Tender For Miscellaneous Civil And Electric Work Required In Training Hall For Excellence Centre, Ccas. - 1 Earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 Sqm on plan including disposal of excavated earth up to 50 Mtr. and lift up to 1.5 Mtr. disposed soil to be levelled and neatly dressed : All kinds of soil 2 Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal ofexcavated earth, lead upto 50m andlift upto 1.5 m , disposed earth to be levelled and neatly dressed : All kinds of soil 3 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils 4 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar. 5 Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead: Of area 3 square meter and below. 6 Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 7 Removing aluminium/Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. 8 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 9 M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 10 Providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg ofVG-40 (30/40 )grade and 0.30 Kg/Sqm. OfVG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineer-in-charge. 11 Grading roof for water proofing treatment withwater proffing compoundCement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 12 Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 13 Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : For area of each slab from 2001 to 5000 Sq.Cm 14 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). 15 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 16 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :25 mm thick 17 Finishing with neat cement (punning). 18 M-40,80mm thick to be used in medium- traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 0.5 to 2.0 MSA for a design life of 20 years.) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc Category A Denated units to key into each other on four faces zigzagshape as per IRC SP 63:2004 19 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) 20 Grinding of existing floor with60, 80, 120 and360 No. Carborundum stoneincluding cost of wax polishing complete : 21 Providing and fixing of false ceiling with grid of M.S.tube section of size 19mm X 19mm and with a wall thickness of 1mm+/- 0.2mm.The side pipe and the intermediate pipes is fixed to the roof from the top with the help of ceiling angles/wire grid shall be covered by the uPVC profile section of size 6mm X 250mm with wall thickness of 0.80mm +/- 0.2mm,with the help of self tapping screw of 6mm X 13mm, 6mm X 19mm.Necessary cutouts for electric connections, lighting, air conditioning etc, shall be provided at required place. The perimeter edge shall be covered by extruded PVC corner beading section of size 9mm X 28mm or 25mm X30mm with a wall thickness of 1mm+/-0.2mm fixed by applying cynoacrylic adhesive complete as per manufacturer’s specification and direction of Engineer-in-charge. 22 Providing and fixing of wall paneling on grid made out of PVC profile section of size 21x17mm with a wall thickness of 1.5mm+/-0.2mm,fixed on the existing wall with wood screw of size 50mm X 8mm with rowel plug at a spacing of 900mm center.uPVC profile section of size 150mm X 10mm with a wall thickness of 1.0mm+/-0.2mm to be fixed on the grid by self tapping screw of size 19mm X 6mm.Necessary cutouts for electrical connection to be provided at required places. The edge and periphery, finally to be covered by extruded PVC beading section of size 28mm X 12mm with a wall thickness of 1.0mm+/-0.2mm complete as per manufacture’s specification and direction of Engineer-in-charge. 23 Providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and thedirections of Engineer- in – charge .(Glazing and paneling to be paid for separately). (a)Forfixed portion,: Polyester Powder coating aluminum( minimum thickness of powder coating 50 micron) 24 ...do...For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).Polyester Powder coating aluminum( minimum thickness of powder coating 50 micron) 25 Extra for shutters of slidingaluminum windows 26 Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides. 27 Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.) With glass panes of 4.0 mm thickness ( weight not less than 10.0 kg/sqm) as per IS : 2835. 28 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 29 Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-chargePolyester powder coated minimum thickness 50 micron aluminium . 30 Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge.Polyester Powder coating aluminum( minimum thickness of powder coating 50 micron) 31 S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. 