| 1 | 1 | Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level. | | 1 | Cum |
|---|
| 2 | 2 | Dismantling of plain or corrugated steel/asbestos sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. | | 550 | Sqm |
|---|
| 3 | 3 | Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified . | | 300 | Sqm |
|---|
| 4 | 4 | Dismantling structural steel work including doors, gates but excluding framed truss etc | | 1 | Qtl |
|---|
| 5 | 5 | Dismantling floor hearth or wall tiling including cement mortar bedding but not backing. | | 751 | Sqm |
|---|
| 6 | 6 | Taking down chowkhat or frame with shutter without taking off shutters from the frame, size of shutter not exceeding 1.5 Sqm each complete all as specified and directed. | | 30 | Each |
|---|
| 7 | 7 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each. | | 10 | Each |
|---|
| 8 | 8 | S&F for 0.63mm galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed. | | 150 | Sqm |
|---|
| 9 | 9 | S & F 0.80mm thick plain galvanized Mild steel sheeting, class-VIII having minimum zinc coating of 120 gm per Square metre as in ridge, valley gutter complete all as specified and directed. | | 15 | Sqm |
|---|
| 10 | 10 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified | | 350 | Sqm |
|---|
| 11 | 11 | S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. | | 35 | Sqm |
|---|
| 12 | 12 | S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified. | | 250 | Sqm |
|---|
| 13 | 13 | S & F in repair for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed with aluminium/GI grid/section complete all as specified. | | 50 | Sqm |
|---|
| 14 | 14 | M&L framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel \ndoor fittings (exclusive of steel Framed work as in doors orgates of angle or other section with gusset plates, rails.braces, etc., complete, drilled forfi xing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging S&F door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete | | 100 | Kg |
|---|
| 15 | 15 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/coloured cement to match all as specified. | | 50 | Sqm |
|---|
| 16 | 16 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick exc 0.11 Sqm but n exc 0.18 Sqm set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/coloured cement to match all as specified. | | 200 | Sqm |
|---|
| 17 | 17 | All as per item No 16 above here-in-before but in skirting. | | 20 | Sqm |
|---|
| 18 | 18 | M&L for ceramic coloured printed tiles of size 300x200mmx7 mm thick, on verticals surfaces, set and jointed in neat cement slurry and pointed in coloured. | | 100 | Sqm |
|---|
| 19 | 19 | M&L for coloured glazed ceramic tiles in vertical surface 300mmX450mmx 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed. | | 70 | Sqm |
|---|
| 20 | 20 | M&L for non - skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/coloured cement to match all as specified. | | 330 | Sqm |
|---|
| 21 | 21 | All as per item No 20 above here-in-before but in skirting. | | 31 | Sqm |
|---|
| 22 | 22 | M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces to received vertical tiles complete all as specified and directed. | | 221 | Sqm |
|---|
| 23 | 23 | M&L for 40 mm thk PCC 1:2:4 type B-1 using20mm graded agg as in flooring finished even and smooth with using extra cement complete all as specified and directed. | | 40 | Sqm |
|---|
| 24 | 24 | M&L 75 mm thick cement concrete type C2 1:3:6 (40 mm graded aggregate) as in plinth protection, using extra cement for finishing. | | 150 | Sqm |
|---|
| 25 | 25 | M & L for PCC (1:3:6) type C-2 using 20mm graded aggregate as in coping including necessary form work all as specified and directed | | 0.25 | Cum |
|---|
| 26 | 26 | Demolition of brick work including all quoins arches pillars etc built in cement mortar. | | 7.175 | Cum |
|---|
| 27 | 27 | M&L for brick work in cement mortar (1:4) using sub class 'B' bricks straight or curved on plan exc 6.0 m mean raidus | | 2 | Cum |
|---|
| 28 | 28 | M&L for brick work with sub class 'B' bricks straight or curved on plan in any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed | | 45 | Sqm |
|---|
| 29 | 29 | Taking down cement plaster on walls built in cement mortar etc including racking out joints, hacking for key, scrubbing down with water etc. | | 200 | Sqm |
|---|
| 30 | 30 | M&L for 15mm thick cement plastering in cement mortar 1:6 brick or concrete surfaces of wall finished fair and even complete all as specified and directed. | | 130 | Sqm |
|---|
