Work Of Gym Equipment In Ward No. 110 Of Jagatpura Zone , Crosstrainer Providingandfixingofcrosstrainerofsizenotlessthan1140mm(Length)X625mm(Width)X1750mm.(Height),To Enhancethe Mobilityof Upperand Lowerlimbs And Improve The Flexibilityof Joints.The Main Structure Frame Shallbe Madefromg.I.Pipeminimumof80nb“C” Classweldedwithm.S.Roundbaseplateat Leastø250mm&10Mmthick.Thehandleframeshallbemadeupofat Least25nb“C”Classg.I.Pipe.Thefootrestsshallbemadefromlldpe/Aluminumcastingmaterialofsizenotlessthan130mmx310mmx5mmthicknessandmounted On M.S. Plate Of Size 130Mmx310mmx3mm Thick.High Tensile Steel Withgalvanizednutsandboltsshall Beused For Assembly. Thepowder Coatingshall Bedonewith Purepolyesterpowdersofackzonoble/Berger/Nerolacpaintswith 60To 70 Micron Thicknesses Complete In All Respect Including Fixing The M.S. Holdfast Incementconcretetoholdthewholestructure,Underthedirectionsofengineer-In-Chargetofulfillthefunctionalrequirement. , Seatedpuller Providingand Fixing Of Seated Pullerof Sizenot Lessthan 2400Mm(Length) X800mm(Width)X2000mm.(Height),Toenhancethestrengthofupperlimbsandthemusclesinchestandbackandpromotecardio-Pulmonaryfunction.Themainstructure Frame Shall Be Made From G.I. Pipe Minimum Of 100Nb “C” Class Weldedwith M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick. The Handle Frame Shallbe Minimum Of 32Nb “C” Class G.I. Pipe. The Seat Frame Minimum Of 50Nb “C”Classg.I.Pipe,Closingcapsshallbemadeupoflldpe/Highquality Fiberreinforced Plastic Material. High Tensile Steel With Galvanized Nuts & Bolts Shall Beused For Assembly. The Powder Coating Shall Be Done With Pure Polyester Powdersof Ackzonoble/ Berger/ Nerolac Paints With 60 To 70 Micron Thickness Complete Inall Respect Including Fixing The M.S. Holdfast In Cement Concrete To Hold The Wholestructure,Underthedirectionsofengineer-In-Chargetofulfillthefunctionalrequirement. , Chestpress Providing And Fixing Of Chest Press Of Size Not Less Than 2200Mm (Length) X 800Mm(Width)X2000mm.(Height),Toenhancethestrengthofupperlimbsandthemusclesinchest&Backandpromotecardiopulmonaryfunction.Themainstructure Frame Shall Be Made From G.I. Pipe Minimum Of 100Nb “C” Class Weldedwith M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick. The Handle Frame Shallbe Made Up From At Least 32Nb “C” Class G.I. Pipe. The Seats And Back Rests To Befitted On The Outer Frames Shall Bemade Up Of M.S. Sheet Of Size Not Less Than330mm X 300 Mmx2mm Thickness. Closing Caps Shall Be Made Up Of Lldpe/Highquality Fiber Reinforced Plastic Material. High Tensile Steel With Galvanized Nuts &Boltsshallbeusedforassembly.The Powdercoating Shallbe Donewith Purepolyester Powders From Ackzonoble/ Berger/ Nerolac Paints With 60 To 70 Micronthicknesscompleteinallrespectincludingfixingthem.S.Holdfastincementconcrete To Hold The Whole Structure, Under The Directions Of Engineer-In-Charge Tofulfillthefunctionalrequirement. , Pommelhorse Providing And Fixing Of Pommel Horse Of Size Not Less Than 2150Mm (Length) X800mm (Width) X 800Mm. (Height), To Enhance The Flexibility Of Lower Limbs, Waistand Abdomen. The Main Structure Frame Shall Be Made From G.I. Pipe Minimum Of80nb “C” Class Welded With M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick.The Handle Frame Be Minimum Of 32Nb Shall Be Made From “C” Class G.I. Pipe.Closing Caps Shallbe Madeup Ofhigh Quality Fiber Reinforced Plastic Material.High Tensile Steel With Galvanized Nuts And Bolts Shall Be Used For Assembly. Thepowder Coating Shall Be Done With Pure Polyester Powder Ackzonoble/ Berger/Nerolac Paints With 60 To70 Micron Thickness Complete In All Respect Includingfixing The M.S. Holdfast In Cement Concrete To Hold The Whole Structure, Under Thedirections Of