|
| 1 | CIVIL WORKS |
| 2 | \"Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.(A) Upto a depth of 2.00 m below the existing G.L.a) In ordinary soil\" |
| 3 | \"Providing brick soling in foundation and under floorwith stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labourand materials and if necessary dewatering, complete.(a).Brick on flat soling.\" |
| 4 | Plain cement concrete works with coarse aggregate, of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed andspecified including dewatering if necessary, and curing complete(Shuttering where necesary shall be measured and paid separately) (a) In prop 1cement: 3 sand :6 coarse aggregate by volume |
| 5 | \"Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.\" |
| 6 | \"Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using mixture machineA)In sub - structure up to plinth levelb) M20 or Prop. 1:11/2:3\" |
| 7 | \"Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.b) M20 or Prop. 1:1.5:3\" |
| 8 | \"Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.ii) Using 25mm thick plank\" |
| 9 | \"Columns, Pillars, Posts & Struta) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical faceii) Using 25mm thick plank\" |
| 10 | \"Sides of tie beams, grade beams etc. at or below ground level.Ii) Using 25mm thick plank\" |
| 11 | \"Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.A) For depth not exceeding 1.0M.i) Using 38mm thick plank\" |
| 12 | \"Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). (ii)Super Ductile (SD) TMT reinforcement bars(i) TATA/SAIL \" |
| 13 | \"Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level.(c). In proportion 1:5.\" |
| 14 | \"Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.\" |
| 15 | \"Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.\" |
| 16 | \"1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paidseparately)(A) 112mm thick brick wall(a) In cement mortar in proportion 1:4. (1 cement:4 sand)\" |
| 17 | \"Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a)With sal wood\" |
| 18 | \"Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. b) Non decorative type and block board core.(i) 40 mm thick .\" |
| 19 | \"Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels.(a)2 Track sliding window(iv) 5 mm clear glass\" |
| 20 | \"Providing, fitting and fixingM.S.grillof required pattern for windows/ clerestory windows/ openingwith M.S. flatsat required spacingin frame all round,squre or round M.S.bars with round headed bolts and nuts or screws.II.Ornamental grillc)Fixed toBrickwork,etc.\" |
| 21 | \"Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed.a) TATA make Circular Hollow section- CHS of Grade YST-310 conforming to I.S. Specification : 1161-1998 \" |
| 22 | \"Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing)at all levels including fitting and fixing self drilling, self tapping screws complete complete.TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement(e) 0.80mm thick \" |
| 23 | \"Providing galvd iron ridging of TATA SHAKTEE / SAILincluding supplying and fixing necessary galvd screws/washers etc. complete as directed.(ii) 230 mm lapping\" |
| 24 | 15 mm thick Cement plaster in single coat on single or half brickwall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. |
| 25 | \"B) On rough sideb) In cement mortar 1:4\" |
| 26 | \"A) On fair sideb) In cement mortar 1:4\" |
| 27 | Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete. |
| 28 | Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base ofcement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed.(Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) |
| 29 | \"Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department).i) Of size300mmx450mm and above \" |
| 30 | \"Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)(i) Thickness = 1.5 mm thick\" |
| 31 | a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth. . |
| 32 | \"Wall painting (two coats) with Plastic emulsion paint of approvedbrand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.(a).Plastic Emulsion Paint of approvedbrand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)\" . |
| 33 | Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem \"Rakshak\" brand of required shade by thinning 1ltr. of paint with 750ml of waterto give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department. |
| 34 | \"Applying priming coat over newwood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughlycleaningoil, grease, dirt snd other foreign matter , sand papering and knotting. (a). With ready mixed paint , Wood primer (pink)\" |
| 35 | \"Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.b). High gloss(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).\" |
| 36 | \"Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper.a). With ready mixed \"\"red-lead/ red oxide\"\" primer.\" |
| 37 | \"Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.b). High gloss(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).\" |
| 38 | 65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed. |
| 39 | Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish. |
| 40 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) |
| 41 | \"a. Sliding door bolt(i) 300 x 16 mm\" |
| 42 | \"b. Tower bolt(ii) 250 x 12 mm\" |
| 43 | (iv) 150 x 10 mm |
| 44 | \"c. Door handles(iii)150 mm\" |
| 45 | (ii)100 mm |
