Tender For Repairing Of 10/16 Kva Alu., 25 Kva Alu., 63 Kva Alu., 100 Kva Alu., 100 Kva Cu., 160 Kva Alu., 250 Kva Alu., 250 Kva Cu., 400 Kva Cu., 630 Kva Cu., And 1000 Kva Cu., Wound Damaged Distribution Transformer At Workshop Sachaindi (Kanpur Nagar) U, Agra-Uttar Pradesh

TDR : 48854347

Tender Notice
BOQ

Expired

Agra , Uttar Pradesh

Tender Brief : Tender For Repairing Of 10/16 Kva Alu., 25 Kva Alu., 63 Kva Alu., 100 Kva Alu., 100 Kva Cu., 160 Kva Alu., 250 Kva Alu., 250 Kva Cu., 400 Kva Cu., 630 Kva Cu., And 1000 Kva Cu., Wound Damaged Distribution Transformer At Workshop Sachaindi (Kanpur Nagar) U

Document Fees
₹ 3540 /-

EMD
₹ 70000.0 /-

Tender Value
₹ 60 Lakhs /-

Submission Date
30-04-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	10/16 KVA Single Phase Alu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank.Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
2	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
3	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
4	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
5	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
6	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
7	Refiting/Replacement/Fixing of HT Bushings.
8	Refiting/Replacement/Fixing of LT Bushings.
9	Refiting/Replacement/Fixing of HT Bushing Rods.
10	Refiting/Replacement/Fixing of LT Bushing Rods.
11	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
12	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
13	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
14	Refiting/Replacement/Fixing of Arching Horns/Breather.
15	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
16	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
17	25 KVA Three Phase Alu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Removal of Old layers (Multilayers) of Top Cover Plate by welding/gas cutting after taking out the Tank at safe area. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
18	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
19	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
20	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
21	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
22	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
23	Refiting/Replacement/Fixing of HT Bushings.
24	Refiting/Replacement/Fixing of LT Bushings.
25	Refiting/Replacement/Fixing of HT Bushing Rods.
26	Refiting/Replacement/Fixing of LT Bushing Rods.
27	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
28	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
29	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
30	Refiting/Replacement/Fixing of Arching Horns/Breather.
31	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
32	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
33	63 KVA Three Phase Alu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Removal of Old layers (Multilayers) of Top Cover Plate by welding/gas cutting after taking out the Tank at safe area. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
34	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
35	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
36	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
37	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
38	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
39	Refiting/Replacement/Fixing of HT Bushings.
40	Refiting/Replacement/Fixing of LT Bushings.
41	Refiting/Replacement/Fixing of HT Bushing Rods.
42	Refiting/Replacement/Fixing of LT Bushing Rods.
43	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
44	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
45	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
46	Refiting/Replacement/Fixing of Arching Horns/Breather.
47	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
48	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
49	100 KVA Three Phase Alu./Cu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Removal of Old layers (Multilayers) of Top Cover Plate by welding/gas cutting after taking out the Tank at safe area. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
50	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
51	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
52	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
53	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
54	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
55	Refiting/Replacement/Fixing of HT Bushings.
56	Refiting/Replacement/Fixing of LT Bushings.
57	Refiting/Replacement/Fixing of HT Bushing Rods.
58	Refiting/Replacement/Fixing of LT Bushing Rods.
59	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
60	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
61	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
62	Refiting/Replacement/Fixing of Arching Horns/Breather.
63	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
64	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
65	160 KVA Three Phase Alu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
66	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
67	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
68	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
69	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
70	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
71	Refiting/Replacement/Fixing of HT Bushings.
72	Refiting/Replacement/Fixing of LT Bushings.
73	Refiting/Replacement/Fixing of HT Bushing Rods.
74	Refiting/Replacement/Fixing of LT Bushing Rods.
75	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
76	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
77	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
78	Refiting/Replacement/Fixing of Arching Horns/Breather.
79	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
80	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
81	250 KVA Three Phase Alu./Cu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
82	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
83	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
84	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
85	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
86	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
87	Refiting/Replacement/Fixing of HT Bushings.
88	Refiting/Replacement/Fixing of LT Bushings.
89	Refiting/Replacement/Fixing of HT Bushing Rods.
90	Refiting/Replacement/Fixing of LT Bushing Rods.
91	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
92	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
93	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
