ( Csi No. 4.10 ) 165 Local Sand Filling In Plinth Including Supply Of Necessary Quantity Oflocal Sand From Outside The Uppcl Premises Including Watering, Dressing Etc. Rate To Include Cost Of All Materials, Labour And T&P Etc. Required For Proper Completion Of Work. ( Csi No. 4.05 ) 166 Pre-Construction Anti-Termite Treatment, By Creating A Barrier Under And Around The Columns Pits, Foundation Trenches, Under Floors, Junctions Of Walls &Floors, Around The External Perimetre Of Building, Expansion Joints, Surrounding Of Pipes And Coduits Etc. ( Plinth Area Of The Building At Ground Floor Only Shall Be Measured As Per I.S. 6313 ( Part Ii 1981 ) ) With Aldrine Emulsifiable 0.2% Concentration Or Any Other Approved Material Such As Heptachlore Or Chlordance Will Be Used. The Consumption Of Emulsion Shall Be ( I ) Foundation And Masonary @ 5 Ltrs / Sqm, ( Ii ) Back Fills In Immediate Contact Of Foundation@ 7.5 Ltrs. / Sqm, ( Iii ) Top Surface Of Plinth Filling @ 5 Ltrs / Sqm, ( Iv ) Junction Of Walls & Floors @ 7.5 Ltrs / Sqm, ( V ) Soil Along External Perimetre Of Building @ 7.5 Ltrs / Sqm ( Vi ) Under Apron Of The Building @ 5 Ltrs. / Sqm. The Rates Includes Cost Of All Materials, Labour, Equipments, T&P Complete. ( Csi No. 17.01 ) 167 Cement Concrete With 2Cm Gauge Approved Hard Stone Ballast, Coarse Sand ( F.M. 1.8 To 2.5 ) And Cement In Proportion Of 1:1.5:3. Including Supply Of All Materials, Labour, Side Shuttering If Required And T&P Etc. Required For Proper Completion Of Work ( Csi No. 5.21 ) 168 Mild Steel Or Iron Work In Heavy Sizes Such As Trusses Built Upgates, Door Frames, Record, Racks Roof Work Gates Etc. Wrought Torequired Form Including Holes Rivetting Or Welding Where Necessary And Also Fixing In Proper Position And Alignment Including Cost Of All Materials Supplied By Contractor. ( Csi No. 9.01 ) 169 First Class Brick ( Class-150 ) Work In 1:6 Cement And Coarse Sand ( F.M.1.8 To 2.5 ) Mortar In Super Structure A Including Supply Of Allmaterials, Labour & T&P Etc. Required For Proper Completion Of Work. ( Csi No. 6.01+6.07+6.08 ) 170 Providing And Fixing Steel Glazed Window And Ventilators Ofstandard Rolled Mann Or Mahavir Steel Sections Conforming To Is7452-1974 As Per Drawing Joints Metered & Welded With 100X14x3.15 Mm Holdfast Embedded In Cement Concrete Block 15X10x10 Cm. Size Of 1:3:6 Proportion I.E. First Part Of Cement 3 Part Of Approved Coarse Sand & 6 Part Of Graded Stone ( Aggregated 20Mm. Nominal Size ) S / F Of Glass Panes Of Plain Pin Headed 4Mm. Thick Nuts Glazing Clips And Special Putty Of Approved Make Complete And Including A Cost Of Red Oxide Paint. The Fabrication Should Conform To I.S.1038-1975. ( Aluminum Beading With Rubber Packing Included ) . ( Csi No. 9.17 ) 171 Rcc Work With Cement Approved Coarse Sand ( F.M. 1.8 To 2.5 ) And2 Cm Gauge Graded Approved Hard Stone Ballast Like Grainite, Quartzite Etc From Dalla, Jhansi Or Other Quarries And Approved Coarse Sand In Proportion 1:1.5:3In Lintels Of Doors And Windows, Excluding Supply Of Reinforcement & Its Bending But Including Its Fixing And Binding The Same With Binding Wire, Including Cost Of All Other Materials Labour And T&P. ( Csi No. 5.23 ) 172 Cement Concrete With 2Cm Gauge Approved Hard Stone Ballast, Coarse Sand ( F.M. 1.8 To 2.5 ) And Cement In Proportion