Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 22-05-2025 | CORRIGENDUM III | Date | 28-05-2025 |
| 2 | 16-05-2025 | CORRIGENDUM II | Technical Bid | 21-05-2025 |
| 3 | 15-05-2025 | CORRIGENDUM I | Date | 21-05-2025 |
| Sl. No. | Item Description |
| 1 | ELECTRICAL WORKS |
| 2 | Design, Engineering and Supply of free standing, floor mounted, fixed type Uninterruptable Power Supply (UPS) System suitable for operation at indoor siteconditions along with battery banks (Ni-Cd Battery) and integrated system comprisingstatic rectifiers, battery charger, cell booster suitable for battery AH, accessories forbattery set, IGBTs, static inverters, static switches, manual by pass switch,IsolationTransformer, voltage stabilizer in bypass, isolating and protection devices and allother equipment/ accessories as required for completeness of the system whetherspecifically mentioned herein or not, but necessary for completeness and satisfactoryperformance of the system along with necessary control, metering and protectionequipment conforming to EIL specification 6-51-0017, 6-51-0047 & IS/IEC, etc.Supply of interconnecting cables between all equipments of UPS system (Between UPS,ACDB, Battery, battery charger and all other equipment supplied as a part of this UPS),commissioningspares, special tools & tackles, all labour and materialsas perapproved drawings, specifications, job specification, datasheet, instruction to vendoretc.of this tender and directions of Engineer-in-Charge. |
| 3 | 240V, 150 kVA, SPN AC UPS with bypass as per sketch-1 of 6-51-0017 |
| 4 | Cell Booster of adequate rating suitable for battery AH Capacity for UPS |
| 5 | 1x100% Ni-Cd Battery Bank for 30 Min backup with all accessories & battery isolator |
| 6 | Supply of240V, 800A,TPN, indoor fixed type, 25kA (min) for 1 Sec. Al. Bus-bar switch board, single front, free standing floor mounted,bottom cable entry, metalenclosed switchboards suitable for operation at indoor site conditionswith followingfeederscomplete withmeters, alarms, controls, protectionsetc. as per tenderSpecification 6-51-0017, job specification, hard-ware datasheets, componentdatasheet, other codes and standards attached or referred, including supply of allcommissioning spares,special tools and tackles & documentation, includingtransport, all labor and materials,asperapproveddrawings, specifications of thistender and directions of Engineer-in- Charge, complete in all respects. |
| 7 | 240 V, 800A MCCB incomer with mechanical interlock |
| 8 | 240 V, 63 AFeeder with 10kVA 240/240V Isolation Transformer along with 63A HRC Fuse on primary side of isolation transformer and 63 A Isolator & semi conductor fuseon secondary side of isolation transformer along with indication lamps |
| 9 | 240 V, 32 AFeeder with 5kVA 240/240V Isolation Transformer along with 32A HRCFuse on primary side of isolation transformer and 32 A Isolator & semi conductor fuseon secondary side of isolation transformer along with indication lamps |
| 10 | ROOFTOP SOLAR PHOTOVOLTAIC SYSTEM |
| 11 | Design, Engineering, Supply of grid connected rooftop solar photovoltaic power system with minimum generation output of minimum 125 kWp at the point ofcommon coupling with Owners switch board in Admin building. Supplied solar systemshall comprise but not limited to solar PV modules including mounting frames,structures, array foundation, module inter connection etc,Array Junction boxes, MainJunction boxes and Fuse boxes / circuit breakers, Power Conditioning Units (PCU), ACpower evacuation panels with bus bars and circuit breakers, Metering and protection /Isolation systems, MV Power and Control Cables including end terminations,cabletrays, supports & accessories, Galvanized steel conduits & accessories, PVC pipes,ferrules, lugs, glands, terminal blocks, galvanized sheet steel junction boxes, cablefixing clamps, nuts and bolts, Steel materials for field fabrication etc, otheraccessories for both AC & DC power as required for interconnection betweencontractor supplied equipment, Earthing system for PV Array, DC power system, ACpower system equipment, PCU etc., Lightning protection system, Data acquisition andmonitoring system with remote monitoring facilities etc. as per EIL standardspecification No. 6-51-0022 including all labour and materials, as per approveddrawings, specifications, drawings of this tender and directions of Engineer-inCharge. |
| 12 | Design, Engineering, Supply of grid connected rooftop solar photovoltaic powersystem on parking area with minimum generation output of minimum 60 kWp at thepoint of common coupling with Owners switch board in Admin building (Distancebetween admin building and parking area shall be 150m tentatively). Supplied solarsystem shall comprise but not limited to solar PV modules including mounting frames,structures, array foundation, module inter connection etc,Array Junction boxes, Main Junction boxes and Fuse boxes / circuit breakers, Power Conditioning Units (PCU), ACpower evacuation panels with bus bars and circuit breakers, Metering and protection /Isolation systems, (All equipment including PCU and AC evacuation panel shall beoutdoor type), MV Power and Control Cables including end terminations,cable trays,supports & accessories, Galvanized steel conduits & accessories, PVC pipes, ferrules,lugs, glands, terminal blocks, galvanized sheet steel junction boxes, cable fixingclamps, nuts and bolts, Steel materials for field fabrication etc, other accessories forboth AC & DC power as required for interconnection between contractor suppliedequipment, Earthing system for PV Array, DC power system, AC power systemequipment, PCU etc., Lightning protection system, Data acquisition and monitoringsystem with remote monitoring facilities etc. as per EIL standard specification No. 651-0022including all labour and materials, as per approved drawings, specifications,drawingsof this tender and directions of Engineer-in-Charge. |
| 13 | Installation, Testing and commissioning of grid connected rooftop solar photovoltaicpower system as per complete MR item 01EE.MA03.01 including Earthing system,Lightning protection system, configuration of Data acquisition and monitoring systemwith remote monitoring facilities etc andlaying and termination of cable within allequipments supplied as a part of this solar system and from PCU/AC Power evacuationpanel to 415V Main distribution board in admin building and all other items as per EILstandard specification No. 6-51-0022 including all labour and materials, as perapproved drawings, specifications, drawings of this tender and directions of Engineerin-Charge. |
| 14 | Installation, Testing and commissioning of grid connected rooftop solar photovoltaicpower system as per complete MR item 01EE.MA03.02, including Earthing system,Lightning protection system, configuration of Data acquisition and monitoring systemwith remote monitoring facilities etc and laying and termination of cable within allequipments supplied as a part of this solar system and from PCU/AC Power evacuationpanel to 415V Main distribution board in admin building (tentative distance of 150m)and all other items as per EIL standard specification No. 6-51-0022 including alllabour and materials, as per approved drawings, specifications, drawings of thistender and directions of Engineer-in-Charge. |
