Tender For Various Development Works At Shivaji Park, bhilwara-Rajasthan

Tender For Various Development Works At Shivaji Park; 1 Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 Mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter.All kinds of soil. 2 Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =All up to plinth level 1:5:10 (1Cement :5 Course Sand :10 Graded stone aggregate 40 mm nominal size 3 Brick work with clay flyash F.P.S. brick(IS 13757- 1993 ) of class designation 75 in superstructureaboveplinth level upto floor five level in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 4 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20 mm thick. 5 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 6 S/ F of pre cast cement kerb stone / road liner as per drawing enclosed us M-15 concrete smooth finished block fixed at site with C.M. 1:3 Thickness of joint shall not be more than 5mm and 20mm thick bed of C.M. 1:6 complete in all respect with all lead and lift as per direction of Engineer incharge SIZE 400 * 450 * 150 MM 7 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 8 Construction of un-reinforced without dowel bar plain cement concrete pavement over a prepared sub-base with 43 grade cement, coarse and fine aggregate conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrance, sealant primer, joint sealant, debonding strip, admixtures as approved, curing compound, finishing to lines and grades as per drawing complete as per MoRTH specification clause 602. Using Cement Concrete M-20 Pavement Grade 9 Painting with enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work. 10 Supplying and Filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. 11 Polished Blue Kota Stone flooring skirting, laid over 20 mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : For area of each slab from 2001 to 5000 Sq.Cm 12 Providing and fixing 1st quality MAT & GLOSSY finished ceramic tile confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).Size 300mm x 600mm 13 Dismantling of old decayed /damagedexisting ornamental gate of arch shaped both pillars of height approx. 10 ft in round shape and reconstruction of gate with nominal reinforcement and CC M-20 with all shuttering work including murgha jali for support, 12 mm plaster in c.m 1:2, with base and primer and touchwood colour with design and shade as wooden pattern work with design and disposal of material complete job work as per direction and satisfaction of engineer incharge. 14 Making of Railing on existing boundry wall as per following specification design 2 nos. Vertical pole should be made in 1.0 MTR distance & 1.0 MTR height and also 3 thickness. 2 nos crosspole should be made per above specification 1 nos horizontal pole should be use made on top side as per above specification. 3 nos. 8mm size bars should be use every pole with 6 nos. rings of 4 m. G.I.wire. the stainless steel murga jalishould be fixed with every pole C.C. work all poles should be complete by 1:1:2 RCC mixture with the 12mm plaster work should be complete by 1:2 mortar of not less than 12 mm thick.finishing work should be complete by chemical colours as per direction & made the pillar in Bally or bamboo design or as per direction after finishing work should be done two or more coats of touch wood. Work should be done as per direction of in charge

INR 500 /-

INR 30000.0 /-

INR 15 Lakhs /-