|
| 1 | A: Exterior WallsExternal Glazing: Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, indluding necessary filling up the gaps at junctions, i.e. at top. bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snab beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.NOTE: Make to be fenesta, beautex, Alupure or equivalentFixed GlazingGlass Sliding doorsGeneric Walls:Bamboo walls to be constructed using a connected grid system with the floor framing as per structural/architectural drawings. The gridsytem is to be curved to follow the design aesthetics and the grids should be made from bambo stripsof atleast 8-10mm in dia. The grids are to be formulated withhelp of steel or rope ties as per final decision from the site engineer. The grids should not be more thean 150mm x150mm. A layer of chicken wiremesh to be fixed again using ties. Bamboo flat panels are to be fixed to the baffle wall using allen key for easy removal. The joints at which the allen keyscreqs are to be tightened must be reinforced with intermedicate wooden battens of a minimum thicknes of 30mm. The outer surface must be waterproofed with a membrane waterproof material and then cladded with thin treated bamboo strips atlest 15mm dia. Complete system to be deisgned in a way that it removable when required and an be re-assembled as soon as possible. NOTE: The bamboo used for grid should be T.Oliverai and for flate bamboo cladding we should use gigantius |
| 2 | B: Interiors WallsGeneric Walls:Bamboo walls to be constructed using a connected grid system with the floor framing as per structural/architectural drawings. The gridsytem is to be curved to follow the design aesthetics and the grids should be made from bambo stripsof atleast 8-10mm in dia. The grids are to be formulated withhelp of steel or rope ties as per final decision from the site engineer. The grids should not be more thean 150mm x150mm. A layer of chicken wiremesh to be fixed again using ties. Bamboo flat panels are to be fixed to the baffle wall using allen key for easy removal. The joints at which the allen keyscreqs are to be tightened must be reinforced with intermedicate wooden battens of a minimum thicknes of 30mm. The inner surface must be waterproofed with a membrane waterproof material and then cladded with thin treated bamboo strips atlest 15mm dia. Complete system to be deisgned in a way that it removable when required and an be re-assembled as soon as possible. NOTE: The bamboo used for grid should be T.Oliverai and for flate bamboo cladding we should use gigantiusKitchen walls:Bamboo walls to be constructed using a connected grid system with the floor framing as per structural/architectural drawings. The gridsytem is to be curved to follow the design aesthetics and the grids should be made from bambo stripsof atleast 8-10mm in dia. The grids are to be formulated withhelp of steel or rope ties as per final decision from the site engineer. The grids should not be more thean 150mm x150mm. A layer of chicken wiremesh to be fixed again using ties. Bamboo flat panels are to be fixed to the baffle wall using allen key for easy removal. The joints at which the allen keyscreqs are to be tightened must be reinforced with intermedicate wooden battens of a minimum thicknes of 30mm. The inner surface must be waterproofed with a membrane waterproof material and then cladded with thin treated bamboo strips atlest 15mm dia. Complete system to be deisgned in a way that it removable when required and an be re-assembled as soon as possible. NOTE: The bamboo used for grid should be T.Oliverai and for flate bamboo cladding we should use gigantius. All interior surfaces to be coated with fire retardent solution AMEETUF or equivalent. With a two coat of injection (20ml)/sq /ft of primary coat and two coat of top coat. |
| 3 | C: FurnitureFabricating and Supply of Floor Mounted Bamboo Outdoor Seaters, Tables with Necessary Ply and MS Framework all complete as per detail drawing.Tables: complete wooden tables with adequate ground support and laminated top. Finished in margins on reveals and plastic bushes below of various sizes ranging from(2400mm-3600mm). Complete with all material and as per drawings.Chairs: Working chairs: Supplying and providing working office chairs with ergonomic high back support for long hours of working, with ventilated mesh fabric and castor wheels at bottom. As per Architects approval. MAKE: transteel or Hardeep designsHigh Chairs and Bar stools: Sofa\"s with upholstery Wooden Strorage: Fabricating 8 feet high wooden storages with laminate /bamboo cladding alongwith margins and two coats of clear polish. Complete with all material and as per Drawings.Bar Counter: With undercounter storage and granite counter top with adequate support. Complete in alla spects as per Architects drawings. |
