Carrying Out Preventive As Well As Breakdown Maintenance And Repairing Of Chlorinator For Ascertaining Disinfection Of Different Pwss Under Mangalkote, Katwa- 1&2, Ketugram- 1&2 Block (I.E Kasiara, Paschim Gopalpur, Jogeswardihi Etc.) Under Cmd, Phe Dte.,, purba-West Bengal

Carrying out preventive as well as breakdown maintenance and repairing of chlorinator for ascertaining disinfection of different PWSS under Mangalkote, Katwa- 1&2, Ketugram- 1&2 Block (i.e Kasiara, Paschim Gopalpur, Jogeswardihi etc.) under CMD, PHE Dte., Dist.- Purba Bardhaman- 1 Supply, delivery at site and storage of Actuator Clutch Levers of Rotork make Actuator Model No. K-60 & K-150 installed in Filter Bed. 2 Supply, delivery at site and storage of Actuator Cloumn Pipe and LSD Shaftof Rotork make Actuator Model No. K-60 & K-150 installed in Filter Bed. 3 Re-winding of 3Phase 415V, 50Hz. AC Actuator Induction Motor by supply of suitable gauge copper winding wire including vernishing complete as per direction of EIC. 4 For K-60 Actuator Motor. 5 For K-150 Actuator Motor. 6 Supply, delivery at site and storage of Worm Shaft & Worm Gear set of Actuator installed in Filter Bed. 7 Supply, delivery at site and storage of Actuator Body & other Spare Parts except Actuator Motor of Model No. K 150 F10E 72rpm, Syncroset type including hand wheel & column pipe. 8 Supply, delivery at site and storage of Switch Mechanism of Wiring Diagram No. WD1000 with 4 Nos. 1NO + 1NC Switch Torque & Travel Combined Switch with Continious Local Indicator. 9 Supply, delivery at site and storage of Oil Seal Kit suitable for Rotork Make Actuator Model K 150 & K60. 10 Overhauling of existing Rotork make K60 & K150 Synchroset Actuator of 6Nos. Filter Bed including replacement of damaged Clutch Leaver, Column Pipe & LSD Shaft, Worm Shaft & Worm Gear Set. New Body with Accessories, Switch Mechanism of Wiring Diagram, Oil Seal Kit, Repaired Motor etc. by new one as stated in Item Sl. Nos. 1.01 to 1.07 above by Petrol & Steem Wash and refilling with IOCL make Servogen Gear Oil as per direction of EIC. 11 Supply, delivery at site and storage of CPU / PCB and transformer suitable forAuma make Valve Actuator installed with existing Tube Settler Sludge Valve. 12 Overhauling of existing Auma make Actuator installed with the existing Tube Settler Sludge Valve including replacement of damaged CPU/PCB & Transformer by newly supplied units as stated in Item Sl.No. 2.01 above as per direction of EIC. 13 Repairing of Control Desk Panel of Filter Bed including replacement of damaged 10 Nos. Coil Contactor, 5Nos. Over Load Relay, 15 Nos. 10Amps Fuse, 1 No. 16Amps Panel Mounted Main Switch, 15 Nos. Push Button, 15 Nos. Indicating Lamp (LED type), Total Wiring by 2.5sq.mm Copper Multistrand Flexible Wire complete as per direction of EIC. 14 Supply, delivery at site and storage as follows : 15 1.1KV grade 10Core 2.5sq.mm PVC insulated copper armoured Control Cable for 4 Nos. Settler Sludge Valve Actuator. (4 x 50M) 16 2mm sheet steel enclosed wall mounted 500mm x 700mm x 300mm depth Push Button Panel for 4 Nos. Settler Sludge Valve Actuator Operation at Filter House. 17 3 dia.GI Pipe and 3 Bend for laying of Control Cable from Settler Sludge Valve to Filter Bed House as follows : 18 3 dia. GI Pipe 19 3 dia. GI Bend. 20 Fitting fixing of newly supplied Push Buitton Panel of Item Sl.No.4.02 above inside Filter House Wall as per direction of EIC. 21 Laying of 4Nos.10Core 2.5Core newly supplied copper Ar. Control Cable from Settler Sludge Valve to Filter Bed House through under ground trench with newly supplied GI Pipe Protection of Item Sl. No. 4.03 above as per direction of EIC. 22 Making Power and Control Cable connections with Control Desk, Newly Push Button Panel of Item Sl.No.4.02 above and Actuators of Filter House by existing laid cables and newly laid control cable for Settler Sludge Valve complete with Limit Switch Setting, Close & Open both sides and Synchronising with actuator & Panel as per direction of EIC. 23 Overhauling of 150mm dia. Air Release Valve after necessary repairing of the same as per direction of EIC. 24 Overhauling of 250mm dia. Outlet Valveafter necessary repairing of the same as per direction of EIC. 25 Overhauling of 300mm x 300mm Inlet Sluice Gate after necessary repairing of the same as per direction of EIC. 26 Overhauling of 350mm dia. Back WashValve (Gate Valve) after necessary repairing of the same as per direction of EIC. 27 Overhauling of 450mm x 450mmDrain Valve (Gate) after necessary repairing of the same as per direction of EIC. 28 Replacement of existing damaged motorised based 200mm dia. Wafer type Butterfly Valve after disconnection of Power & Control connections of existing actuatorby newly supplied Actuator Operated Butterfly Valve (deptt. supply) in the existing pipe line by cutting and re-welding of existing flange including supply of new nut, bolt & gasket as per requirnment for suitable fitment of valve and also refitting of existing Actuator as per direction of EIC. 29 Supply, delivery at site and storage of 2mm thick sheet steel enclosed powder coated wall mounted Push Button Panel for 200mm dia. Motorised Butterfly Valve comprising with 3 Nos. Push Button, Red, Yellow & Green for Close, Open & Stop, 3 Nos. Indicating Lamp for Full Close, Full Open & Motor Running. 30 Add GST @ 18% 31 Add Cess @ 1%

Refer document

INR 80600.0 /-

INR 39.08 Lakhs /-