|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but notbacking), removing serviceable tiles and rubbish off the premises complete all as directed. |
| 2 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed. |
| 3 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed. |
| 4 | Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed. |
| 5 | Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed. |
| 6 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed. |
| 7 | Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 8 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed. |
| 9 | Taking down shutters of any description exc 1 sq. m and not exc 2 sq. m each .complete all as specified and directed. |
| 10 | Taking down shutters of any description n.exc 1 sq. m complete all as specified and directed. |
| 11 | Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed. |
| 12 | Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed. |
| 13 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sq. Mcomplete all as directed. |
| 14 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed. |
| 15 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position complete all as directed. |
| 16 | Materials and Labour for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding, complete all as specified and directed. |
| 17 | Materials and Labour for 100 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding, complete all as specified and directed. |
| 18 | M&L for cement concrete 25mm thick type B-0, 1:2:4 (12.5 mm graded aggregate) asflooring, finished even and smoothall complete as specified and as directed |
| 19 | M&L for cement concrete 40 mm thick type B-0, 1:2:4 (12.5 mm graded aggregate) asflooring, finished even and smoothall complete as specified and as directed |
| 20 | Materials and Labour for plain cement concrete (1:3:6) Type C-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed. |
| 21 | M&L Precast cement concrete 1:11/2:3, type A1 (Using 20 mm graded granite stone aggregate) in landings, slabs cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed |
| 22 | M & L for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge. |
| 23 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M35 grade conforming to IS 15658-2006 made by block making machine with strong vibratory compaction, of approved size, design & shape, cast in rubber mould, glossy finish of approved colour, laid in required colour and pattern over and including 30 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. |
| 24 | Materials and Labour for, DigitalNon - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, in riser of steps, skirting, dado and pillar laid over cement screed baseincluding 15 thick rendering Cement mortar (1:3) complete all as specified and directed |
| 25 | Materials and Labour for, DigitalNon - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed. |
| 26 | Materials and Labour for, Digital glazed ceramic coloured tiles, 450 X 300 X 7mmthick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados,skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed. |
| 27 | Material and Labour for Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M,on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.MAKE:-(Johnson/Kajaria or equivalent make ) |
| 28 | Materials and Labour for,Digital Vitrified Ceramic Tiles, , 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to matchover and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:-(Johnson/Kajaria or equivalent make ) |
| 29 | M&L for Prepolished glossy finishchequered cement concrete tiles chemically treated size 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigments over 20 mm thick cement mortar 1:6 bedding layer in floors fixed complete all as specified and directed. |
| 30 | Materials and Labour for brick work with fly ash old size bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed. |
| 31 | Cutting holes in brick walls exc half brick but not exc one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required (Depth of embedded portion measured from the face of the jamb into the wall)all as specified and directed . |
| 32 | Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded,including making good disturbed surfaces as per existing specfication complete all as specified and directed. |
| 33 | Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed. |
| 34 | Supply and Fix,steel ventilator with top hung shutter including hinges, steel pegstay, complete with glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed. |
| 35 | Supply and Fix,steel ventilator with top hung shutter including hinges, steel pegstay, complete without glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed. |
| 36 | Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend toshape required including cranking, bending spirally for hopping for columns,hooking ends and binding with and including mild steel wire (annealed) not lessthan 0.9 mm dia. or securing with clips complete all as specified and directed |
| 37 | Supply and Fix, in repair 25 mm dia. mild steelconduit ,wall thickness 1.00 mm, overall PVC coated including suitable fixing brackets and fancy type end caps as in darpary rod for doors/ windows, complete all as specified and directed. |
| 38 | Materials and Labour Pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified and fixed of size 105x60 mm complete all as specified and directed. |
| 39 | Materials and Labour Pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified and fixed of size 125x60 mm complete all as specified and directed. |
| 40 | M & L for 35 mm thick, timber species of super group and durability class I as per IS 12896: 1990 and first grade as per IS 1003 (Part-1): 2003, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, wire gauze, etc. (without sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-Charge. |
| 41 | Materials and Labour for 2nd class hard wood 35mm thick factory made shutters plain, framed, panelled (two panel )with lock rail and panel of 09 mm BWP commercial ply or12mm thick venerred particle board with commercial veenering on both faces. The size of rail and style as per IS-1003(part-1), klin seasoned and chemically pressure treated complete all as specified and directed. |
| 42 | M&L for medium density fibre board 18mm , exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work or steel frame incl necessary beeding complete all as specified and directed. |
| 43 | M&L for medium density fibre board 12mm exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 44 | S & F plain fillets of 2nd class hard wood in square, rectangular or triangular in section wrought secured with screw, area exceeding 3 sqcm but not exceeding 6 sqcm complete all as specified and directed. |
| 45 | S&F Steel rolling shutters(thickness of laths 1.25 mm) with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type incl taking down existing unserviceable complete all as specified and directed by engineer-in-charge. |
