Comprehensive Maint Of B/R Services At Zone D Under Age B/R Dett-Iii Of Ge 862 Ews; 1 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings, complete all as specified and directed. 2 S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/ cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed. 3 S&F for Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed. 4 S&F for Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof bent to a curve of any radius as directed by GE fixed with self tapping screws including side end lap as per manufacturers instructions, complete all as specified and directed. 5 Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/blankets of any thickness, including cover filters, complete all as specified and directed. 6 S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per instructions, complete all as specified and directed. 7 Dismantling structural steel work including welded fabriks frames, doors, gates, grills grating and framed truss etc, complete all as specified and directed. 8 M&L for rolled section as in main and cross beams / columns, hip and jack, rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates (Fe-410 W Gde E-250 Quality A) complete all as specified and directed. 9 M&L for mild steel framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forget into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks or portion framed and hung as gates, including pintel hinges, stops, hand made sliding bolt, hold fast etc and similar work conforming to Fe 290 or E-165 work including welded fabricks frames, gate and framed truss etc, complete all as specified and directed. 10 M&L for preparation of new or previously untreated steel surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified. 11 M&L for preparation of new wooden surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. 12 M&L for preparation of old steel surface of any description exc 10cm width or girth and applying one coat of synthetic enamel paint any tint including preparation of surface, complete all as specified and directed. 13 M&L for preparation of old wooden surface of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 14 Hacking out old broken glass of any thickness, size, quality or description) from wooden frames, glazed with putty or fixed with beads, complete all as specified and directed. 15 S&F for 3 mm thick sheet glass ordinary quality and glazing with oil putty / wooden beads in squares not exc 0.50 sqm in each pane, complete all as specified and directed. 16 S&F in repairs for 5 mm thick sheet glass ordinary quality and glazing with oil putty / wooden beads in squares not exc 0.50 sqm in each pane, complete all as specified and directed. 17 S& F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed. 18 S& F in repair for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed. 19 S&F for 3 mm thick figured glass pin headed type and glazing with oil putty in squares n . exc 0.50 sqm in each pane, complete all as specified and directed. 20 Taking down cement plaster, any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 21 M&L for rendering 15 mm thick on concrete surface / brick surface on wall in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and directed. 22 M&L for 20 mm thick rendering on other than fair faces of brick surface or stone masonry surface in cement mortar 1:6 surface finished even & smooth without using extra cement, complete all as specified and directed. 23 M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surface of ceiling, finished surface even and smooth without using extra cement, complete all as specifed and directed. 24 M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer and a coat of wall care putty 1.5mm thick, complete all as specified and directed. 25 M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer including preparation of surface, complete all as specified and directed. 26 M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer, complete all as specified and directed. 27 M&L for preparation of old plastered surfaces of walls with complete removal existing treatment and applying two coats of cement base paint over a coat of primer, complete all as specified and directed. 28 M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. 29 Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles, complete all as specified and directed. 30 M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar 1:6, complete all as specified and directed. 31 M&L for brick work with sub class B bricks, old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4 , complete all as specified and directed. 32 M&L for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down existing GI tubes complete all as specifed and directed. 33 M&L for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down existing GI tubes complete all as specifed and directed. 34 S&F repair for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed. 35 S&F in repair for 15 mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed. 36 S&F in repair for PVC waste pipe 900mm long suitable for wash hand basins and urinals including connecting, complete all as specified and directed. 