|
| 1 | Notes:-(i) The scope includes worksto be carried out from ground level to nearly upto 45 metres of height.(ii) Quoted rates are deemed to be inclusive of scaffolding /boom lift/ crane as required. Contractor shall arrange necessary scaffolding/ boomlift/crane and takes all safety precautions for workers at the time of carrying out works asdescribed in Sch \"A\"/ BOQ.(iii) Contractor shall visit the site before quoting the tender to assess the resources required to execute the work as the site include prestigeous buildings of INA.(iv) Quoted rates shall include preparation of surface and application of paint as per manufacturer\"s instruction using mechanical means all as specified and directed by Engr-in-Charge.(v) The work may be carried out at different locations and in different measurements/ touch ups even it is below 1 Sqm or othewise. (vi) Quoted rates shall include cleaning of paint stains on floor/ window/ joinerysurfaces etc..(vii) Cost of all factors are deemed to be included in the rate quoted in BOQ. No extra claim shall be entertained on this account.(viii) All debris and unserviceable items shall be removed from site and thrown away at dumping area outside INA area upto a distance of 10.00 Kms as directed. Loading, Unloading , stacking and transportation charges are included in relevent items of taking down or demolition / dismantling. All debris should be taken outside of INA Campus and if any debris found dumped inside INA campus, a fine of Rs 5000.00 per load or per cum will be recovered from contractor. |
| 2 | Taking downshutters of any description not exc 1 sqm each complete all as specified and as directed by Engineer in Charge. |
| 3 | Taking downshutters of any description exc 1 sqm and n.exc 2 sqm each complete all as specified and as directed by Engineer in Charge. |
| 4 | Taking down chowkhats or frames exc 1.5 sqm but not exc 4 sqm each (without taking off shutters from the frame) complete all as specified and as directed by Engineer in Charge. |
| 5 | Supply and fix 150 mm anodized aluminium barrel tower bolt of extruded section complete all as specified and as directed by Engineer in Charge. |
| 6 | Supply and fix100mm butt hinges cast brass, with mild steel hinge pin, bright polished and fixed type B-11 complete all as specified and as directed by Engineer in Charge. |
| 7 | Supply and fix in repairs 150 mm anodized aluminium barrel tower bolt of extruded section all as specified complete all as specified and as directed by Engineer in Charge. |
| 8 | Supply and fix in repairs 100 mm mild steel butt hinges, cold rolled medium weight complete all as specified and as directed by Engineer in Charge. |
| 9 | Supply and fix in repairs 150mm extruded anodised aluminium alloy handles fabricated type complete all as specified and as directed by Engineer in Charge. |
| 10 | Supply and fix in repairs mortice lock brass body, 100 mm, 4 levers vertical type complete all as specified and as directed by Engineer in Charge. |
| 11 | Supply and fix in repairs 75 mm hasp and staple mild steel safety type, stove enamelled black, including bolt to hinge plateand fixed with screws complete all as specified and as directed by Engineer in Charge. |
| 12 | Supply and fix in repair floor door stopper 150mm size aluminium alloy body and tongue double legged, anodised with hard drawn steel spring fixed to door complete all as specified and as directed by Engineer in Charge. |
| 13 | Supply and fix in repairs aluminum (die cast) body door closer hydraulically regulated designation No.3 universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and as directed by Engineer in Charge. |
| 14 | Supply and fix in repair aluminum alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminum wire staples complete all as specified and as directed by Engineer in Charge. |
| 15 | Supply and fix in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed by Engineer in Charge. |
| 16 | Supply and fix in repairs 75mm long anodised aluminium handle cum lock for sliding window/ ventilator shutter complete all as specified and as directed by Engineer in Charge. |
| 17 | Supply and fix in repairs mild steel friction hinges suitable for window/ ventilator shutters complete all as specified and as directed by Engineer in Charge. |
| 18 | Taking down aluminium shutters exc 1.00 sqm and not exc 2sqm each(without taking out frame) and refixing in the same positon after carrying out repairs and provision of aluminum tie rod at top and bottom rails complete all as specified and as directed by Engineer in Charge. |
| 19 | Material and labour for aluminium powder coatedwindows and ventilator shutters etc. side hung type without sash bars,aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos) suitable handle (1 No) etc.(minimum thickness of powder coating not less than 50 micron) complete all as specified and as directed by Engineer in Charge. |