| 31 | 31 | M&L for 15mm thick cement plastering in cement mortar 1:4 brick or concrete surfaces of wall finished fair and even with out using extra cement complete all as specified and directed. | | 170 | Sqm |
|---|
| 32 | 32 | M&L for 5mm thick cement plastering in cement mortar 1:3 ceiling surfaces finished fair and even,complete all as specified and directed. | | 30 | Sqm |
|---|
| 33 | 33 | Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,including one shop coat of primer complete as specified, supplied and fixed | | 50 | RM |
|---|
| 34 | 34 | S&F factory made 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative choice sunmica lamination 0.9mm thick type I with lipping to match fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. | | 9 | Sqm |
|---|
| 35 | 35 | S&F for second class hardwood 35 mm thick plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated. | | 9 | Sqm |
|---|
| 36 | 36 | S&F for second class hardwood glazed and skeleton door shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats. | | 9 | Sqm |
|---|
| 37 | 37 | S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening. | | 45 | Rm |
|---|
| 38 | 38 | S&F for Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame wedded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site. | | 14 | Sqm |
|---|
| 39 | 39 | S&F anodised aluminium powder coated any colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified | | 49 | Kg |
|---|
| 40 | 40 | S&F for anodised aluminium powder coated any colour window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. | | 11 | Sqm |
|---|
| 41 | 41 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. | | 12 | sqm |
|---|
| 42 | 42 | ditto above as item no 123 but without glazing bar. | | 12 | sqm |
|---|
| 43 | 43 | Material and labour for Chimney bars (straight or camber) bearing bars; tongues or water bars for window frames, window guard bars, plain, let in and fixed independently in wooden frames L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed. | | 30 | Kg |
|---|
| 44 | 44 | S&F Sheet glass 4.8mm thick clear/sun shade colour glass, ordinary quality and glazing with oil putty in squares exceeding 0.5sqm in each pane. | | 10 | Sqm |
|---|
| 45 | 45 | S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane. | | 10 | Sqm |
|---|
| 46 | 46 | Hacking out old broken glass of any thickness size or description from wooden frames or metal frames fixed with wooden beads/ putty and providing and fixing new ones. | | 20 | Sqm |
|---|
| 47 | 47 | S&F for galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples. | | 20 | Sqm |
|---|
| 48 | 48 | S&F in repairs, galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples. | | 50 | Sqm |
|---|
| 49 | 49 | S&F for mild steel conforming to Fe 410-0 or Fe 310-0 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; hand made sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles. | | 5 | Kg |
|---|
| 50 | 50 | S&F Butt hinges, medium weight, cold rolled mild steel, 75mm size. | | 30 | Each |
|---|
| 51 | 51 | S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size. | | 30 | Each |
|---|
| 52 | 52 | S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete. | | 20 | Each |
|---|
| 53 | 53 | S&F Aluminium, anodised, barrel tower bolt 150mm long of extruded section and fixed complete. | | 20 | Each |
|---|
| 54 | 54 | S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed. | | 15 | Each |
|---|
| 55 | 55 | S&F Extruded aluminum alloy handles, fabricated type, anodised 100 mm size. | | 20 | Each |
|---|
| 56 | 56 | S&F Extruded aluminum alloy handles, fabricated type, anodised 150 mm size. | | 30 | Each |
|---|
| 57 | 57 | M&L for preparation of new plastered surfaces of walls and applying two coat of oil bond distemper over a coat of primer all as specified. | | 35 | Sqm |
|---|
| 58 | 58 | S&F in repair floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor | | 15 | Each |
|---|
| 59 | 59 | M&L for preparation of old surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint in any tint complete all as specified & directed. | | 1500 | Sqm |
|---|
| 60 | 60 | All as per item 59 above but two coat. | | 50 | Sqm |
|---|
| 61 | 61 | M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint in any tint all as specified and directed | | 150 | Sqm |
|---|
| 62 | 62 | All as per item 61 above but one coat. | | 1500 | Sqm |
|---|
| 63 | 63 | M&L for two coats of synthetic enamel paints over a coats of red oxide primer including prepration of new steel surfaces of any description over 10 cm in width or girth not otherwise described | | 25 | Sqm |
