|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq m on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in charge. All kinds of soil |
| 2 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources:8 graded stone aggregate 40 Mm nominal size derived from natural sources) |
| 5 | Treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar1:2(1 cement: 2 Coarse sand) to match the existing floor: |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : (1 cement:1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement :1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived From natural sources). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, Bessemer\"s and cantilevers |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived From natural sources). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies And access platform |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 15 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) |
| 16 | Providing & applying a coat of residual petroleum bitumen of grade ofVG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 17 | Brick work with common burnt clay F.P.S.(non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and sizes in : |
| 18 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Thermo-Mechanically Treated bars of gradeFe-500D or more. (TMT Bars) Fe-500 |
| 20 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 21 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 22 | 12 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 23 | Cement concrete flooring 1:2:4(1 cement: 2 coarse and:4 graded stone of size 12.5 mm nominal size) laid in one layer finished with floating coat of neat cement (25 mm thick floor) |
| 24 | Check red terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete,on20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : |
| 25 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) : |
| 26 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq m including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 27 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry and mixed with pigment of matching shade include in grubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab color of Black, Cherry/Ruby Red or equivalent |
| 28 | Providing and fixing factory made uPVC white color sliding glazed window up to 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to Upvc profile), appropriate dimension of uPVC extruded glazing bead sand uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame& sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of |
| 29 | Providing and fixing12 mm thick frame less toughened glass door shutter of approved brand and manufacture, including providing and fixing top &bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately). |
| 30 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 31 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 32 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 33 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to115 Mm |
| 34 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase. |
| 35 | Supply & filling of cinder in sunken portion of building including braking in to required sizes including supply of all material, T&P required size including of supply of all material , labour, T&P required for proper completion of work. |
| 36 | Providing and laying water proofing treatment in sunken portion of W.C., bathroom etc, by applying cement slurry mixed with water proofing cement compound consisting of applying :- (a)First layer of slurry of cement @ 0.488 Kg/Sqm mixed with water proofing cement compound @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with water proofing cement compound @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 37 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 38 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet,1200 mm Long spaced between main\" |
| 39 | Construction of drain along with apron (150X150MM) |
| 40 | Providing and fixing BRICK CLADDING on façade with adhesive And filing joints with grouting complete |
| 41 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron PorStrap,10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requireda) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm With integral type foot rests |
| 42 | b) Same as above but for European type W.C. pan with white plastic seat And lid. Make- Cera, Hindware. |
| 43 | Providing and fixing wash basin with C.I.brackets,15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a)White Vitreous China Flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap |
| 44 | Providing and fixing Stainless Steel AISI 304(18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good theWalls wherever required Kitchen sink with drain board of size 510x1040x200 mm |
| 45 | Providing and fixing flexible P.V.C. waste pipe for sink or washbasinIncluding PVC waste fittings complete. Flexible pipe 32 mm dia |
| 46 | Providing and fixing flexible P.V.C. waste pipe for sink or washbasinIncluding PVC waste fittings complete. Flexible pipe 40 mm dia |
| 47 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x260x350 mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requireda)One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 48 | b)Range of two urinal basins with 5 litre white P.V.C. automaticflushing cistern |
| 49 | c)Range of three urinal basins with 10 litre white P.V.C. automaticflushing cistern |
| 50 | Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4(1cement:2 coarse sand: 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade(5X4X0.6X2.1) |
| 51 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleat switch C.P. brass screws and washerscomplete. |
| 52 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube up to 1 meter long with S.S. triangular plate for Europeantype W.C. ofQuality and make as approved by engineer-in-charge.15 mm nominal bore |
| 53 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 54 | Providing and fixing CP Brass Single lever lelephonic wall mixtureof quality & make and as per the direction of Engineer-in-charge.a)15 mm nominal dia. |
| 55 | Providing and Fixing C.P. brass Ablution health faucet assemblywith1.0 m long braided PVC hose with mounting bracket fixed on wall complete.[FOR EWC]-Make-JAQUAR ALD-565 |
| 56 | Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fact of approved quality conforming to IS:8931. 15 mm nominal bore-ESSCO SQT 526AKN |
| 57 | Providing & fixing 60x2cm.C.P. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw. ESSCOAEC-1181 |
| 58 | Supplying & Fixing of CP soap tray fixed to the wall with PVCRubber plug with CP brass screws-Make-ESSCOAEC-1131 |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes,havingthermalstabilityforhot&coldwatersupplyincludingallCPVCplain&brassthreadedfittingsThisincludesjointingofpipes&fittings with one step CPVC solvent cement, trenching, refilling &testing of joints complete as per direction of Engineer in Chargea)150 mm nominal dia Pipes |