| 20 | Supply and fix aluminium powder coated door shutter, side hung type aluminium section weighing not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc.(minimum thickness of powder coating not less than 50 micron) complete all as specified and as directed by Engineer in Charge. |
| 21 | Supply and fix aluminium powder coatedframe for partitions, doors, windows, ventilators with one or more rebates including joining cleats for fixing etc. (minimum thickness of powder coating not less than 50 micron) complete all as specified and as directed by Engineer in Charge. |
| 22 | Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/ slabs/ any thickness including cover fillets complete all as specified and as directed by Engineer in Charge. |
| 23 | Material and labour for providing polyester foil coated aluminium alloy (metal profile of width 300mm or suitable size for ends with thickness of channel/profile sheet min 01 mm ) for false ceiling including suitable Carrier span and hangers in existing grid work as per manufacturers instructions and complete all as specified and as directed by Engineer in Charge. |
| 24 | Ditto as per item ser No 23 above but fixing onlyall as specified and as directed by Engineer in Charge. |
| 25 | Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm X 605mm size, consisting of main Tee of SIze 123.50mm x 36.50mm x 1.50mm, cross Tee of size 23.50mm×23.50mm x1.50mm and wall angle of size 1.50 x1.50mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm end level fixed to roof slabs by means of ceiling cleats made out of G.I. of size 60 mm long and expansion hold fasteners 40 mm long in soffit slab/walls with and including 4mm thick non-abestos fibre cement building boards panels 600 mm x 600 mm size including taking down of old false ceiling complete all as specified and as directed by Engineer in Charge. |
| 26 | Supply and fix in repair 18/19mm thick pre-laminated particle board exterior grade, one side decorative choice lamination and other side balancing white lamination, fixed with screws to wooden / aluminium frame work as in cupboard shutters complete all as specified and as directed by Engineer in Charge. |
| 27 | Supply and fix in repair 9mm thick pre-laminated particle board exterior grade, one side decorative choice lamination and other side balancing white lamination, fixed with screws to wooden / aluminium frame work as in cup board shutters complete all as specified and as directed by Engineer in Charge. |
| 28 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed by Engineer in Charge. |
| 29 | Material and labour for for 4mm thick sheet glass plain ordinary quality not exc 0.50 sqm in each pane and glazing with beading complete all as specified and as directed by Engineer in Charge. |
| 30 | Material and labour for for 5.5 mm thick sheet glass plain ordinary quality not exc 0.50 sqm in each pane and glazing with beading complete all as specified and as directed by Engineer in Charge. |
| 31 | Supply and fix in repair vitreous China wash basin,white/coloured (flat back) 550x400mm excluding pillar tap, but including fixing brackets, cutting for and pinning in ends of brackets complete all as specified and as directed by Engineer in Charge. |
| 32 | Supply and fix in repairs pillar taps 15 mm size (with push button fancy type) cast copper alloy, chromium plated screwed down high pressure screwed for iron pipe & fixed complete all as specified and as directed by Engineer in Charge. |
| 33 | Supply and fix in repair vitreous china, wash down water closet(EWC) with seat cover white/coloured, closed pattern with flat bottom and cover with mild steel (CP) or aluminium hinging device fixed with necessary bolts complete all as specified and as directed by Engineer in Charge. |
| 34 | Supply and fix in repairs vitreous china wash down water closet pan cascade type including flushing cistern, light coloured, with seat cover closed pattern with flat bottom, cover with suitable hinging device etc including connection to drain (or outgoing pipe)complete all as specified and as directed by Engineer in Charge.Make : Jaquar Cat. No: CNS-WHT-853S300SPPSM, Hindware Cat. No : Cat. No.: 92573 (S-22) or CEAR Cat No. Cat. No. S1013229. |
| 35 | Supply and fixing in repairs Vitreous China half stall urinal, light coloured, of size 580mm x 380mm × 350mm complete with chromium plated waste fittings including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2. securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement, (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)complete all as specified and as directed by Engineer in Charge. |