| 4 | D: Lightsitem includes supplying, assembling, fixing, testing & commissioning Following Fixtures including all accessories, lamps & extension chords as maybe necessary complete. All LED / Flurescent fixtures (except down lighters) to be hung from the RCC ceiling by 20 KG grade adjustable GI chain & in NON False ceiling area they are to be hung by appropriate Down Rods.Providing and Fixing Recessed mounted diffused optics high performance 2\" X 2\" LED luminaire with necessary LED lamp (34W LED 3000K) or similar.Providing and Fixing Recessed mounted LED spot light with necessary LED lamp (15W LED 3000K) or similar. (Ceiling cutout ø 155 mm.)Providing and Fixing Surface mounted 4\" long luminaire suitable for Lamp type 18W LED (T5) or similar |
| 5 | E: UpholsteryUpholstery: Supply and fixing of commercial grade fabric of approved colors and design. Adequate hardware for errection as blinds curtains or sofa/cushion covers. |
| 6 | F: Commercial kitchenSupply errection and commissioning of fully functional commercial kitchen with working sink and equimnet like deepfrezer, Kitchen blender, automatic huice machine, Knife sterlizer,oil heater, vegetable preparation machine with six attachment, pulverizer,masala grinder,potato peeler,, Garbage room,electrc grill and induction oven etc. All cupboards to be of SS grade, racks, shelves, trolley, Dunnage rack,meat collection trolley, vertical chiller, work table with sink and bottom pipe shelf,SS grating with drain trough, vegetable collection trolley, potation adn onion bins, handwash sink foor operated, exhaust hood with baffle filters, fresh air grill, fore suppresion system, stock pot range with ring type burner. And all other items as specified by engineer on site |
| 7 | G: ElectricalS/I/T/Commissioning of 415V, AC 50 Hz, 200 Amp. TPN Main Switch (HRC fuse type - FSF) within steel enclosure at main incoming from SEB / Transformer to be fixed on MS angle framework & 2 nos. cable end box including necessary interconnections.S/I/T/Commissioning of Main Distribution Panel Board as per given below: - 440 Volts AC, 3 Phase, 50 Hz with 50 KA fault level for 1 second, Floor / Wall mounted, 7 tank cleaning process with duly powder coated with copper bus bar. Incomer : 200 Amps 4 Pole MCCB of 35 KA breaking capacity (with earth fault relay) - 1 nos. , with LED type phase indicating lamp, Digital voltmeter, Ammeter with selector switch with required CT unit, Danger Notice Board indicating sign (DANGER) in English, Hindi, Marathi.Outgoing : 40 Amps DP MCB - 2 Nos.,25 Amps 4P MCB - 2 Nos., 25 Amps 2P MCB - 2 Nos., 200 Amp TPN Bus bar Chamber-1 No..Providing & fixing POINT WIRING for Ceiling and wall lights. Point wiring to be laid with 2 x 1.5 Sq. mm. PVC insulated copper conductor with all necessary accessories, such as saddles etc. on surface or embedded in wall, chasing the walls and making the surface neat afterwards. The item includes modular switch 6 AMP with all base plates & cover plates, M.S. box of same make etc. 3 - plate ceiling rose to be provided for Exhaust fans complete. (one light to be controlled by one switch) |
| 8 | H: Sanitary FixturesSupplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. including the cost of closet seat & seat cover, 10 litre pvc cistern, flush pipe, 15 mm. dia. pvc connector pipe,with P/S trap as required. Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing of Wash Basin (550 x 400 mm.) white glazed vitreous china of approved make supplied, incluing the cost of 15 mm .dia pvc connector, 32 mm. dia. pvc waste pipe, ss waste coupling all complete as directed.Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing Chromium plated bib cock including cost of extention pipe & wall flange.Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing Chromium plated health faucet with wall holder including cost of extention pipe.Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing Chromium plated Basin faucet.Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing Chromium plated Basin faucet with wall holder including cost of extention pipe.Make: Cera or QUeo or Equivalent.Supplying, fitting and fixing Chromium plated angular / concealed Stop Cock.Make: Cera or QUeo or Equivalent |
| 9 | I : PlumbingSupplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (Concealed work) CPVC Pipes Class-I,SDR-1115mm dia40mm diaSupplying, fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials).110mm dia |
| 10 | J: Flooring:Providing and fixing VInyl flooring. The flooring shall be fixed with tongue and groove interlocking system, |
| 11 | K: Ceiling CladdingProviding and Fixing bamboo flat panels under the ceiling with adequate framing with ligth holes and spaces for coduits to run. Make: AMEETUF or equivalent |
| 12 | L: Audio SystemProviding and Fixing internal speakers with a centralized PA system and music delivery system. Competent speakers with low latency and high DB volume for ambient music and personal announcement. As per specification provided by the onsite engineer. |
| 13 | M: Server/Wifi /IT systems/UPS systemsComplete wifi solution with wired access points with no black out zones and UPS system to power emergency lights and all TV\"s and computers. |
