Tender For Repair And Painting Work In International Hostel, Rca Campus. Repair And Painting Work In International Hostel, Rca Campus. - 1 Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead: Of area 3 square meter and below. 2 Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead : For thickness of tiles 10mm to 25mm. 3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level : M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 4 P&F 1st quality standard White, gray, Ivory, fume red brown, light green ,light blue and other light shades glazed tiles of ISI marked ( IS : 13753 ) of size 300 mm. x 200 mm.in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (Excluding the cost of cement plaster on walls and pillars)Extraforusingsize above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finishedtiles in place of 300mm x 300mm size. 5 P and F 1st quality MAT finished ceramic tiles size 300x300mm confirming to IS : 13753 colour such as white, grey ,ivory, fume red brown, light green, light blue and other light shades in floor, steps, pillars etc. laid on a bed on net cement slurry including nicely finished joints using water proof joint filler powder ( Unitile or Roffee make ) and finished with flush pointing in white cement mixed with pigment to matched the shade of tile complete ( including the cost of cement mortar bed 1:4) Extraforusingsize above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finishedtiles in place of 300mm x 300mm size. 6 Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 7 Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : For area of each slab from 2001 to 5000 Sq.Cm 8 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure A:30 mm thickCommercial Veneer both side 9 Extra for providing IS 1341-1992marked Stainless Steel butt hinges instead of black enamelled M.S. butt hinges with necessary screws. (Shutter area to be measured). 10 Extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. 11 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 12 Structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: 13 Fine grinded Gangsaw cut 30-35 mm thickstone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement :4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI : Red sand stone (Karauli stone) 14 Plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 20mm thick . 15 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) 16 Providing and fixing double scaffolding system on the exterior side, upto five story made with 4 wooden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. The scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of EI.The elevation area of the scaffolding shall be measured for payment. The payment will be made once irrespective of duration of scaffolding.Note : This item to be used for maintence work judicially 17 Renewing glass panes,with putty and nails wherever necessary : Float glass panes of thickness 4 mm 18 Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. 19 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete : New Plastered Surface (three or more coats) 20 Applying priming coat with ready mix pink or grey primer of approved brand and manufacture on wood work hard and soft wood. 21 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :One or more coats on old work 22 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :Two or more coats on new work 23 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : One or more coats on old work 24 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision : New Work 25 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision : Old Work 26 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work including prepration of base with prime putty lippy complete in all respect. 27 ProvidingandfixingEuropean typewhite glazed vitreous china Ist quality WC pan [IS: 2556mark] P or S trap including cutting and making good the wall and floor. 28 Providing and fixing water closet seat covers with brass hinges complete solid P.V.C. (IS 2548 marked) grade-I white for EWC 29 P & F Low level Flushing cistern of 10 litres capacity [ IS : 2556 mark ] of approved make with complete fittings , C.I. brackets duly painted , brass ball cock with ball [ IS : 1703 mark ], complete including cutting and making good the wall : PVC with PVC bend as per IS : 7231 30 Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap. 31 Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap. 32 Providingandfixing waste pipe with all fittings ,P.V.C. with P.V.C. nut, 32 mm 33 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)15 mm nominal size 34 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work), 25 mm nominal size 35 Making connection of G.I. distribution branch with G.I. main including all fittings , up to 25 mm. dia. 36 Providingand fixing Ball cock [IS :1703 mark] withrodandPVC ball complete Brass wt. Not less than 300 gm,15mm. 37 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore. 38 