| 15 | I/T/C of UPS System |
| 16 | Installation, testing and commissioning of Uninterruptable Power Supply (UPS) System along with associated battery banks (Ni-Cd Battery), battery charger, cell booster andall equipment supplied as a part of UPS system as per item 01EE.MA01 along withaccessories of complete equipment, including transportation from store/yard to site atthe place of installation, lifting the panels by deployment of tyre mounted hydraulictrollies, unpacking, assembly, including mounting and wiring of loose parts suppliedby equipment vendor, interconnection of shipping sections and requisite inter-panelwiring between shipping sections, including supply of all wiring materials, installationon foundations or fixing to wall or steel structures, aligning, levelling, grouting,testing and calibration of relays and meters etc., and filling with electrolyte inbatteries, aligning, levelling, grouting, assembly of battery racks, fixing of inter-cellconnectors etcincluding all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge |
| 17 | Supply of415V, 125A,TPN, indoor draw out type, 25kA (min) for 1 Sec. Al. Bus-barswitch board, double front, free standing floor mounted,bottom cable entry, metalenclosed switchboards suitable for operation at indoor site conditionswith followingfeederscomplete withmeters, alarms, controls, protectionsetc. as per tenderSpecification 6-51-0018, job specification, hard-ware datasheets, componentdatasheet, other codes and standards attached or referred, including supply of allcommissioning spares,special tools and tackles & documentation, includingtransport, all laborand materials,asperapproveddrawings, specifications of thistender and directions of Engineer-in- Charge, complete in all respects. |
| 18 | 415 V, 125A MCCB incomer as per datasheet B378-999-16-50-DS-1814 along withMechanical Interlock |
| 19 | 415 V, 125A MCCB buscoupler as per datasheet B378-999-16-50-DS-1814 |
| 20 | 415 V, 63A MCCB feeder as per datasheet B378-999-16-50-DS-1821 |
| 21 | EV Charging Stations |
| 22 | Supply of IP-55 and IK-10 EV charging station rated for 230V, 16A, 3.3kWsuitable for operating at a temperature of 40degrees and complete with attached socket suitable for bike charging along with lamps for indication, emergency stop pushbutton, earthleakage protection, under voltage protection, access control through RFID/ mobile appand suitable for installation on wall/ channel/ column, capable for cable terminationincluding all labor and materials complete as per approved drawings, job & standardspecification attached with this tender, latest IS and IEC requirementsand directionsof the engineer-in- charge |
| 23 | Supply of IP-55 and IK-10 EV charging station rated for 230V, 32A, 7.4kWsuitable foroperating at a temperature of 40degrees and complete with attached Type-2connector cable of 5m length suitable for car charging along with lamps for indication,emergency stop pushbutton, earth leakage protection, under voltage protection,access control through RFID/ mobile app and suitable for installation on wall/channel/ column, capable for cable termination including all labor and materialscomplete as per approved drawings, job & standard specification attached with thistender, latest IS and IEC requirementsand directions of the engineer-in- charge |
| 24 | Installation, testing and commissioning of IP-55 and IK-10 EV charging station ratedfor 230V, 16A, 3.3kW along with installation on wall/ channel/ column, cabletermination, configuration for access the station including all labor and materialscomplete as per approved drawings, job & standard specification attached with thistender, latest IS and IEC requirementsand directions of the engineer-in- charge |
| 25 | Installation, testing and commissioning of IP-55 and IK-10 EV charging station ratedfor 230V, 32A, 7.4kW along with installation on wall/ channel/ column, cabletermination, configuration for access the station including all labor and materialscomplete as per approved drawings, job & standard specification attached with thistender, latest IS and IEC requirementsand directions of the engineer-in- charge |
| 26 | TRANSFORMERS |
| 27 | Supply of dry type transformers with accessories,including nuts and bolts etc., as per EIL standard specification No. 6-51-0042, including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-in-Charge |
| 28 | 2 Winding Dry type transformers. .415 kV/ .415 kV50 kV·A |
| 29 | Installation, testing and commissioning of dry transformer of following rating,including transportation from store/yard to site at the place of installation, unpacking,positioning in place, site assembly of loosely furnished accessories, connection ofauxiliary circuits,including fixing of nuts and bolts etc., including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge |
| 30 | 2 Winding Dry type transformers. .415 kV/ .415 kV50 kV·A |
| 31 | SWITCHBOARDS / UPS / VSD / BATTERY CHARGERS / PANELS |
| 32 | Supply of following indoor drawout type MV switchboard as per EIL specification No. 6 -51-0018, including all labour and materials, as per approved drawings, specificationsof this tender and directions of Engineer-in-Charge. |
| 33 | 415 V, 3 Phase, TPN, 50Hz,160A, 25kA (1Sec) switchboardwith 1 no. 160A incomerMCCB incomer and 10 nos. 63A outgoing MCCB + ELCB feeders. Incomer shall havevoltmeter and ammeter with selector switches and outgoing feeders shall haveammeter with selector switch |
| 34 | Installation, testing and commissioning of switch-boards, relay and control panels,annunciation panels, UPS system, battery chargers, distribution boards, cubicles withelectrical equipment, VSD panels, misc .electrical panels etc., including transportationfrom store/yard to site at the place of installation, lifting the panels by deployment oftyre mounted hydraulic trollies, unpacking, assembly, including mounting and wiringof loose parts supplied by equipment vendor, interconnection of shipping sectionsand requisite inter-panel wiring between shipping sections, including supply of allwiring materials, installation on foundations or fixing to wall or steel structures,aligning, levelling, grouting, testing and calibration of relays and meters etc.,including all labour and materials, as per approved drawings, specifications of thistender and directions of Engineer-in-Charge. |
| 35 | Weight of the Unit upto 100 kg |
| 36 | Weight of the Unit from 101 upto 500 kg. |
| 37 | Weight of the Unit from 501 upto 1000 kg. |
| 38 | Weight of the Unit from 1001 upto 1500 kg. |
| 39 | Weight of the Unit from 1501 upto 3000 kg. |
| 40 | MISCELLANEOUS CONTROL GEAR |
