Supply Of Ball Valve Fire Safe_Non-Fire Safe For Ag_Ug Piping For Msb_Pfcc_Gds And Ff Units For Nrep Supply Of Ball Valve Fire Safe _Non-Fire Safe For Ag_Ug Piping For Msb _Pfcc_Gds And Ff Units For Nrep , Group-1 (Group Wise Evaluation) Supply Of Ball Valve-Non Fire Safe_Csfor Ag+Ug Pipping For Nerp Project Including Tpi Charges As Specified In Material Requisition. , Ball Valve Cs Int. Coated, 150,0, Api 608, Flgd,B16.5,Ff, Go, Single Reduced Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Internally Liquid Epoxy Coated Acc. To, Doc. Nr-0Zzzz-Cv-Spe-0019, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure19 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs Int. Coated, 150,0, Api 608, Flgd,B16.5,Ff, Go, Single Reduced Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Internally Liquid Epoxy Coated Acc. To, Doc. Nr-0Zzzz-Cv-Spe-0019, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure19 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs Int. Coated, 150,0, Api 608, Flgd,B16.5,Ff, Lo, Full Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Internally Liquid Epoxy Coated Acc. To, Doc. Nr-0Zzzz-Cv-Spe-0019, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure15 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs Int. Coated, 150,0, Api 608, Flgd,B16.5,Ff, Lo, Full Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Internally Liquid Epoxy Coated Acc. To, Doc. Nr-0Zzzz-Cv-Spe-0019, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure15 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs Int. Coated, 150,0, Api 608, Flgd,B16.5,Ff, Lo, Full Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Internally Liquid Epoxy Coated Acc. To, Doc. Nr-0Zzzz-Cv-Spe-0019, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure15 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs, 150,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Long Pattern, With Locking Arrangement, A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure12 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Group-2 (Group Wise Evaluation) Supply Of Ball Valve- Fire Safe_Csfor Ag+Ug Pipping For Nerp Project Including Tpi Charges As Specified In Material Requisition. , Ball Valve Cs (Nace), 150,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., Servicenace, Category 1, A105n/A216 Gr.Wcb, A182 F316 /A351 Cf8m, Stem Ss 316, Ss 316, Seal Flexible Graphite, A193grb7m/A194 Gr2hm, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, For Sour(Nace) Service Req. Acc. To, Nace Mr0103,Nr-0Zzzz-Pi-Spe-0025 And In-043, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure3.5 Kg/Cm2(G), Design Temperature300 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (Nace+Caustic), 150,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., Servicenace, Category 1, A105n/A216 Gr.Wcb, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193grb7m/A194 Gr2hm, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, For Sour(Nace) Service Req. Acc. To, Nace Mr0103,Nr-0Zzzz-Pi-Spe-0025 And In-043, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure16.5 Kg/Cm2(G), Design Temperature120 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (H2 Ser.), 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure144.6 Kg/Cm2(G), Design Temperature1190 Deg.C, Design Pressure213.2 Kg/Cm2(G), Design Temperature280 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (H2 Ser.), 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., A105n/A216 Gr.Wcb, A182 F304 /A351 Cf8, Stem Ss 304, Ss 304, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure12.2 Kg/Cm2(G), Design Temperature340 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (Nace+Caustic), 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., Servicenace, Category 1, A105n/A216 Gr.Wcb, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193grb7m/A194 Gr2hm, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, For Sour(Nace) Service Req. Acc. To, Nace Mr0103,Nr-0Zzzz-Pi-Spe-0025 And In-043, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure35 Kg/Cm2(G), Design Temperature120 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (Nace+Caustic), 