Of 4:2:1Including Supply Of All Materials, Labour, Side Shuttering Ifrequired And T&P Etc. Required For Proper Completion Of Work. ( Csi No. 5.06 ) 173 Rcc Work With Cement Approved Coarse Sand ( F.M. 1.8 To 2.5 ) And2 Cm Gauge Graded Approved Hard Stone Ballast Like Grainite, Quartzite Etc From Dalla, Jhansi Or Other Quarries And Approved Coarse Sand In Proportion 1:1.5:3Inslab, Excluding Supply Of Reinforcement & Its Bending But Including Its Fixing And Binding The Same With Binding Wire, Including Cost Of All Other Materials Labour And T&P. ( Csi No. 5.24 ) 174 S / F Hexagonal Fan Box With Hexagonal Side Of Approx 80Mm In Length Fabricated From 16Swg Ms Sheet Incorporating 10Mm Dia Ms Round Bar Duly Bend For Supporting Fan Hanger, Duly Painted With Red Oxide And Screw Arrangement And With Wiring Conduit Laid In The Rcc Roof Before Concreting Alongwith Supply Of All Material Labour T&P Etc. Required For Proper Completion Of Work As Per Direction Of Eic. ( Nsi ) 175 12 Mm Thick Plaster With Cement Mortar Consisting Of One Part Of Cement & Three Part Of Coarse Sand ( 1:3 ) , Minimum Thickness Not To Be Less Then 10 Mm Including Supply Of All Materiallabour And T&P Etc For Proper Completion Of Work. ( Csi No. 11.06 ) 176 6 Mm. Thick Plaster With 1:3 Cement & Coarse Sand Includinglabour, Materials & T&P Etc. Required For Proper Completion Ofthe Work. ( Csi No. 11.17 ) 177 3 Mm Thick Floating Coat Of Neat Cement Finish Including Supply Of All Materials, Labour And T&P Etc. Required For Proper Completion Of The Work. ( Cement Consumtion 0.044 Bag / Sq.M. ) ( Csi No. 11.20 ) 178 S / Mixing Approved Water Proofing Compound ( Cico, Dr Fixit Etc ) In Cementmortar In Plaster Or Concrete Work In The Proportion As Recommended By The Manufacturer. ( Csi No. 11.15 ) 179 12 Mm Thick Plaster With Cement Mortar Consisting Of One Part Of Cement & Four Part Of Coarse Sand ( 1:4 ) , Minimum Thickness Not To Be Less Then 10 Mm Including Supply Of All Material, Labour And T&P Etc For Proper Completion Of Work. ( Csi No. 11.07 ) 180 12 Mm Thick Plaster With Cement Mortar Consisting Of One Part Of Cement & Six Part Of Coarse Sand ( 1:6 ) , Minimum Thickness Not To Be Less Then 10 Mm Including Supply Of All Material, Labour And T&P Etc For Proper Completion Of Work. ( Csi No. 11.09 ) 181 Add For Extra Labour And Materials For Plaster Over Rough Face Ofone Brick Thick Wall. ( Csi No. 11.12 ) 182 Providing ( 12X15 ) Mm Section Groove In Plasterincluding All Material, Labour Andt&P Etc. Required For Proper Completion Of The Work. ( Csi No. 11.16 ) 183 Making Drip Course ( 25X12 ) Mm In 1:2 Cement And Course Sandincluding Supply Of All Materials, Labour And T&P Etc Requiredfor Proper Completion Of Work. ( Csi No. 11.19 ) 184 Providing M.S. Frames Work, Rack Etc For R.C.C. Trench Covers And Edging With M.S. Angles And M.S Reinforcement Including Cutting, Bending And Welding As Per Approved Drawing. Therate Is Including Cost Of All Labour, Materials Etc. As Required For Proper Completion Of The Work. ( Csi No. 9.20 ) 185 Fixing Of Cable Trench Edging In Proper Position And Alignment Including Cost Of All Labour, Material And T&Petc. Required For Proper Completion Of The Work ( Labour Rate Only ) . ( Csi No. 9.30 ) 186 Concreting Of 40 Mm Thick Rcc Trench Covers In Mild Steel