| 41 | Installation, testing and commissioning of miscellaneous surface mounted industrial/FLP control gear such as lighting/power panel, push button stations, motorstarter, communication equipment, junction boxes, panels, plugs, sockets, includingsupply of necessary hardware, touch up painting including supply of paint, includingtransportation from store/yard to site at the place of installation, unpacking,(excluding fixing of cable glands and cable terminations),including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 42 | Weight of the unit up to 5 kg. |
| 43 | Weight of the unit above 5 kg. but upto 20 kg. |
| 44 | Supply of Industrial, weather proof type Push Button stations as per EIL specification No. 6-51-0014, as per approved drawings, specifications of this tender and directionsof Engineer-in-Charge. |
| 45 | With start and stop (latching type) push buttons. |
| 46 | PLUGS, SOCKETS AND JUNCTION BOXES |
| 47 | Supply of following types of FLP (II C) and WP sockets, plugs and handlamps as per EIL specification No. 6-51-0021,including all labours and materials, as per approveddrawings, specifications of this tender and directions of Engineer-in-Charge. |
| 48 | 240 V, 15 A, 3 pin socket. |
| 49 | 240 V, 15 A, 3 pin Plugs for item no. 01EE.1060.30.70 |
| 50 | SAFETY EQUIPMENT |
| 51 | Supply and installation of the following, including the supply of necessary clamps, bolts, rawl plugs etc., breaking and making good of walls, if required, mounting,including all labour and materials, complete and as per applicable standards and CEAGuidelines and as per directions of Engineer-in-Charge. |
| 52 | True RMS Digital Multimeter with Display of up to 3 digits of decimal |
| 53 | Electrical Protection suit |
| 54 | Shock hazard charts complete with frame and glass. |
| 55 | First Aid Boxes. |
| 56 | Sand buckets with stand (Each with at least 3 sand buckets). |
| 57 | Supply and laying of 900 mm wide safety insulation mats complying to IS-15652, of following grades required for maintenance of electrical equipment in substation,including cutting to required shape in running length, including all labour andmaterials, as per applicable Indian or International standards and CEA Guidelines andas per directions of Engineer-in-Charge. |
| 58 | 3.3 kV grade |
| 59 | Supply of following items as per applicable Indian standards/CEA Guidelines. |
| 60 | Rubber hand gloves (11 kV grade). |
| 61 | Supply and application/installation of epoxy based insulation coating with breakdown voltage as per IS, suitable for system voltage as marked and shall be suitable forinstallation on concrete flooring of substation in airconditioned/non-airconditionedarea, having smooth finish, including all labour and materials, complete as perapproved drawings, job & standard specification attached with this tender anddirections of the engineer-in- charge |
| 62 | For highest systen voltage of 1.2kV |
| 63 | SUPPLY OF MV CABLES |
| 64 | Supply of 1100 V grade, Copper Conductor,XLPE insulated and armoured, cables offollowing sizes as per EIL standard specification No. 6-51-0051, data sheets,specifications of this tender and directions of Engineer-in-Charge. |
| 65 | 3 C x 2.5 sq. mm |
| 66 | 3 C x 4 sq. mm |
| 67 | Supply of 1100 V grade, Copper Conductor, Individual pair shielded & Overallshielded, twisted pair/triad, XLPE insulated, Armored, FRLS outer-sheathed cables offollowing sizes as per EIL standard specification No. 6-51-0052, data sheets,specifications of this tender and directions of Engineer-in-Charge. |
| 68 | 2 Pair x 1.5 sq. mm |
| 69 | 5 Pair x 0.9 mm dia |
| 70 | Supply of 1100 V grade, Copper Conductor, Individual pair shielded & Overallshielded, twisted pair/triad, XLPE insulated, Unarmored, FRLS outer-sheathed cablesof following sizes as per EIL standard specification No. 6-51-0052, data sheets,specifications of this tender and directions of Engineer-in-Charge. |
| 71 | 2 Pair x 1.5 sq. mm |
| 72 | 5 Pair x 0.9 mm dia |
| 73 | LAYING OF CABLES |
| 74 | Laying of cables of different voltage grade and types of the following overall diameters in ready trays/trenches/ supported on structure/pull through pipes including supplyand fixing of stainless steel strip number tags, supply and applying of fireproofingpaint to meet OISD requirement and as per IEC-60331 (for 1m length nearterminations), supply and fixing of GI saddles & saddle bars, trefoil clamps (for singlecore cables) etc., including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge |
| 75 | Cables with OD upto 20 mm. |
| 76 | Cables with OD above 20 mm but upto 30 mm. |
| 77 | Cables with OD above 30 mm but upto 40 mm |
| 78 | Cables with OD above 40 mm but upto 50 mm. |
| 79 | Cables with OD above 50 mm but upto 60 mm. |
| 80 | END TERMINATIONS |
| 81 | Termination of XLPE insulated armoured power cables (up to 1100 V grade) and connection of leads excluding the supply of cable glands and lugs but including fixing of cable glands, supply and fixing of PVC shrouds for outdoor terminations,cutting and stripping of cable insulation, crimping the lug on to the conductor,clamping of the cable-cores, marking with wire number, ferrules etc., including alllabour and materials, as per approved drawings, specifications of this tender anddirections of Engineer-in-Charge. |
| 82 | Cables with OD upto 20 mm. |
| 83 | Cables with OD above 20 mm but upto 30 mm. |
| 84 | Cables with OD above 30 mm but upto 40 mm. |
| 85 | Cables with OD above 40 mm but upto 50 mm. |
| 86 | Cables with OD above 50 mm but upto 60 mm |
| 87 | G.I. & PVC PIPES |
| 88 | Supply and laying of following sizes ofG.I. Pipes (medium) in required length fixed on steel, concrete or similar structure, laid in trenches, ready to be buried in concreteincluding cutting, threading, bending and similar works, supply of clamps, small ironstructures, spacers and installation of seats, plugs, bushings etc., small civil works,including all labour and materials, as per approved drawings, specifications of thistender and directions of Engineer-in-Charge |
| 89 | 50 mm NB. |
| 90 | 100 mm NB. |
| 91 | 150 mm NB. |
| 92 | STRUCTURAL STEEL |
| 93 | Supply and installation of push button station supports complete with base plate, foundations bolts, grouting and painting(as per Table-10 ofspecification 6-79-0020suitable for highly corrosive environment) etc., including all labour and materials, asper approved drawings and directions of Engineer-in-Charge. |
| 94 | As per std. 7-51-0307 |
| 95 | CABLE - TRAYS |
| 96 | Supply and installation of prefabricated hot dip galvanised steel cable trays, fabricated out of hot rolled sheet steel with rigid welded construction ladder type with a rung asper std. 7-51-0333, of approved make and cable tray fittings, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 97 | 450 mm wide Straight run cable tray. |
| 98 | Horizontal bends for 450 mm wide tray with 1000 mm bending radius. |
| 99 | Vertical outside bends for 450 mm wide tray with 1000 mm bending radius |
| 100 | Tee Joints for 450 mm wide tray with 1000 mm bending radius. |