| 60 | b)100 mm nominal dia Pipes |
| 61 | c)80 mm nominal dia Pipes |
| 62 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embedded in &including cement concrete blocks 10x10x10cm. of1:2:4 mix (1 cement:2 coarse:4 graded stone aggregate 20 mm nominalsize).Including cost of cutting holes & making good the walls etc.a)for 100 mm dia pipe. |
| 63 | b)for 75 mm dia pipe. |
| 64 | Providing & fixing cast iron trap of self cleansing design with or without vent arm complete, including cost of cutting & making good theWalls & floors.a)100 mm inlet &75 mm outlet. |
| 65 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.(i)Single socket pipes.a)110 mm diameter |
| 66 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1mx1 mx 400 micron, finished with 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement, punning, rounding the edges andMaking and finishing the outlet complete.a) 110 mm |
| 67 | Providing and fixing unplasticised-PVC pipe clips of approved design tounplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing increment mortar1:4 (1cement:4 coarse sand) and making good the wall etc. complete.a) 110 mm |
| 68 | Providing and fixing to the inlet mouth of rain water pipe cast irongrating15cm diameter and weighing not less than 440 grams. |
| 69 | Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete asPer direction of Engineer in Charge.Internal work-Exposed on walla)25mm nominal dia Pipes |
| 70 | b)32mm nominal dia Pipes |
| 71 | c)40mm nominal dia Pipes |
| 72 | d)50mm nominal dia Pipes |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etca)15 mm dia nominal bore |
| 74 | b)20 mm dia nominal bore |
| 75 | Providing and fixing 45cm long unplasticised PVC connection pipeWith brass unions.a) 15 mm nominal bore |
| 76 | Providing & fixing CP brass bibcock of approved quality conformingTo IS8931a) 15 mm nominal bore |
| 77 | Providing & fixing C.P. brass long body bibcock of approved quality conforming to IS standards and weighing not less than 690 gms.a) 15 mm nominal bore |
| 78 | Providing &fixing C.P. brass angle valve for basin mixer and gyserPoints of approved quality conforming to IS8931a) 15 mm nominal bore |
| 79 | Providing and fixing gun metal gate valve with wheel of approvedquality.a)25 mm dia nominal bore |
| 80 | b)32 mm dia nominal bore |
| 81 | c)50mmdianominalbore |
| 82 | Providingand fixing ball valve (brass) of approved quality, High orLow pressure, with plastic floats completea) 20 mm nominal bore |
| 83 | b) 25 mm nominal bore |
| 84 | SUB HEAD I-WIRING POINTS |
| 85 | SUB HEAD II-INSTALLATION OF LIGHT FIXTURES AND FANS |
| 86 | SUB HEAD III-DISTIBUTION BOARD |
| 87 | SUB HEAD IV-EARTHING |
| 88 | SUB HEAD V-MAIN DISTRIBUTION BOARD AND CABLES |
| 89 | PART B-NON SCHEDULE ITEMS |
| 90 | Supply and fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work |
| 91 | Supply and fixing of fire extinguisher, ABC Type 6.00kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work |
| 92 | Supply and fixing of C02 type fire extinguisher4.5 kg. capacity each (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 93 | Supply and fixing of C02 type fire extinguisher 6.5 kg. capacity each (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 94 | Supply and fixing of fire bucket, round bottom made ofG.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported each on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge. |
| 95 | Outdoor Development of Site |
| 96 | SUPPLYING, INSTALLATION, TESTING AND COMMISSIONING OF AIR CONDITIONER 2 TON WITH STABILIZERS. BRAND O-GENERAL, DAIKIN, BLUESTAR ETC |
| 97 | Supply, Installation, Testing, Commissioning of library management software withIncluding License & Maintenance and Customization charges |
| 98 | Supply & Installation of Laser Jet MFP Printer with Scanner |
| 99 | Supplying, Installation, Testing & Commissioning 5 KVA Online UPS System with minimum 120 minutes Battery Backup on SMF Batteries & suitable arrangements / cabinet for Batteries, complete with all necessary accessories and as per technical specifications |
| 100 | Supplying, Installation, Testing & Commissioning of All in 1 Desktop (24 Inch) with Window Licenses complete with all necessary accessories complete all as per technical specification in DPR, Including Anti virus Software |
| 101 | Supply, Installation, Testing, Commissioning CCTV Dome & PTZ Cameras including installation & all accessories and as per technical specifications present in DPR |
| 102 | Supply, Installation, Testing, Commissioning Server based NVR with HDD Storage 30 days complete all as per technical specifications |
| 103 | Supply, Installation, Testing, Commissioning 8 Port POE switch for CCTV Camera (Each Floor) with all accessories and as per technical specifications |
| 104 | Supply, laying, of cat6 cable with RJ45 including all accessories and as per technical specifications , including conduit |
| 105 | Supply, Installation, Testing, Commissioning of 43, Inch LED TV including all accessories and as per technical specifications Samsung, LG Xiaomi etc |
| 106 | Supply, Installation, Testing and commissioning of 5 MB Lease line for 1year complete all as per technical specifications |
| 107 | Network Resources & Infrastructure |
| 108 | Providing and Installation on site Sofa set with tubular steel frame, powdercoatedtorequiredcolour,with100mmthkcushionwith32 density PU foam for seat and back rest with 100mm cushion with 20 density PU foam, moulded polyurethane arm rest, complete in every respect: Bodyline regency of Feather lite or equivalent of Godrej / Bloplast.Three Seater |
| 109 | Reception Table |
| 110 | Common Chairs as per direction of engineer-in-charge |
| 111 | Workstation 900X1500 as per direction of engineer-in-charge |
| 112 | Common Chairs as per direction of engineer-in-charge |
| 113 | Furniture for library corner (10 Seater Desk with 20 Chairs) |
| 114 | 150Liters/hour L Water Cooler (Maximum Energy Consumption(Watt) 1550 Watt for 150 ltr/hr cooling cap.) All complete. As per |
| 115 | Fully automatic with auto cut off RO Potable Water Purification System (Filtration Capacity in liter/hour 50, Manufacturers Quality System Certifications ISO 9001:2015) All complete. As perDirection of engineer in charge |
| 116 | Computer Chairs as per direction of engineer-in-charge |
| 117 | Computer table as per direction of engineer-in-charge |
| 118 | Library Book Display Rack, metal storage made of a durableMaterial.5 Shelves |
| 119 | SUPPLYING, INSTALLATION, TESTING AND COMMISSIONING OF GRID INTERACTIVE ROOF TOP SOLAR PHOTO VOLTAIC POWER GENERATIONSYSTEM INCLUDINGSPACEFRAME (CPWD 6.8.1) 58480*0.735*106/107=42581.09 |
| 120 | Adding 18 % GST |
