Supply And Fixing Fire Fighting System Work In 80 Feet Community Hall , Newai. , Works , Providing, Fixing, Jointing, Testing & Commissioning Of Heavy Duty Ms C Class (Heavy) Pipes Conforming To Is 3589 / 1239 Part-I For Hydrant And Sprinkler Applications Including Cutting, Screwing, Welding Etc. & Forged Steel Fittings Like Elbows, Tees, Tapers, Reducer, Gaskets Etc. Fixing The Pipe On The Wall/Ceiling With Suitable Clamps, Hanger And Nuts Bolts Including Cutting Hole And Chase In Brick Or Rcc Walls/ Slab And Making Good The Same. Complete With Painting Of One Coats Of Red Oxide And Two Or More Coats Of Synthetic Enamel Paint Of Required Shade Complete As Required. (Pipe To Be Tested @ 10Kgf/Sqcm For 2 Hrs.). All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , 80 Mm Dia , 100 Mm Dia , Supplying, Installation, Testing & Commissioning Of Electrical Driven Fire Fighting Duty Jockey Pump As Per Tac And Is 12469-1988., Factory Assembled In Pump Make Oem Suitable For Automatic Operation And Consisting Of Following Details Given As A, B, C, D, E,F And G (A) Horizontal End Suction Single / Multi Stage Centrifugal Back Pull Type Pump Complete For Delivery Of Below Mentioned Discharge And Head (B) Material Of Construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - Ss 410, Packing - Mechanical Seal (C) Squirrel Cage Induction Motor (Ie-3 Class) Suitable For 3 Phase,415 V, 50 Hz, Ac Supply , Class -F Insulation, Synchronous Speed Not Exceeding 2900 Rpm, T.E.F.C Confirming To Ip:55 , Of Required Hp Suitable For The Above Pump ,Along With Flexible (Love Joy Type) Coupling , Coupling Guard Complete In All Respect . (D) Common Bed Plate Fabricated From Mild Steel Channel For Installation Of Pump And Motor Including Anti Vibration Pads. (E) The Hydrostatic Tests (2 Times Of Design Operating Head Or 1.5 Times The Shut Off Head Whichever Is Higher) And Performance Tests (To Determine Developed Head, Pump Bhp And Efficiency V/S Flow) Of Pumps Along With Trip Test Shall Be Carried Out At Manufacturer’S Works In Virtual / Physical Presence Of Department’S Representatives. (F) Physical & Chemical Test Reports Of I) Pump Casing (Ii) Impeller (Iii) Shaft (Iv) Shaft Sleeve And Dynamic Balance Certificate Is To Be Submitted By Oem (G)Suitable Size Reinforced Cement Concrete (M-30) Foundation With Foundation Bolt, Nozing Angle Of Size 40Mm X40mm X5 Mm ( Cost Of Rcc Foundation To Be Paid Extra ) All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr .73.3.1 180 Lpm Suitable For 88 Mtr Multi Stage , Supplying, Installation, Testing & Commissioning Of Electrical Driven Fire Fighting Duty Pump As Per Tac And Is 12469-1988., Factory Assembled In Pump Make Oem For Sprinkler / Hydrant Applications Suitable For Automatic Operation And Consisting Of Following Details Given As A, B, C, D, E, F, G And H. (A) End Suction / Horizontal Axially Split Casing Volute Type Single / Multi Stage Centrifugal Pump Complete For Delivery Of Below Mentioned Discharge And Head (B) Material Of Construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - Ss 410, Packing - Mechanical Seal (C)Pump Shall Be Capable Of Furnishing Not Less Than 150 % Of Rated Capacity At A Head Not Less Than 65 % Of The Rated Head. The Shut Off Head Shall Not Exceed 120 % Of Rated Head (D) Squirrel Cage Induction Motor (Ie-3 Class) Suitable For 3 Phase, 415 V, 50 Hz, Ac Supply , Class -F Insulation, Synchronous Speed 2900 / 1500 Rpm, T.E.F.C