|
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically providedcomplete all as specified & directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level)complete all as specified & directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) of any thickness and in any positionand removing serviceable tiles to store and rubbish off the premises complete all as specified & directed. |
| 4 | Dismantling and breaking up drain pipes (salt glazed ware, AC, reinforced concrete, PVC or Cast iron) set in cement mortar of size 100mm/75mmfixed over wall or in floor including clamps etc., complete all as specified & directed. |
| 5 | Taking down cement rendering/plastering of any thickness and of any description including raking out joints, hacking for key, scrubbing down with water etc., over wall or ceiling surfaces complete all as specified & directed. |
| 6 | Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters(without taking off shutters from the frames) including hold fasts from wall and making good in cement mortar 1:4 complete all as specified & directed. |
| 7 | Taking down chowkhats or frames exceeding 1.5Sqm each but not exceeding 4Sqm each with shutters(without taking off shutters from the frames) including hold fasts from wall and making good in cement mortar 1:4 complete all as specified & directed. |
| 8 | Taking down shutter of any description and material exceding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed. |
| 9 | S&Fsolar control film 50 micron reflective type/frosted sticked to glass panes as per instructions of manufacturers complete all as specified & directed. |
| 10 | S&F stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified & directed. |
| 11 | S&F in repairscounter/table top vitreous China wash hand basin, of size 550X400X160mm white in colour,and 32mm bore dia CP finish copper alloy waste fitting/coupling, 32mm bore dia bottle trap including cutting for and pinning complete all as specified & directed. Make:- Cera Cat Part No. S2020102PL or equivalent make as specified in list of manufactures of Particular Specifications |
| 12 | S&F in repairs15mm bore dia fancy wash basin long body pillar cock including necessary connecting pipe, screwed down, screwed for water pipe complete all as specified & directed. Make:- Cera Cat Part No. F1013111 or equivalent make as specified in list of manufactures of Particular Specifications |
| 13 | S&F 5.5 mm thick bevelled edge mirror of selected quality glass ,mounted on 17mm to 18 mm thick WPC board fixed to wooden plugs with chromium plated \"D\" cut accessories, screws and washer complete all as specified & directed. |
| 14 | S&F 12mm thick toughned glass fixed in windows/stair case railing of any material and description of required size, the edges of glass to be finished as clear polish including necessary cutting for nut bolt/screws/patch fittings etc completeallas specified and directed |
| 15 | Dismantalling of wall and ceilingboards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work completeallas specified and directed |
| 16 | M&L for Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturer\"s instructions(metal frame work paid separately) completeallas specified and directed |
| 17 | S&F Gl frame work (size of grid not exc. 605mmX605mm) for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre completeallas specified and directed. |
| 18 | S&F 12mm thick High Pressure Panel Board as in Partition wall andDoor with the following specifications:-(a) The Panel shall be fixed in wall through standard SS profile (Wall bracket). (b) The top of Panel shall be fixed through standard SS profile( H-type top rail with cover)(c)The \"T\" junction of panel shall be fixed through standard SS profile. The bottom of panel shall be fixed through standard SS profile adjustable foot of Minimum 75mm height.(d) The Panel door shall have standard SS,hinge (spring loaded butt hinge), door Knob pair, privacy thumbturn, locking arrangement, floor anchor, occupancy indicatoretc.(e) The each shutter shall have one SS Coat Hook cum door stopperMake:- HPL/Greenlam Laminates/Alstone India/Merino Laminates |
| 19 | S&F 12mm thick High Pressure Panel Board over wall &shall be fixed in wall through standard aluminium section with riveting.as per size & design complete all as specified & directed.Make:- HPL/Greenlam Laminates/Alstone India/Merino Laminates |
| 20 | S&F in repairssingle piece white colour vitreous China floor mounted pedestal pattern wash down water closet having PVC/CI\"P\" or \"S\" type trap element, rimless one pieceincluding all accessoreis i.e; seat cover, 1.5m flexible PVC pipe and CP finish cast copper alloy 15mm bore dia health faucet, 15mm bore dia PVC connection pipe 450mm long, including CP finish copper alloy two way fancy bib cock 15mm bore dia complete all as specified & directed.Make:- Cera, Cat Part No. S1013217or equivalent make as specified in list of manufactures of Particular Specifications Note: Joints between floor and WC shall be filled with silicon jel and screws required for fixing shall have stainless steel of required size shall be included in the quoted rates. |
