|
| 1 | ALL THE RATES IN THIS BOQ ARE WITHOUT GST. GST SHALL BE PAID EXTRA AS PER PREVAILING RATES. |
| 2 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture\"s specification and direction of engineer in charge all complete.66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm. Actual area of one side wall shall be measured for payments. |
| 3 | Extra for providing 12mm Calcium silicate boards on both side of wall in place of 8mm calcium silicate boards in item ( Cost of 8mm already measured in above Item, cost of additional thickness shall be paid in this item). Actual area of one side wall shall be measured for payments. |
| 4 | Providing and fixing rockwool infill thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.Actual area of one side wall shall be measured for payments. |
| 5 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 crush sand) |
| 6 | Door Frame :Woodwork for wordrobe, wall cabinates , wall paneling, door frames etc by providing and fixing 18mm thick MR grade plywood duly machine pressed laminated with 1mm thick face decorative laminate of approved brand and manufacture and balance laminate shall be 0.8mm thick laminate of required shade with all exposed side edges shall be sealed with 2mm thick PVC edge banding (Rehau or equivalent) in modesty panels, side panels and storages etc. complete as per specification and direction of the Engineer in charge. Quoted rate shall be screws, glue, edge binding tape etc complete. Approved Makes Marino/Kitply/Century/Greenply |
| 7 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 8 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. Thickness of Laminate shall be 1mm. |
| 9 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 10 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square |
| 11 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Approved Make Hafele/Hettich/Godrej |
| 12 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm Approved Make Hafele/Hettich/Godrej |
| 13 | Providing and fixing concealed type aluminium die cast body tubular type universal hydraulic door closer (having brand logo embossed on the body, door weight minimum 60 kg and door width upto 1200 mm), with necessary accessories and screws etc. complete. Quoted rate shall be including chasing of as per OEM specifications and fixing of door closer. Approved Make Dorset/Ozone/Hettich/Yale |
| 14 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 15 | Providing and applying two or more coats of Water based Luster paint on wall and ceiling including two coat of approved primer on wall and ceiling with roller finish including preparation of surface by crack filling with expandable specialized crack filler, sand papering and applying primer, 1mm gypsum putty in line and level to all surface in line and level, two or more coat Paint on complete surface so as have and even and smooth surface, scaffolding all leads and lifts, labour , removal of existing old paint scraping, making surface ready for putty and cost of materials complete as per direction of Engineer-in-charge. Quoted rate shall be including expandable acrylic mortar in the cracks to prevent opening of cracks after painting in internal walls at any heights with Sika cracksil Acrylic paste / Dr.fixit crack-X paste /Dulux crack fill (ready to use paste) prepare surface by cleaning (Rate is inclusive of cost of all operations, material labour, all taxes, GST , etc. and nothing extra shall be payable). |
| 16 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 17 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminum (minimum thickness of powder coating 50 micron) For Fixed portion , Quoted rate shall be including GST , transportation , lead , lift ,wastage, scaffolding etc. complete. Nothing extra shall be paid separately. |
| 18 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Quoted rate shall be including expandable fastners as per approved design. Approved Make : RINL / JSW / TATA / SAIL/APPOLO |
| 19 | Steel work in built up tubular (round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. Approved Make : RINL / JSW / TATA / SAIL/APPOLO |
| 20 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. |
| 21 | Painting G.I./MS pipes/MS structural members and fittings with synthetic enamel white paint with two coats over already priming coat, approved make. For MS members up to size of 75X75 or 75mm dia. Actual length of alround external painting of member shall be measured for the payments. |