|---|
| 64 | 64 | M&L for preparation of untreated new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed. | | 60 | Sqm |
|---|
| 65 | 65 | M&L for Preparation of old decorated surfaces and appplying one coat of white wash on walls, cornices etc. complete all as specified and directed. | | 500 | Sqm |
|---|
| 66 | 66 | All as per item No-65 above but two coat of white wash. | | 600 | Sqm |
|---|
| 67 | 67 | All as per item No. 65 above but on ceiling. | | 1000 | Sqm |
|---|
| 68 | 68 | Complete removal of existing treatment of walls and preparation of old surfaces of wall including scrapping down, smoke soot, efflorescent salts trading oil and greasy spots etc applying two coats of cement base paint over a coat of chalk whitening/primer complete all as specified and as directed. | | 200 | Sqm |
|---|
| 69 | 69 | All as per item No 68 here-in-before but one coat of cement base paint on wall. | | 2000 | Sqm |
|---|
| 70 | 70 | M&L for complete removal of existing treatment of wall and applying two coats of exterior emulsion paint (weather coat) over a coat of approved primer complete all as specified and directed. | | 20 | Sqm |
|---|
| 71 | 71 | All as per item No 70 here-in-before but one coat of exterior emulsion paint (weather coat) on old surface. | | 30 | Sqm |
|---|
| 72 | 72 | M&L for Preparation of old decorated surfaces by washing, scrubbing down, and applying one coat of oil bound distemper on walls.all as specified and directed | | 6000 | Sqm |
|---|
| 73 | 73 | M&L for complete removal of existing treatment of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed. | | 1000 | Sqm |
|---|
| 74 | 74 | M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of 3mm thick wall care putty filling complete all as specified and directed. | | 200 | Sqm |
|---|
| 75 | 75 | M&L for preparation new surface of wall and applying two coats of distemper oil bound over a coat of 3mm thick wall care putty filling complete all as specified and directed. | | 80 | Sqm |
|---|
| 76 | 76 | Preparation of new plastered surfaces of walls and applying three coat wash complete all as specified and directed. | | 50 | Each |
|---|
| 77 | 77 | M&L for Preparation of new surfaces and appplying twos coat of white wash on ceiling, cornices etc. complete all as specified and directed. | | 30 | Sqm |
|---|
| 78 | 78 | M&L preparation of new surfaces & applying two coats cement base paint over a coat of primer complete all as specified and directed. | | 170 | Sqm |
|---|
| 79 | 79 | S&F in repair 15mm bore bib cock chromium plated fancy type, screwed down, screwed for iron pipe or for brass ferrule. | | 25 | Each |
|---|
| 80 | 80 | S&F in repair 15mm dia pillar tap cast copper alloy chromium plated fancy type (ISI Marked) | | 5 | Each |
|---|
| 81 | 81 | S&F GI pipe medium grade 15 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes. | | 50 | RM |
|---|
| 82 | 82 | S&F GI pipe medium grade 20 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes. | | 10 | RM |
|---|
| 83 | 83 | S&F brass chromium plated angle cock 15mm bore with crutch or butterfly handle screwed to iron pipe, fixed in repair. | | 12 | Each |
|---|
| 84 | 84 | S&F CP towel rail 600mm long with brackets, chromium plated 20mm dia in repair | | 5 | Each |
|---|
| 85 | 85 | S&F brass CP shower rose 100mm size with swivel joint fixed in repairs. | | 5 | Each |
|---|
| 86 | 86 | S&F PVC low level flushing cistern of 10 ltrs capacity incl flush pipe complete fixed in repairs. | | 11 | Each |
|---|
| 87 | 87 | S&F Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe and fixed in repair. | | 4 | Each |
|---|
| 88 | 88 | S&F in repair Soap dish ,vitreous china white, approximate size-160x160x90 mm, fixed with chromium plated brass screw. | | 6 | Each |
|---|
| 89 | 89 | S&F in repair vitreous china wash down water closet (pedestal pattern) with plastic seat cover including PVC low level flushing cistern 10 ltrs capacity complete as directed by Engr-in-Charge. | | 5 | Each |
|---|
| 90 | 90 | M&L for vitreous china squatting pan, Orissa, pattern size 580 x 440 mm white with integral foot rests(excluding flushing cistern and flush pipe)including connection to trap and to flushing pipe, anti-syphonage pipe etc complete including making good to floor complete all as per specified and directed. | | 7 | Each |
|---|
| 91 | 91 | S&F mirror of size 450x600x5mm thick with aluminium frame and mounted on 6mm ply confirming to IS, with two Nos of hanging hooks fixed in repairs. | | 5 | Each |