Engineer-In-Charge Tofulfill Thefunctional Requirement. , Doublestandingtwister Providing And Fixing Of Double Twister Standing Of Size Not Less Than 1500Mm(Length) X 600Mm (Width) X 1300Mm. (Height), To Enhance Flexibility Of Waist. Themain Structure Frame Shall Be Made From G.I. Pipe Minimum Of 100Nb “C” Classwelded With M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick. The Handleframe Is Minimumof 25Nb Shallbemade From“C” Classg.I.Pipe.The Twisterplate To Be Fitted On The Bottom Frame Shall Be Made Up Of M.S. Round Plate Ofminimum Size Ø250mm And 10Mm Thick. Closing Caps Shall Be Made Up Of Highquality Lldpe/Fiber Reinforced Plastic Material. High Tensile Steel With Galvanizednuts And Bolts Shall Be Used For Assembly. The Powder Coating Shall Be Done Withpure Polyester Powders From Ackzonoble/ Berger/ Nerolac Paints With 60 To 70Micronthicknesscompleteinallrespectincludingfixingthem.S.Holdfast Incement Concrete To Hold The Whole Structure, Under The Directions Of Engineer-In-Chargetofulfillthefunctionalrequirement. , Standingseatingtwister Providing And Fixing Of Seating & Standing Twister Of Size Not Less Than 1700Mm(Length) X 540Mm (Width) X 1250Mm. (Height), To Enhance Flexibility Of Waist.Suitable For People Of Different Ages Except Children. The Main Structure Frame Shallbe Made From G.I. Pipe Minimum Of 100Nb “C” Class Welded With M.S. Round Baseplate At Least Ø250 Mm & 10Mm Thick. The Bottom Frame Of The Seating & Standingtwister Be At Least Of 32 Nb, 50 Nb, And 25 Nb Shall Be Made From“C” Classg.I. Pipe.The Handle Frame Of Seating & Standing Twister Of Minimum 25 Nb & Foot Restingframe Of Seating Side Shall Be Made From “C” Class G.I. Pipe Minimum Of 25Mm Nb.The Twister Plate To Be Fitted On The Bottom Frame Shall Be Made Up Of M.S. Roundplate Of Minimum Size 250 Mm Diameters And 10Mm Thickness. Closing Caps Shall Bemade Up Of High Quality Lldpe/Fiber Reinforced Plastic Material. High Tensile Steelwith Galvanized Nuts & Bolts Shall Be Used For Assembly. The Powder Coating Shallbe Done By Pure Polyester Powder Of Ackzonoble/ Berger/ Nerolac Paint With 60 To70 Micron Thickness Complete In All Respect Including Fixing The M.S. Holdfast Incement Concrete To Hold The Whole Structure, Under The Directions Of Engineer-In-Chargetofulfillthefunctionalrequirement. , Pushupbars Providing And Fixing Of Push Up Bars Of Size Not Less Than 1800Mm (Length) X680mm (Width) X 1550Mm. (Height), To Enhance The Strength And Stamina Of Thebody. The Main Structure Frame Shall Be Made From G.I. Pipe Minimum Of 100Nb“C” Class Welded With M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick. Thehandle Frame Minimum Of 25 Nb Shall Be Made From “C” Class G.I. Pipe. Closingcaps Shallbe Madeup Ofhigh Quality Lldpe/Fiber Reinforced Plastic Material.High Tensile Steel With Galvanized Nuts & Bolts Shall Be Used For Assembly. Thepowder Coating Shall Be Done With Pure Polyester Powders Of Ackzonoble/ Berger/Nerolac Paints With 60 To 70 Micron Thicknesscomplete In All Respect Includingfixing The M.S. Holdfast In Cement Concrete To Hold The Whole Structure, Under Thedirections Of Engineer-In-Charge Tofulfill Thefunctional Requirement. , Surfingboard Providing And Fixing Of Surfing Board Of Size Not Less Than 1150Mm (Length) X900mm (Width) X 1400Mm (Height), To Build Up The Muscle Groups Of The Waist,Enhance The Body Coordination And Flexibility. The Main Structure Frame Shall Bemade From G.I. Pipe Minimum Of 100Nb “C” Class Welded With M.S. Roundbaseplate At Least Ø250 Mm & 10Mm Thick. The Footrests Shall Be Made From High Qualitylldpe/Fiberreinforcedplasticmaterial.Hightensilesteelwith Galvanized Nutboltsshallbeusedforassembly.The Powdercoating Shallbe