| 36 | Supply and fix in repair vitreous ChinaVitreous china urinal partition white of size 310x700 mm complete all as specified and as directed by Engineer in Charge. |
| 37 | Supply and fix plastic seat cover (colour) closed pattern with flat bottom suitable for EWC including taking down old cover complete all as specified and as directed by Engineer in Charge. |
| 38 | Supply and fix in repair10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve, float and handle including brackets complete all as specified and as directed by Engineer in Charge. |
| 39 | Supply and fix in repairs 15mm bore chromium plated bib taps (with push button fancy type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes complete all as specified and as directed by Engineer in Charge. |
| 40 | Supply and fix in repair angular stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, chromium plated, fancy type, screwed both ends for iron pipe or for union and fixed, suitable for 15 mm bore pipe,complete all as specified and as directed by Engineer in Charge. |
| 41 | Supply and fix in repair chromium plated towel ring complete all as specified and as directed by Engineer in Charge. |
| 42 | Supply and fix in repair 20mm dia, D type, 60cm long cast copper alloy, chromium plated towel rail, complete all as specified and as directed by Engineer in Charge. |
| 43 | Supply and fix in repair cast copper alloy, chromium plated toilet paper holder, complete all as specified and as directed by Engineer in Charge. |
| 44 | Supply and fixin repair chromium platedsoap tray fixed with stainless steel screws complete all as specified and as directed by Engineer in Charge. |
| 45 | Supply and fix in repair chromium plated Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engineer in Charge. |
| 46 | Supply and fix in repair Cast copper alloy, chromium plated waste coupling with long shank, half thread, 32 mm dia, for WHB etc. complete all as specified and as directed by Engineer in Charge. |
| 47 | Taking up or down steel tubing and connections, 15mm dia complete all as specified and as directed by Engineer in Charge. |
| 48 | Taking up or down steel tubing and connections, 20mm dia complete all as specified and as directed by Engineer in Charge. |
| 49 | Supply and fix 15/16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed by Engineer in Charge. |
| 50 | Supply and fix 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed by Engineer in Charge. |
| 51 | Supply and fix in repairs 5.5 mm thick bevelled edge mirror 600x450mm, selected quality glass mounted on 6mm thick PVC/AC building board/commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and as directed by Engineer in Charge. |
| 52 | Supply and fix in repairs 32mm dia PVC flexible waste pipe for urinals/WHB/sink complete all as specified and as directed by Engineer in Charge. |
| 53 | Supply and fix in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by Engineer in Charge. |
| 54 | Supply and fix in repair PVC (SWR) pipes of 75mm dia single socketed in any length with rubber ring joints fixed to walls ccomplete all as specified and as directed by Engineer in Charge. |
| 55 | Supply and fix in repair PVC (SWR) pipes of 110mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer in Charge. |
| 56 | Supply and fix in repair 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer in Charge. |
| 57 | Demolition of brick work, PCC block or stone masonry built in cement mortar complete all as specified and as directed by Engineer in Charge. |
| 58 | Material and labour forprecast cement concrete block masonrywith solid blocks type C1, 1:3:6 (using 20mm graded stone aggregate) exc 10 cm in width and set in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge. |
| 59 | All as per item No 56 aboveexcept PCC blocks complete all as specified and as directed by Engineer in Charge. |
| 60 | Dismantling floor hearth or wall tiling including cement mortar bedding and rubbish of the premises complete all as specified and as directed by Engineer in Charge. |
| 61 | Material and labour for coloured Non-skid ceramic tiles (square/rectangular) 7 to 8 mm thick in floors, area of each tile exc.0.06 sqm but n.exc 0.11 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge. |
| 62 | Material and labour for coloured Non-skid ceramic tiles (square/rectangular) 7 to 8mm thick in floors, area of each tile exc.0.11 sqm but n.exc 0.18 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge. |
| 63 | Material and labour for Glazed ceramic coloured tiles 350x250x7mm / 450x350x7mm thick in vertical surfaces of stone/brick wall, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick backing coat plaster in cement mortar 1:4 complete all as specified and as directed by Engineer in Charge. |
