Lighting work in Saumitra Forest Park - Supply and Installation of Decorative steel pole is made out of mild steel galvanized two profile bottom profile 1000mm x125mmx4.00 mm and upper ribbed profile 2500mmx81mmx3.5mm with cast iron embelishment E8 . the pole has a service window atbottom section with heavy duty four way connector and a MCB mild steel base plate 300x210 mm with four nos mounting holes is fixed with welded with bottom section pole is primer coated and polyurethane painted.Decorative pole shall be installed at desired location including foundation of the pole by making cement concrete foundation of 1:2:3( 1 cement: 3 course sand : 6 graded stone aggregate 40mm nominal size) with the help of anchor bolts and 38mm G.I sleeve as required. make: phillips, bajaj, as per direction of E/ic (PSR Begam Hazrat Mahal Park) 3 S/F of ornamental type luminaire 40-45 watt LED post top fitting make of aluminium 534 mm long housing duly powder coated/PU painted with PC/PMMA clear/frosted diffuser with sturdy triple arm MCPCB having high umen LEDs are mounted on aluminium heat sinks. make: phillips, bajaj as per direction of E/ic(PSR Begam Hazrat Mahal Park) 4 Supply and fixing of DWC HDPE Pipe along with all accessories like socket, band, coupling etc. confirming to IS 14903 PartII complete with fixing and cutting jointing etc. (63mm OD and ID51 mm nominal) DSR/2022(E/M) No 14.161) 5 S/B Supply of feeder pillar Box, with alumnium bsuhar-4 strip enclosure CRC & street powder coated outdoor type alumnium busbar 20x44 strip, MCB DP 32m AMP-4 Nos. 3pin socket 32Amp-1 no. enclosure size 300x350x200mm (PSR) 6 S/B of Earth rod 20 mm dia 2.5 mt long including GI wire 7/16 SWG to connected earth rod and earth clamp on pole, 3 mtr long steel conduit to carry earth wire along the pole complite as per approved of E/Ic (PSR) 7 Supply & fixing of 30mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 4 mm. Top dia minium 150 mm, Bottom dia 500 mmbase plate 32 mm thick suitable for wind velocity as per IS 875 part 3 &having no circumferential weld, with accessories for high mast such as head frame suitable for 8 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 8 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. SOR-655/18 8 Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 Watt. Confirming to IP 66 protection complete in all respect. As per PWD shcedule 2018 SI No.1455 CAT AAA 9 Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter,voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestaltype for Cat-B and C only. As per PWD schedule 2018 SI No.802 10 Incoming 400 AMP TPN-01 Nos. Outgoing- 200 AMP TPN-2 Nos & 63 amp TPN-01 Nos. 11 Incoming 200 AMP TPN-01 Nos. Outgoing- 100 AMP TPN-1 Nos and 63 amp TPN-03 Nos. 12 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. As per PWD schedule 2018 SI No. 501 13 10 sqmm 4 core 14 16 sqmm 4 core 15 95 sqmm 3-1/2 core 16 Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRCfuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect As per PWD schedule 2018 SI No. 807 17 40 A TPN 18 Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing (This will apply for earthing of poles also). As per PWD schedule 2018 SI No. 702 19 Supply and wiring of submain with two number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia. heavy guage rigid steel conduit on surface, with one number 14 SWG copper earth continuity wire etc, complete in all respect. As per PWD schedule 2018 SI No. 1301(B) 20 PART-B 21 H.T/L.T Work 22 S/F of double pole structure with 2 nos ST. pole for S/S 410 SP-55 11 Mtr. long in 1:3:6 CC foundation 1/6 of pole length below G.l. and 30cm above G.1. 20cm thick around the pole with 2 nos. channel 125mmx75 mm one No. Chennel cross arm of 75mmX 40mm 2 No. 50X50X6mm sngle iron bracings with necessary nut bolts & packing pieces complete with painting as per direction of B/L PSR Bond No.87/CE/EE(E/M)/2021, Dated 09-11-2021 23 S/F of 11 KV Pin insulator with G.1. Bolt/spindle nut etc. complete in all respects. PSR Bond No.87/CE/EE(E/M)/ 2021, Dated 09-11-2021 24 S/E of 11 K.V L.A. set of 3 wire. suitable for mounting on steel support complete in all respect as per direction of E/I. PSR Bond No.87/CE/EE(E/M)/2021, Dated 09-11-2021 25 S/E of 11 K.V. T.P.M.O. switch on pole including handle rod etc. complete in all respects as per direction of E/Ich. PSR Bond No.87/CE/EE(E/M)/2021, Dated 09-11-2021 26 S/E of 11 K.V. D.O. fuse set on pole complete in all respect as per direction of E/1. PSR Bond No.87/CE/EE(E/M)/ 2021, Dated 09 11-2021 27 Supply and laying of 70 Sqmm 3 core 11 KV standered aluminium conductor XLPE (Cross linked polyethylene) insulated PVC bedded Galvanised flat steel strip armoured cables confirming to 1.S. 709 (Part-II with latest amendments) II KV grade at a depth of 900 m below ground level over a cushion of 100 mm thick fine river sand a around and protected with well burnt bricks on sides and on top pu across. The armouring of cable shall be properly connected wi earth conductor by clamps etc. PWD SOR No: 506 (d) 28 S/F of 70 Sq.mm size 3 core XLPE 11 KV outdoor type jointing kit proper completion of work as per direction of E/I A.R. Make: Raycheme, Mahindra. PSR Bond No.02/CE/EE(E/M)/2022, Dated 19.04.2022) 29 S/F of level 2 following capacity 11/0.433 K.V. Al wound! conventional 50Hz 3 phase oil immersed naturally cooled distribution T/F confirming and with amendments there of, having losses as per BEE standered with all standard fittings, including first filling of oil complete in all respects, of make UPPCL/KESCO Approved 30 (a) 100 KVA 31 Supply and burring of Safe Earthing Electrode T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6. terminal Dia 12 mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 x 3 G.1. Strip will be extra)Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. S.I.No-726 B/18. 32 S/L of 25mmx3mm Gl strip from earth electrode directly in the ground as required complete in all respect Item No 716-SOR-2018 33 Supply and fixing of 2 metres high cage fabricated with 3mm thick expanded metal fixed on 50mm x 50mm x 6mm angle iron frame having vertical members spaced at 1 to 1.25 mts and horizontal members spaced at 1 mt. The vertical members shall be grouted in floor and horizontal members in the wall to a depth of 300mm with ends forked.The cage shall have 2000mm x 1000mm size one leaf door with locking device having door frame fabricated with 35mm x 35mm x 6mm angle iron and 3mm expanded metal duly fixed with the cage member with hinges etc. The cage shall be painted with red oxide primer and synthetic enamel paint. The job includes all materials, labour, T&P etc. for proper completion of work. PWD SI No: 1142 34 S/E of 2.24 mtr. Long cross arm 50mmx 50mm. channel on pole including clamps, eye bolts etc. with red enamel paint as per direction of E/Ich. (Analysed as per SOR- 2020 civil) 35 S/L of following size G.l. B class pipe at a depth of 750mm below ground level as cable carrier as direction of E/Inch. (PSR Bond No.02/CE/EE(E/M)/2022, Dated 14.09.2022) 36 (a) 80 mm dia 37 S/F of 11000 V danger board and Fabricated from 10 gauge MS sheet on pole as per electricity rule as per direction of E/Ic SI.No. 1109/18