Framework With Rcc 1:1.5:3 In Cement, Chopan Coarse Sand ( F.M. 1.8 To 2.5 ) And 2Cm Gaugegraded Hard Stone Ballast With 3Mm Thick Floating Coat Of Neatcement Finish On Top Of Cover Complete With All Labour, Materials And Placing The Same In Proper Position At Required Location Of Cable Trench Within The Substation Area. ( Csi No. 5.18 ) 187 4.0 Cm Thick 1:2:4 Plain Cement Concrete Floor With Cement, Approved Coarse Sand & 2Cm Graded Approved Stone Ballast Laid In Panels Finished With 3Mm Floating Coat Of Neat Cement Or Cement And Marble Dust In Ratio Of 5:1 As Specified And Removing Any Overlapping Mortar At The Joints Of The Panels If Any And Giving Them A Uniform Finish Including Supply Of All Materials, Labour And T&P Etc, Required For Proper Completion Of The Work. Without Base Cc ( Csi No. 12.04 ) 188 Providing And Fixing Glass Strips Of 3.15 Mm Thickness & 40Mm Depth In Jointsof Floor And Skirting At The Time Of Laying Floors, Flush Withfloor Level Including Supply Of All Materials, Labour& T&P Etc. Completion Required For Proper Completion Of Work. ( Csi No. 12.14 ) 189 Supply Of 80 Mm Thick I Shaped Mechanically Compressed Inter Locking Cement Concrete Paver Block Manufactured By High Pressure & Controlled Vibration Machine Having Plan Dimension 200X ( 160+120 Mm ) With Minimum 5 Mm Thick Toping Of O.P.Cement Mixed With 25% Marble Powder. The Compressive Strength Of Concrete Pavers Blocks Shall Not Be Less Than 30 Mpa & 4.5 Kg / No. Including Cost Of All Material, Labour, T&P Etc. Required For Proper Completion Of Work As Directed By Engineer-In-Charge But Excluding G.S.T. Which Shall Be Paid Extra As Per Rules. ( Csi No.12.23 ) 190 Straight Over Burnt Bricks On Edge Floor Laid Dry, Joints Sand Filled, Including Preparation Of Base To Proper Slope And Its Rammingincluding Supply Of All Material Labour & T&P Etc. Required Forproper Completion Of The Work. ( Csi No. 12.09 ) 191 Supply And Fixing Galvanised Mosquito Proof Jali ( 16X24 Gauge ) Withm.S. Flat Of 20 X 3 Mm. Size, On Both Sides Screwed Or Welded To Windowor Door Frame. ( Csi No. 9.18 ) 192 Providing And Laying Floor Of 8 Mm Thick Vitrifiedtiles In Flooring Or Skirting Of Approved Brand ( Bell, Johnson Or Equi. Make ) Size Of 600X600 Mmof Approved Shade, Colour And Pattern , Laid Over Base Cement Mortar 1:4 Mix Including Finishing The Joints With White Cementmixed With Pigment To Match The Shade Of Tile Including Cost Of All Material, Labour And T&P Required For Proper Completion Of The Work. ( Csi No. 12.18 ) 193 Supply And Laying 8 Mm Thickglazed Floor Tiles Of Somany, Johnson Or Equivalent Make, Of Size 300X300 Mm, Laid With1:3 Cement And Approved Coarse Sand Mortar Finished With Whitecement Slurry, Jointing And Polishing Complete, Including Supplyof All Materials, Labour And T&P Etc. Completion Required For Proper Completion Of The Work. ( Csi No. 12.11 ) 194 Supply And Laying 6 Mm Thickglazed Tiles Of Size 300X450 Mm In Skirting / Dado Laid With1:3 Cement And Approved Coarse Sand Mortar Finished With Whitecement Slurry, Jointing And Polishing Complete, Including Supplyof All Materials, Labour And T&P Etc. Completion Required For Proper Completion Of The Work. ( Csi 12.12 ) 195 Supply And Filling Brick Bat In Soak Pit Including All Labour, Material And T&P Etc Complete. ( For 