|---|
| 92 | 92 | S&F in repair PVC connection pipe 15mm bore 450mm long. | | 25 | Each |
|---|
| 93 | 93 | S&F waste pipe 750 long for WHB or sink in repairs. | | 30 | Each |
|---|
| 94 | 94 | S&F in repair vitreous china white wash hand basin flat back size 550x400mm. | | 4 | Each |
|---|
| 95 | 95 | S&F CP grating 100mm dia with waste hole. | | 20 | Each |
|---|
| 96 | 96 | S&F CP Health faucet for WC. | | 6 | Nos |
|---|
| 97 | 97 | S&F in repair EWC sheet cover white colour. (Make : Hindware/Parryware/Cera). | | 10 | Each |
|---|
| 98 | 98 | Demolition of cement concrete (unreinforced) of any description and in any position including taking out water closet Indian type/ EWC and removal of lime concrete bed, 'P' or 'S' trap and cleaning the sunken portion complete all as directed. | | 2 | cum |
|---|
| 99 | 99 | M&L Water proofing treatment on RCC roof etc. comprising with the following operations and as specified herein below :- (a) Taking down/scrapping out existing old tarfelt bituminous compound including, sweeping, cleaning, washing down to remove dust etc and removing debris to a distance n.exc. 250m. (b) 15 mm thick plastering in cement mortar 1:4 mixed with WPC @ 3% by weight of cement finished even & smooth and curing for minimum 7 days. (c) Preparing & cleaning of fully dried cement plastered surface (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per Sqm conforming IS-3384 - 1986 (e) A layer of APP based polymeric membrane 3mm thick (minimum), weighing 3.5 kg per Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm )shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm on longitudinal direction. | | 150 | Sqm |
|---|
| 100 | 100 | M&L (a) Top of RCC slab in sunken portion including peripheral beams shall be plastered with 15mm thick ement and sand mortar (1:3) using approved water proofing compound @ rate of 3% by wt of cement and finished even and smooth with out using extra cement and curved adequately and allowed to dry. (b) Two coat of epoxy resin/polymer modified cementaticious coating like brush bond of Fosroc or equivalent both on floor or wall/beam shall be applied as per manufacturer's instruction. (c) Slab to be given 1:20 slope outwards with 25mm GI pipes spout with 300mm projection beyond outer surface of wall. (d) Water tightness by flooding for 72 hours the same shall be filled with lean concrete (1:4:8) type D2 using cinder upto required depth (lean concrete will be measured seperately). Surrounding to WC Pan shall howeverbe of lime concrete as spd and directed. (e) All stages shall be passed by GE personally. | | 50 | Sqm |
|---|
| 101 | 101 | M & L cement concrete type D-2, 1:4:8, using 40mm graded aggregate as in foundations, fillings and mass concrete. | | 16 | Cum |
|---|
| 102 | 102 | Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete/PVC pipe) set in cement mortar/concrete 75 /110 mm dia fixed in position. | | 125 | RM |
|---|
| 103 | 103 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls as specified | | 65 | RM |
|---|
| 104 | 104 | All as per item No 103 hereinbefore above but bore of pipe 75 mm dia fixed to walls. | | 10 | RM |
|---|
| 105 | 105 | S&F(SWR) 110mm bore pipe junction single (single T) equal and unequal with access door | | 10 | Each |
|---|
| 106 | 106 | S&F PVC (SWR) branch piece, double (double Y) equal or unequal 110mm bore. | | 8 | Each |
|---|
| 107 | 107 | S & F 110 mm dia PVC (SWR) vent cowl complete all specified and as directed. | | 5 | Each |
|---|
| 108 | 108 | Fixing only 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls after cleaning the old pipe all as specified and directed. | | 50 | RM |
|---|
| 109 | 109 | All as per item No111 hereinbefore above but bore of pipe 75 mm dia fixed to walls. | | 15 | RM |
|---|
| 110 | 110 | S&F PVC (SWR) bends 110mm bore of any radius with access door. | | 5 | Each |
|---|
| 111 | 111 | S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia. | | 10 | Each |
|---|
| 112 | 112 | Supply only integral water proofing compound complete all as specified and directed. | | 47 | Kg |
|---|
| 113 | 113 | S&F in repairs CP wall mixer (3 in 1) complete all as specified and direcated and as approved by GE. | | 3 | Each |
|---|
| 114 | 114 | M & L for cement concretetype C-2, 1:3:6 (40mm graded stone aggregates) as in surface channels and drains | | 3 | Cum |
|---|
| 115 | 115 | M & L for Extra forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement | | 50 | RM |
|---|
