Tender For Development Of Taluk Hospital Malayinkeezhu Furniture Works, Thiruvananthapuram-Kerala

Tender For Development Of Taluk Hospital Malayinkeezhu Furniture Works-2 Revolving chairs Medium back chair :-The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly.Lumber support made up of injection moulded in black P.P and upholstered with PU foam. Lumber support size 16 cm (W) x 9 cm (H) at fixed position Size of back shall be (W)-55cm, (H)-58.0cm & size of seat shall be (W)-50 cm x (D)-44.0cm. Armrest is fixed arm rest. The arm top is made of soft moulded PU .The mechanism of chair shall have following features:360 degree revolving type, Synchro 1 mechanism, Tilt tension adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 95 +/- 5 mm. The pedestal shall be made of nylon. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in PP . Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 102.5 to max 111.5 cm. Seat height - min 44.5 cm to max 53.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards.The product shall be of approved make and colour. The model shall be Wipro or equivalent. 3 Airport chair Three seater perforated metal bench -Cross beam and Leg shall be powder coated made of cold rolled steelwith 0.2 ± 0.01 cm thickness. Seat-Back shell shall be 1.2 mm thk powder coated perforated shell made from cold rolled M.S. sheet 0.12 ± 0.013 cm thickness. The Side Bar shall be made of powder-coated solid steel with embeds. The Shell shall be assembled on the Cross Beam with help of bolts . Seat width- 54.5 cm per seat. Thickness of side bars is 4.5cm & gap between seats is 2cm. Overall Dimensions shall be Seat Height - 40.6 cm, Height - 77.5cm, Width & Depth of Chair as measured from ground - Width-176.5 cm and Depth-71 cm.Dimensions tolerance / variations shall be within +/- 1 cm. The model shall be Wipro or equivalent. 4 Office table Providing and installing Main Table: Material using Top,Leg,Front panel using IS 710 BWP Marine Plywood (Make - Archid/Century/Green Ply). Lamination using 1 MM (Make Archid Lam / Merino / Century / Greenlam). The plywood with lamination shall be hot / cold press machine required.The front panel provided at an offset of 150 MM from the outer edge. Providing Key Board Tray CPU STand & Foot Rest etc. All the visible edges are covered with 2x22MM & .5x22MM PVC Edge band wherever required.The Table fully using knockdown fittings of Mini Fix System Make - Ebco. Providing 7.2 MM Golden Steel Beeding on the front panel of the same (Size considered: 150x75x75cm) 5 Visitors chair Visitor chair (single):Providing & installing in Position Medium Back Visitor Chair with the following specifications. Seat & Back shall be Fabric upholstered/Mesh Back with 100% Polyester and weighing 320 GLM. Seat Foam shall be made out of PU foam with a density 50-60 Kg/m. Base shall be Mild Steel 4 Legged base powdercoated mounted on PVC bush. The Back rest shall be of dimension 610mm (H) X 425mm (W). Seat Size shall be of dimension 455mm (W) X 480mm (D). The product shall be BIFMA compliant 6 EXAMINATION TABLE SS 304 Features, Specification and Accessories : Backrest position achived by Ratchet Mechanism. Two sectional top made of SS304 sheet with 1mm thick. SS tubular frame made up of SS 304 round Pipes Ø32mm Round Pipe 18G Thickness for Legs and horrizontal cross pipe of Ø25mm round Pipe of 18 thickness. IV Stand Provinsion Provided. Overall size(Approx.): 1860 L mm x 540 W mm x 810 H mm Mattress 2 thickness& 32 density standard 7 Steel rack Supply and installing steel Slotted Angled Iron Rack with 6 Pannel (Size considered here: 1800x900x380 cm) 20 g 8 Almirah Material using IS 710 BWP Marine Ply Wood (Make - Archid/Century/Green Ply) Lamination using 1 MM (Make Archid Lam / Merino / Century / Greenlam). The ply wood with lamination shall be hot/ cold press machine required.Interior lamination using .8 MM (Make : Archid Lam / Merino / Century / Greenlam).All the