| 101 | Supply and installation of following galvanised slotted channel trays of 2 mmthickness and 50 mm high for supporting cables, including all labour and materials, asper approved drawings, specifications of this tender and directions of Engineer-inCharge. |
| 102 | 100 mm wide. |
| 103 | Providing and fixing 1.6mm thick Gl fabricated raceways in partition include providing removable 3mm thick cover with knockout holes and fixing accessories, earthingconnectivity for the complete length, including floor / wall supports, access boxes asper specification and cross over as per site requirement. |
| 104 | 300X40X1.6/3MM |
| 105 | 200X40X1.6/3MM |
| 106 | Providing and fixing 2 mm thick G.I. fabricated junction box in raceways includeproviding removable 3mm thick cover with knockout holes and fixing accessories,earthing connectivity for the box, including floor / wall supports, access boxes as perspecification and cross over as per site requirement |
| 107 | 300X300X50X2/3MM (with SS Cover) |
| 108 | 200X200X50X2/3MM (with SS Cover) |
| 109 | CABLE GLANDS |
| 110 | Supply of nickel-plated, flame proof IIC double compression type brass cable glands, suitable for out door terminations of armoured PVC cables of following overalldiameter (excluding termination and connection of cables), including all labour and materials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 111 | Cables with OD upto 20 mm. |
| 112 | Supply of nickel plated brass single compression cable glands of following overall diameter (excluding termination and connections of cables), including drilling ofsuitable holes in equipments for fixing purposes etc., including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 113 | Cables with OD upto 20 mm |
| 114 | Cables with OD above 20 mm but upto 30 mm. |
| 115 | Cables with OD above 30 mm but upto 40 mm. |
| 116 | Cables with OD above 40 mm but upto 50 mm. |
| 117 | Cables with OD above 50 mm but upto 60 mm. |
| 118 | FIRE PROOFING OF CABLES |
| 119 | Fire proofing of cables including supply of all fire proofing paint, including all labour and materials, as per specifications of this tender and directions of Engineer-inCharge.(Actual area of surface painted shall be measured). |
| 120 | LIGHTING POLES |
| 121 | Supply and installation of Lighting Poles for floor mounting as per std. 7-51-0201 along with Single overhang circular decorative arms of 1 mtr length one side. TheDecorative arm should support suspended mounting of the LED Drop Down Post Top.The circular arm should be properly welded to the pipe by means of 3 segments. Adecorative embellishment knob at the top of pole and a designer element shall beprovided on the arm for aesthetics and all civil works, excavation, foundation, disposalof surplus earth, providing shoring, strutting and dewatering if required and includingsupply of cement, steel, GI pipes, base plates, paint and all sundry materials as required, including painting, including supply and installation of control gearbox/junction box, cable termination upto lamp via junction box and all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 122 | Supply and installation of Lighting Poles for floor mounting as per std. 7-51-0201,including all civil works, excavation, foundation, disposal of surplus earth, providingshoring, strutting and dewatering if required and including supply of cement, steel, GIpipes, base plates, paint and all sundry materials as required, including painting,(excluding supply and installation of control gear box/junction box), but including alllabour and materials, as per approved drawings, specifications of this tender anddirections of Engineer-in-Charge. |
| 123 | Lighting poles including supply and connection of wires upto fixtures for safe areas. |
| 124 | Supply andinstallation of Poles for post top lantern as per std. 7-51-0210 with marshalling box, necessary wires/cable running from marshalling box to the lightingfixtures, cable termination and connection, fixing of cable glands and lugs, , includingall civil works, excavation, foundation, disposal of surplus earth, providing shoring,strutting and dewatering if required and supply of cement, steel, GI pipes, base plates,paint and all sundry materials as required, painting, including all labour and materials,as per approved drawings, specifications of this tender and directions of Engineer-inCharge. |
| 125 | Post top lantern. |
| 126 | HAZARDOUS AREA LIGHTING FIXTURES AND ACCESSORIES |
| 127 | Installation, connection, testing and commissioning of following types of flame proof/Div.2 lighting fixtures and accessories, including cable termination andconnection, fixing of cable glands, lugs, including supply of necessary hardwares,including transportation from store/yard to site at the place of installation, unpacking,including all labour and materials, as per approved drawings, specifications of thistender and directions of Engineer-in-Charge. |
| 128 | 3-way, junction box. |
| 129 | Supply of following FLP/Div.2 lighting fixtures complete with lamps, requisite FLPcable glands, plugs and necessary control gear as per EIL standard specification No. 6-51-0061, data sheet for lighting fixture schedule, including all albour and materials,specifications of this tender and directions of Engineer-in-Charge. |
| 130 | Type FLP-IIC-12 Fixtures. |
| 131 | SAFE AREA LIGHTING FIXTURES |
| 132 | Supply, installation, testing and commissioning of following energy efficient lighting fixtures and connecting to wiring junction box/marshalling box complete with lampsand necessary control gear including supply of all connected materials like flexibleconduit, clamps, supports, chains, anchor fastners, bolts, nuts and washers etc. asrequired, including supply and fixing of cable glands, lugs, including all labour andmaterials, as per approved drawings, data sheet for lighting fixture schedule, EILinstallation standards, specifications of this tender and directions of Engineer-inCharge. |
| 133 | Type LED 1 Fixtures. |
| 134 | Type LED 2 Fixtures. |
| 135 | Type LED 3 Fixtures. |
| 136 | Type LED 6 Fixtures. |
| 137 | Type LED IND-1 Fixtures. |
| 138 | Type LED IND-2 Fixtures. |
| 139 | Type LED RSD-10 Fixtures. |
| 140 | Type LED SFD-12 Fixtures. |
| 141 | Type LED BK-2 Fixtures. |
| 142 | Type LED ST-4 Fixtures. |
| 143 | Type LED FD-1 Fixtures |
| 144 | Type LED FD-2 Fixtures. |
| 145 | Type LED FD-9 Fixtures. |
| 146 | Type LED HB-1 Fixtures. |
| 147 | Type LED ADMIN1 Fixtures. |
| 148 | Type LED ADMIN2 Fixtures. |
| 149 | Type LED ADMIN3 Fixtures. |
| 150 | Type LED ADMIN4 Fixtures. |
| 151 | Type LED ADMIN5 Fixtures |
| 152 | Type LED ADMIN6 Fixtures. |
| 153 | Type LED ADMIN7 Fixtures. |
| 154 | Type LED ADMIN8 Fixtures. |
| 155 | Type LED ADMIN9 Fixtures |
| 156 | Type LED ADMIN10 Fixtures. |
| 157 | Type LED ADMIN11 Fixtures |
| 158 | Type LED ADMIN12 Fixtures. |
| 159 | Type LED ADMIN13 Fixtures. |
| 160 | Type LED ADMIN15 Fixtures. |
| 161 | Type LED ADMIN16 Fixtures. |
| 162 | Type LED ADMIN17 Fixtures. |
| 163 | Type LED ADMIN18 Fixtures. |
