Tender For The Work Of Painting Various Tehsils In Jhansi District - Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil. DSR Sl.No- 2.6.1 2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand (zone-III): 8 graded stone aggregate 40 mm nominal size). DSR-4.1.8). 3 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand).DSR-6.1.1 4 RCC work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR-5.2.2 5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. .DSR 2.25 6 Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in Cement mortar 1:6 (1 cement : 6 coarse sand).DSR-6.34.2 7 RCC work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).DSR-5.3 8 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.(Mild steel and Medium Tensile steel bars).DSR 5.22.1 9 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) .as per DSR 13.1.2. 10 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.as per DSR 13.26. 11 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. as per DSR 13.41.1. 12 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.as per DSR 13.48A.1 13 Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.as per DSR 11.37 14 Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.as per DSR 10.31 15 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture.as per DSR 13.48.3 16 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1 17 SANITARY WORK :-Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : (W.C. pan with ISI marked white solid plastic seat and lid). DSR no - 17.2.1 18 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. DSR 17.1.1 19 Providing and fixing wash basin with C.I. brackets, 15 mm A.K. brass pillar taps, 32 mm A.K. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm A.K. brass pillar tap). DSR no - 17.7.4 20 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.waste fittings complete Semi rigid pipe. DSR 17.28.1(A) 32 mm dia pipe for Wash Basin, DSR 17.28.1.1 21 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.waste fittings complete Semi rigid pipe. DSR 17.28.1(B) 40 mm dia pipe for Sink, DSR 17.28.1.2 22 Providing and fixing PTMT Bottle Trap for Wash basin and sink, Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. DSR 17.70.2 23 Providing and fixing Rectangular shape 1500x450 mm mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :.DSR no.- 17.32.4 24 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and A.K. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (One urinal basin with 5 litre white P.V.C. automatic flushing cistern ).DSR no -17.4.1 25 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.(600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. ). DSR no -17.73.2 26 Providing and fixing A.K. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.(15 mm nominal bore.)DSR no -18.52.1 27 Providing and fixing A.K. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :(15 mm nominal bore.) DSR no -18.53.1 28 Providing and fixing brass bib cock of approved quality : (15 mm nominal bore ).DSR no -18.15.1 29 Providing and fixing brass bib cock of approved quality : (20 mm nominal bore ).DSR no -18.15.2 30 Providing and fixing PTMT urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long. 42 mm high and 30 mm wide with BSP female threads weighing not less than 48 gms. DSR 17.76.1 31 Supply and installing of low density polyethylene seamless one peace moulded tank and placing the same in proper position including all taxes labour and T&P etc for proper completion of the work. Tank should be ISI marked (for 500 Liters) As per SOR SI No-New item-1, Ch-19. 32 S/F of Fullway Gate Valveheavy quality 75 mm dia ISI marked including cutting and threadingas requiredS/o all material labour T&P etc.Sl.No-54,Ch-21 33 Supply and fixingof 50 mm dia PVC pipe complete with rose heads bends M.S Clamps 2.5 cm x 3 mm fixed to walls by 15 cm Long 6 mm dia nail and including repair of plaster pointing etc if damaged during fixing of the pipes including cost of all material labour, tools and plant etc required for proper completion of work. As per SOR SI No-New item-5, Ch-19. 34 Supply and fixingof 75 mm dia PVC pipe complete with rose heads bends M.S Clamps 2.5 cm x 3 mm fixed to walls by 15 cm Long 6 mm dia nail and including repair of plaster pointing etc if damaged during fixing of the pipes including cost of all material labour, tools and plant etc required for proper completion of work. As per SOR SI No-New item-4, Ch-19. 35 Supply and fixing brass bib cock heavy quality 15 mm dia (400 gms) ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-42,Ch-21 36 Supply and fixing A.K. piller cock with Brass spindle 15 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-87,Ch-21 37 Supply and fixing P.V.C ball float valve with brass and union complete 25 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-37,Ch-21 38 Supply and fixing G.I. Cross Tee 25 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-30,Ch-21 39 Supply and fixing G.I. Socket 25 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-22,Ch-21 40 Supply and fixing G.I. Socket 50 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-24,Ch-21 41 Supply and fixing G.I. Elbow 25 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-18,Ch-21 42 Supply and fixing G.I. Elbow 24 mm dia ISI marked including supply of all materials, labour and T&P etc. required for proper completion of work.Si no-19,Ch-21 43 Supply and fixing OFFICE HUB Cantilever Office Chair Non-revolving and non-tilting chair with armrest. required for proper completion of work.(As per GEM Rate)