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., Servicenace, Category 1, A105n/A216 Gr.Wcb, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193grb7m/A194 Gr2hm, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, For Sour(Nace) Service Req. Acc. To, Nace Mr0103,Nr-0Zzzz-Pi-Spe-0025 And In-043, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure35 Kg/Cm2(G), Design Temperature120 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Cs (Nace+Caustic), 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, All Welds Shall Be Subjected, To Pwht., Servicenace, Category 1, A105n/A216 Gr.Wcb, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193grb7m/A194 Gr2hm, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, For Sour(Nace) Service Req. Acc. To, Nace Mr0103,Nr-0Zzzz-Pi-Spe-0025 And In-043, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure35 Kg/Cm2(G), Design Temperature120 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Ball Valve Ext. Bonnet Ltcs, 600,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, Ext. Bonnet Acc. To Bs 6364, (Non-Cold Box Application), A350lf2cl1/A352grlcb, A182 F316 /A351 Cf8m, Stem Ss 316, Ss 316, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure66.5 Kg/Cm2(G), Design Temperature70 Deg.C, Design Pressure-1.01 Kg/Cm2(G), Design Temperature-45 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked. , Group-3 (Group Wise Evaluation) Supply Of Ball Valve- Fire Safe_Ssfor Ag+Ug Pipping For Nerp Project Including Tpi Charges As Specified In Material Requisition. , Ball Valve Ss Dual, 150,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, A182f304/L A351cf3/M, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Shall Be A182 Gr.F304/304L Or, A351 Gr.Cf3/Cf8, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure110.5 Kg/Cm2(G), Design Temperature165 Deg.C, Design Pressure218 Kg/Cm2(G), Design Temperature265 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked., Shall Be Dual Certified And The, Maximum Carbon Content Shall Be 0.03% , Ball Valve Ss Dual, 150,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, A182f304/L A351cf3/M, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Shall Be A182 Gr.F304/304L Or, A351 Gr.Cf3/Cf8, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure110.5 Kg/Cm2(G), Design Temperature165 Deg.C, Design Pressure218 Kg/Cm2(G), Design Temperature265 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked., Shall Be Dual Certified And The, Maximum Carbon Content Shall Be 0.03% , Ball Valve Ss Dual, 300,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, A182f304/L A351cf3/M, A182 F316 /A351 Cf8m, Stem Ss 316, Rtfe, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Shall Be A182 Gr.F304/304L Or, A351 Gr.Cf3/Cf8, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure12 Kg/Cm2(G), Design Temperature65 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked., Shall Be Dual Certified And The, Maximum Carbon Content Shall Be 0.03% , Ball Valve Ss Dual (H2 Ser., 600,0, Api 608, Flgd,B16.5,Rf, Lo, Full Bore, Bb, Fire Safe, Long Pattern, With Locking Arrangement, A182f304/L A351cf3/M, A182 F316 /A351 Cf8m, Stem Ss 316, Ss 316, Seal Flexible Graphite, A193 Gr.B7/A194gr.2H, Springsinconel X-750, Supp. Requirements, Valve Bore Shall Be Full Bore For 1/2 To, 11/2And Single Reduced Bore For 2 & Above, Shall Be A182 Gr.F304/304L Or, A351 Gr.Cf3/Cf8, Add. Information, Documents To Be Followed, Tk-1Zzza-Pi-Spe-0005,Tk-1Zzza-Pi-Spe-0006,, Tk-1Zzza-Pi-Spe-0008,Tk-1Zzza-Pi-Spe-0009, And In-042, Vendor To Submitpressure-Temp., Rating Chart, Design Pressure44.6 Kg/Cm2(G), Design Temperature190 Deg.C, Valve Shall Have 120Mm Extended Spindle, (Measured From The Valve Bonnet) To Ensure, That The Lever Clears Valve Insulation., For Trunnion Mounted Valves Sealant /, Lubricant / Flushing Injection S, Assemblies Shall Be Provided For The, And Or Stem Seal. Refer Clause B.5.16 Of, Tk-1Zzza-Pi-Spe-0009., Valve Shall Be Suitable For, Bi-Directional Flow & Pressure Shutoff, Valve Shall Be Tested In Preferred And, Non Preferred Flow Direction., Preferred Flow Direction Shall Be Marked., Shall Be Dual Certified And The, Maximum Carbon Content Shall Be 0.03% => Limited