| 21 | S&F in repairsfancy type 15mm bore dia long body fancy type bib tap chromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 22 | S&Fin repairsfancy type 15mm bore dia short body fancy type bib tap chromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 23 | S&Fin repairs15mm bore dia fancy angle stop valve, chromium plated, cast copper alloy,screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 24 | S&FPVC connection 15mm size with PTMT nuts of length 450mm complete all as specified & directed. |
| 25 | S&FPVC connection 15mm size with PTMT nuts of length 600mm complete all as specified & directed. |
| 26 | S&Fin repairs10 liter PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, and handle/push type, including 32mm bore dia PVC long/short flusing pipe andbrackets complete all as specified & directed. Make: Jaquar, Cera, Hindware, Prayag or equivalent make as specified in list of manufactures of Particular Specifications |
| 27 | S&F in repairs fancy type square shape of minimum size 100mmX100mm swivel shower of cast stainless steel, including CP finish shower rod (long) and cup washer/wall flange for fixing with 15mm bore dia pipe/fittings complete all as specified & directed. |
| 28 | S&F in repairstubular brass chromium plated Towel rail 20mm dia \"D\" type 60cm long between flanges complete all as specified & directed. |
| 29 | S&F in repairsCP finish soap dish cast stainless steelfixed to plugs complete all as specified & directed. |
| 30 | S&F in repairs , 15mm bore dia, cast copper alloy CP finish wall mixer (3 in 1)cast copper alloy, for mixing hot & cold water screwed down for water pipe/fittings including hand shower with flexible pipe complete all as specified & directed. |
| 31 | S&F wall mounted Sheet glass shelf assembly consisting of acrylic sheet shelf 12cm wide with chromium plated bracket guard and railing, 60cm long complete all as specified & directed. |
| 32 | S&F wall mounted Sheet glass corner shelf assembly consisting of acrylic sheet shelf 20cm wide and 30cm long each side with chromium plated bracket guard and railing, complete all as specified & directed. |
| 33 | Taking down shutter of any description and material (Wooden,Aluminium/UPVC) from frame/chowkhat exceeding 1Sqm but not exceeding 3Sqm each and re-fixing in the same opening after necessary repairs ing, ease and adjust, cutting, grinding, adjusting,including using new nails/screws completeallas specified and directed. Note: Material required other than mentioned in this item for repairs ing shall be paid under respective supply only item. |
| 34 | Taking down shutter of any description and material (Wooden,Aluminium/UPVC) from frame/chowkhat not exceeding 1Sqm each and re-fixing in the same opening after necessary repairs ing, ease and adjust, cutting, grinding, adjusting,including using new nails/screws completeallas specified and directed. Note: Material required other than mentioned in this item for repairs ing shall be paid under respective supply only item. |
| 35 | S&F in repairs stainless steel wire cloth 0.36mm dia of wire and average width of aperature 1.40mm and fixed in wooden/steel door/window shutters including new second class hard wood beading of required size to secure the wire cloth/mesh/welding/nut bolt completeallas specified and directed. |
| 36 | S&F 4mm thick sheet glass, ordinary quality, in squares, pane including taking down from wooden/steel/aluminium shutter of any description including using necessary size of second class hard wood beading to secure the glasss completeallas specified and directed. |
| 37 | Supply only 100mm medium weight mild steel butt hinges completeallas specified and directed. |
| 38 | Supply only 100mm medium weight stainless steel butt hinges including necessary stainless steel screws of reqd size completeallas specified and directed. |
| 39 | S&F150mm long cast type anodised aluminium handle type complete all as specified & directed. |
| 40 | S&F100mm long aluminium anodised hasp and staple, safety type,with mild steel hinge pin including bolt to hinge plate and fixed with screwscomplete all as specified & directed. |
| 41 | S&Ffloor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece complete all as specified & directed. |
| 42 | Supply only 150mm long cast type anodised aluminium handle type complete all as specified & directed. |
| 43 | Supply only 100mm long aluminium anodised hasp and staple, safety type,with mild steel hinge pin including bolt to hinge plate and fixed with screwscomplete all as specified & directed. |