Donewith Purepolyester Powder Of Ackzonoble/ Berger/ Nerolac With Minimum 60 To 70 Micronthicknesscompleteinallrespectincludingfixingthem.S.Holdfastincementconcrete To Hold The Whole Structure, Under The Directions Of Engineer-In-Charge Tofulfillthefunctionalrequirement. , Situpboarddouble Providing And Fixing Of Sit Up Board Double Of Size Not Less Than 1580Mm (Length) X1400mm (Width) X 680Mm (Height), To Enhance The Flexibility Of Whole Body. Themain Structure Frame Shall Be Made From G.I. Pipe Minimum Of 100Nb “C” Classwelded With M.S. Round Base Plate At Least Ø250 Mm & 10Mm Thick. The Remainingframe Of The Sit Up Board Minimum Of 32Mm Nb Shall Be Made From “C” Class Gipipe. The Powder Coating Shall Be Done With Pure Polyester Powder Ackzonoble/Berger/ Nerolac Paints With 60 To 70 Micron Thickness Complete In All Respectincluding Fixing The M.S. Holdfast In Cement Concrete To Hold The Whole Structure,Underthedirectionsofengineer-In-Chargetofulfillthefunctionalrequirement. , Sky Walker : Area : - 1.72 Mtr X 0.63 Mtr Safe Area :- 2.54 Mtr X 1 Mtr Providingand Fixing Sky Walker Made From B Class G.I. Pipe. The Main Frame Pipe Is ? 80Mm Made From C Class G.I. Pipe. The Outer Ring Of Sky Walker Is ? 32Mm Made From C Class G.I. Pipe. For Connecting The Handle Frame To Main Pipe ? 60Mm C Class G.I. Pipe Is Used. The Bottom Support Of M.S. Round Plate Of ? 250Mm X 10Mm Thickness Is Welded At Bottom. The Leg Movement Frame Is Of 50X50mmx2mm Thick Crc Square Pipe. The Handle Frame Is Of ? 40Mm Made From C Class G.I. Pipe. The Foundation Used For Fixing Is 80X40mmx3mm Thickness C-Channel. The Footrests Is Made From Aluminum Casting Material, Its Sizes Are 130X310x5mm. Closing Caps Made From Top Quality Frp Material With 2Mm Thickness & Plastic Cap Are Used. The Pins Used Are Made Up Of ? 25Mm Bright Bar. The Bearings Used Are 6205Zz & 6203Zz Permanent Lubricated Sealed Bering Of Reputed Make (Skf/Fag). High Tensile Steel With Galvanized Nut Bolts Are Used For Assembly. The Serclips Used For Assembly Are Of ? 25Mm. The Powder Coat Is Done By Poly Urethane & Epoxy Powder With 60 To 70 Micron Thickness , Leg Press : Area :- 0.40X1.77 Mtr Safe Area :- Providing And The Center P The Bottom Support Thickness Is Welded The Remaining Outer Frame Pipe. The Foundation Used For ? 80Mmmade From C C & 10 Mm Thickness, 25Mmx25mm. To Join The C 3Mm Thicness Is Used. The Seats Are Size 330Mmx3mm And Size 250Mmx 200Mm. The Footrests Is Made 130Mmx311.77 Mtr.-1X2.38Mtr. Fixing Leg Press Made From B Class G.I. P Pipe Is Of ? 115Mm Made From C Class G.I. Of M.S. Round Plate Of ? 250Mm & At Bottom. Is Of ? 40Mm Made From C Class G.I. Foundation Fixing Is Consist Of Three Equal Class G.I. Pipe, M.S. Round P X 3Mm M.S. Angle. Centre Pipe & Outer Frame Seamless Pipe Of Thickness Fitted On The Outer Frame Is Made Up Of Frp Material Of 300Mm Of Thickness 3Mm & M.S. Plate Of Is Used To Support It. From Aluminum Casting Material, I 10Mm & 5Mm Thickness. Pipe, Made Pipe And 250Mm, 10Mm Items I.E. Plate Of ? 250Mm Angle. ? 120Mm & Thickness 5 Support Its Sizes Are The Frame Of Footrests Consists Of ? 32Mm Made From C Class G.I. Pipe. Closing Caps Made From Top Quality Frp Material Which Is Of 2 Mm Thickness. The Inner Bushes Is Made From Seamless Pipe, Its Diameter Is 60Mm & 5Mm Thickness. The Pins Used In Are Made Up Of ? 25 Mm Hardened Bright Bar, The Bearings Used Are Of 6205Zz Permanent Lubricated Sealed Bearing Of Reputed Make (Fag/Skf). The Handles Used Are Of Rubber Grip. High Tensile Steel With Galvanized Nut Bolts Are Used For Assembly. Theserclips Used For Assembly Are Of ? 25 Mm. The Powder Coat Is Done By Poly Urethane &Exoxy Powder With 60 To 70 Micron Thickness.