Confirming To Ip:55 , Of Required Hp Suitable For The Above Pump ,Along With Flexible (Love Joy Type) Coupling , Coupling Guard Complete In All Respect . ( E) Common Bed Plate Fabricated From Mild Steel Channel For Installation Of Pump And Motor Including Anti Vibration Pads. (F) The Hydrostatic Tests (2 Times Of Design Operating Head Or 1.5 Times The Shut Off Head Whichever Is Higher) And Performance Tests (To Determine Developed Head, Pump Bhp And Efficiency V/S Flow) Of Pumps Along With Trip Test Shall Be Carried Out At Manufacturer’S Works In Physical Presence Of Department’S Representatives. (G) Physical & Chemical Test Reports Of I) Pump Casing (Ii) Impeller (Iii) Shaft (Iv) Shaft Sleeve And Dynamic Balance Certificate Is To Be Submitted By Oem (H)Suitable Size Reinforced Cement Concrete (M-30) Foundation With Foundation Bolt, Nozing Angle Of Size 40Mm X40mm X5 Mm ( Cost Of Rcc Foundation To Be Paid Extra ). All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . 1620 Lpm Suitable For 70 Mtr Head End Suction Back Pull Type Single Stage, 2900 Rpm , Supplying And Fixing Of Pn 1.6 Butterfly Valve (Wafer Type) With S.G Iron Disc And Confirming To Is:13095 Complete With 2 No. Matching Flanges (Minimum 16 Mm Thick), Nuts, Bolts, Washers, Gaskets, Etc As Required Of Following Sizes. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . 100 Mm Dia , Supplying And Fixing Of Ss 304 Single / Double Headed Oblique Pattern Hydrant Landing Valve (Internal/External) With 75 / 100 Mm Dia Flanged Inlet & 63 Mm Dia Instantaneous Type Female Outlet Coupling With Cast Iron Wheel Complete With Abs Cap And Chain And All Accessories As Per Is:5290-93 (Type-A) In Cluding Matching Flange (14 Mm Thick), Nuts, Bolts, Washers, Gaskets, Etc As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . Single Headed With 75 Mm Dia. Flanged Inlet , Supplying And Fixing Of Flexible Hose Made With 100% Polyester, Black Epdm Internal Rubber Lining With External Coat Of Synthetic Elastomer (Is:636, Type-A) 63 Mm Dia, 15 Mtr. Long Rrl Hose Pipe With Instanteneous Type 63 Mm Dia Ss-304 Male And Female Couplings (Is:903) Duly Bound And Riveted To Hose Pipes With Copper Rivets And Ss Wire Etc. As Required.Appropriate Test Certificate/ Report With Liable Warranty Of Product/Accessories From Oem Shall Be Submitted. , Supplying & Fixing Ss-304 Short Branch Pipe Conforming To Is: 903:93 Fitted With 20Mm (Nominal Internal Diameter) Bore Nozzle, For Projecting Water In Form Of Solid Jet. The Branch Shall Have 63Mm Male Instantaneous Inlet, Suitable For Use With 63 Mm Size Fire Fighting Hoses. H.P. Tested To 21 Kgf/Cm² For 2.5 Minutes. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Supplying And Fixing Of 750 Mm X 600 Mm X 250 Mm Outdoor Application Fire Hose Cabinet Made Of 1.6 Mm Thick Ms Sheet Duly Powder Coated In Red Color Externally And White Internally With 6 Mm Thick Glazed Doors With Expanded Metal 2 Mm Thick Jali Including Necessary Locking Arrangement Suitable To Accommodate 2 Nos 15 Mtr. Long Rrl Hose And 1 No. Branch Pipe On Existing Wall / Angle Iron Frame As Required. (Cost Of Ms Structure For Mounting Frame Is To Be Paid Extra) All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Supplying And Fixing First -Aid Fire Hose Reel Drum Wall Mounted Swinging Type With Ms Construction Powder Painted In Post Office Red, Conforming To Is 884-1985 With Upto Date Amendments, Complete With The Following As Required. (A) Thermoplastic / Rubber Hose (B)20 Mm Dia Ul, Fm Bronze / Ss Nozzle With 5Mm Orifice (C)Drum And Brackets For Fixing The Equipments On Wall. (D) Connections From Riser With 20/25 Mm Dia Brass/Gm Gate Valves With Screwed End And Conforming To Is:778 Class-1 Through Forged Steel Screwed Union & M.S. Pipe. Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . With 30 M X 20 Mm Thermoplastic Hose As Per Is:12585 Type-2 And Bursting Pressure 42 Kg/Sqcm , Providing And Fixing Of 100 Mm Dia. Flanged Gun Metal Fire Brigade Suction Hose Coupling (Draw Out Connection) For Female Coupling As Per Is:902-1974 Complete With Matching Flange (Minimum 14 Mm Thick), Nuts, Bolts, Washers, Gaskets, Etc As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Providing & Fixing Stainless Steel Pressure Gauge With Dial Of 150 Mm Dia Size And Range 0 To 20 Kg/Sq.Cm With 3 / 8 Bsp Bottom Entry , Ball Valve , Ss Syphon Tube All Fittings Etc, Duly Calibrated Before Installation In Mks And Fps Units, Accuracy Level +/- 1% Including Making Drilling In Existing Ms Pipe Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Sitc Of Pressure Switches Of Pressure Range 3 To 15 Bar For Main, Jockey, Terrace Pump And Diesel Pumps, Etc. As Required ( Control Cable From Pressure Switch To Panel To Be Paid Extra ). All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Supplying And Fixing Of Pn 16 Brass/Gm Ball Valves With Screwed End, Ss Ball Including Teflon Tape Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr .25 Mm Dia. , Supply & Fixing Of Dry Powder Agent (As Per Is 4308:2019), Abc Type Fire Extinguisher (Stored Pressure Type) Conforming To Is:15683:2018 , Powder Coated Internal & External Surface Deep Drawn Cylinder Body Of Mild Steel Cr2 Grade Conforming To Is: 513, Squeeze Grip Forged Brass Release Valve With Inbuilt Safety Release Device, Diaphragm Type, 0 To 28 Bar Range Pressure Gauge, 450 Mm Long Epdm Discharge Tube, Qr Code For Product Traceability Including Fixing On Wall With Suitable Anchor Fasteners As Required Of Following Capacity. Test Certificates Of All The Parameters Along With Hydro Test & Burst Test (For Cylinder Body) Certificate From Oem / External Nabl Accrediated Lab Is To Be Submitted. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . 4 Kg , Sitc Of Pa System Operator Console Of Following Wattage To Be Installed With Conventional Fire Alarm System Complete With Following Capacity , Channel Mixing Amplifier , 1 No Cardioids Goose Neck Microphone , 1 No Professional Grade Cassette Deck/ Cd Player , 16 Zone Floor Selector Console , Equipment Rack Complete In All Respects. Pa System Shall Be Coupled To The Fire Alarm System. Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . 1X 240 Watt , Sitc Of En / Lpcb/ Ul Listed / Approved Conventional Type Hooter Cum Strobe Including The Cost Of All Accessories,Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Sitc Of En / Lpcb/ Ul Listed / Approved Conventional Type Manual Call Point Resettable Complete With Glass, Hammer And Chain Etc.Including The Cost Of All Accessories Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Supplying And Drawing Fr Pvc Insulated & Unsheathed Flexible Copper Conductor As Per Pwd Specification For Electrical Works With Isi Marked (Is:694) And As Per Is 8130 : 2013 Of 1.1 Kv Grade . Wire Should Be Made From 99.90 % Purity Copper, Class 5 Stranding In Acc. To Is:8130/Iec 60228 For Lower Watt Loss , Oxygen