| 44 | Supply only floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece complete all as specified & directed. |
| 45 | S&Fin repairsfor 250mm length of bolt, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. |
| 46 | S&Fin repairs200mm long aluminium, anodised barrel tower bolts of extruded section complete all as specified & directed. |
| 47 | Supply only for 250mm length of bolt, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. |
| 48 | Supply only 200mm length of bolt, aluminium anodised barrel tower bolts of extruded section, complete all as specified & directed. |
| 49 | S&F factory made single extruded WPC (Wood Polymer Composite) solid one side decorated and other side plain flush door shutter of 30mm thickness comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 50 | S&F17mm to 18mm thick WPC board of approved make of one side prelam/rigidlam and other side plain colour fixed with screws, solvent cement/adhesive to make cup board/ cabinet shutters/drawer front/sides, partitions, shelves etc. including 1mm thick PVC lipping/beading fixed with solvet over edges of ply of required width and colour complete all as specified and directed. |
| 51 | S&Fsleek soft hydraulic auto closing 3D (Big bend/middle bend/straight arm type) stainless steel finish hinges openable of 0 or 15 degree crank for cup board/ cabinet shutters (sample available in GE Office) complete all as specified and directed. Make: Hettich, Harrison, Earl Bihari |
| 52 | Supplying and laying of 15mm nominal size UPVC pipes of pressure rating 10Kgf per Sqcm including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall/ceiling or laying in floors and necessary cutting/chases in wall/floor of any description and their making good including taking down of existing tubing completeallas specified and directed. |
| 53 | Supplying and laying of 20mm nominal size UPVC pipes of pressure rating 10Kgf per Sqcm including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall/ceiling or laying in floors and necessary cutting/chases in wall/floor of any description and their making good including taking down of existing tubing completeallas specified and directed. |
| 54 | Supplying and laying of 25mm nominal size UPVC pipes of pressure rating 10Kgf per Sqcm including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall/ceiling or laying in floors and necessary cutting/chases in wall/floor of any description and their making good including taking down of existing tubing completeallas specified and directed. |
| 55 | S&Fto chowkats 28mm to 30mm thick factory made wire mesh solid WPC door shutter consisting of density 650 Kg /Cum manufactured by an ISO-9001-2015 certified company , door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws. other hardwares should be fixed with 19x6mm size steel screws etc., complete as per direction of Engineer-in -Charge and, manufacturer\"s specifications |
| 56 | S&F in repairshigh grade plastic, bath room mirror cabinet of size 450mmX350mm & 3mm thick looking mirror of make Modifloat or equivalentfixed to wooden/PVC plugs with screws complete all as specified & directed. Make: Prayag, Hindware, Cera or equivalent make as specified in list of manufactures of Particular Specifications |
| 57 | S&F in repairs , 600 mm x 450 mm bevelled edge mirror of selected quality glass ,mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screws and washer complete all as specified & directed. |
| 58 | S&F in repairsToilet paper holder with flat recessed type stainless steel material complete all as specified & directed. Make Jaquar, Cera, Hindware or equivalent make as specified in list of manufactures of Particular Specifications |
| 59 | S&F in repairsvitreous Chinawash down water closet pan,pedestal patternwhite (excluding flushing cistern) including plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified & directed. |
| 60 | S&F in repairsvitreous China squatting pan,‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including necessary PCC bedding, \"P\" or \"S\" PVC trap connected to PVC/CI pipes completeallas specified and directed. |
| 61 | M&L for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 50gm of bleaching powder per tank after disconnecting of outlet pipe and re-connecting in the same position, capacity of tank exc. 250 litres but not exc. 500 litres each and marked on tank with white synthetic enamel paint as \" tank cleaned on ________\" using stencil completeallas specified and directed by Engineer-in-Charge. |
| 62 | M&L for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 70gm of bleaching powder per tank after disconnecting of outlet pipe and re-connecting in the same position, capacity of tank exc. 500 litres but not exc. 1000 litres each and marked on tank with white synthetic enamel paint as \" tank cleaned on ________\" using stencil completeallas specified and directed by Engineer-in-Charge. |