01 Soak Pit ) ( Csi No. 6.23 ) 196 First Class Brick ( Class-150 ) Laid Dry In Foundation And Plinth As Incircular Soakpit Walls Of One Brick Thickness And 2.0 To 3.0M Depthincluding Cutting Moulding Bricks As Required Including Cost Ofall Materials Labour And T&P Complete. ( Csi No. 6.16 ) 197 Providing And Fixing 15 Mm Dia B-Class Jindal, Jtc, Isi Marked G.I. Pipes Complete With Special Such As Bend, Tee, Socket, Cross, Clamp Etc Earth Work Including Filling The Trenches Etc Required For Proper Completion Of The Work. The Rate Also Includes Concealed Gi Fitting Where Required, Cutting And Making Good The Walls Etc And All Materials, Labour And T&P Complete. ( Csi No. 26.01A ) 198 Providing And Fixing 20 Mm Dia B-Class Jindal, Jtc, Isi Marked G.I. Pipes Complete With Special Such As Bend, Tee, Socket, Cross, Clamp Etc Earth Work Including Filling The Trenches Etc Required For Proper Completion Of The Work. The Rate Also Includes Concealed Gi Fitting Where Required, Cutting And Making Good The Walls Etc And All Materials, Labour And T&P Complete. ( Csi No. 26.01B ) 199 Providing And Fixing 25 Mm Dia Jindal, Jtc, Isi Marked G.I. Pipes Complete With Special Such As Bend, Tee, Socket, Cross, Clamp Etc Earth Work Including Filling The Trenches Etc Required For Proper Completion Of The Work. The Rate Also Includes External Gi Fitting Where Required, Cutting And Making Good The Walls Etc And All Materials, Labour And T&P Complete. ( Csi No. 26.02C ) 200 Providing And Fixing 32 Mm Dia Jindal, Jtc, Isi Marked G.I. Pipes Complete With Special Such As Bend, Tee, Socket, Cross, Clamp Etc Earth Work Including Filling The Trenches Etc Required For Proper Completion Of The Work. The Rate Also Includes External Gi Fitting Where Required, Cutting And Making Good The Walls Etc And All Materials, Labour And T&P Complete. ( Csi No. 26.02D ) 201 Providing & Fixing Half Turn 32Mm Dia Gate Valve, Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.05D ) 202 Providing & Fixing Half Turn 25Mm Dia Gate Valve, Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.05C ) 203 P / Fbrass Angle Valve 15 Mm Dia ( 400 Gsm ) Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.16I ) 204 Providing And Fixing Cp Brass Bib Cock15 Mm Dia. Heavy Quality ( 400Gm ) ( L & K And Equi. ) Fittings, Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.16A ) 205 Providing And Fixing Cp Brass Piller Cock Heavy Quality ( L&K Or Equi. ) Fittings, Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.16J ) 206 Providing And Fixing First Quality White Glazed Orissa Pattern W.C.Pan Hindustan, Cera Make. Size 580 Mm. ( Hindustan, Cera Make ) With Out P Trapincluding Supply Of All Materials, Labour And T&P Etc.Complete. ( Csi No. 27.01 ) 207 Providing And Fixing Pvc Connection Pipe, 450X15 With 2 Brass Units Isi Mark Heavy Quality Including Supply Of All Materials, Labour And T&P Required For Proper Completion Of Work. ( Csi No. 26.09B ) 208 Providing And Fixing In Position 32 Mm. Dia P.V.C.Waste Pipe For Wash Basin. Including Supply Of All Materials, Labour And T&P Etc.Required For Proper Completion Of The Work. ( Csi No. 27.14 ) 209 Providing And Fixing 100 Mm Dia Pvc P Or S Trap Including Cement Concrete And All Materials, Labour Cartage T&P Etc.Required For Proper Completion Of The Work. ( For