37 S&F in repair 15mm CP brass health faucet (hand shower) inlet length 100mm fixed to angle valve with and including decorative choice flexible pipe, wall hanger etc, complete all as speicified and directed. 38 S&F in repair for 15mm bore bib tap cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed. 39 S&F in repair for 15mm bore stop valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed. 40 S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed. 41 S&F as in repair for viterous China water closet pedestal pattern in one piece type of dimention 73cmX36cm74cm including seat cover and gaset, floor mounted, P or S trap, flushing kit, CP jet with PVC pipe of superior quality and all necessary fixing arrangements, complete all as specified and as directed. 42 S&F in repair for viterous china wash down water closet pan, white (pedestal pattern), including PVC flushing cistern 10 ltr capacity and fixed in floor with brass screw, plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, and inlcuding set of CP jet spray with flexible PVC pipe of superior quality, complete all as specified and directed. 43 S&F in repair of copper alloy chromium plated jet spray suitable for padestal pattern WCs including decorative choice flexible pipe fixed to iron pipe with and including cover plate, complete all as specified and directed. 44 S&F in repair for PVC connection pipe 15 mm x 600 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed. 45 S&F in repair for vitreous china wash hand basin white, flat back, size 550x400mm size including pedestal, cutting for and pinning ends of brackets or erecting stand, complete all as specified and directed. 46 S&F in repair vitreous China coloured, counter top wash hand basin, ovel type, size 550mm including cutting for and pinning in but exc waste pipe, complete all as specified and directed. 47 S&F in repair for vitreous China water closet (squatt pan) Orrisa pattern 580x440 mm size pan, white, with front or back inlet with integral foot rests including provn of lime concrete bedding including connections to flushing cistern/pipe including trap set in concrete and removing debries from site, complete all as specified and directed. 48 S&F in repair of CP brass WHB mixers for hot and cold water mixing of 15mm dia screwed down for iron pipe, complete all as specified and directed. 49 S&F in repair for 15 mm bore brass chromium plated wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed. 50 S&F in repair for 15mm bore brass chromium plated brass wall mixer 2 in 1 two for hot and cold water mixing and one for shower rose, complete all as specified and directed. 51 S&F in repair for 15mm bore swan neck, pillar cock, cast copper alloy, with capstan heads, chromium plated, fancy type, screwd down high pressure , with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed. 52 S&F in repair for 15mm bore Angle valve, cast copper alloy, fancy type, chromium plated suitable for iron pipe and one end and PVC connector on other, complete all as specified and directed. 53 S&F for in repair sink with draining board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 600mm x 450mm x 160mm, complete all as specified and directed. 54 S&F in repair for assembled ready to use rectangular stainless steel (Grade 304) kitchen plate rack with 3-4 shelves, enclosed four sides by SS plain sheet, 0.6 mm squre support pipes, dedicated holes for spoon, pegs etc cover all size 600mmx750mmx250mm of standard pattern, complete all as specified and directed. 55 S&F for rotational moulded polythylene two layered white coloured water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed. 56 S&F for rotational moulded polythylene two layered white colour water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed. 57 S&F in repair for grating doom 100mm dia of PTMT (Min Weight 25 Gms) with waste hole, complete all as specified and directed. 58 Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 59 M&L for vitrified tiles light shade (premium quality) 7-8 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed. 60 M&L for vitrified tiles light shade (premium quality) 7-8 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in dados / skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed. 61 M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4, complete all as specified and as directed. 62 M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm or 450x350x7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. 63 Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level and removal of debris from site, complete all as specified and directed. 64 M&L for 75mm thick plain cement concrete 1:3:6, type C-2, (using 20mm graded crushed stone aggregate) as in path / sub base to receive tiles, complete all as specified and directed. 65 M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed. 66 M&L for plain cement concrete 1:2:4, type B-1, (using 20 mm graded crushed stone aggregates) as in surface channel and drains, complete all as specified and directed. 67 M&L for 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) as in sub base surface finished even and rough to receive tiles, complete all as specified and directed. 68 M&L for Machine cut kota stone slab (mirror polished) flooring 18-20mm thick as in floors and jointed with grey cement slurry mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including screed bed or bedding layer of 20 mm thick in cement mortar 1:4 including taking down old kota stone, complete all as specified and directed. 