| 63 | S&FPVC water storage tank cover of 500/1000 liter capacity of any description and shape as per existing water storage tank including necessary locking facility completeallas specified and directed |
| 64 | S&F in repairs vitreous China half stall urinal of size 350X340X615mm, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement; fixing to flushing cistern, flush pipe, 40mm bore dia CP finish cast copper alloy waste fitting completeallas specified and directed. |
| 65 | S&F in repairs32/40mm dia PVC flexible waste pipe for wash hand basin, kitchen sink, urinal or similar work completeallas specified and directed. |
| 66 | S&F in repairs32/40mm dia CP finish cast copper alloy waste fitting for wash hand basin, with long screwed shanks and fly nut and flange end, bedded in red lead cement completeallas specified and directed. |
| 67 | S&F in repairsCP finish cast copper alloy waste fitting for stainless steel kitchen sink, as per existing size and designs, with long screwed shanks and fly nut and flange end, bedded in red lead cement completeallas specified and directed. |
| 68 | M&L for pre-cast cement concrete block, (1:3:6), type C1 (using 20mm nominal size, crushed and graded stone aggregate) masonry with solid blocks and setting in cement mortar (1:4) having minimum compressive strength of 50 Kg per Sqcm including taking down existing masonary work complete all as specified & directed. |
| 69 | M&L for cement concrete, 25mm thick, (1:2:4), type B-0 (using 12.5mm nominal size crushed andgraded stone aggregate) for levelling/to receive screed for laying floor finish, finished fair and even complete all as specified & directed. |
| 70 | M&L for cement concrete, 75mm thick, (1:2:4), type B-1 (using 20mm nominal size crushed andgraded stone aggregate)for sub-base of floors & pavings or similar work finished fair and even complete all as specified & directed. |
| 71 | M&L for cement concrete, 75mm thick, (1:3:6), type C-1 (using 20mm nominal size crushed and graded stone aggregate)for plinth protection including filling of expansion joint with bituminous mixture finished fair and even complete all as specified & directed. |
| 72 | M&L for cement concrete, 75mm thick, (1:4:8), type D-1 (using 20mm nominal size crushed andgraded stone aggregate)for sub-base of floors or of similar type of work finished fair and even complete all as specified & directed. |
| 73 | M&L for cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) as in coping, hold fast or of similar type of workincluding necessary form work complete in all respectas specified & directed. |
| 74 | M&L for sand filling under paver block/floors or in foundations including watering and consolidation complete all as specified & directed. |
| 75 | M&L for 60mm thick rubber mould, machine pressed, precast concrete interlocking paver block, rubber moulded of any shape and size confirming to IS 15658-2006, M-35 Grade of concrete with grey cement and pigment complete all as specified & directed. |
| 76 | M&Lfor coloured non-skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tiles exceeding 0.08 sqm but not exc 0.36 sqm in floor, set and jointed in neat cement slury and pointed in white cement with pigment to match the shade of tiles including cement screed bed or bedding layer of 15mm thick in cement mortar 1:4 complete all as specified & directed. |
| 77 | M&Lfor coloured glazed ceramic tiles joint less/edge cutted of sizearea of each tiles exceeding 0.08 sqm but not exc 0.16 sqm, 7mm thick as in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick backing/rendering in cement mortar (1:4) complete all as specified & directed. Note:- Those tiles fixed right angled to each other, the each tile should be chamfered/trim/sharp at 45 degrees at joint/corner/edge, the quoted rates are inclusive of this provn |
| 78 | M&Lfor joint less/edge cutted glazed/matt finish light/dark shade double charged Vitrified tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, set and jointed in neat cement slury over cement screed bed or bedding layer15mm thick in CM (1:4) complete all as specified & directed. |
| 79 | M&Lfor joint less/edge cutted glazed/matt finish light/dark shade double charged Vitrified tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, over and incl 10mm thick plastering in cement mortar 1:4 complete all as specified & directed. Note:- Those tiles fixed right angled to each other the each tile should be chamfered/trim at 45 degrees at joint/corner /edge, the quoted rates are inclusive of this provn |