W.C. ) ( Csi No. 27.24 ) 210 Providing And Fixing 10 Littres Low Level Pvc Flushing Cistern, Complete With All Fittings Including Supply Of All Materials, Labour And T&P Etc. Required For Proper Completion Of The Work. ( Csi No. 27.12 ) 211 Providing And Fixing In Position 32 Mm. Dia P.V.C. Flush Pipe. For W.C. With Unions, Bends Etc. Including Supply Of All Materials, Labour And T&P Etc.Required For Proper Completion Of The Work. ( Csi No. 27.13 ) 212 Supply And Fixing 100 Mm Dia Pvc Nahani Trap India Make Of Heavy Approved Quality Complete With Grating, Includingsupply Of All Materials, Labour And T&P Etc. Required For Proper Completion Of The Work. ( Csi No. 27.21B ) 213 Providing And Fixing 550X400 Mm Wash Hand Basin Of White Glazed Earthern Ware First Quality I.S.I. Marked ( Hindustan, Neycer / Cera Make ) Including Supply Of All Materials, Labour And T&P Etc. Required For Proper Completion Of The Work. ( Csi No. 27.08 ) 214 Supply And Fixing Of Syntex Or Equivalent Make Water Storage Tank Including All Materials, Labours, T&P Etc Required For Proper Completioon Of Work. ( Csi No. 26.12 ) 215 Providing And Fixing Of 110 Mm Dia Pvc Pipe 6 Kg / Sq.Cm Forwith Special Such As Tee, Bend, Socket, Elbow Etc Including Supply Of All Labour, Material, T & P Etc Complete Required For Proper Completion Of Work. ( Csi No. 26.17 ) 216 Providing And Fixing 600 Mm X 450 Mm Beveled Edge Mirror Of Atul, Kiran Makeglass With Indian Polish 6.50 Mm Thick Complete With Back Of 600 Mm X 450 Mm X 6 Mm Hard Board Sheet Fixed To Wooden Cieats With C.P. Brass Screws And Washers Including Supply Of All Materials, Labour And T&P Etc.Required For Proper Completion Of The Work. ( Csi No. 27.15 ) 217 Applying Birla Or Equivalent Putty On New Interior Or Exterior Surface Over One Coat Of Water Based Cement Primer Of Ici Or Equivalent Brand For Smoothening And Levelling Of The Surface As Per Requirement And Direction Of Engineer I / C Including Cost Of All Material, Labour, T & P Etc Required For Proper Completion Of Work. ( Csi No. 13.20 ) 218 Painting Two Coat With Acrylic Emulsion Paint Of Berger / Asian / Ici Or Equivalent Paint ( Paint And Water In The Ratio 1:1 By Volume ) Over Prepared And Primed Surface Of Cement Concrete, Cement Plaster And Bricks Including All Labour, Material And T&P Etc Required For Proper Completion Of The Work, ( Preparation Of Base With Birla Putty Etc. And A Coating Of Primer Shall Be Paid Extra ) . ( Csi No. 13.25+13.26 ) 219 Painting Two Coat With Apex Or Equivalent Brand Weather Coat Paint On New Wall Surfaces ( Well Prepared With Birla Putty And One Coat Of Primer Ici Or Equivalent Which Shall Be Paid Separately ) Including Through Washing With Water Including Cost Of All Materials, Labour, T&P Required For Proper Completion Of Work. ( Csi No. 13.22+13.23 ) 220 Painting Or Varnishing New Iron Works Or New Wood Work With One Coat Of Ready Mixed Priming Paint And Two Coats Of Approved Superior Quality Ready Mixed Paint Luxol Or Equivalent Brand Or Varnish Including Supply Of All Materials, Labour& T&P Etc. Required For Proper Completion Of The Work ( C.S.I. No. 13.01+13.02 ) 221 Grouting Of Vertical Or Inclined Post Of Pale / Chain / Security Fencing In Truelevel, Alignment And In Plumb Or Inclination As Required, Including Cost Of All Labour, Materials