32 Providing and fixing Horizontal blinds /Venation blindshall be cold rolled formed U shape 23 mm high x 25 mm wide with flanged edges. It shall be made of heavy gaze 0.56 mm galvanized steel, Slates shall be made of virgin Al. alloy (having 3.5 – 4.5% of Mg. Content of width 25 mm. The slat shall have dust guard paint coating, the chord lock shall be of thick tomized steel and shall be securely attach in the head rail. It shall provide locking arrangement of the cord. Tilt rod shall be made of galvanized steel it shall have a D shaped with an average cross section with diameter of 6 mm to achieve minimum torsional deflection. 33 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeNew Plastered Surface (three or more coats) 34 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work 35 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Old work (One or more coats ) 36 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : One or more coats on old work. 37 Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.Hot finished welded type tubes. 38 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required.0.63 mm thick with zinc coating not less than 275 gm/m2 39 Repair to damaged RCC slabs, beams and columns etc for strengthening with cement mortar 1 : 2 in following steps :-Choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried.(ii)Applying Epoxy primer on the exposed steel bars. (iii)Applying Epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush. (iv)Speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day. (v) Plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete. (vi) Cure the plastered surface for 15 days, All work including scaffolding etc. complete in all respect. 40 Diluting and injecting by hand operated pressure pumps chemical Emulsion timber ground treatment [TCGT] in ratio 1: 2 as per manufacturers specification for POST CONSTRUCTIONAL Anti-termite treatment (as per IS 6313) part - III 1971 as amended from time to time) (excluding the cost of chemical emulsion): Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/Lindane(in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downwardangle of 45degree at 150mm centre to centre and sealingthe same. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. 41 P & F White Vitreous China Double Syphonic European W.C. (I.S:2556Mark) with mounted W.V.C. flushing cistern of (IS : 2556 Mark) of 10 litre capacity complete with all necessary internal fittings including cutting and making good the wall and floor. 42 P & F C.P. Health Faucet with 1Mtr. Long Tube & Hook of approved make and heavy as per direction of Enginner-in-Charge 43 P & F water closet Seat Covers with brass hinges complete :Solid PVC (IS 2548 marked) grade-I white for EWC. 44 Providing and fixingSuperior quality CP Brassfittings of approved make as per direction of Engineer-in-charge: Two way Bib Cock 15 mm nominal size 45 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) 46 P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe withC.P. Brass nuts upto length, 600mm. 47 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 550 mm x 400 mm 48 Providing & Fixing Commercial Ply as per IS 710 : 1976 BWR of approved make for making wardrobe/shelves and other furniturewith fevicol & nails completeas per approved by engineer in charge. 12 mm thick 49 Providing and fixing of double leaf steel shutterfor cupboard, the frame is made of pressed steelISI section 80x25 mmx1.25 mm thickwith 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc completeincluding applying priming coat of approved steel primer of red oxide zinc chromate andspray painting in approved shade with decopaint of approved quality complete as per direction of Engineer In Charge 50 Labour charges for dismantling of surface PVC/ Steel conduit including wiring in conduit, conduit fittings and depositing the same with listing of material in store. 51 Labour charges for dismantling of surface/ recessed switch board of any size and depositing the same with listing of material in store. 52 Labour charges for dismantling of switch accessories like switch,socket, ceiling rose, holder and depositing the same with listing of material in store. 53 Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and1.5 sq.mmnominalsize FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & its all accessories( J.B. , Bends etc.) , round tiles,18SWGHotDippedGalvanized ModularBox withearth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pinceilingrose/lampHolder/3pinconnector,screwsetc, making connections,all as per pre approved by Engineer in charge, testingetc.completeasrequired. Forspecificationofcopper Conductor,Phenolic Laminated sheets & Electrical/ Wiring accessories referChapterE-04,E-05&E -07 .For additional technicalparametersofproducts/work, refer Annexure A attached with this BSR . 