| 164 | Type LED ADMIN19 Fixtures |
| 165 | FANS AND EXHAUST FANS |
| 166 | Supply, installation, connection, testing and commissioning of following types of exhaust fans including supply of all necessary supports etc., including fixing of cableglands, lugs with BEE(Bureau of Energy Efficiency)rating of minimum 3 star includingall labour and materials and accessories like mounting frame, fixing bolt, wireguard/louvres etc., as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 167 | 300 mm dia., 1 phase, 900 rpm, wall mounting type epoxy painted exhaust fan with louvres. |
| 168 | 450 mm dia., 1 phase, 900 rpm, wall mounting type epoxy painted exhaust fan withlouvres suitable for Gas group IIC, temperature class T3. |
| 169 | Supply, installation, connection, testing and commissioning of 240 V AC, 1200 mmsweep ceiling fan with regulator (labeled as minimum 3-star by Bureau of EnergyEfficiency)including providing clamp/hook in RCC slab, if necessary, providing, fixing,ceiling, rose, wiring, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge. |
| 170 | SOCKETS / RECEPTACLES AND SWITCHES / MCB UNITS |
| 171 | Supply, installation, connection, testing and commissioning of following ratings of 240 V, single phase, sockets/receptacles and metallic outlet boxes as described belowincluding supply of all connected materials, including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 172 | 6 A, 5 pin plate type flush/ surface mounting sockets/receptacles |
| 173 | 16/6 A, 6 pin plate type flush/ surface mounting sockets/receptacles. |
| 174 | 20 A, 3 pin surface mounted industrial type switch socket with plug and sheet steel painted box. |
| 175 | 3 Nos. 16/6 A, 6 Pin sockets with 1 Nos. 15A, switch (Flush Mounted Switch + Socket) |
| 176 | Supply, installation, connection, testing and commissioning of following ratings of 240V, single phase switches/MCB units, including outlet boxes and associatedaccessories, including all labour and materials,as per approved drawings,specifications of this tender and directions of Engineer-in-Charge. |
| 177 | 5 A, plate type flush/surface mounted switches. |
| 178 | 15 A, plate type flush/surface mounted switches. |
| 179 | 32A, DP MCB unit in moulded case enclosure for window / split type air conditioner. |
| 180 | 20A, DP MCB unit in moulded case enclosure |
| 181 | JUNCTION BOXES (OUTDOOR / INDOOR TYPE) |
| 182 | Supply and installation of dust and vermin proof G.I. sheet steel (1.6 mm thick) junction box WP type suitable for outdoor/indoor installation with number of outgoingways as under, complete with PVC connectors, supply and fixing of cable glands,including supply of required size and number of terminals, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 183 | 4 way. |
| 184 | Supply and installation of dust and vermin proof G.I. sheet steel (1.6 mm thick) junction box suitable for indoor installation, complete with 15A, 20 terminals, supplyand fixing of cable glands for incoming cable and knock outs for conduit entry foroutgoing circuits, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge. |
| 185 | Junction box. |
| 186 | LIGHTING / POWER PANELS AND DISTRIBUTION BOARDS |
| 187 | Supply, installation, connection, testing and commissioning of Weather proof IP-55 safe area lighting/power panels along with GI canopy, surface/flush mounting type,wall mounting type in dust tight (with hinged cover) sheet steel enclosure having 4pole incomer and double pole MCB (9 kA type) for outgoing circuit control withcompletewiring, including cable termination, connection and fixing of cable glands,including all labour and materials, as per approved drawings, specifications of thistender and directions of Engineer-in-Charge. |
| 188 | 125 A, 2 Nos 4 pole incomer MCB isolator and 8 Nos. outgoingdouble poleMCBs +ELCB (32 A). |
| 189 | Supply, installation, connection, testing and commissioning of safe arealighting/power panels, surface/flush mounting type, wall mounting type in dust tight(with hinged cover) sheet steel enclosure having 4 pole incomer and single pole MCB(9 kA type) for outgoing circuit control with completewiring, including cabletermination, connection and fixing of cable glands, including all labour and materials,as per approved drawings, specifications of this tender and directions of Engineer-inCharge. |
| 190 | 40 A, 4 pole incomer MCB isolator and 6 Nos. outgoingsingle poleMCBs (upto 20 A). |
| 191 | 40 A, 4 pole incomer MCB isolator and 12 Nos. outgoingsingle poleMCBs (upto 20 A). |
| 192 | 63 A, 4 pole incomer MCB isolator and 18 Nos. outgoingsingle poleMCBs (upto 20A). |
| 193 | 63 A, 4 pole incomer MCB isolator and 6 Nos. outgoing32 A single poleMCBs. |
| 194 | Supply, installation, connection, testing and commissioning of following 415 V, TPN main distribution Board (MDB) wall mounting type, dust and vermin proof with TPNincomer with voltmeter and selector switch and outgoing feeders with suitable knockouts, fixing of cable glands, lugs, terminal connectors, suitable stud for earthing, including all labour and materials, as per approved drawings, specifications of thistender and directions of Engineer-in-Charge. |
| 195 | 100 A, incomer MCCB and 8 Nos. 40 A outgoing TPN MCBs |
| 196 | WIRING |
| 197 | Circuit wiring with 660 V grade, (sizes given below), FRLS PVC insulated copper wires in already laid surface/concealed conduit from lighting panel/power panel onwardsincluding the supply of wires, termination and connection, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 198 | 3 Nos x 1.5 sq. mm |
| 199 | 3 Nos x 2.5 sq. mm |
| 200 | 5 Nos x 1.5 sq. mm |
| 201 | 5 Nos x 2.5 sq. mm |
| 202 | 7 Nos x 1.5 sq. mm |
| 203 | 7 Nos x 2.5 sq. mm |
| 204 | 3 Nos x 4 sq. mm |
| 205 | 5 Nos x 4 sq. mm |
| 206 | Supply and laying of (surface type) approved make of black enamelled steel conduit of following diameter and associated fittings from lighting/power panel, telephone, firealarm/plant communication points etc., including supply of G.I. sheet steel junctionboxes with acrylic cover, pull wire, including all labour and materials,as per approveddrawings, specifications of this tender and directions of Engineer-in-Charge. |
| 207 | 25 mm diameter |
| 208 | 40 mm diameter |
| 209 | Supply and installation of 50 mm x 50 mm, (18 SWG) \"METSEC\" channel with removable cover, including supply of all connected hardware, supports, all labour and materials,as per approved drawings, specifications of this tender and directions of Engineer-inCharge. |
| 210 | Circuit wiring with 660 V grade (sizes given below) PVC insulated copper conductorwires in already installed metsec channel including the supply of wires, termination,connection and harnessing of wires etc., including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-in-Charge. |
| 211 | 1.5 sq. mm wires. |
| 212 | 2.5 sq. mm wires. |