And T&P Required Forproper Completion Of Work. ( Post And Concrete For Grouting Shall Be Measured Separately ) ( Csi No. 9.28 ) 222 P / F Concertina Coilfencing With Required Dia. 600 Mm Upto 3 M Height Of Wall Between Existing Angle Iron ‘Y’ Shaped Placed 2.4 M Or 3.0 M Apart And With 6 Horizontal R.B.T. Stud Tied With G.I. Staples And G.I. Clips To Retain Horizontal Including Necessary Golts Or G.I. Barbed Wire Tied To Angle Iron All Complete ( No. Of Rounds Will Be 7 To 8 In One Meter Length ) As Per Direction Of Engineer I / C With Reinforced Barbed Tape ( R.B.T. ) / Spring Core ( 2.5Mm Thick ) Wire Of High Tensile Strength Of 165 Kg / Sqmm With Tape ( 0.52 Mm Thick ) Of Supreme Make Or Equivalent And Weight 43.478 Gm / Meter ( Cost Of Ms Angle, C.C. Blocks Shall Be Paid Separately ) . ( Csi No. 9.37 ) 223 Wiring Point For Lightwith 1.5 Sq. Mm Frlsh Pvc Insulated Multistrand Single Core Copper Conductor Cable In Pvc Conduit Pipe Concealed In The Wall With 1Sqmm Frlsh Pvc Insulated Multistrand Copper Conductor Cable As Earthwire Drawn Inside The Conduit Piano Type Switch And Ceiling Rose / Angle / Batten Holder On 3Mm Thick Phenolic Laminated Backelite Sheet Etc, Complete In All Respects, As Directed, Including Maching Colour Wash. ( Nsi ) 224 Wiring Point For Fan / Fresh Air Fan ( Light Duty Exhaust Fan ) With 1.5 Sq. Mm Frlsh Pvc Insulated Multistrand Single Core Copper Conductor Cable In Pvc Conduit Pipe Concealed In The Wall With 1Sqmm Frlsh Pvc Insulated Multistrand Copper Conductor Cable As Earthwire Drawn Inside The Conduit Piano Type Switch And Ceiling Rose / Angle / Batten Holder On 3Mm Thick Phenolic Laminated Backelite Sheet Etc, Complete In All Respects, As Directed, Including Maching Colour Wash. ( Nsi ) 225 Wiring Point For Exhaust Fan With 1.5 Sq. Mm Frlsh Pvc Insulated Multistrand Single Core Copper Conductor Cable In Pvc Conduit Pipe Concealed In The Wall With 1 Sqmm Frlsh Pvc Insulated Multistrand Copper Conductor Cable As Earthwire Drawn Inside The Conduit, 15A Piano Type Switch And Ceiling Roseon 3Mm Thick Phenolic Laminated Backelite Sheet Etc, Complete In All Respects, As Directed, Including Maching Colour Wash. ( Nsi ) 226 Wiring Point For Plug With 1.5 Sq. Mm Frlsh Pvc Insulated Multistrand Single Core Copper Conductor Cable In Pvc Conduit Pipe Concealed In The Wall With 1 Sqmm Frlsh Pvc Insulated Multistrand Copper Conductor Cable As Earthwire Drawn Inside The Conduit, Piano Type Switch And Ceiling Rose / Angle / Batten Holder On 3Mm Thick Phenolic Laminated Backelite Sheet Etc, Complete In All Respects, As Directed, Including Maching Colour Wash. ( Nsi ) 227 S / F Of Switch Box Made Of 16Swg ( 1.5Mm ) Thick Ms Sheet Of 100X100x65mm Size Duly Painted With Red Oxide Primer And Flush With Wall Including Cutting Of Brickwork Fixing It To Level With Cement Sand Mortar Including Matching Color Wash With All Materials Labour And T&P Required For Proper Completion Of Work As Directed At Site By The Eic. ( Nsi ) 228 S / F Of Switch Box Made Of 16Swg ( 1.5Mm ) Thick Ms Sheet Of 150X150x65mm Size Duly Painted With Red Oxide Primer And Flush With Wall Including Cutting Of Brickwork Fixing It To Level With Cement Sand Mortar Including Matching Color Wash With All Materials Labour And T&P Required For Proper Completion Of Work