Tender For Electrification Work Of Auditorium At Balaji Market, Kota - Supply,Installation, Testing & Commissioning Of Modular Type Variablerefrigerantflow/Variablerefrigerantvolumeaircooled Outdoorunitssuitable For Cooling And Heating,Having100% Hermetic, kota-Rajasthan

Tender For Electrification Work Of Auditorium At Balaji Market, Kota - Supply,Installation, Testing & Commissioning of modular type VariableRefrigerantFlow/VariableRefrigerantVolumeaircooled Outdoorunitssuitable for cooling and heating,having100% hermetically sealed inverter type Scroll Compressor(s) withand minimum two compressors along with two Condensing fan,above 14/18 HPmodules,microprocessorbased Controller, Side / top discharge type condensing unit(s), with R-410 A Refrigerant,vibrationisolators,withsuitablefoundationetc. completeasrequired.Theunitshalldelivertheratedcapacityat AHRIConditions andwork evenat 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V +/- 10%, 3Phase,50HzACpowersupply.Theunit shallbefilledwithfirst charge of the refrigerant and ready for use as required. The EER at 100% load with AHRI conditions shall not be less than 3.5 andIncluding OEM supplied Piping connection Kit etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 2 P & F of Fire retardent flexible canvass connection made of fibreglass weave having silver grey silicon rubber coating, of height 200 mm with sufficient fold to avoid transmission of vibrationwith GI frame ,Gasket Nut Bolts for air cooling Plants/AHU/FCU etcas required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 3 Supply , Installation, Testing and Comissioning of site fabricated ducting made from aluminium sheet conforming to IS:737, Grade 31000fabricated as perIS:655 and as per approved drawings & designs including the cost of hangers, supports , angle , expansion fasteners , closed cell neoprene gasket T&P etc. as required of following thickness. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .0.80mm 4 1.00mm 5 Supplying, installing, testing and balancing of extruded Aluminium powder coated Air Diffuser and complete with Flush, 20mm flanges with PVC/neoprene gasket, anti – smudge frame and removable inner core to facilitate the adjustable of air control damper, square/round/ rectangular as required.including fixing with steel screws etc. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Supply Air Diffuser with Volume Control damper 6 Supply and fixing of acoustic lining of ducts withchemically cross link Oxide accetate foam open cell structure Acoustic Insulation with density 30 Kg / Sqm, UV protected and Class O Fire propperty Water Vapour absorption 0.002 gm / Sqcm,including cost of adhesive etc. complete in all respect.All as per pre approved by Engineer in charge.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 25 mm thick 7 Supplying, installing of external thermal closed cell cross linked polyethelene (XLPE) foam insulation made out from non-fibrous, fire retardant (FR), closed cell, tri-dimensional chemically crosslinked polyethylene foam. should be certified Class O in Fire Propagation and Class 1 in Surface Spread of Flame as per BS 476 Part 6 & Part 7 respectively in the form of sheet on ducts including cost of adhesive, tape complete as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 25mm thick 8 Supply , Installation, Testing and Comissioning of Window type Air conditionersas per BEE star ratingcomplete with copper power cable upto 3 Mtr, wireless Remote, suitable for working between 230 V +/- 10%with low & high voltage cutoff and50 Hz ,1 phaseACsupply capable of performing, cooling, dehumidification, air circulation R-32/R-410Green Refrigerantwith Scroll /rotary compressorcomplete with fixing including T&P & labour etc as required complete in all respect as specified of following capacity. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1.8 TR 9 Supply , Installation, Testing and Comissioning ofInverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and50 hz , single phaseACsupply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 2.0 TR ISEER not less then 3.8 10 Supply , Installation, Testing and Comissioning of Air Cooled Cassette typeAir conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A Green Refrigerant, wireless Remote, inbuilt drain pump, suitable for 400/230V, +/- 10% 50 Hz ,1 /3 phaseACsupply, apable of performing cooling, dehumidification,Air circulation, filteration & ventilation of following capacity with Scroll /rotary/twin rotary compressor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Inverter Type2.0 TR ISEER not less then 3.5 11 Supply,installation,testingandcommissioningoffollowing minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor,coilsection with DXCoppercoil,electronicexpansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation,Cordedremotecontroletc., suitableforoperationon single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down valve in case of fire on receivingsignalfromBMSSystem. Thecoolingcapacityofindoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .4 TR 12 Supply, installation, Testing & commissioning of VRV/VRF compatible OEM make AHU KIT including expansion valve and controller for connecting AHU with VRF. 13 Supplying and installation of high-pressure grade required size OEM make copper connectionY or T Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 14 Gas charging of VRF/VRV system with R410A refrigerant gas. Before gas charging system shall be flushed with high purity Nitrogen Gas to remove carbon content, dirt particles to make sure that there is no chance of mixing any impurity with Refrigerant Gas. Thereafter System shall be tested with Nitrogen Gas at 1.5 Times of working pressure of R410 Refrigerant Gas to ensure leakproof system. Whole system shall be Vacuumed up to 500-micron level which ensures the zero-moisture content level in piping to ensure better cooling efficiency and long life of the system. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 15 Supplying and drawing flexible / stranded bare copper conductor, PVC / XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS /EN 50288-7 in existingsurface or recessed PVC/ MS conduit/casing capping/ Cable tray / Open Duct making connections, testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for cables. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .4 core x 2.5 Sq.mm 16 Supply, installation, testing and comissioning ofinterconnectingcopperrefrigerant pipingof DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink MarkBrand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified Class O in Fire Propagationas per BS 476 Part 6 including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as required of following sizes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .41.1 mm O.D., wall thinkness ≥ 1.4mm (insulation – 19 mm thick) 17 34.9 mm O.D., wall thinkness ≥ 1.4mm (insulation – 19 mm thick) 18 22.2 mm O.D., wall thinkness ≥ 1.0mm (insulation – 19 mm thick) 19 19.1 mm O.D., wall thinkness ≥ 1.0mm (insulation – 13 mm thick) 20 15.9 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) 21 12.7 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) 22 9.5 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) 23 Providing & Fixing of IS : 4985 - 2000 Class -4 (10 Kgf / Sqcm) UPVC drain water piping withfittings (IS:7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing,support with MS hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following Nominal sizes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .25 mm 24 32 mm 25 Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia200 mm dia per running inch length 26 SITC of Interconnecting refrigerantcopper pipe forsplit/Ductable/ Casseette AC of DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink MarkBrand Printing on Hard Tubes should be present. Piping between each set of indoor & outdoor units of different sizesas per OEM requirement & specifications including class O Nitrile rubber sleeves, chase cutting, supports, making good the same with sand cement plaster etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 27 Supply,Installation, testing and commissioning ofAHU UNIT with ahu kit connectionwithindividual controller for cooling /heating type operations.The rates are including lifting,shifting, Transportationetc. (Make O General,Mitsubishi heavy & equivalent make matching with above specification) & make is to be approved by engineer incharge25 TR AHU UNIT 28 SITC of pressure switches ofpressure range 3 to 15 Bar for Main, Jockey, Terrace pumpandDiesel pumps, Etc. as Required ( Control Cable from Pressure switch to Panel to be Paid Extra ). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 29 Providing and fixing 20/25 mm dia. (PN - 1.6, Type-S1, Flanged, ISI marked) air release valve confirming to IS - 14845 : 2000 with Double Flange isolating valve (pressure rating PN 1.6) complete with 1 no. Matching Flanges (Minimum 10 mm thick),nuts, bolts, washers, gaskets etc as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 30 SITC of UL listed and FM Approved Polyethelene vane type water flow switch with actuation & delay mechanism for sensitivity in the range of 4 to 10 GPM and suitable for installation in following sizes of Sprinkler pipe for a Staticpressure rating up to 250 PSIin cluding making connections, making hole in pipe for inserting the vane etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .100 mm Dia. 31 Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class (Heavy) pipes conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applicationsincluding cutting, screwing, welding etc. & forged steel fittings like elbows, tees, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of requiredshade complete as required. (Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs.). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .100 mm dia 32 150 mm dia 33 Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class (Heavy) pipe conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applications in Existing trench with cement concrete block as supportsincluding cutting,welding etc & forged steel fittings like elbows, tees,tapers, reducer with cleaning,wrapping and coating of the pipe with 4 mm thick tar based polymaric corrosion protection tape including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrosion complete in all respect. ( Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs. & Excavation of Trench and refilling of trench to be paid extra). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 150 mm dia 34 Supplying and fixing cylindrical air vessel of continuous welded constructionfixed at riser top made of 250 mm dia, fabricated out of 8 mm thick MS sheet, 1200 mm in height withflanged connection, Provision for25 mm dia drain valve,air release valve,safety valve pressure gauge as required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint including The tank shall be installed on suitable vertical legs. The legs shall be provided with M.S. Angle of size 75 mm x 75 mm x 5 mm at the bottom. The legs shall be grouted in cement concrete foundation. as required. ( Air Release valve, Drain valve, PRV, Pressure Gauge shall be Paid Extra ). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 35 Supplying and Fixing of PN 16 Flanged Y strainer fabricated out of cast iron body, SS 304 strainer with perforated screen with 3 mm. dia holesin existing MS / GI pipe complete with 2 no. Matching Flanges (Minimum 16 mm thick),nuts, bolts, washers, gaskets etc as required of following sizes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 200 mm dia 36 Supplying and Fixing of PN 16 Cast Iron Dual Plate Wafer Type Check Valve / Non return valve with SS / Bronze flap complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets,etc as required of following sizes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 100 mm dia 37 150 mmdia 38 Supplying and Fixing of PN 1.6Butterfly Valve (Wafer Type) with S.G Iron Disc and confirming to IS:13095 complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets,etc as required of following sizes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .100mmdia 39 150mm dia 40 200mm dia Gear Operated 41 Supplying and Fixing of PN 16 Brass/GM Ball valves with screwed end, SS Ball including teflon tape etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .20 mm dia. 42 25 mm dia. 43 Supplying and fixing of SS 304 Single / Double headed oblique pattern hydrant landing valve (internal/external) with 75 / 100 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with ABS cap and chain and all accessories as per IS:5290-93 (Type-A) in cluding matching flange (14 mm thick),nuts, bolts, washers, gaskets,etc as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Single Headed with 75 mm Dia. Flanged Inlet 44 Supplying and fixing of flexible hose made with 100% polyester, black EPDM internal rubber lining with External coat of synthetic elastomer (IS:636, type-A)63 mm dia, 15 mtr. Long RRL hose pipe with instanteneous type 63 mm dia SS-304male and female couplings(IS:903) duly bound and riveted to hose pipes with copper rivets and SS wire etc. as required.Appropriate Test Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. 45 Supplying & fixing SS-304 Short Branch Pipeconforming to IS: 903:93 fitted with 20mm (nominal internal diameter)bore nozzle, for projecting water in form of solid jet. The Branch shall have 63mm Male Instantaneous Inlet, suitable for use with 63 mm size Fire fighting hoses. H.P. tested to 21 kgf/cm² for 2.5 minutes. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 46 Supplying and fixing first -Aid Fire hose reel Drum wall mounted swinging type with MS construction powder painted in post office Red, conforming to IS 884-1985 with upto date amendments, complete with the following as required.(A) Thermoplastic / Rubber Hose(B)20 mmdia UL, FM Bronze / SS nozzle with 5mm orifice (C)Drum and brackets for fixing the equipments on wall.(D) Connections from riser with 20/25 mm dia Brass/GM gate valves with screwed end and conforming to IS:778 Class-1through Forged steel Screwed Union & M.S. pipe. Etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .With 30 m x 20 mm Thermoplastic hose as per IS:12585 Type-2 and Bursting pressure 42 Kg/sqcm 47 Supplying and fixing Inlet Breeching Connection of CI body with Gun Metal male instantaneous inlet couplings with Inbuilt NRV, Drainage Connection with 50 mm Brass gate valvecomplete with PVC blank cap and chain as required for 150mm dia Outlet with 1 no. Matching Flange (Minimum 16 mm thick), nuts, bolts, washers, gaskets,etc as required of following Ways. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .2 way 48 Supplying and fixing of 1000 mm x 600 mm x 500 mm Outdoor application Fire Hose Cabinet made of 1.6 mm thick MS sheetDuly powder coated in red color externally and white internally with 6 mm thick glazeddoors with Expanded Metal 2 mm thick Jali including necessary locking arrangement suitable to accommodate External hydrant with butterfly valve, 2 Nos 15 Mtr. Long RRL Hose and 1 No. branch pipe on Existing Wall / Angle Iron Frame as required. (Cost of MS structure for mounting Frame is to be Paid Extra). All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 49 Providing and Fixing of 15 mm dia Bronze quartzoid bulb type sprinkler headswith Maximum working pressure 11.6 Kg / Sqcm and suitable for 68 degree centigrade rating standard response (UL Listed) chrome plated complete in all respect of the following type. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Pendant/ Upright type 50 Providing & fixing of UL listed 1.5 mm thick chrome plated Dual type MS Escutcheon platesfixed at junction of Sprinkler piping with the false ceiling. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 51 Providing & fixingsprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .1200 mm Long 52 Providing & fixing Stainless Steel pressure gauge with dial of 150 mm dia size and range 0 to 20 kg/sq.cmwith 3 / 8 BSP bottom entry , Ball valve , SS Syphon tube all fittings etc, dulycalibrated before installation in MKS and FPS units, Accuracy Level +/- 1% including Making Drilling in Existing MS PipeEtc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 53 SITC of UL 10th edition / EN54 / VDS certifiedAutomatic Floating Sensitivity type Analog addressable Multi criteria (two optical/Smoke sensor to reduce false alarm) detector with mounting base & LED etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 54 SITC of UL 10th edition / EN54 / VDS certified Addressable type fault isolator with base for isolating shorted, dewired and loose circuits between two successive fault, isolators with automatic resetting arrangementetc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 55 SITC of UL 10th edition / EN54 / VDS certified Addessable Manual Call point (MCP) with LED/ FIRE Indication Etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 56 SITC of UL 10th edition / EN54 / VDS certified Addressable sounder with strobe light,Loop Powered / Direct powered from FACP with sound level 90 dB and programmablefrom the panel etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 57 SITC of Response Indicatorfor indicating the activation of the Remotely located Detectorfor Addressable type Detectors Etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 58 SITC of UL 10th edition / EN54 / VDS certified Addressable control (input/output) modules/ Relay Module for shutting down lifts, Hooters, AHUs, Acknoledgement of Sprinkler system with potential free contact monitoring Etc. as Required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 59 SITC of UL 10th edition / EN54 / VDS certified Microprocessor based inteligent, Analogue addressable,modular, expandable networkableloop Fire Alarm Control Panel with each loop capacity of min 125 detectors per loop with total of 125 detectors & devices with Loop length up to 1 KM as per NFPA 72 approval. The Panel shall be able to give pin point location of addressable units via the address code for each unit. The Panel shall also be able to automatically switch off all control switches when-ever any Alarm is triggered. . The panel shall have 230 + 5 % volts power supply, Automatic battery charger 24V, sealed lead acid maintanence free battries sufficient for 24 hours normal working and then be capable of operating the system for 30 minutes during emergency condtion. Loop interface cards, communication module,LCD/LED unit to indicate Fire / Fault Signal of individual unit,inbuilt networking port(both RS485&Ethernet),Serial port for printer,two supervisory inputs,two position key switch and USB port for programming.including the cost of all accessories Etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .2 - Loop Panel 60 Add Extra for per Loop expansion beyond Two Loop 61 Add Extra for Graphics User Inteface (GUI) Software for programming the fire detection and voice alarm system through FACP/ PC. 62 Supplying and drawing Fire Resistant flexible / stranded bare copper conductor, PVC / XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS /EN 50288-7 in existingsurface or recessed PVC/ MS conduit/casing capping/ Cable tray / Open Duct making connections, testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for cables. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 2 x 1.5 Sq.mm Armoured With Outer Sheath in Red Color 63 Supply & Fixing of CO2 type Fire Extinguisher conforming to IS:15683:2018, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body , Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device ((Fusible plug and Rupture Disc Type), 1.0 Mtr. Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2, Horn with metallic thread connection, QR code for Product Traceability,including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificatefrom OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Capacity 4.5 Kg. 64 Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC typeFire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificatefrom OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 6kg 65 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR Short point (up to 3 mtr.) 66 Medium point (up to 6 mtr.) 67 Long point(up to 10 mtr.) 68 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR On board 69 Short point (up to 3 mtr.) 70 Medium point (up to 6 mtr.) 71 Long point(up to 10 mtr..) 72 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR. 25mm 73 50 mm 74 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR . 2 x 2.5 sq. mm. + 1x1.5sqmm 75 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 76 4 x 10.0 sq.mm 77 4 x 16.0 sq.mm 78 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. 79 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Single pole MCB (With B/C curve tripping Characteristics)6 A to 32 A rating 80 Four pole MCB (With B/C curve tripping Characteristics)50/63 A rating 81 80 A rating 82 Providing & Fixing of 240/415 V factory fitted RCBO with overload, short-circuit and earth leakage protectionwith ISI marked (IS12640-2)/ conforming to IEC 61009-1, breaking capacity 10 KA,provision for pad lock, min. Electrical operation 10,000 upto 63 A rating , minimum phase termination capacity of 35sq.mm. , IP 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR Four pole 100/300 mA sensitivity 63 A rating 83 Providing & Fixing of din rail mounting LED Indicating Lights with following description and configuration in existing distribution board / sheet including making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure A attached with this BSR. Red / Yellow / Blue / Green 84 Red-yellow-Blue 85 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Glazed door (Three phase) IK-09 and IP-43 with Metal end box 12 way 86 Providing & Fixing of following modular accessories as per PWD specification for electrical Works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating , includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure A attached with this BSR RJ-45, Cat 6 computer jack with shutter 87 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure A attached with this BSR 88 SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andOther parameters requiredas per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:- (a)Thickness of CRCA sheet shallbe 2.0 mm,cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided (b)complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting,pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side of panel.The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire. [c)Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar(>63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only.All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar/ Flexible wire for Interconnection between Main busbar and Switchgearis to be Paid Extra ) (d)Wiring between components within switchgear and Incoming / outgoing cableshall be done through the terminal block only. Direct connection shall not be permitted. Each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. For tap-offs, adjacent terminals with shorting strips shall be used. 10% Spare terminal blocks shall be provided. Wire