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass Long body, 15mm nominal bore weight not less than 690 gm 39 P&F C.P.Inlet connection[ Angles / Valves ] superior quality of approved make, for wash basin, Gyser etc.,C.P. Inlet connection15mm. Brass[ IS : 8931 marked] 40 P&F 15mm dia connection pipe of approved quality/ make P.V.C. pipe with C.P.brass nuts upto length 600mm 41 Providing and fixingfull way valve [IS : 778 mark] or wheel valve ofapproved make, gunmetal 15 mm. nominal bore 42 Providing and fixingfull way valve [IS : 778 mark] or wheel valve ofapproved make, gunmetal 25 mm. nominal bore 43 Providingandfixingrigid PVC pipe [IS:4985 mark] class II [4 Kg/cm2] appproved quality/make including jointing the pipe with solvent cement , rubber ring & lubricant, 110mm. dia. 44 Providingandfixingrigid PVC pipe fittings [IS:4985 mark]appproved quality/make including jointing the pipe with solvent cement , rubber ring & lubricant, 110mmdia. 45 [A] Coupler ( Socket ) 46 [B]Plain Tee 47 [C]Door Tee 48 [D]Bend 450 49 [E]Bend 87.50 50 [F] Door Bend[Top Side] 51 [G]Vent Cowel 52 [H]Plain floor trap 53 [I] Pipe Clip 54 Wiring of light point/ fan point/ exhaust fan point/ call bell point with1.5sq.mmnominalsizeFRPVCinsulatedunsheathedflexiblecopper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathedflexiblecopperearthconductor1.1kVgrade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot DippedGalvanizedModularBoxwithearthterminal,10AModular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3wayconnector,screws, makingconnections,testingetc.asrequired. Forspecificationofcopper Conductor, PhenolicLaminatedsheets& Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additionaltechnicalparametersofproduct/workreferAnnexureA attached with this BSR 55 (a) S.P. (up to 3 mtr.) 56 (b) M.P. (up to 6 mtr.) 57 (c ) L.P. (up to 10 mtr.) 58 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FRPVCinsulatedunsheathedflexiblecopperconductor1.1kVgrade and1.5sq.mmnominalsizeFRPVCinsulatedunsheathedflexible copperearthconductor1.1kVgrade(IS:694) in recessedISImarked MMS(IS:9537P -III )PVC conduit&itsISI marked(IS:3419- 1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc.asrequired. Forspecificationofcopper Conductor, Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E- 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR : On board 59 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III)PVCconduitalongwith ISImarked(IS:3419-1988)accessoriesas required in recess including cuttingthewall,coveringconduitand making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR : 25 mm 60 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductorasperPWDspecificationforelectricalWorkswithISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should bemadefrom 99.90%puritycopper,class5strandinginacc.to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization,insulationPVCtypeA/C/D,flameretardantasperIS 10810-53,betteramperageratingasperIS:3961part5, inexisting surfaceorrecessedPVC/MS conduit/casingcapping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required.OEMMusthaveitsowninhouseNABLlabsetupforall testingfacilitiesforwires.Foradditionaltechnicalparametersof product / work refer Annexure A attached with this BSR 61 (a) 2 x 1.5 sq.mm 62 (b) 2 x 2.5 sq. mm + 1x1.5 sqmm 63 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of loadand siterequirement)4KVimpulsewithstandvoltage,ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947- 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 asperIEC, minimumphaseterminationcapacityof35sq.mm., conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000upto20Aratingand10,000upto63A,5000for80A& above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR.Single pole MCB (With B/C curve tripping Characteristics)6 A to 32 A rating 64 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular boxof1.2mmthickwithearthingterminal/connectoronsurfaceorin recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16amp.socketoutlet(IS:1293)makingconnection,testing,etc.as required.Forspecificationof WiringaccessoriesreferChapter E-07 related item & For additional technical parameters of product / work refer Annexure A attached with this BSR 65 Providing & Fixing of Recessed/surface mounting heavy duty horizontaltypeDoubleDoor(Metal/Glazed)Distributionboard with Metal end box made out from Galvanized steel / CRCA sheet notlessthen1.2mmthick conformingtoIS-8623-1&3/ IEC 61439- 1 & 3, powder painted completewith reversibledoor (for double door DB only )100 amp.insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnectingwireset ofsuitableratinganddinbar,masking sheet,making internal DBterminations with copper lugs, Ferrules detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated labtypetestreports &AllasperpreapprovedbyEngineerin charge. For additional technical parameters of product / work refer Annexure A attached with this BSR :Metal door (Three phase) IK-09 and IP-43 with Metal end box , 6 Way (6+2)