As Directed At Site By The Eic. ( Nsi ) 229 S / F Of Switch Box Made Of 16Swg ( 1.5Mm ) Thick Ms Sheet Of 175X100x65mm Size Duly Painted With Red Oxide Primer And Flush With Wall Including Cutting Of Brickwork Fixing It To Level With Cement Sand Mortar Including Matching Color Wash With All Materials Labour And T&P Required For Proper Completion Of Work As Directed At Site By The Eic. ( Nsi ) 230 S / F Of Switch Box Made Of 16Swg ( 1.5Mm ) Thick Ms Sheet Of 250X250x65mm Size Duly Painted With Red Oxide Primer And Flush With Wall Including Cutting Of Brickwork Fixing It To Level With Cement Sand Mortar Including Matching Color Wash With All Materials Labour And T&P Required For Proper Completion Of Work As Directed At Site By The Eic. ( Nsi ) 231 Supply And Fixing Of Led Tube Light Of Make Syska, Bajaj Phillips Or Equivalent Make Of 22Watt On Surface Complete Including All Material And T&P Etc In All Respect As Per Direction Of Eic ( Nsi ) 232 Supply And Fixing Of Led Bulb Of Make Syska, Bajaj Phillips Or Equivalent Make Of 12Watt On Surface Complete In All Respect As Per Direction Of Eic ( Nsi ) 233 Supply And Fixing Of Led Flood Light Of Make Syska, Bajaj Phillips Or Equivalent Make Of 100Watt On Surface Complete In All Respect As Per Direction Of Eic ( Nsi ) 234 Supply And Wiring Of Sub Main With Two Nos 2.5 Sq.Mm F.R.P.V.Cinsulated 1100V Grade Multi Strand Single Core Copper Conductor, Cable In 20Mm Dia Heavyduty ( 2Mm Thick ) Pvc Conduit Concealed In Wall With One Number 1.5 Sq.Mm Multi Strand Copper Conductor, Cable As Earth Continuity Wire Drawn In A Conduit . ( Nsi ) 235 Supply And Wiring Of Sub Main With Two Nos 4 Sq.Mm F.R.P.V.Cinsulated 1100V Grade Multi Strand Single Core Copper Conductor, Cable In 20Mm Dia Heavyduty ( 2Mm Thick ) Pvc Conduit Concealed In Wall With One Number 2.5 Sq.Mm Multi Strand Copper Conductor, Cable As Earth Continuity Wire Drawn In A Conduit . ( Nsi ) 236 Supply And Fixing Of 1200Mm Sweep Ceiling Fan Of Make Usha / Havells Or Its Equivalent Makeincluding Supply Of All Material, Labour, T&P Etc. Required For Proper Completion Of Work As Per Direction Of Eic. ( Nsi ) 237 Supplying And Fixing 63A Dp Isolator Of Approved Make ( Havells, Crompton, Anchor Or Equivalent ) Complete Including All Material And T&P Etc In All Respect As Per Direction Of Eic ( Nsi ) 238 Supply And Fixing Of 6 Amps To 32 Amps Mcb 10Ka Havells Or Equivalent Make Including All Materials, Labour And T&P Requiered For Proper Completion Of Work As Per Direction Of Eic ( Nsi ) 239 Supply And Fixing Of Power Plug With 15Amps. 250V. Flush Type Switch And 5Pin 15A-250V. Flush Type Universal Socket In Suitable M.S.Box Of 175X100x50mm Size With Phenolic Laminated Bakelite Sheet Cover 3Mm. Thick Fixed With Brass Machinesscrews And Cup Washer ( Nsi ) 240 Supply And Fixing Of Surface / Flush Mounting 12 Ways Spn Distribution Board With Additional Metal Door Without Mcb Complete In All Respect As Directed By Eic ( Nsi ) 241 Supply And Fixing Of Power Plug With 20Amps. 250V. Flush Type Modular Switch And 5Pin 20A-250V. Flush Type Universal Modular Socket Switch On Concealed Ms Box Including Supply Of All Material, Labour, T&P Etc. Required For Proper Completion Of Work As Per Direction Of Eic ( Nsi ) 242 Supply And Fixing Of Electronic Fan Regulator 120-280V