94	Refiting/Replacement/Fixing of Arching Horns/Breather.
95	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
96	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
97	400 KVA Three Phase Cu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
98	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
99	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
100	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
101	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
102	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
103	Refiting/Replacement/Fixing of HT Bushings.
104	Refiting/Replacement/Fixing of LT Bushings.
105	Refiting/Replacement/Fixing of HT Bushing Rods.
106	Refiting/Replacement/Fixing of LT Bushing Rods.
107	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
108	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
109	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
110	Refiting/Replacement/Fixing of Arching Horns/Breather.
111	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
112	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
113	630 KVA Three Phase Cu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
114	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
115	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
116	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
117	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
118	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
119	Refiting/Replacement/Fixing of HT Bushings.
120	Refiting/Replacement/Fixing of LT Bushings.
121	Refiting/Replacement/Fixing of HT Bushing Rods.
122	Refiting/Replacement/Fixing of LT Bushing Rods.
123	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
124	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
125	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
126	Refiting/Replacement/Fixing of Arching Horns/Breather.
127	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
128	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).
129	1000 KVA Three Phase Cu. Wound (Workshop SACHAINDI (KANPUR NAGAR)) -Dragging, Shifting, Handling ofDamageTransformer from stacking yard to Dismantling area.Draining of Oil into pit/drum. Opening of top cover plate by T&P or cutting of sealed Transformer top cover plate by chisel Hammer Process, taking out the core and coil assembly from the tank. Dismantling core and coil assembly. Assembly of displaced core and cleaning of dust and dirt by cotton waste and wooden dust from every leaf of laminations if required(Welding/Brazing/Gas Cutting/Wooden Dust required for this work shall be arranged by the contractor).
130	Making of L.V. Coils as per original design/design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
131	Making of HV Leg coils of same size and dimensions as old one or design approved by concern JE/AE (Using either new coil or reconditioning old coil as per technical conditions of old coil).
132	Assembly of core and coils and fitting of other parts requiring replacements such as press board etc. Making supports between adjacent section by insulation spacers barriers etc. and tapping etc (Brazing/Soldering required, shall be arranged by the contractor). Shifting and keeping the assembled core and coils etc. In OVENfrom the repairing and assembly place.
133	Cleaning of tank in cleaning yard.Repairing of burst body & radiator properly with welding including repairing of bended base channel.Painting of inner side of transformer tank and channels with heat proof zinc chromate paint of good quality.(Berger, Nerolac, Jenson & Necholson etc) Paint material shall be provided by contractor at his own cost.
134	Dragging out clean empty tank from yard to repairing hall. Taking out assembled core and coils assembly from the \"OVEN\" after proper megger value and shifting to repairing hall. (Meggar will be arranged by the contractor at his own cost.). Retanking ofcomplete assembly into painted tank andProper tightening of the assembly in the tank safely by using nut bolts and spring washer of good quality, Fitting of all accessories ofthe transformer including fixing of pressure release valve/vent pipe and filling of oil in transformer (Vent Pipe will be arranged by the contractor at his own cost.). Punching of unique no. on MS plate 100x50x3 mm. size & Welding of MS Plate on Transformer Body containing following information:- Uniqe Number, Capacity (MS Plate & Punching Machine shall be provided by contractor).
135	Refiting/Replacement/Fixing of HT Bushings.
136	Refiting/Replacement/Fixing of LT Bushings.
137	Refiting/Replacement/Fixing of HT Bushing Rods.
138	Refiting/Replacement/Fixing of LT Bushing Rods.
139	Refiting/Replacement/Fixing of HT Gasket/Oil Seal for all phase.
140	Refiting/Replacement/Fixing of LT Gasket/Oil Seal for all phase.
141	Refiting/Replacement/Fixing of Top Cover Plate Gasket with typing of top cover plate by using nut bolt & washer.
142	Refiting/Replacement/Fixing of Arching Horns/Breather.
143	Painting of T/F outside with super enemal synthetic paint in two coats after de-rusting and providing primer of red oxide paint etc.(color should be decided by EE WS) Paint & Painting Material shall be arranged by the contractor. Painting of02 No. 50 mm. wide Green/Yellow/Orange/Red strip & writing name of workshopand ^^fo\|qr lEcU/kh f\"kdk;r gsrq Vksy Qzh ua0 1912 ij lEidZ djsaa**] Dragging of repaired T/F upto the test cabin /testing place and making full arrangement for the testing of transformer and their re-dragging to yard and its stacking at indentified place.
144	Daily cleaning of Workshop floor area, Open Shade and Open Area including the scrap material such as old paper, old pressboard, old cotton waste etc. (Wood dust, Sweeper, other required man power and T&P shall be arranged by the contractor).

Also Visit

Tenders

Uttar Pradesh Tenders

Electrical Industry Tenders

Transformers Tenders

Distribution Transformer Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Repairing Of 10/16 Kva Alu., 25 Kva Alu., 63 Kva Alu., 100 Kva Alu., 100 Kva Cu., 160 Kva Alu., 250 Kva Alu., 250 Kva Cu., 400 Kva Cu., 630 Kva Cu., And 1000 Kva Cu., Wound Damaged Distribution Transformer At Workshop Sachaindi (Kanpur Nagar) U, Agra-Uttar Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Repairing Of 10/16 Kva Alu., 25 Kva Alu., 63 Kva Alu., 100 Kva Alu., 100 Kva Cu., 160 Kva Alu., 250 Kva Alu., 250 Kva Cu., 400 Kva Cu., 630 Kva Cu., And 1000 Kva Cu., Wound Damaged Distribution Transformer At Workshop Sachaindi (Kanpur Nagar) U, Agra-Uttar Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us