| 46 | M & L for frame work consisting sections made of mild steel sheet galvanised with zinc coating of grade 120 gram per sqm as per IS 277 as per IS 277: 2003 and the sections of perimeter channel of size 20 mm (flange) X 27 mm (web) X 30 mm (flange) X 0.50 mm (thickness), intermediate channel of size 15 mm (flange) X 45 mm (web) X 15 mm (flange) X 0.80 mm (thickness), ceiling section 80 mm (total width) X 26 mm (flange) X 51 mm (web) X 0.50 mm (thickness), angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, angle hangers of size 25 mm X 10 mm X 0.50 mm and of required length, mild steel galvanised with zinc coating dash fastener of size 12.5 mm dia x 50 mm long and connecting clip made out of 2.64 mm dia x 230 mm long galvanised mild steel wire, fixing perimeter channel on the wall along the perimeter of ceiling using nylon sleeves wall plug at 450 mm centre to centre spacing, hanging intermediate channel at 900 mm centres to centre spacing with soffit of ceiling using rawl plug, dash fastener, angle cleat, angle hangers at 900 mm centre to centre spacing, fixing ceiling section to the intermediate channel transversely at 450 mm centres to centre spacing using connecting clip at every junction with and including gypsum wallboard, 12.5 mm thick as per IS 2095 (Part 1): 2011, tapered edge, fixing to ceiling section and perimeter channel using dry wall screws of size 3.5 mm X 25 mm at 230 mm c/c including jointing and finishing to a flush finish of tapered edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint complete all as specified and as directed. |
| 47 | Supply and Fix, solid PVC door frame of size 50 mm X 47 mm made out of 5 mm Prelam PVC sheet reinforced with MS square tube, fixed in opening all as specified and directed. |
| 48 | Supply and Fix, factory made solid panelPrelam PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed. |
| 49 | Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 100 mm sizecomplete all as specified and directed |
| 50 | Supply and Fix,IS marked Stainless steel butt hinges, medium weight, cold rolled 75 mm sizecomplete all as specified and directed |
| 51 | S & F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy to door shutter complete all as specified and directed |
| 52 | Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed. |
| 53 | S & F 150mm long Stainless steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed. |
| 54 | S & F 200mm long Stainless steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed. |
| 55 | Supply and Fix, aluminium handles, Fabricated type, anodized, 150 mm size, complete all as specified and directed. |
| 56 | S & F 100mm stainlesssteel presseddesigner handles, oval type, stove enamelled black complete all as specified and directed. |
| 57 | Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed. |
| 58 | Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil puttyin squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) fromframe including providing wooden beads painted with two coat of enamel paint over a coat of primercomplete all as specified anddirected. |
| 59 | S & F of figured glass, pin head type 4mm thick in squares n.exc 0.50 Sqm in each pane complete all as specified and as directed. |
| 60 | Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed. |
| 61 | S&F for framed work (Fe 410-W (Gde-E-250) quality as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing with and including dismantling of existing unserviceable complete all as specified and directed. |
| 62 | S & F300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 63 | S & Fin repair300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 64 | Supply and Fix,stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 65 | Supply and Fix in repair,stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 66 | Materials and Labour for 100 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement and laid in panels including joints filled with sealing compound grade A complete all as specified and directed. |
| 67 | M&L for double wall corrugated HDPE (PE-100) pipes 600mm dia, class NP6, ISI marked with smooth internal and corrugated (profiled) external surface with anti rodent property, conforming to IS-16098 (Pt-II), laid in trenches including all joints & necessary jointing material like mechanical connector i.e. thread/insert joint/quick release coupler/compression fitting joint/ or flanged joint etc. complete all as specified and as directed. |
| 68 | Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed. |
| 69 | Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 20 mm bore, complete all as specified and directed. |
| 70 | Materials and Labour for galvanized steel tubing, medium grade, 15 mm borewith all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed. |
| 71 | Materials and Labour for galvanized steel tubing, medium grade, 20 mm borewith all fittings and fixed complete to walls and ceiling or laid in floor, complete allas specified and directed. |
| 72 | Supply and Fix, in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring andwith overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed. |
| 73 | S&F 500 ltrsIS markedmultilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position withand including 20mm PTMT ballvalves high pressure with polythene float and nut with and including dismantling exsiting one complete all as specified and directed . |
| 74 | S&F 1000 ltrsIS markedmultilayer rotational moulded polythytene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position withand including 25mm PTMT ballvalves high pressure with polythene float and nut with and including dismantling exsiting one complete all as specified and directed . |
| 75 | M&L for preparation of new or previously undecorated wooden surface of any description, not otherwise describedover 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of pink primer complete all as specified and as directed. |
| 76 | Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed. |
| 77 | Material and labour for plastering 5 mm thick on fair faces of brick work or concrete surfaces (on ceiling surfaces) in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed. |
| 78 | Materials and Labour for rendering 15 mm thick, cement plaster, in cementmortar (1:6) on surfacefair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified anddirected. |
| 79 | Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed.Note: - (Water proofing compound will be measured and paid separately) |
| 80 | Rendering dubbing coat over damaged irregular surface of chajjas roof projections ceiling facia etc average 15mm thick in cm 1:4 over cement slurry coat thick @ 3 Kg/sqm making the surface even followed by 5mm thick rendering in CM 1:3 furnished even& smooth incl making of drip course as reqd completeincl roughening surface of old concrete by picking sweeping clean and washing with water with and including two coat of damp proof ultranot less than 1.5mm thick as per manufactrur,s instruction with and including primer complete all as specified.Note :-Rate for form work if reqd to be incl in the rate quoated by the contractor. |
| 81 | Supply only Liquidwater proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed (Make : CICO No- 1/SIKA/ACCO PROOF). |
| 82 | M&L for preparation of old distempered surfaces of walls including cornices, pilasters and other wall features etc by washing, rubbing down and stopping and applying one coat acrylic distemper on old surfaces complete all as specified and as directed.complete all as specified and directed Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty) |
| 83 | Preparation of newly plastered surfaces on ceilings and applying three coats of white wash complete all as specified and as directed. |
| 84 | Material and Labour for applying two coats of cement-based paint, white or tintedto new plastered surfaces on walls including priming with alkali resistantpriming paint and including preparation of surfaces complete all as specified and directed. |
| 85 | Removal of unserviceable material obtained from demolition to a distance of exc 1000m but n. exc 2000mbeyond the lead included in the rates, including loading, unloading and stacking at the out side MOD land Complete all as directed , |