| 46 | \"Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) pre-coated G.I. angle size 24mmx24mmx80mm thick fixed to the brick wall/ partition at the perimeter of ceiling with nylon sleeves and screws, at 610mm c/c. Then suspending main \"T\" section (bottom pre-coated) size 24mmx38mmx0.70mm and 3600mm long from the soffit in one direction with the help of metal Rawl Plug. Soffit cleat and G.I. Rod 4mm diameter with galvanised level clip 1220mm c/c G.I. cross BPB Grid ceiling system with Fabric Based Sound absorb Panel (595mmx595mm).\" . |
| 47 | Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre CementBoard as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. |
| 48 | \"Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified.(b) Other than Guwahati city\" |
| 49 | SANITARY |
| 50 | \"Supplying fitting and fixing G.I. pipes of following sizes, with all necessary R brand or similar approved G.I. fittings such as bend,tee,elbow,H.W. clamps etc. complete at all levels including below G.L. as directed and specified.(A) Exposed on wallsd) 25 mm dia. (medium)i) using Tata make\" |
| 51 | \"e) 20 mm dia. (medium)i) using Tata make\" |
| 52 | \"Supplying fitting and fixing C.P.bib cock 15mm dia of approved brand as directed and specified. (Pipings will be measured separately)(IV) Agmeco brand(ii) Bib cock with flange\" |
| 53 | \"Supplying fitting and fixing stop cockof approved brand and sizes as mentioned below as directed and specified. (Pipings will be measured separately)(I) Brass stop cock (heavy of Sant make)(i) 15 mm dia.\" |
| 54 | \"Proving, fitting and fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including paiting the fittings, cutting & making good the walls wherever required. (Sink cock, stop cock, watse coupling are to be paid separately)(A) Parryware Make(V) Single Bowl (210 x 180) Flat Edge - Glossy (Cat.no. C8543)\" |
| 55 | \"Providing, fitting and fixing chrome plated sink cock of approved brand as directed and specified. (G.I. & C.P. pipes will be measured and paid separately)(i) Sona brand(b) Sink cock J spout\" |
| 56 | \"Providing, fitting and fixing C.P. bottle trap complete as directed and specified.(b) Sona make(i) Bottle trap Indian 32mm\" |
| 57 | \"Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)A) Parryware makea) (i) White(iii) Universal Closet P Trap (Cat No.C0272) (inclusive of seat cover)\" |
| 58 | \"Supplying, fitting and fixing H.C.I. bend with door including bolts and nuts and other fittings as required complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trench(ii) 100mm dia.\" |
| 59 | \"Supplying, fitting and fixing H.C.I. plain single equal junction / plain tee including bolts and nuts and other fittings as required complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trench(ii) 100mm dia.\" |
| 60 | \"Supplying, fitting and fixing PVC pipes of 6 Kg./cm2 (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trench |
| 61 | (i) 160mm dia. |
| 62 | (ii) 110mm dia. |
| 63 | (iii) 75mm dia. |
| 64 | \"Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. \" |
| 65 | (ii) 110mm dia. |
| 66 | (iv) 75 mm dia. |
| 67 | Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. in exposed surface or trencesas necessary complete at all levels including below G.L. as directed and specified. |
| 68 | (a) 110 mm |
| 69 | (b) 75 mm |
| 70 | \"Supplying,fitting and fixing 87.5o PVC bend of (Supreme/Prince) or other ISI approved including joining, fiting and fixing as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trench\" |
| 71 | (i) 110mm dia. |
| 72 | (ii) 75mm dia. |
| 73 | \"Providing, fitting and fixing C.I. grating to the floors complete as directed and specified.(b) 75mm dia.\" |
| 74 | Providing vitreous Chinawash basinwith CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) |
| 75 | \" PEDESTAL BASIN (with pedestal)(A) Parryware Make(a) White(vi) Sutlej 580 x 450(Cat. No.C0473/449/C0314)\" |
| 76 | \"Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. SONA make(a)Light type(b) Heavy type\" |
| 77 | \"Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified.(c) Cera make (i) Waste coupling (full thread) 40 mm(cat.No.CA 103)\" |
| 78 | \"Providing fitting and fixing Glass Shelf complete as directed and specified.Glass shelf with C.P. guard rail(ii) Sona make (Cat. No.TR-0701)(a) 450mm\" |
| 79 | Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed. |
| 80 | Providing fitting and fixing 50mm dia. HCI cowel with cement caulking complete as directed and specified.(iv) 75mm dia. |
| 81 | \"Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Makeas specified and directed.c) 25 mm dia.\" |
| 82 | Supplying and fitting ball valve as specified and directed. |
| 83 | a) 25 mm dia. (gun metal) |
| 84 | b) 20mm dia. (gun metal/Copper) |
| 85 | \"Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed A) G.I. pipe with GI fittings a) TATA / SAIL (Medium) |
| 86 | iii) 25mm diameter |
| 87 | 125 mm diameter |
| 88 | SEPTIC TANK |
| 89 | \"Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.(A) Up to a depth of 2.00m below the existing ground level.(a) In ordinary soil\" |
| 90 | \"Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(a) In prop 1cement: 3 sand :6 coarse aggregate by volume\" e |
| 91 | \"Brick work in cement morter with 1st class brick including racking out jointsand curing complete as directed.(b) In proportion 1:4.\" |
| 92 | \"Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine(A) In substructure up to plinth levelb) M20 grade concrete or Prop. 1:1.5:3\" |
| 93 | \"Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.(a) Using 38mm thick plank\" |