54 (a) S.P. (up to 3 mtr.) 55 (b) M.P. (up to 6 mtr.) 56 (c ) L.P. (up to 10 mtr.) 57 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specificationforelectricalWorkswithISI marked1.5 sq.mmnominalsizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and1.5 sq.mmnominalsize FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit&itsallaccessories(J.B.,Bendsetc.),roundtiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modularswitch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, makingconnections,testingetc.completeasrequired. For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07.For additional technical parameters of products/ work refer Annexure A attached with this BSR . 58 Medium point (up to 6 mtr.) 59 On board 60 Short point (up to 3 mtr.) 61 S&Ffollowingsizes(dia.)ofISImarkedMMS(IS:9537P-III) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. All relative and latest acceptancetests reports byanyNABLaccreditedlabfortheconduitshallbesubmitted before execution & All as per pre approved by Engineer in charge. Foradditionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR . 62 (a)25 mm 63 (b)20 mm 64 SupplyinganddrawingFRPVCinsulated&unsheathed flexiblecopperconductorasperPWDspecificationfor electricalWorkswithISImarked(IS:694)andasperIS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99%puritycopper,class5strandinginacc.toIEC 60228for lowerwattloss,oxygenfree(<10ppm)for lesschancesofoxidizationandhighersilvercontentfor givesbetterconductivity,insulationPVCtypeA,flame retardantasperIS10810-53,betteramperageratingas perVDE0298part4, ,inexisting surfaceorrecessed PVC/MSconduit/casingcappingincluding allasperpre approved by Engineer in charge,making connections, etc. asrequired.OEMMusthaveitsowninhouseNABLlab setupforalltestingfacilitiesforwires.Foradditional technical parameters of products/ work, referAnnexure A attached with this BSR . 65 (a)2 x 1.5 sq.mm 66 (b) 2 x 2.5 sq. mm. + 1x1.5sqmm 67 (c) 2 x 4.0 sq. mm. + 1x2.5sqmm 68 (d)4 x 4.0 sq.mm 69 Providing&FixinginpositionframemadeoutofM.S.angle (riveted or welded) as per IS: 2062-2011 finished withtwocoatsofredoxideandtwocoatsofenamel paint including cutting, welding, holes etc.of following sizesasrequired.Alldrawingasperpreapprovedby Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 70 (a)25mmx25mmx 3mm 71 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure A attached with this BSR 72 Providing & Fixing ofof ISO certified company madeMultiple socket with surge and spikes protection cartridge not less then 5 KV as per PWD specification for electrical Works with minimum four nos. universal 6 A sockets, one 6 A switch and 3 pin company fitted plug top and 3 core multistrand copper lead minimum 1.5 mtr. including making connection etc as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 73 P & F paper phenolic resin bondedlaminates confirming to IS : 2036 - 1995 for boxes/ frames including making holes for switches etc, with brassscrews,washers/zincplated nutandboltsasrequired.For additional technical parameters of product / work refer Annexure A attached with this BSR 74 6.4 mm thick 75 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 76 Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) conforming to (IS:12640-1)/ IEC 61008 -1 , rated 4 KV impulse withstand voltage truly current operated and shall operate on CBCT mechanisum, provision for pad lock,min. operation 10,000 upto 63 A rating and5000 for 100 Aratingand minimum phase termination capacity of 35 sq.mm. rigid wire, IP 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 77 Two pole 30 mA sensitivity (16/25 A rating) 78 Four pole 30 mA sensitivity(40 A rating) 79 Four pole 30 mA sensitivity (100 A rating) 80 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 81 (a)Double pole isolator 30 A / 40 A rating 82 (b)Double pole isolator 63Arating 83 (c)Four pole Isolator, 100A/80A rating 84 Providing & Fixing of Recessed/surface mounting heavy duty horizontaltypeDoubleDoor(Metal/Glazed)Distributionboard with Metal end box made out from Galvanized steel / CRCA sheet notlessthen1.2mmthick conformingtoIS-8623-1&3/ IEC 61439- 1 & 3, powder painted completewith reversibledoor (for double door DB only )100 amp.insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnectingwireset ofsuitableratinganddinbar,masking sheet,making internal DBterminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated labtypetestreports &AllasperpreapprovedbyEngineerin charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 85 Glazed door (Singlee phase) IK-09 and IP-43 with Metal end box 12Way (12+2) 86 Glazed door (Three phase) IK-09 and IP-43 with Metal end box 12way 87 Providing&Fixingof extradownrodof15mmdia.ERW(Electrical resistancewelded)of1.6mmnominalthickmediumdutysteel pipe including cutting, threading, drilling, fixing quarter pin etc as reqd.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with thisBSR . 