| 14 | N: Branding/ vinyl/ paintingProviding and fixing of vinyl in cut patterns of different sizes over partitions. Complete with all works. |
| 15 | O: Landscaping + showersComplete outdoor track made from flat pebbel stone or flat stone slabs with coarse sand pavers.Complete with all works. |
| 16 | P: Hume pipes with furnitureProviding and supplying concrete hume pipes with inbuilt electrical routing passage, a central wooden table and fixed seaters. |
| 17 | Q: Outdoor canopy and furnitureProviding and fixing completecanopy in architectural fabric withwooden seaters. |
| 18 | R: HVAC systemComplete HVAC energy efficient system (VRV) with all wires, conduits, packing with all sleeves for both indoor and outdoor units. |
| 19 | S: STPComplete sewage treatment system compliant with environmental norms |
| 20 | T: CIVIL WORKS |
| 21 | T.1 Providing fitting and fixing of STRUCTURAL BAMBOO in all Truss (T) works in complete with dia including all joinery fittings.Selection of Bamboo:Itis one of the most important features of Bamboo Construction Technology because Bamboo is not a standard material varies in size & diameter, wall thickness and tapers towards the top. Therefore, Bamboo has to be selected on the basis of its size, profile and species. The Bambusa balcooah (Bhuluka –Assamese) available commonly in Assam is widely used for this purpose. Bhaluka (Bambusa Balcooa) is brownish green in colour and has distinctive tapers towards the top. It is favoured for construction because of its typical properties and fibers are compact and well built.After the initial sorting of Bamboo on the basis of its dimensional character (Size, Diameter, Height and Wall thickness) and maturity (5 years or above), it is then further cut and sized as per requirement (The average length for structural use from a single pole is about 18ft). The internode portion is now dressed and sanded for a smooth profile. Treatment of Bamboo:Preservation and Treatment of bamboo is the second most essential feature of Bamboo Construction Technology. As Bamboo is a lignu-celluloid (woody) material and rich in starch it is highly prone to fungus attack, powder pest borers and external agents attack. So the longevity of a bamboo depends on the effective treatment. There are various treatment methods and one such economical process used for Bamboo Construction Technology is ‘Internodal injection treatment’ method which can be done on site. Method of Internodal Injection with Creosote Oil: 1. Holes are drilled below the internodes of the bamboos using a 6mm diameter drill.2. With the help of a wash bottle; 25ml of the creosote oil mixed with diesel in equal Proportions are poured inside the bamboos through the drilled holes.3. The holes are then sealed by using putty or wax.4. The bamboos are now allowed to dry under shade for 3 to 4 days to absorb the oil.The bamboos treated by this process can be used for both internal and external use. By this process, borer, termites as well as fungi (decay) can be prevented and the durability of bamboos will increase. The bamboos treated by this method are used for poles (columns), purlins, rafters and other construction materials for house construction. Creosote is an industrial chemical used in road surfacing and needs to be handled with gloves and may not be permitted in certain areas.NOTE: All structural bamboo works should conform to IS 9096 and non structural bamboo works should conform to IS 1902. Area of Use (specifications)T1,T2,T3,T4StrutsArea of Use (specifications) |
| 22 | T.2 Providing and fixing whole cut bamboo cladding over all columns and beams ; encasing the beams for extra protection and for passing of electrical conduits through them. The bamboo should be 2\" larger in diameter and should be cut in 1200mm long pieces and placed with a 2mm hairline gap. In turn the bamboo is to be finished in 2 coats of fire retardant solution.Area of Use (specifications)In Columns In Beams |
| 23 | T.3 Providing and fixing Bamboo mesh panels 25mm thk bent to shape to follow the struts profile and other joinery. Bamboo mesh to be constructed using half cut bambbo of 3\" dia bamboo of length 900mm, held together with bamboo rope/steel wire. All panels are to be nailed with no gaps and should be percieved seamless.Providing fitting and fixing of FLATTENED BAMBOO CLADDING in all Flooring and Roofing in complete with all joinery fittings.Area of Use (specifications)In Columns In Beams |
| 24 | T.4 Providing fitting and fixing of Decorative Bamboo Jallis below roofing in complete with all joinery fittings.Providing and fixing Bamboo mesh panels 25mm thk bent to shape to follow the struts profile and other joinery. Bamboo mesh to be constructed using half cut bambbo of 3\" dia bamboo of length 900mm, held together with bamboo rope/steel wire. All panels are to be nailed with a 10mm gap in one direction (or as per Architects design) for the clading to be perceived seamless.Area of Use (specifications)In Columns In Beams |