| 94 | \"Cement concrete works in topping 1:1:2 (1cement :1sand :2 graded aggregates on R.C.C floor, tread and rise of steps finished with a floating coat of neat cement using cement slurry for bond @ 2.75 kg.of cement per sq. m. of floor to be laid in panelsincluding curing complete as directed.(b) 20 mm thick \" |
| 95 | \"20 mm thick Cement plaster in two coats on single or half brickwalls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. A) On rough side (backing coat 15 mm and finishing coat 5mm thick)b) In cement mortar 1:4\" |
| 96 | \"Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL(i) TMT Corrosion resistant steel (CRS) reiforcement bar \" |
| 97 | \"Providing soling in foundation and under floorwith stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labourand materials and if necessary dewatering, complete.(a).Brick on flat soling.\" |
| 98 | STAGGING |
| 99 | \"Steel work riveted and/ or bolted/ riveted in built up sections, frame work including cutting, hoisting, fixing in position and applying a priming coat of red- lead paint up to 4.6m height above plinth including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In trusses and trussed purlins up to 25m span and 15.0m overall height.\" |
| 100 | DEEP TUBE WELL |
| 101 | \"Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department.iv) Bore hole of 150mm diameter\" |
| 102 | \"Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department.PVC PIPE SUPREME /PRINCE / FUSION /SFMC Brandvi) 140mm diameter\" |
| 103 | \"Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed.B) PVC PIPESUPREME / PRINCE / FUSION /SFMC Brandvii) 110mm diameter\" |
| 104 | Supplyingfitting and fixing ISI approved PVC filter 3.00 metre long. |
| 105 | Supplyingfitting and fixing check valve (non return valve) including thread to pipes. |
| 106 | Flushing, clearing, washing and watering of the tube well |
| 107 | Single phase submersible motor pump set(Texmo/Crompton reaves/Aquatic/CRI/V-Guar suitable for 100mm bore well and above. 1HP stage 5to 18 with control panel |
| 108 | WATER TANK |
| 109 | \"Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes2000 Lt capacity(a)Sintex make\" |
| 110 | ELECTRICAL |
| 111 | Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete |
| 112 | (a) Short point upto 3.00 mtr. |
| 113 | (b) Medium point upto 6.00 mtr. |
| 114 | (c ) Long point upto 10.00 mtr. |
| 115 | Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. |
| 116 | Short point up to 3.00 metre. length. |
| 117 | Medium point up to 6.00 metre. Length. |
| 118 | Long point up to 10.00 metre. Length. |
| 119 | Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. |
| 120 | With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. |
| 121 | Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) earthing the 3rd pin of the socket as required on the switch board in surface/ recessed P.V.C. conduit wiring system. When fitted on same board of light and fan. |
| 122 | Supplying and fixing of polished Brass Bracket of 18 S.W.G, 25 cm long cast back plate and brass lamp holder complete including connection as approved by the Deptt.)as required Without Lamp |
| 123 | Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt . |
| 124 | Supplying with fitting and fixing of CFL/Fluorescent luminiuries with all accessories such as ballast, starter, etc directly on wall/ ceiling included connection as approved by deptt. With 1.5 sqmm PVC insulated S.C copper conductor as required and as directed by deptt. Striplite luminaries complete with VPIT copper ballast and 1 x 18/20 watt fluorscent tube(CG make) |
| 125 | Supplying and fixing 18 swg sheet metal boxes of the following sizesin surface wiring system with suitable size of 3mm thickness phenolic laminated sheet cover on the front face of the boxes including painting etc .as required and specified by the department. |
| 126 | 100mm x 100mm x 60mm deep |
| 127 | 100mm x150mm x 60mm deep |
| 128 | 200mm x 150mm x60mm deep |
| 129 | Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt. |
| 130 | Supply, fitting & fixing 20 mmx3 mm Copper strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of Brass Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode copper strips and Lightning Arrestor etc. as specified and directed by the deptt. |
| 131 | Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hagermake) |
| 132 | 4 way TPN (8+12)double door |
| 133 | 8 way TPN (8+24)double door |
| 134 | Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. |
| 135 | B series (6A -32A), Schneizer, MG, Legarnd, Hager make |
| 136 | 8 way SPN double door |
| 137 | Supplying including fitting fixing of followingA.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. |
| 138 | Premium model 1050 mm Sweep (ORIENT PSPOmake) |
| 139 | Supplying including fitting fixing of followingA.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (CROMPTON /ORIENT/Havells/USHA or equivalentmake) |
| 140 | Supplying and fixing of bulk head fitting suitablefor CFL lamp complete with all accessories including 20 watts CFL lamp and connection as approved by the Deptt.)as required. |
| 141 | Supplying including fitting fixing of followingA.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.(CROMPTON /ORIENT/Havells/USHA or equivalentmake)SDX 120 with metal body metal blade400 mm sweep |
| 142 | Supplying including fitting fixing of followingA.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Heavy Duty 450 mm sweep 900 RPM Single phase (ORIENTmake) |