| 80 | M&L for 15mm thick cement plaster in CM 1:6 over walls surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 81 | M&L for 15mm thick cement plaster in CM 1:4 over walls surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 82 | M&L for 10mm thick cement plaster in CM 1:3 over ceiling surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 83 | M&L for two coats of white washon old decorated ceiling surfaces including necessary filling of voids with wall care putty complete all as specified & directed. |
| 84 | S&F factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 85 | S&F in repairs25mm nominal bore bore dia CPVC, globe or gate valves, connected with pipe with solventof any material complete all as specified & directed. Make: Astral, Prince, Finolex |
| 86 | S&F 75mm bore dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with necessary clamps complete all as specified & directed. |
| 87 | S&F 75mm bore dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified & directed. |
| 88 | S&F 110mm bore dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with necessary clamps complete all as specified & directed. |
| 89 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified & directed. |
| 90 | S&F PVC (SWR) floor trap of outlet dia 75mm, plain with SS gratings 125X125mm size with openable circular grating with or without hole including jointing with solvent cement including fixing to pipe properly with solvent complete all as specified & directed. |
| 91 | S&F PVC (SWR) bends with access door for 75 mm bore pipe complete all as specified & directed. |
| 92 | S&F PVC (SWR) bends with access doorfor 110 mm bore pipe complete all as specified & directed. |
| 93 | S&F PVC (SWR) junction single, (Single T) equal or unequal size with access door for 75 mm bore pipe complete all as specified & directed. |
| 94 | S&F PVC (SWR) junction single, (Single T) equal or unequal with access door for 110mm bore pipe complete all as specified & directed. |
| 95 | S&F PVC (SWR) vent cowl 110 mm dia complete all as specified & directed. |
| 96 | S&F PVC (SWR) vent cowl 75 mm dia complete all as specified & directed. |
| 97 | Supply, hoisting and fixing of triple layer, ISI marked, 1000 Litre rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) fixed in position including PTMT 25mm bore ball valve high pressure with epoxy coated aluminium rod and high density plastic ball , two Nos new tank nipples of PTMT material 20/25mmdia as required including dismantling exisitng tanks of any size and any type complete all as specified & directed. |
| 98 | S&F Aluminium sliding windows shutters powder coated (minimum thickness of powder coating 50 micron)including powder coated main frame,three track (two for glazed and one for wire mesh) without sash barsincluding necessary jointing cleats, glazing clips, EPDM rubber packing, powder coated aluminium snap beading, screws, wheels, locking arrangments, suitable handles for sliding purpose, 4mm thick dark black tint plain glass and stainless steel wire mesh of dia 0.36mm and 1.40mm width of aperature, silicon chemical filling at gaps between section frame and wall surfaces completeallas specified and directed. |
| 99 | S&F sheet glass, ordinary quality, in squares, pane of 4mm thickness not exc 0.5 Sqm each with solar control film 50micron reflective type sticked to glass pane completeallas specified and directed. |
| 100 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm² , modules of elasticity 900 N/mm²and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed. Make: Rajshri Plastiwood or approved make |
| 101 | S&Fstainless steel handles 100mm size, D type dotted for kitchen/cup board cabinet shutters complete all as specified and directed. |
| 102 | S&Fdrawer ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 Kgs complete all as specified and directed. |
| 103 | S&Fmild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate of soft closing hydraulic pattern including welding to frame as required complete all as specified & directed. |
| 104 | M&L for preparation of old decorated painted wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint duly filled the voids with enamel based putty complete all as specified & directed. |
| 105 | M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint duly filled the voids with enamel based putty complete all as specified & directed. |
| 106 | S&Fin repairs25mm dia decorative type stainless steel curtain rods with decorative type including fixing end brackets, middle brackets , stops, etc. complete all as specified & directed. |
| 107 | S&Fwindow guard bars, hold fasts of plain/square conforming to Fe-290, Gde E-165 and fixed in walls of any description including bed blocks cutting, angle iron/flat iron frame of appd design and similar articles complete all as specified & directed. |