| 213 | Supply and laying of (concealed type) PVC conduit of following diameter and associated fittings in brick walls, RCC slabs/ceilings for lighting/ power/telephone,fire alarm/plant communication points etc., including supply of G.I. sheet steeljunction boxes with acrylic cover, pull wire, making cuts and chasis in built up brickwork, RCC slabs/ceilings and making good the same, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 214 | 25 mm diameter. |
| 215 | 40 mm diameter |
| 216 | Circuit wiring in non-hazardous areas using (size given below), copper conductor,XLPE insulated, FRLS outer sleeve cables (third core for earthing),from lighting/power panel/distribution junction box, excluding the supply of cable, junction boxes andcable glands but including termination and connection, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 217 | 3 C x 2.5 sq. mm |
| 218 | 3 C x 4 sq. mm |
| 219 | Circuit wiring in hazardous areas using (sizes given below) copper conductor, XLPEinsulated, FRLS outer sleeve armoured cables (third core for earthing) fromlighting/power panel/distribution junction box onwards, excluding the supply ofcables, junction boxes and cable glands but including fixing of cable glands, supplyand fixing of clamps, cable terminations and connections, including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 220 | 3 C x 2.5 sq. mm |
| 221 | EMERGENCY LIGHTING |
| 222 | Supply, installation, connection, testing and commissioning of emergency lighting unit (min. 5W, 100 lumens output) fed by a self- contained battery rated for 2 hours andcharger operating on 240 V AC supply, including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-inCharge. |
| 223 | SENSORS |
| 224 | Supply, Installation, testing and commissioning of Sensor having both Passive Infrared(PIR) technology (occupancy) and smart day light sensing technology having highperformance along with necessary junction box, wiring, fixing arrangements andsupply of all connected materials, including programming at site, complete with alllabor and material as required as per specifications of this tender and directions ofEngineer-in-charge |
| 225 | EARTH ELECTRODES |
| 226 | Supply, installation, testing and commissioning of Maintenance free earth pit as per sketch B378SKand job Specification and all necessary materialsincluding excavation of earth pit, filling with earth enhancing compound, back filling,providing necessary brickwork, connections, including all labour and materials, as perapproved drawings, specifications of this tender and directions of EngineerinCharge |
| 227 | EARTH STRIPS |
| 228 | Supply, installation and connection of following GI earthing strip along the cable trenches or cable trays or fixing to walls or structures including welding at joints,providing anti-corrosive paint or bitumen and jute covering for welded portion,clamping and necessary hardware for connecting, etc., including all labour andmaterials, as per approved drawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 229 | 100 x 12 mm |
| 230 | 50 x 6 mm |
| 231 | 25 x 3 mm |
| 232 | Supply, installation and connection of following GI earthing strip buried individually at a depth of 500 mm including welding at joints, providing anti-corrosive paint orbitumen and jute covering for welded portion, clamping and necessary hardware forconnecting, excavation and refilling etc., including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-in-Charge |
| 233 | 100 x 12 mm |
| 234 | 50 x 6 mm |
| 235 | 25 x 3 mm |
| 236 | EARTHING CONNECTION |
| 237 | Connecting individual equipment to the earth strip or earth plate with following sizes of G.I. wire / G.I. wire rope including the supply of G.I. wire /G.I. wire rope, lugs,conductors, connecting to the G.I. strip or earth plate and necessary hardware forconnection, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge. |
| 238 | 3/8\" dia (10 mm) flexible rope |
| 239 | 5/8\" dia (16 mm) flexible rope |
| 240 | 8 SWG GI Wire. |
| 241 | EARTH PLATES |
| 242 | Supply, installation and connection of GI earth plates as per std. 7-51-0103, complete with anchor bolts, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge. |
| 243 | GI earth plate as per std. 7-51-0103 |
| 244 | TELEPHONE SYSTEM |
| 245 | Supply, installation, testing and commissioning ofIndoor Telephone Distribution J.B. made out of 2.03 mm (14 gauge) sheet steel, with one anti-rust coat of primer, withtwo finished coats of approved epoxy paint, with Krone type terminals with hingedlockable door, detachable gland plate at the bottom/top complete with terminationand connections of incoming/ outgoing cables, including all labour and materials, asper specifications of this tender and directions of Engineer-in-Charge. |
| 246 | TDJB Surface mounting type, suitable for 1 nos50 Pair incoming cable(s) and 50nos2 Pair outgoing cable(s) |
| 247 | TDJB Surface mounting type, suitable for 1 nos20 Pair incoming cable(s) and 2nos20 Pair outgoing cable(s) |
| 248 | Supply, installation, connection, testing and commissioning of following plug - in typesockets for Telephones extensions including supply of sheet boxes with coversconnection of socket and plug, including all labour and materials, as per approveddrawings, specifications of this tender and directions of Engineer-in-Charge |
| 249 | Flush Mounting Type |
| 250 | Wiring with (No. of wires given below) 660 V grade, 0.63 mm dia. annealed tinned copper conductor, PVC insulated twin flat wire as per relevant IS in already laidsurface/concealed conduit from TDJB onwards to telephone sockets including supplyof Wires, termination and connection, including all labour and materials, as perapproved drawings, specifications of this tender and directions of Engineer-in-Charge |
| 251 | 1 No. twin flat wire |
| 252 | 2 Nos. twin flat wires. |
| 253 | 3 Nos. twin flat wires. |
| 254 | FIRE ALARM SYSTEM |
| 255 | Installation, termination and connection of following fire alarm panel including Power Pack and battery backup system and all associated items, including transportationfrom store/yard to site at the place of installation, assembling and installation onfoundation or fixing to wall or steel structures, aligning, levelling, grouting,termination and connection of cables, making earth connections etc., including alllabour and materials, as per approved drawings, specifications of this tender anddirections of Engineer-in-Charge |
| 256 | Fire alarm panel. |
| 257 | Heat detectors |
| 258 | Zener Barrier |
| 259 | Break glass type fire alarm boxes |
| 260 | Exit signs |
| 261 | Hooters. |
| 262 | Multi sensor type detectors |
| 263 | Fault Isolator modules |
| 264 | Input/Monitoring relay module |
| 265 | Output/Control Relay Module |
| 266 | Hooter Acknowledge Box |
| 267 | Supply of weatherproof type fire alarm junction box (FAJB) suitable for outdoorinstallation with Krone/screw type terminals, including supply of weatherproof doublecompression cable glands and weatherproof plugs to block the unused entry includingall labour and materials, as per specifications of this tender and direction of Engineerin-Charge |
| 268 | FAJB with 1 nos6 Pair incoming cable(s) and 6 nos2 Pair outgoing cable(s) |