69 M&L for 18-20mm thick granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, cooking platforms, in steps, pillars, window cills, etc, laid over 20mm thick bedding in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite slab, rounding edges cutting, polishing etc including taking down old granite stone, complete all as specified and directed. 70 M&L for formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete, complete all as specified and directed. 71 M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed. 72 Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed. 73 M&L for RCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, including demolition of old RCC work, complete all as specified and directed. 74 M&L for mild steel TMT bars 10 to 12mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. 75 M&L for mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. 76 Taking down chowkhats or frames (without taking off shutters from the frames) exc 1.5 Sqm and n. exc 4 Sqmm each and removing from site including making good to disturbed portion, complete all as specified and directed. 77 Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each and refixing in same opening with necessary fittings complete all as specified and directed. 78 S&F for powder coating of any colour (thickness of powder coating not less than 50 micron & min thick n. less than 2mm) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed. 79 S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium door shutters, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM /neoprene gasket required (fittings shall be paid for separately) with extruded built up standart tubular section /appropriate Z-sections and other sections of approved make conforming to IS 733 and IS 1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws all complete as per architectural drawings, complete all as specified and directed. 80 S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium work for doors, windows & ventilators and partitions (Fixed portions) with extrufed built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws all complete as per architectural drawings, complete all as specified and directed. 81 S&F for 100mm long butt hinges medium weight cold rolled mild steel (ISI Marked) , complete all as specified and directed. 82 S&F for 75 mm size mortice lock of brass, vertical type, 4 levers (ISI Marked), complete all as specified and directed. 83 S&F door closer hydraulically regulated, aluminium (extruded section body) designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg (ISI Marked), Complete all as specified and directed. 84 S&F for aluminium anodized aluminium alloy american handle type 200 mm long of extruded section (ISI marked) ,complete all as specified and directed. 85 S&F in repairs door closer hydraulically regulated, aluminium (extruded section body) designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg (ISI Marked), Complete all as specified and directed. 86 S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed (ISI Marked), complete all as specified and directed. 87 S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified and directed. 88 S&F for powder coated anodised aluminium window and ventilator shutters, (minimum thickness of power coating not less than 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21, 100mm long (3 Nos) suitable handle (2 Nos), complete all as specified and directed 89 S&F for powder coated anodised aluminium three track slinding window, (minimum thickness of power coating not less than 50 micron) with two or more shutter with 4mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock etc including 65x39.5x1.5mm section for complete frame and rubber beading and glazing clips etc using following sections as given in JINDAL catelouge including taking down of existing old window of any description, complete all as specified and directed 90 S&F for anodised aluminium grills 10mm dia decorative type 75mm mesh size including taking down old grills, complete all as specified and directed 91 M&L for 12mm thick prelaminated particle board, interior grade both side decorative choice lamination fixed to aluminium doors or similar works, complete all as specified and directed. 92 S&F for plain ACP board 5mm thick, fixed in aluminium doors or similar work including cutting, packing, finishing, complete all as specified and directed. 93 S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane, complete all as specified and directed. 94 S&F for pressed steel door frames of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC 1:3:6, type C-0 using 12.5mm graded crushed stone agregate, complete all as specified and directed. 95 S&F for pressed steel frame for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock and strike plate etc including back filling of chowkhats with PCC 1:3:6, type C-1 using 20mm graded stone agregate, complete all as specified and directed. 