| 25 | T.5 Providing fitting and fixing of Railings and Partitions in complete withall joinery fittings.Railings: providing and fixing bamboo balustrades of length 800mm and dia 35mm , spaced at 600mm c/c,cut to shape as per Architect design. With bamboo weave/mesh ( made from half cut bamboo, as per architects designs)panels nailed to the balustrade to form a network of bamboo mesh panels. All bamboo to be finished 1 protective coat of yellow powder and 2 coats of staining acyrlic protective primer. Th erailing to have a 50mm dia bamboo handrail with v grovve beneath for 12mm wide LED profile light as per Architects details. The handrail to be bent and routed as per details specific to design and finished with one coat of yellow powder and 2 coats of protective primer.Partitions: Providing and fixing bamboo walls with complete sub framing/ wall gridsin bamboo. All walls are floor to ceiling (3000mm ) in height. Roof should have wall plates installedas per the walls positions to connect the vertical walls to the horizontal surface.all plates are hard wood of 50 (B) x 100 (W) mm size. It ties bamboo columns togetherand put them in the right alignment. It also provides lateral support to the top of the poleand provides a seat for roof trusses, ceiling, joists and clamping devices. Wall plates are fastened to poles through 100mm screws into hardwood plugs.Wall Grids:Bamboo grids are the main wall supporters. Bamboo strips are tied with steel bar (dowel) to form grids. To prepare grids, you need toInsert 300mm long steel rod of 8-10mm diameter in bamboo columns at 15cm spacing (information about drilling holes in bamboo so as to insert these rods are already provided in section 3.3.1) Tie bamboo strips (15-25 mm width) to the horizontal steel dowel rod of two consecutive columns. Use binding wire to tie the strips with steel rods Once the horizontal parts are finished, fix the vertical strips again at 15cm spacing. You can tie vertical strips with horizontal strips. The top end of vertical strips can be tied to nails fixed to the wall plates. Make sure to leave gaps for doors and window, as per Architects drawings.Cladding: All interior walls to be cladded with flattened bamboo cladding panels of thickness 75mm with an insulation of 50mm 1000gsm Micron sandwiched between and placed in place with chicken wire mesh and all nuts and bolts necessary.Area of Use (specifications) |
| 26 | T.6 Providing and fixing of basework for flatten bamboo panels to be fixed on 19mm ply over 2\"x2\" softwood/40mm stud framework at 2\"-0\" c/c both ways. There will be other layer of 4mm thick ply over 19mm ply to give necessary grooves as per drawing. The framework to be filled with 50mm thick thermal bonded non woven polyster wadding micron fiber of 1000 gm / sqm . The mikron fiber to be held in position with chicken mesh of 18mm & 24SWG. The mikron fiber shall be of Mikasha International/ Sandler and wrapped in LDPE sheet of .7mm thickness.Area of Use (specifications)In Columns In Beams |
| 27 | T.7 Providing fitting and fixing of Steel Structural work as per details in complete including all joinery fittings.WOODEN/TIMBER PILESThe species of timber and their specification shall conform to IS 3629. The diameter of the individial pile shall be the450mm for the length 5m and above. Both ends to be sawn into right angles to the length of the piles and the surface shall be made flush by trimming the knots and limbs. The Timber shall be treated with in accordance with IS 401-1967. All working stresses shall be as given in IS 883. These may be exceede by not more than 100 percent during driving. After Driving , pile tops shall be cut off to a true plane and shall show a solid head at the plane of cutoff. After cutoff the pile tops shall be treated with a preservative in accordance to IS 401. IF the metal top-covers are specified these shall be placed immediately after the treatment. Any holes and cut if required for framing shall be suitably treated.Providing and errection of Round Timber pileswith a minimum diameter of 230mm(atleast 8-10m in length with a wedge shape with a diagonal length of 350mm for ease of drill )oras per specified drawing from the consultant/engineer, in compliance with IS codes 401 and 3629. Piles to be treated with creosote oil or equivalent to prevent any tearing due to moisture buildup. All piles are to be driven in a manner to prevent tearing. Pile caps are to nailed with 3\" long shear connecteors between the plinth primary beams and pile caps.Area of Use (specifications)a) jumbo wooden piles (88.90Q) - Mediumb) C1(a)c)BM1d)BM2e)PLATES, NUTS&BOLTS AND ANGLES |
| 28 | T.8 Providing fitting and fixing of BAMBOO FINISHING WITH YELLOW POWDER and one coat of primer in all Bamboo surfaces in complete. Finishing: Providing and applying all bamboo surfaces with yellow powder or boric acid borax for internal surfaces and with copper chrome acetic for external surfaces in the ratio 5.6:5.6:0.25. With atleast 3 coats of clear acyrlicprimer . All surfaces are to be brushed with nylon brushes or sand paper before application. |