88 17.4 Providing & Fixing of IP20, 2x2 LED Surface/ Recessedmounting Mid power SMD type LED Light fixturenotlessthan50mmhousingdepthmadefromCRCAsheetsteelhousing,highpurity/ transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection(Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI>80 ,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shallbe submitted.All asper preapproved byEngineer in charge.AllasperpreapprovedbyEngineerincharge. Foradditionaltechnicalparametersof products/ work, refer Annexure A attached with this BSR . 89 Providing&Fixingofmodulartype120WStepFanregulatordulyISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required. Foradditionaltechnicalparametersofproduct/workrefer Annexure A attached with this BSR 90 5 step fan regulator 2 Module 360 dgree rotating 91 Providing & Fixing of 400mm SweepBLDC technology Oscillating type Wallmounting/Pedestaltype fanswithThreespeed,ONand OFF position,DoubleWallbearingwith frontandback120ormore ribs guard; Three no.blades, noise level should be <= 75 dB,including fixing withanchorbolts,makingconnectiontestingetc.asrequired.(With Remote ) All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 92 Wall mounting type with Service value 2.0 CMM /W, Min. Air Delivery 71 CMM 93 Providing&Fixingof BEE Starratedcopperwoundeddoubleball bearingcapacitorstart,aluminiumbody&Metallic bladeceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e.ISImarking)withdownrodupto80cmwithsecondarysupport safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All asperpreapprovedbyEngineerincharge. Foradditionaltechnical parameters of products/ work, refer Annexure A attached with this BSR . 94 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) 95 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Coppercable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withelectrolytic gradeCopper made of copper rodsconfirming to IS 613-1964, of purity >99.7 %,Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure A attached with this BSR 96 6.0 Sq. mm 3 core 97 Supply,Installation,TestingandComissioningof InvertertypeAir Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R- 410GreenRefrigerant,wirelessRemotecontrol,suitableforworking between 230V +/- 10% with low & high voltage cutoff and50 hz , single phaseACsupply capableofperformingcooling,dehumidification,air circulation of following capacity with Scroll / rotary compressor. All as perpreapprovedbyEngineerincharge. Foradditionaltechnical 98 1.5 TR ISEER not less then 3.8 99 2.0 TR ISEER not less then 3.8 100 Providing&LayingP.V.C./XLPEinsulated&P.V.C.sheathedArrmoured Aluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure A attached with this BSR 101 50.0 Sq. mm 3.5 core 102 Supply,FixingandtestingoffollowingcapacityISOcertifiedcompanymade wall mounted stabilizer having output voltage variation from 200 V to 250 V(+/-5%) with input voltage variation from 170 V to 260 V, time delay facility from 2 to 4 minute and high cutoff at 270 V with providing of 16 Amp /20 Amp Industrialplug top making connection etc complete inallrespect. AllasperpreapprovedbyEngineerincharge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR 103 4 kVA 104 5 kVA 105 PlateEarthing asperIS:3043withHotdippedG.I.Earthplateofsize 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20mm dia. G.I. B class watering Pipe ,including all accessories likenut,bolts,reducer,nipple,wiremeshedfunnel,andHeavyduty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodyingthepipe completewithalternatelayerssaltandcoke/ charcoal,testingofearthresistanceforvalueof5ohmsorless as required & must record by engineer in charge during site visit and ensure toenterinmeasurmentbook.AllasperpreapprovedbyEngineerin charge. Foradditionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR . 106 Providing & Fixing ofof M.S. J- hook of standard design made out of 16 mmdia.M.S.roundbarandfixedwith cementconcretemortarwith requiredsupportasrequired.AllasperpreapprovedbyEngineerin charge. Foradditionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR . 107 Supplyingandmakingoneendterminationwithheavy dutybrasscompressiongland(asperIS12943-1990) SIBGtype,heavydutyaluminiumlugs(asperIS8309- 1993&IS8337-1976)dulycrimpedwithcrimpingtool, PVCtape asperPWDspecificationforelectricalWorks etcforfollowingsizeofArmouredPVCinsulated&PVC sheathed/XLPEaluminiumconductorcableof1100volt gradeasrequiredofsize.Allasperpreapprovedby Engineerincharge. Foradditionaltechnicalparameters ofproducts/work ,referAnnexureAattachedwith this BSR . 108 3.5 x 35.0 sq.mm 109 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .8 SWG G.I. ( Hot Dipped) Wire 110 Up to 35 Sq.mm fixed with 25 mm x 2 mm thick suitable length red oxide andenamel painted MS clamp and base, pvc rawl plug and screws of sufficient sizewith spacing 0.6 Mtr. Between Clamps.