visible edges are covered with 2x22MM & .5x22MM PVC Edge band wherever required. Back Panel using 9MM thick BWP Grade marine plywood IS 710 grade marine ply wood with .8 MM thick interior lamination. Hardware using 90 Degree Soft Close Hinges , Multipurpose lock, D Handles etc Make - Ebco. Unit fully installed by knockdown fitting - Minifix system Make - Ebco Size vary from Length 80cm -240cm, Width 45CM, Hight 90cm to 210cm. Size considered here 90x45x210cm x 28 Nos 9 PATIENTS REVOLVING STOOL FULL SS 304 Features, Specification and Accessories : Round revolving top, Ø300mm, made of SS304 sheet of 1.2mm thickness. Four legged stool, made of Ø25mmSS304 round tubes of 1.2mm thickness, mounted on central base pipe of Ø50mm SS304 round pipe with 1.6mm thickness. Height adjustable by screw thread rod mechanism. Overall size(Approx.): 350 L mm x 350 W mm x 520- 635 H mm 10 BED SIDE LOCKER ECONOMY FULL SS304 Features, Specification and Accessories: Made of SS304 tubes and sheets. Top made of SS 304 sheet with 1mm thick. Frame made of 25X25mm SS square pipe with 1.2mm thick also provide verical tubular support. Provided with one storage box and a door made of SS304 sheet with 1.2mm thickness. Overall size(Approx.) : 400 L mm x 400 W mm x 810 H mm. 11 High back chair(x-ray department) Chair -Highback :- The seat shall made up of plywood and moulded polyurethane foam upholstered with fabric. Backrest assembly is of injection moulded plastic with black mesh fabric and height adjustable lumbar support pad and adjustable headrest. The moulded polyurethane foam for seat is with density=50-55 kg/m ³.The dimensions of seat shall be- 48 cm(W) x 45 cm(D) and of back shall be 46.5 cm(W) x 51.5 cm(H). Armrest has button operated height adjustment.The arm top is made of soft moulded PU with MS embeds. The mechanism of chair shall have following features:360 degree revolving type, Synchronous 1 Mechanism.The chair shall be provided with Class 4 pneumatic height adjustment which shall have stroke of 112 mm. The pedestal shall be injection moulded in black GF nylon and fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. The cushioned head support is adjustable in height and angle for optimum user comfort.Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 92.5 to max 103.0 cm. Seat height - min 41 cm to max 51.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards.The upholstery shall be fabrics with 100% polyester.The product shall be BIFMA compliant. The product shall be of approved make and colour. The model shall be Wipro ,Godrej or equivalent. 12 HOSPITAL BED ECONOMY (PLANE TOP) Features, Specification and Accessories : Plane top MS Hospital bed. Platform made of perforated Single section CRCA MS Sheet of 1.2mm thicknesss. Head and foot bows made of MS CR round tubes of Ø32mm with 1.2mm thickness with vertical tube support. Two provisions of SS IV pole towards corners positioned diagonally. All MS parts chemically Pre-treated and Epoxy powder coated. Frame size(Approx.): 1900 L mm x 900 W mm x 560 H mm Mattress(28 density) 13 Office executive table Providing and installing Examination Table: Material using Top,Leg,Front panel using IS 710 BWP Marine Plywood (Make - Archid/Century/Green Ply). Lamination using 1 MM (Make Archid Lam / Merino / Century / Greenlam). The plywood with lamination shall be hot / cold press machine required.The front panel provided at an offset of 150 MM from the outer edge. Providing Key Board Tray CPU STand & Foot Rest etc. All the visible edges are covered with 2x22MM & .5x22MM PVC Edge band wherever required.The Table fully using knockdown fittings of Mini Fix System. Providing 7.2 MM Golden Steel Beeding on the front panel of the same Size: 150X75X75CM (Including 1 Mobile pedestal unit) 14 Providing and installing curtain rod frame with curtain cloth. Curtain rod using Aluminium frame with cloth upto a height of 220CM.

INR 2950 /-

INR 50000.0 /-

INR 28.11 Lakhs /-