| 269 | Installation, testing and commissioning of weatherproof type fire alarm junction box(FAJB) suitable for outdoor installation with Krone/screw type terminals, includingtermination and connections of incoming and outgoing non-jelly cable, excludingsupply of weatherproof double compression cable glands, including all labour andmaterials, as per specifications of this tender and direction of Engineer-in-Charge. |
| 270 | FAJB with 1 nos6 Pair incoming cable(s) and 6 nos2 Pair outgoing cable(s) |
| 271 | LAYING OF COMMUNICATION / FIRE ALARM CABLES |
| 272 | Horizontal and vertical laying/pulling through of communication/fire alarm cables ofthe following overall diameters in ready trays/trenches/conduits or supported onstructures including supplying and fixing of GI saddle and saddle bars, stainless steelstrip number tags, including transportation from store/yard to site at the place ofinstallation, unpacking, including all labour and materials, as per approved drawings,specifications of this tender and directions of Engineer-in-Charge |
| 273 | Cables of overall dia. upto 35 mm. |
| 274 | CIVIL WORKS/M.S. CHEQUERED PLATE |
| 275 | Supply, fabrication and installation of 6 mm thick M.S. chequered plate for covering floor cut- outs/cable trenches etc., including all labour and materials, as per approveddrawings, specifications of this tender and directions of Engineer-in-Charge |
| 276 | 6 mm thick M.S. chequered plate. |
| 277 | Supply and installation of fire proof sealing system as per IEC-60332 including supply and fabrication of steel frames and other accessories (cement, gravel, sand etc.)including drilling, cutting, welding, surface preparation, dressing/ chipping ofconcrete, enlargement etc. including all minor masonry and structural works andrepair of all damages in line with the enclosed job specification and instructions of theEngineer-in-Charge |
| 278 | Making through and through cut outs in pockets of size 150 mm dia in the RCCfloor/walls of trenches/buildings of thickness upto 200mm for facilitation cableentries using concrete cutting machines including all labour and materials as perapproved drawings, specifications of this tender and directions of Engineer -in-charge |
| 279 | LAN SYSTEMS |
| 280 | Supply, installation, connection, testing and commissioning of weatherproof power panels for UPS power distribution having following incomer & outgoing feeders,including all labour and materials, as per approved drawings, specifications of thistender and directions of engineer-in-charge. |
| 281 | 32A, double pole incomer MCB isolator and 6 nos outgoing double pole 10A MCBsisolator with 2nos, 10A semiconducting fuses |
| 282 | 32A, double pole incomer MCB isolator and 12 nos outgoing double pole 10A MCBsisolator with 2 nos, 10A semiconducting fuses , |
| 283 | 63A, double pole incomer MCB isolator and 18 nos outgoing double pole 10A MCBsisolator with 2 nos, 10A semiconducting fuses |
| 284 | PAINTING & MARKING |
| 285 | Letter painting of tag nos., applicable circuit nos. for identification with red/black/white paint for all outdoor equipment in safe and hazardous areas viz. light fittings, control gear boxes, lighting/power panels, welding receptacles,convenience receptacles, local control stations, fire alarm manual call points, firealarm detectors, motors,field call stations, loud speakers, etc. including supply ofenamel paint, all hardware as required,supply of all labour, materials as per thespecification of this tender and directions of Engineer-in-Charge. |
| 286 | Each alphabet/character upto 2 inch in height/length |
| 287 | Each alphabet/character above 2 inch and Upto 4 inch in height/length |
| 288 | Each alphabet/character above 4 inch and Upto 8 inch in height/length |
| 289 | INSTRUMENTATION |
| 290 | Supply Installation, Testing, Training & Commissioning of the following Equipment |
| 291 | Central Computer SystemMulticore 3rd Gen XEON Processor, 16GB RAM, RAID-10 Hard Disk with 4TB capacity(SSD+HDD), 27full HD Monitor, Parallel Port & Serial Port, Wired Keyboard Mouse,Windows server 2022 x 64 or Windows 10 x 64,MS Office with Antivirus software |
| 292 | BMS Server |
| 293 | SoftwareGraphical interface software. The system should be accessible from anywhere on LANor WAN or Ethernet. The Communication protocol shall be one of the IndustryStandard Open Protocols such as BACNet, LONWORKS etc. System should be scalableand should have minimum 2 clients and should fully compliant to the detailedtechnical specifications as per the tender |
| 294 | DDC ControllerStandalone and BACnet IP Networkable 32 Bit or more , 32 MB RAM1GHZ DDCControllers with I/O module as per tentative IO List of Points attached with the tender.The controllers shall be capable of 3 No\"s of RS485 for Modbus/BACnet MSTPIntegration ,standalone operationwith real time clock and historical database. TheDDC\"s shall be capable of peer to peer communication without help of systeminterface controller or PC. The DDCs shall be with suitable IP 67 enclosure completewith all wiring and accessoriesDDC-Plant RoomDDC-ChillerDDC-Air Handling Units & Fans with BasementDDC-HT & LT PanelDDC-DG |
| 295 | Sensors & Field DevicesSupply, installation, testing and commissioning of the following sensors/ transducers/transmitters |
| 296 | Air Flow Switch tomonitor the fan status & Filter Status |
| 297 | T & RH Sensor (for HVAC Duct) with all mounting accessories to measure the return air temperatures in the AHUs |
| 298 | TemperatureSensor (for HVAC Duct) with all mounting accessories to measure thereturn air temperatures in the CSUs |
| 299 | Immersion Temperature Sensor with Well |
| 300 | Water Flowmeter |
| 301 | Water Differential Pressure Switch |
| 302 | Water Flow switch |
| 303 | Current Relay |
| 304 | Ambient Temp. RHsensor |
| 305 | Float Level Switch |
| 306 | Flame proof Level Switch |
| 307 | Diesel Flow Meter flameproof |
| 308 | Level transmitter |
| 309 | Flame proof Level transmitter |
| 310 | pH analyzer |
| 311 | Hardness Analyzer |
| 312 | Ambient Air Quality Sensors |
| 313 | Smoke Sensors |
| 314 | Wiring & ConduitingSupplying, laying, termination, testing and commissioning of signal cables. (2 core 1.5 mm2), Armoured, XLPE insulated, tinned copper conductor FRLS cable- unscreenedfor Command/Status |
| 315 | Supplying, laying, termination, testing and commissioning of signal cables. (2 core 1.5mm2), Armoured, XLPE insulated, tinned copper conductor FRLS cable-screened forSensor/Integration/controller to controller communication |
| 316 | Supplying, laying, termination, testing and commissioning of 4 Core 1.5 SQ. MM,unarmouredArmoured, XLPE insulated, tinned copper conductor FRLS cable -Unscreened for Command/Status/Sensor |
| 317 | Supplying, laying, termination, testing and commissioning of 6 Core 1.5 SQ. MM,unarmouredArmoured, XLPE insulated, tinned copper conductor FRLS cable -Unscreened for Command/ Status/ Sensor |
| 318 | Supplying, laying, termination, testing and commissioning of Cat 6 cable for busconnection- for Integration / controllers |