| 108 | M&L for preparation of new steel surfaces and applyingtwo coats synthetic enamel paint over a coat red oxide Zinc chromate primer over 10cm in width or girth, not otherwise describedcomplete all as specified & directed. |
| 109 | M&L for two coats of oil bound distemper over a coat of primer on walls, pillasters, cornices, etc., on newly plastered surfaces using spunge roller including one coat of primer over 2mm thick wall care putty in two coats complete all as specified & directed. |
| 110 | M&L for three coats of white washon newly plasterd ceiling surfaces including necessary filling of voids with wall care putty complete all as specified & directed. |
| 111 | M&Lfor applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed. |
| 112 | M&Lfor preparing, washing, rubbing down and stopping of distempered surface and complete removal of existing treatment and painted surfaces and applying two coats of oil bound distemperusing spunge roller including one coat of primerover 2mm thick wall care putty in two coats on walls, pillasters, cornices etc, all as specified & directed. |
| 113 | M&Lpreparing, washing, rubbing down and complete removal of existing treatmentfor applying twocoats ofacrylic emulsion paintof Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on old decorated surfacesofwalls including necessary filling of voids with wall care putty complete all as specified & directed. |
| 114 | S&FGI wire netting 0.90mm dia and 12mm square mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting, waste and cutting in plaster, concrete/stone surafce in patches complete all as specified & directed. |
| 115 | M&L for 50mm bore dia high density polyethylene pipes (HDPE) and fittings of pressure rating 6kgf/cm² fixed complete to walls, ceilings or in floors as drain out pipe etc., including necessary cutting and chasing in wall or floor of any description complete all as specified & directed. |
| 116 | S&F20mm thick pre-polished (table rubbed and polished) machine cut Granite stone work (of any type & size)in steps(treads), window/door-cills, cooking platforms, wash hand basin counter and like bedded and jointed with grey cement slurry with 20mm thick cement mortar (1:4) including pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work complete all as specified & directed. |
| 117 | S&F20mm thick pre-polished (table rubbed and polished) machine cut Granite stone work (of any type & size)in steps(risers), jambs, pillars, dado/skirting and like laid over cement screed bedded with 15mm thick cement mortar (1:4) and jointed with grey cement slurryincluding pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work complete all as specified & directed. |
| 118 | S&Fin repairs20mm diaBall valves high pressure of PTMT with epoxy coated Aluminiumrod& high density plastic ball screwed for iron/CPVC/PPR pipe and fixed complete all as specified & directed. |
| 119 | S&Fin repairs25mm diaBall valves high pressure of PTMT with epoxy coated Aluminiumrod& high density plastic ball screwed for iron/CPVC/PPR pipe and fixed complete all as specified & directed. |
| 120 | M&L for full round and polished moulding (as per main stone polish) to edges of stone slabs upto 20mm thick, such as in window cill, jambs, counters, steps etc. and of other similar situations complete all as specified & directed. |
| 121 | S&Fin repairsfancy swan neck Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified & directed. |
| 122 | Supply, hoisting and fixing of tripple layer, ISI marked, 500 litre rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) fixed in position including two Nos PTMT/UPVC tank nipple and25mm bore PTMTball valve high pressure with epoxy coated aluminium rod and high density plastic ball including dismantling exisitng water tanks of any size and and any description complete all as specified & directed. |
| 123 | S&F in repairsHealth faucet (ABS Body) chromium plated suitable for 15 mm bore dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete as specified and directed. |
| 124 | S&Ffactory made uPVC colour sliding window three track,area of each window not exceeded 2 Sqm,made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm ). Window profile with hollow section with multi chamber. Frame (90mm x 42.5mm), sliding sash (54mm x 32mm). Sliding mesh Sash (54mm x 32mm) Sliding interlock (One vertical length in each shutters) (30mm x 35.50mm), Glazing bead (22mm x 14.5mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 +0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (18mm x 10mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (touch lock of Zinc alloyed (white powder coated), steel roller system. The rates includes fiber mesh and 4mm thick frosted toughned glass.. Note: The unit rate quoted by contractor includes all other connected accessories. Net Opening will be measured for payment purpose. |