96 S&F for factory made 40mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed 97 S&F for factory made 2nd class hard wood 30 mm thick plain framed panelled shutters (any No of panels) with panels of timber flat on both sides (feather edges) or of veneered particles board medium density wood particle board with commercial face veneers, fixed to chowkat, complete all as specified and directed. 98 S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed. 99 M&L for 300mm long mild steel sliding door bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate (ISI Marked), complete all as specified and directed. 100 M&L for aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, (ISI Marked), complete all as specified and directed. 101 M&L for 300mm MS ordinary rat tail rod pattern door springs (ISI marked) including roller and roller plate, complete all as specified and directed. 102 S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and and as directed and as shown on drwaing. 103 S&F for factory made solid panel PVC door shutter 28 to 30mm thick (stiles) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed. 104 S&F for aluminium anodized barrel tower bolts 150 mm long of extruded section (ISI marked), complete all as specified and directed. 105 S&F for 100mm long butt hinges medium weight cold rolled mild steel (ISI Marked) , complete all as specified and directed. 106 S&F for extruded aluminium alloy handles size 150 mm fabricated type anodised (ISI marked), complete all as specified and directed. 107 M&L for overhead PVC tank cleaning of any capacity including dismantling and setting aside or lowering if required for repairs, cleaning, etc and hoisting if required reconnecting and re- fixing in same position after cleaning and removing all scale and dirt etc from tank and from mouths of circulating pipes etc, including replacement of required fittings such as PVC ball valve with brass rod, tank nipple etc, complete all as specified and directed. 108 M&L for 75mm thick plain cement concrete, type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed. 109 S&F in repair for glass corner shelf with tempered galss, stainless steel brackets and polished chrome finish rail , complete all as specified and directed by Engr-in-Charge. 110 S&F in repair for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed. 111 S&F in repair for 15mm bore Stop valve (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, with long shank and cup, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. 112 Dismantling boarding any description fixed in any positioni with nails, complete all as specified and directed. 113 M&L for PVC wall paneling of approved shade and colour, UPVC hollow sections 9-10mm thick & 1mm thick wall thickness printed / designer, joined together with groove and tennon joints and fixed with screws on walls, finishing sides and top with U or T or any other suitable PVC section matching the shade of panels including preparation of wall surface if required including dismantling of old PVC wall panelling, complete all as specified and directed. 114 S&F in repair 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specifed and directed by Engr-in-Charge. 115 S&F in repair 110 mm bore PVC (SWR) bend any radius with access door, complete all as specifed and directed by Engr-in-Charge. 116 S&F in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors or trenches, complete all as specifed and directed by Engr-in-Charge. 117 S&F in repair 75 mm bore PVC (SWR) bend any radius with access door, complete all as specifed and directed by Engr-in-Charge. 118 S&F in repair for chromium plated brass shower rose of size 125mm with swivel joints fixing to steel pipes etc, complete all as specified and directed by Engr-in-Charge. 119 M&L for factory made 100% solid WPC door frame 90mm x 45mm single rebated made from wood polymer composite (single extruded process) material comparising of vigin PVC polymer of K value 57-60 (suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 kg/cbm & manufactured by RAJSHRI an certified by ISO 9001-2015, having good screw holding capacity (screw withdrawel strength of min 990N), min compressive strength of 58N/Sqmm, modulus of elasticity 900 N/Sqmm and resistance to spread of flame of class A category with property of being termite /borer proof, water /moisture proof & fire retardant & fixed in position with SS dash fastener / hold fast of required dia and length, all as per specification, drawing and as directed by Engineer-in-Charge.Note: Material test certificate and authentication should be compusory provided by the manufacturing company, complete all as specified and directed. 120 M&L for factory made of 30mm thick 100% solid WPC laminated moduled door shutter comparising of vigin PVC polymer of K value 57-60 (suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extrauded (inner) with having minimum frame density not less than 650 kg/cbm & manufactured by RAJSHRI an certified by ISO 9001-2015, having good screw holding capacity (screw withdrawel strength of min 2000N) (Face) & 1100 N (Edge), min compressive strength of 50N/Sqmm, modulus of elasticity 850 N/Sqmm and resistance to spread of flame of class A category with property of being termite /borer proof, water /moisture proof & fire retardant. WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted on both faces of shutter and fixing stainless steel butt hings of required size with necessary full body threaded star headed counter sunk SS screwes, all as per specification, drawing and as directed by Engineer-in-Charge.Note: Material test certificate and authentication should be compusory provided by the manufacturing company, complete all as specified and directed. 