| 319 | Supply and Laying 3C X 2.5 SQ mmArmored Power cable for DDC\"s , Integrators |
| 320 | Supply and laying MS conduit |
| 321 | 50 x 50 x 2 mm Supply and laying of prefabricated Anodized Aluminum Perforated cable tray |
| 322 | 100mmX50mmX2mm Supply and laying of prefabricated Anodized AluminumPerforated cable tray |
| 323 | Supply and providing of OFC cablewith all required accessories like pig tail, NetworkSwitches, converters, etc. |
| 324 | 55\" LCD Display Screen (Resolution 1920x1080 Full HD or better)to display AirQuality |
| 325 | INFORMATION TECHNOLOGY SERVICES |
| 326 | Certification of Data Communication System |
| 327 | Certification of Data Communication System and submission of performance warranty of 20 years through OEM as per the specifications of this tender and directions ofEngineer-in-Charge |
| 328 | Structured UTP LAN CABLING |
| 329 | Supply, installation, testing (Penta Scanning) and commissioning of Structured UTP LAN Cabling including all labour and materials (Cable, Conduit, Channel), includingfollowing items as per approved drawings, specifications of this tender and directionsof engineer-in-charge: |
| 330 | CAT-6A LSZH-FR |
| 331 | 24-port CAT-6A Jack Panel (fully loaded with 24 Nos. I/Os) |
| 332 | 48-port CAT-6A Jack Panel (fully loaded with 48 Nos. I/Os) |
| 333 | 1-m long CAT-6A Patch Cord |
| 334 | 2-m long CAT-6A Patch Cord |
| 335 | CAT-6A I/O, Faceplates, Gang-box |
| 336 | Equipment Rack - Networking, Server |
| 337 | Supply, installation, testing and commissioning of Network Racks including all labour and materials (including Horizontal and Vertical Cable Managers) of varying sizes, asper approved drawings, specifications of this tender and directions of engineer-incharge |
| 338 | Floor-standing Network Rack |
| 339 | Height 42 uWidth 19 Inch |
| 340 | Wall-mounted Network Rack |
| 341 | Height 15 uWidth 19 Inch |
| 342 | Supply and Laying of PVC conduits pipe |
| 343 | Supply and Laying of PVC conduits as per the specifications of this tender anddirections of the Engineer-in-Charge. |
| 344 | Supply and Laying of PVC conduits of sizes OD 50 mm |
| 345 | Supply and Laying of PVC channels |
| 346 | Supply and Laying of PVC channels as per the specifications of this tender and directions of the Engineer-in-Charge. |
| 347 | Supply and Laying of PVC channels of size OD 25 mmas per the specifications of this tender and directions of the Engineer-in-Charge. |
| 348 | Network Active Components |
| 349 | Supply, installation, mounting, testing and commissioning of Ethernet Edge Switch(s) including all labour and materials, as per approved drawings, specifications of thistender and directions of engineer in charge |
| 350 | POE Ethernet Switch |
| 351 | Total No. of Gigabit UTP Ports 24 No. of POE Ports 24 No. of Fiber Ports 4 |
| 352 | Providing the following personel to BANDR with required experience and qualificationfor the purpose of BANDR\"s work on monthly basis. Note:1. Contractor shall pay the wages, ESI and EPF to the personel mentioned below.2. Contractor shall be capable to pay the wages as per tender document timely before 10th of every month from his own resources.3. The contractor shall be liable for any issues arising in relation to EPF, ESI and shall deal with it taking responsibility of the related procedures.4. The Contractor has to submit the CV/Resume/Bio-data of the peronel to be deployed for BANDR\"s works and shall deploy the personel only after approval of Engineer-in-Charge.5. In case, the person employed by the contractor commits any act of omission/commission that amounts to misconduct/indiscipline/ incompetence, the contractor shall be liable to take appropriate disciplinary action against such persons, including their removal from the site of work.6. The Contractor shall replace immediately any of its personnel found unacceptable to this office because of security risks, incompetence, conflict of interest, improper conduct etc. upon receiving a notice7. This item is for sole purpose of BANDR\"s work and not for contractor\"s work. This item does not relieve the contractor\"s responsibility to bring the manpower required to execute their own work awarded. |
| 353 | Lead Safety OfficerSafety Officer/Engineer should possess following qualification & experience:(i) Recognized degree in any branch of Engg. or Tech. or Architecture with practical experience of working in a building or other construction work in supervisory capacity for a period of not less than two years, or possessing recognized diploma in any branch of Engg. or Tech with practical experience of working in a building or other construction work in supervisory capacity for a period of not less than five years.(ii) Recognized degree or one year diploma in Industrial safety (from any Indian Institutes recognized by AICTE or State Council of Tech. Education of any Indian State/Union territory) with at least one paper in construction safety (as an elective subject).(iii) Preferably have adequate knowledge of the language spoken by majority of the workers at the construction site.Alternately(i) Person possessing Graduation Degree in Science with Physics & Chemistry and degree or one year diploma in Industrial Safety (from any Indian institutes recognized by AICTE or State Council of Tech. Education of any Indian State/ Union Territory) with practical experience of working in a building, plant or other construction works (as Safety Officer, in line with Indian Factories Act, 1948) for a period of not less than five years, may be considered as Safety Officer. |
| 354 | Safety SupervisorAs a minimum, he shall possess class XII pass certificate and trained in fire-fighting as well as in safety/occupational health related subjects, with minimum two year of practical experience in construction work environment and should have adequate knowledge of the local language spoken by majority of the workers at the construction site. |
| 355 | Civil QA/QC OfficerQualification Criteria:Degree or Diploma in Engineering with following experience-Degree holders : 10 yrs of construction experience of which minimum 3 years in QA/QCDiploma holders : 13 yrs of construction experience of which minimum 6 years in QA/QC |
| 356 | Lead Electrical EngineerQualification Criteria:Degree or Diploma in Electrical Engineering with following experience-Degree holders : 10 yrs of construction experience Diploma holders : 13 yrs of construction experience |
| 357 | Electrical EngineerQualification Criteria:Degree in Electrical Engineering with minimum 2 years of relevant experience in construction orDiploma in relevant Engineering Discipline with minimum 4 years of relevant experience in Construction. |
| 358 | \"NOTE:-THE ABOVE RATE SHALL BE INCLUSIVE OF ALL TAXES & DUTIES, ROYALTIES, CESS, FEE, ENVIORMENTAL & POLLUTION, FITNESS & SAFETY CLEARANCE CHARGES (IF ANY), OR ANY OTHER INCIDENTAL CHARGES ETC BUT EXCLUDING GST.\" |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