| 64 | Material and labour forvitrifiedcolourd ceramic tiles 10mm thick (square/rectangular), light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc.set with or without spacers and jointed in neat cement slurry and pointed in white or coloured cement /epoxy to match the shade including 20mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by Engineer in Charge. |
| 65 | Material and labour for vitrified ceramic tiles 10mm thick (square/rectangular), light shade polished, area of each tiles not exceeding 0.36 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match of light shade including 15mm thick backing coat plaster in cement mortar 1:4 complete all as specified and as directed by Engineer in Charge. |
| 66 | Dismantling stone slab and tiles of any description or thickness in floors, landings aprons etc.. laid bedded and pointed in any mortar including bedding concrete complete all as specified and as directed by Engineer in Charge. |
| 67 | Material and labour for cement concrete type B0, 1:2:4 using 12.5 mm graded stone aggregate in sub floors, pavings complete all as specified and as directed by Engineer in Charge. |
| 68 | Material and labour for chequered cement concrete tiles 250x250x25mm / 300x300x25mm thick in floors, with mixture of grey cement and pigments, set, jointed and pointed in neat cement slurry over and including20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge. |
| 69 | Material and labour formachine cut granite stone slab 20mm thick of approved colour and shade as in floors laid over 20mm thick screed bed in cement mortar 1:6; and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab including grinding and polishing complete all as specified and as directed by Engineer in Charge. |
| 70 | Material and labour for 25mm thick flame finished sadarhally machine cut stoneof approved colour and shade as in floors, skirting/dado etc over and including 15mm thick backing coat in cement mortar 1:4; laid and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab complete all as specified and as directed by Engineer in Charge. |
| 71 | Material and labour for machine cut kota stone slab flooring with 20-25mm thick over and including20mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry and pointed with white cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer in Charge. |
| 72 | Material and labour for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting-dado and pillar laid , jointed with grey cement slurry and pointed with white cement mixed with pigment to match the shade of the slab over and including 15 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer in Charge. |
| 73 | Rounding to edges of stone slabs to one edge, such as in steps and other similar situations complete all as specified and as directed by Engineer in Charge. |
| 74 | Stone grit for cushion bed below interlocking paver blocks complete all as specified and as directed by Engineer in Charge. |
| 75 | Material and labour for machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness. M-35 grade with grey cement and pigmentcomplete all as specified and as directed by Engineer in Charge. |
| 76 | All as per item No.75 abovebut except tiles complete all as specified and as directed by Engineer in Charge. |
| 77 | Taking down cement or cement lime plaster on brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by Engineer in Charge. |
| 78 | Material and labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and as directed by Engineer in Charge. |
| 79 | Material and labour for10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and as directed by Engineer in Charge. |
| 80 | Material and labour for preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat of chalk whiting complete all as specified and as directed by Engineer in Charge. |
| 81 | Material and labour for preparation of newlyplastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed by Engineer in Charge. |
| 82 | Cleaning of choked particle from filter system of automatic sensor urinal unit removing top cover of urinal and cleaning automatic sensor unit for removing dust particle etc and making the unit in serviceable condition complete all as specified and as directed by Engineer in Charge. |
| 83 | Supply and fix ceiling tiles for mangalore pattern tile roofing, laid dry etc complete including dismantling of existing broken ceiling tiles complete all as specified and as directed by Engineer in Charge. |
| 84 | Supply and fix in repair rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fied in position all as speciifed in SSR Part I of capacity 500 L with ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed with25mm dia of pipe complete all as specified and as directed by Engineer in Charge. |