Free For Less Chances Of Oxidization, Insulation Pvc Type A/C/D , Flame Retardant As Per Is 10810-53, Better Amperage Rating As Per Is:3961 Part 5, In Existing Surface Or Recessed Pvc/ Ms Conduit/Casing Capping Making Connections With Copper Lugs Of Suitable Size, Ferrules,Testing Etc. As Required. Oem Must Have Its Own In House Nabl Lab Setup For All Testing Facilities For Wires. For Additional Technical Parameters Of Product / Work Refer Annexure A Attached With This Bsr 1 X 1.5 Sq.Mm , Sitc Of En / Lpcb/ Ul Listed / Approved Conventional Automatic Fire Alarm Optical/Photoelectric Type Smoke Detectors Of Photo-Optic Sensing Chamber, 12 / 24 Volt D.C., Visual Alarm Indicator (Leds) Blink - Green In Stand By And Steady - Red In Alarm Complete In All Respects With Base As Required.Including The Cost Of All Accessories Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr . , Sitc Of Wall Type Following Zone (Each Zone Accessing Minimum 20 Units (Detectors/ Devices )) Conventional Type Microprocessor Based With Lcd Display En / Lpcb/ Ul Listed / Approved Main Control Panel Fabricated From 16 Swg Crca Sheet Steel Sealed Maintenance Free (Smf) Batteries Of Min2x7ah Of 12 V Or As Required.Including The Cost Of All Accessories, Etc. As Required. All As Per Pre Approved By Engineer In-Charge. For Additional Technical Parameters Of Products/ Work , Refer Annexure A Attached With This Bsr .6 Zone , P/Laying Isi Marked P.V.C. Insulated Submersible Cable Confirming To(Is:694) And As Per Is 8130 : 2013 Of 1.1 Kv Grade . Wire Should Be Made From 99.90 % Purity Copper, Stranding In Acc. To Is:8130/Iec 60228 For Lower Watt Loss , Oxygen Free For Less Chances Of Oxidization, Insulation Pvc Type A/C/D , Flame Retardant As Per Is 10810-53, Better Amperage Rating As Per Is:3961 Part 5, Existing Pipe / Open Trench / Cable Tray / On Surface Including Making Connection Etc. As Required. For Additional Technical Parameters Of Product / Work Refer Annexure A Attached With This Bsr4.0 Sq.Mm 3 Core Flat / Round , Earth Work In Excavation In Foundation, Trenches Etc. Including Dressing Of Sides And Ramming Of Bottoms, Including Getting Out The Excavated Material, Refilling After Laying Pipe/ Foundation And Disposal Of Surplus Excavated Material At A Lead Upto 50M Suitable Site As Per Direction Of Engineer For Following Depths, Below Natural Ground / Road Top Level. In All Types Soils/ Saturated Soil Such As Moorum, Sand, Sandy Silt, Clay, Black Cotton Soil, Kankar, Etc. Depth Upto 1.5 M , Plain Cement Concrete 1:3:6 Nominal Mix In Foundation With Crushedstone Aggregate 40 Mm Nominal Sizeechanically Mixed, Placed In Foundation And Compacted By Vibrator Including Curing Complete As Per Clause 2100 Of Mort&H Specification Including All Scaffolding, Material, Labour, Machinery. , Centring And Shuttering With Plywood Or Steel Sheet Upto Twostories ( Each Story Of Height Upto 3.5 Metre From Floor Level) Includingstrutting, Propping Etc. And Removal Of Form For : Walls (Any Thickness) Including Attached Pilasters, Buttresses, Plinth And String Courses Etc. , Providing And Laying Structural Plain/ Reinforced Cement Concrete (Design Mix) Of Specified Grade In Substructure At All Levels Using Concrete Mixer And Vibrator, Including Cost Of Form Work, As Per Drawing And Technical Specifications Complete As Per Clause 1500, 1700 And 2200 Of Mort&H Specification Including All Material, Labour, Scaffolding Etc. Pcc Grade M -25