121 M&L for factory made 100% solid WPC door frame 125mm x 65mm single rebated made from wood polymer composite (single extruded process) material comparising of vigin PVC polymer of K value 57-60 (suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 kg/cbm & manufactured by RAJSHRI an certified by ISO 9001-2015, having good screw holding capacity (screw withdrawel strength of min 990N), min compressive strength of 58N/Sqmm, modulus of elasticity 900 N/Sqmm and resistance to spread of flame of class A category with property of being termite /borer proof, water /moisture proof & fire retardant & fixed in position with SS dash fastener / hold fast of required dia and length, all as per specification, drawing and as directed by Engineer-in-Charge.Note: Material test certificate and authentication should be compusory provided by the manufacturing company, complete all as specified and directed. 122 M&L for factory made of 30mm thick 100% solid WPC laminated skeleton door shutter comparising of vigin PVC polymer of K value 57-60 (suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extrauded (inner) with having minimum frame density not less than 650 kg/cbm & manufactured by RAJSHRI an certified by ISO 9001-2015, having good screw holding capacity (screw withdrawel strength of min 2000N) (Face) & 1100 N (Edge), min compressive strength of 50N/Sqmm, modulus of elasticity 850 N/Sqmm and resistance to spread of flame of class A category with property of being termite /borer proof, water /moisture proof & fire retardant. WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted on both faces of shutter and fixing stainless steel butt hings of required size with necessary full body threaded star headed counter sunk SS screwes, all as per specification, drawing and as directed by Engineer-in-Charge.Note: Material test certificate and authentication should be compusory provided by the manufacturing company, complete all as specified and directed. 123 S& F in repair for 600m x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 124 S&F in repair for brass CP soap dish including brass CP screws and wooden cleats,, complete all as specified and directed. 125 S&F factory made uPVC white colour three track three panels sliding window with fly proof SS wire mess (two Nos glazed & one No mesh panel) upto 1.50m height made of (big series) frame 116 x 45mm & sash 46 x 62mm both vaing wall thickness of 2.3 + 0.2mm and single glazing bead/ doubleglazing bear of appropriate dimension. (Area of window above 1.75sqm) comprising of uPVC multi chambered frame, with inbuild roller track and sash extruded profiles duly reinforced with 1.60 + 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropirate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook zinc alloy body with sinle nylon rollers (weight bearing capacity to be 40kg), GI fasteners 100x8mm size for fixing frame to finished wall and necesary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing dardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engr-in-Charge. (Glass or wiremesh shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimensoin i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in hgiher side shall be accepted but no extra payment on this account shall be made. ; Old unserviceable CGI sheet of any type Sqm 210 50.00 10500.00 2 Old unserviceable AC ceiling boards including of any type. Sqm 70 25.00 1750.00 3 Old unserviceable brick bats. Cum 8 500.00 4000.00 4 Old unserviceable PVC water storage tank of 500 ltrs capacity of any description Each 6 150.00 900.00 5 Old unserviceable PVC water storage tank of 1000 ltrs capacity of any description Each 8 250.00 2000.00 6 Old unserviceable bib taps, pillar taps, stop valve, health faucet, shower rose, CP Jet spray, nozzle, soap dish holder, PVC connection, ball valve etc. Each 96 25.00 2400.00 7 Iron scrap Kg 650 20.00 13000.00 8 Aluminium scrap Kg 120 50.00 6000.00 9 PVC scrap Kg 5 5.00 25.00 10 Old unserviceable wooden door shutter with chowkhat exc. 1.5 Sqm n. exc 4.00 sqm including iron mongry & hold fast Each 35 300.00 10500.00 11 Old unserviceable wooden door shutter with chowkhat n. exc. 1.5 Sqm including steel mongry & hold fast Each 15 250.00 3750.00 12 Old unserviceable shutter exc. 2 Sqm each Each Leaf 10 200.00 2000.00 13 Old unserviceable steel wire cloth of any size Kg 10 20.00 200.00 14 Old unserviceable wash hand basin of any size Each 5 50.00 250.00 15 Old unserviceable PVC flushing cistern of any type &size Each 25 25.00 625.00 16 Old unserviceable of GI tubing 15 dia of any type RM 75 15.00 1125.00 17 Old unserviceable GI tubing 20mm dia of any type RM 25 20.00 500.00 18 Old unserviceable stainless steel kitchen sink of any size Each 3 300.00 900.00 19 Old unserviceable stainless steel kitchen plate rack of and size Each 5 300.00 1500.00 20 Old unserviceable PVC wall paneling Sqm 60 15.00 900.00 21 Old unserviceable WHB CP mixer Each 5 200.00 1000.00 22 Old unserviceable sink / wall brass mixer Each 7 250.00 1750.00