| 85 | All as per item No.84 abovebut 1000 L capacity complete all as specified and as directed by Engineer in Charge. |
| 86 | Supply and fix in repairs 20 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer in Charge. |
| 87 | Supply and fix in repairs 25 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by Engineer in Charge. |
| 88 | Supply and fix in repairs 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer in Charge. |
| 89 | Supply and fixurinal spreader of brass chrmium plated and flush cock (lever type) 25mm complete all as specified and as directed by Engineer in Charge. Make: Cat Part No. KBEA -32 of Prayag or equivalent. |
| 90 | Supply and fix in replacement flush kit of low level flushing cistern of cascade type WC complete all as specified and as directed by Engineer in Charge. |
| 91 | Supply and fix in replacement Aluminium Composite Panel 4mm thick of any colour and shade of Alu Bond or equivalent fixed with self tapping screws on existing aluminium frame work complete all as specified and as directed by Engineer in Charge. |
| 92 | Material and labour for12mm thick plywood, grade BWP, tuype BB fixed with screws to aluminium frame work with 3mm thick decorative face veneer of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instructions including takin down of old plywood all as specified and as directed by Engineer in Charge. |
| 93 | Material and labour for pre laminated wooden flooring 8mm thick and panel size 120cm x 19 cm / 180 cm x 19 cm of PERGO or equivalent all as per manufacture\"s instructions including taking down of old wooden flooring all as specified and as directed by Engineer in Charge. |
| 94 | Material and labour for pre laminated wooden flooring skirting 70 mm width matching with laminated wooden flooring of PERGO or equivalent all as per manufactures instructions including takin down of old skirting all as specified and as directed by Engineer in Charge. |
| 95 | Repair/ replacement tosafety lever locks mild steel with levers for rolling shutters of area not exceeding 15 Sqm complete all as specified and as directed by Engineer in Charge. |
| 96 | Repair/ replacement to MS spring for rolling shutters and applying greas on steel surfaces in side channels for smooth functioning of all steel members for rolling shutters of area not exceeding 15 Sqm complete all as specified and as directed by Engineer in Charge. |
| 97 | Repair/ replacement to interlocking lath section and ball bearing on either side of rolling shutters of area not exceeding 15 Sqm complete all as specified and as directed by Engineer in Charge. |
| 98 | Repair/ replacement to MS tie rodfor rolling shutters of area not exceeding 15 Sqm complete all as specified and as directed by Engineer in Charge. |
| 99 | Repair/ replacement to MS push plate for rolling shutters of area not exceeding 15 Sqm complete all as specified and as directed by Engineer in Charge. |
| 100 | Material and labour for plastering in patches, area not exc. 1.5 sqm with cement mortar 1:4 as in wall/ceiling and matching with surrounding surfaces including taking down damaged portion complete all as specified and as directed by Engineer in Charge. |
| 101 | Material and labour for plastering in patches, area not exc. 1.5 sqm with cement mortar 1:6 as in wall/ceiling and matching with surrounding surfaces including taking down damaged portion complete all as specified and as directed by Engineer in Charge. |
| 102 | Material and labour for cement concrete type B1 , 1:2:4 (using 20mm graded stone aggregate)in patches, area n.exc 02 Sqm to repair damages in floor, plinth protection, roof gola, path and similar work etc complete all as specified and as directed by Engineer in Charge. |
| 103 | Supply and fix in repair Single lever surgical purpose elbow action sink mixer (wall mounted) complete all as specified and as directed by Engineer in Charge. of Jaquar make (Code : FLR-CHR-5166) or equivalent. |
| 104 | Supply and fix in repair Florentine pillar cock of Jaquar make (Code : FLR-CHR-5031N) or equivalent (elbow operated) suitable for hospital complete all as specified and as directed by Engineer in Charge. |
| 105 | Supply and fix in repair Florentine Bib cock of Jaquar make (Code : FLR-CHR-5043N) or equivalent (elbow operated) suitable for hospital complete all as specified and as directed by Engineer in Charge. |
| 106 | Supply and fix in repairs PVC Lid/cover for 500 L/750 L capacity water tank complete all as specified and as directed by Engineer in Charge. |
| 107 | Supply and fix in repairs PVC Lid/cover for 1000 L/ 2000 L capacity water tank complete all as specified and as directed by Engineer in Charge. |
| 108 | Supply and fix in repairs PVC Lid/cover for 5000 L capacity water tank complete all as specified and as directed by Engineer in Charge. |