Isi Marked On The Existing Switch Board Incl. Making Connection, Required Mmaterial, Labour T&P Etc. For Completion Of The Work To The Satisfaction Of Eic . ( Nsi ) 243 Supply And Burying Of Safe Earthing Electrode Of T90 ( Hot Dip Galvanised ) Length Upto 2M, Outer Pipre 50Mm , Inner Pipe 25Mm, Terminal Dia 12Mm, Outer Gi Pipe Of 16Swg And Inner Gi Pipe Of 12 Swg With Hot Dip Galvanisation Upto 100 Micron Field With Crystalline Condutive Mixture Having Anti Corossive And Condutive Property With 50Kg Activated Soil ( Bfc ) Capable Of Reducing The Soil Resistivity Wit Good Mixture Of Retaining Capacity Alongwith 30Cm Square Ci Frame With Hinged Cover And Masonry Housing ( From Electrode Terminal To Switch Board, Cost Of 25X3mm Gi Strip Will Be Extra ) Including All Labour , Material And T&P Required For Proper Completion Of Work As Per Direction Of Eic. Nsi 244 Supply And Installation Of India Mark Hand Pump Ii Including 150 Mm Dia , 70M Deep Boring Up To Second Starta Including Supply And Lowering 110Mm To 63Mm Dia Pvc Pipe ( 24M-110Mm & 44M, 63Mm, 6 Kg / Sq.M ) With Required Strainer, Reducer Joining 90 Mm Dia Long Cylinder, 32Mm Dia Gi Pipe 3Mlong Including Supply Anf Filling Of Course Sand Of Approved Quality ( Approx. .15 Cum ) Including Developing The Bore Well To Achive Clear And Sand Free Water For Continous 60 Min. Including Cost Of All Material, Labour And T&P And Its Cartage For Installation Of Hand Pump Complete As Per Drawing Including Construction Of 1.85 M Dia Chabutara With Excavation Of Earth And Laying 25Mm C.C. Floor 1:2:4 With Cement, C.Sand And 20Mm Stone Ballast With Water Proofing Compound Over 100 Mm Thick C.C. 1:6:12 With Cement, C.Sand And 40 Mm Brick Ballast And Making Side Edge 115Mm Thick And 300 Mm Deep With Brick Work 1:4 And Plaster The Same With 1:4 Mix With Neat Cement Finish Also Including 115 Mm Wide Drain In 1:4 Brick Work & Plaster All Around The Periphery Of Plateform Complete Including Supply Of All Materials, Labour And T&P Etc Required For Proper Completion Of Work. Rate As Per Se, 7Th Mandal, Up Jal Nigam, Gorakhpur Letter No 1045 Dt 16.02.15 ( Csi No.28.10 ) 245 Supply And Fixing Of 40.00 Mm Dia G.I. ( B Class ) Column Pipes Jtc / Jindal Make With Column Coupling Socket As Required For Proper Completion Of Workincluding All Labour Material & T&P. ( Csi No. 19.22C ) 246 Supply And Fixing 40 Mm Dia Support Clamps For Column Pipesmade Out Of Ms Flats, Pairs Of Bolt-Nuts Etc Complete With All Material, Labour, T&P. ( Csi No. 19.24D ) 247 Supply & Installation Of 1.5 Hp Outlet 40Mm Dia. Or More, Head 71 / 36, Discharge 2000 / 6000 Lphsubmersible Pump Of K.S.B / Calama. Or Eqt. Make Including Cost Of Labour, T&P And Material Required For Completion Of Work. ( Csi No. 19.32B ) 248 Supply & Installation Of Electrical Control Panel For 1.5 / 2 H.P Pump Set Single Phase Of L&T / Havells Or Equivalent Make For Submersible Pump / Pumpset Containing Contractor Relay Condenser. ( Csi No. 19.31B ) 249 Supply & Fixing Of Steel Wire Rope Forsubmersible Pump Including Cost Of Labour, T&P And Material Required For Completion Of Work. ( Csi No. 19.34 ) 250 Supply And Fixing Of2.5 Mm2 For Pumpabove 1 Hp And Up To 3 Hp. Submersible Cable Havelsor Equivalent Make, For Submersible Pump Complete In All Respect. ( Csi No. 19.33B )