| 109 | Supply, fabricate, erect and fix in position Galvanised Iron steel work in tubular sections of any size including special shaped washers, as in posts, purlins, staircase, railing etc complete using ERW or linduction butt welded tubes conforming to IS-1239 (Part I) 1990 complete all as specified and as directed by Engineer in Charge. |
| 110 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engineer in Charge. |
| 111 | Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of capacity of tanks exc 250 & n.exc 500 litres complete all as specified and as directed by Engineer in Charge. |
| 112 | Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of capacity of tanks exc 500 & n.exc 1000 litres complete all as specified and as directed by Engineer in Charge. |
| 113 | Supply and fix 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking up or down old steel tubing and connections, 25 mm dia complete all as specified and as directed by Engineer in Charge. |
| 114 | Supply and fix in repairs vitreous china urinal flat back fixed to wall including suitable chromium plated coupling complete all as specified and as directed by Engineer in Charge. Make : Jaquar Cat. No: URS-WHT-13261/ Hindware Cat. No: 60002/CERA Cat. No: S4020112 |
| 115 | Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by Engineer in Charge. |
| 116 | Material and labour for preparation of old decorated surfaces and applying one coat of acrylic emulsion (interior grade) on plastered surface including filling of depressions/ holes with internal wall care putty and necessary scaffoldingsall as specified and as per manufacturers instructions and as directed by Engineer in Charge. |
| 117 | Material and labour for complete removal of existing surface by scrapping of walls including cornices/pillars etc. by brooming down and applying two coats of acrylic emulsion paint interior grade (Apcolite of Asian paints or equivalent make in Berger/Shalimar) over a coat of emulsion primer over a coat ofwall putty of uniform finish complete all as specified and as directed by Engineer in Charge. |
| 118 | Material and labour for preparation of old treated surfaces and applying one coat of acrylic emulsion (exterior grade)paint on wall includingfilling of depressions/ holes with external wall care putty and necessary scaffoldingsall as specified and as per manufacturers instructions andall as specified and as directed by Engineer in Charge. |
| 119 | Material and labour for preperation of old decorated surfaces and applying one coat of sandtex matt finish on plastered surfaceas permanufacturer\"s instructions and all as specified and as directed by Engineer in Charge. |
| 120 | Material and labour for preparation of old decorated surfaces and applying one coat of acrylic emulsion (interior grade) on ceiling including filling of depressions/ holes with external wall care putty and necessary scaffoldingsas permanufacturer\"s instructions and all as specified and as directed by Engineer in Charge. |
| 121 | Material and labour for preparation of old decorated surfaces and applying one coat of white wash on ceiling including necessary scaffoldings complete all as specified and as directed by Engineer in Charge. |
| 122 | Material and labour for preparation of old painted steel/ iron surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer in Charge. |
| 123 | Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of epoxy paint complete all as specified and as directed by Engineer in Charge. |
| 124 | Material and labour for french polishing on surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wood filler on old works with one or more coats complete all as specified and as directed by Engineer in Charge. |
| 125 | Preparation of old treated MP roof tile surfaces by cleaning with by wire brushes to remove all existing fungal growth etc and applying one coat of antifungal paint using UNIGLOSS deluxe multi surface paint or equivalentcomplete all as specified and as directed by Engineer in Charge. |
| 126 | Material and labour for removing shrubs, vegitation, roots etc.. from external wall surfaces , by dismantling brick work , RCC or taking down plastering as the case may be, including dismantling SWR pipes, OH PVC service tanks etc. and refixing the same in original position and making good the surface dismantled complete all as specified and as directed by Engineer in Charge. (Area to be dismantled exc 1 Sqmand not exc 3 Sqm) |
| 127 | Material and labour for treating holes cracks etc. up to 10 mm making V groove using patti blades and filling the cracks with ready to use crack fillers and allowed to drycomplete all as specified and as directed by Engineer in Charge. |