identification on marking strip shall correspond to the designation of the wiring diagrams. All wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)All wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, Wiring between terminals of various devices shall be ‘point to point’ (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. (f)Floor mounted panel shall be mounted on Base frame of ISMCchannel size 100 x 50 x 5 mm( to be paid Extra ) (g) Tests: The insulation resistance (with 1000 V Megger) and High voltage Power frequency test (by applying a voltage of 2.5KV for one minute) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. The insulation resistance shall not be less than three megaohm. CT Secondary current injection test shall also be carried out. (h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI Test certificates to be submitted)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 89 Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Electrolytic grade Aluminium bus bar 6010 grade 90 Providing & Fixing of IS: 13875 & IEC :61326 confirming LED Digital type(up to 500) V range Volt meter / Direct- Ammeter /CT oertated ammeter/ Frequency meter / KWH meter / Multi Function Meter / Power analyzer of class 1 accuracyas per IS : 1248 of size 96mm x 96 mm including making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Three phase with universal Auxiliary supply + AMP + HZ + PF + KW + KVA + KVAR + KVARH + KWH + DUAL ENERGY+ ENERGY+THD-I, THD-V & RUN HRS + MD with RS485 91 SITC of3 /4pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator,line load interchangeability,designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree,pollution degree 3, having positive isolation capability, push(test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage690 V.provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.OEM shall have submitNABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. 4 pole MCCB With Thermal Magnetic release 400 Amp , 35 kA, adjustable O/L & adjustable S/C setting, 92 200 Amp , 25 kA, adjustable O/L & adjustable S/C setting, 93 125 Amp , 25 kA, adjustable O/L & adjustable S/C setting, 94 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR. 3.5 core*95 SQ MM 95 3.5 core*185 sqmm 96 4 core*10 sqmm 97 3.5 core*25 sqmm 98 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArmouredCoppercable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withelectrolytic gradeCopper made of copper rodsconfirming to IS 613-1964, of purity >99.7 %, round / flat strip armouring, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie)includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure A attached with this BSR. 2 core*1.5 sqmm 99 4 core*16 sqmm 100 4 core*25 sqmm 101 Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring,Compression Nut,heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with crimping tool, PVC tape as perIS 8337-1976offollowing size ofPVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 4 x 10.0 sq.mm 102 3.5 x 95.0 sq.mm 103 3.5 x 185.0 sq.mm 104 3.5 x 25.0 sq.mm 105 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) 106 Providing & Fixing of Heavy duty capacitor start, copper woundDouble ball bearing900/1400 RPM single phaseExhaustfan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 300 mm sweep(900/1400 RPM) 107 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure A attached with this BSR 5 step fan regulator 2 Module 360 dgree rotating 108 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1170mm(+/-10%) LED batten with min. lumen output 2200 lm 109 Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / SqaureSMD Mid Power LED Downlight with power coated die-cast aluminum housingwith UV Stabilized non yellowish Diffuser withBIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Minimum lumen output 1950 lm 110 Providing & Fixing of IP20, 2x2 LED Surface/ Recessedmounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection(Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 ,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Recessed Mounting Minimum lumen output 4200 lm 111 Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with HDPE, U/UTP (Unscreened/Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Outdoor Cable as per latest ammendments of ANSI/TIA/EIA-568 C.2 & ISO/IEC 11801 2nd Ed, The copper conductors should be balanced twisted in pairs, seperated by a cross divider & protected by LSZH PVCouter jacket of UV resistant. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. Should meet IEEE 802.3af & IEEE 802.3at for POE applications. Cable Should support Ethernet10GBASE-T according to the standards. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 112 Supply and Installation of unsheilded/360 degree sheilded Information outlets made of high impact plastic body with ABS, FR Grade halogen free material with provision for protection against dust in jack, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and complied with ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP) Specifications in existing modular/MS Boxes along with necessory connections as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Cat 6A, Sheilded Information Outlet 113 Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture ,material should bePC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Dual Aperture 114 Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568C.2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af / IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for long durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP).All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .3 Mtr 115 Supply & Installation of IP-20 & IK-08 , UL Listed Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet,Vertical Mounting Rail 1.6 MM with UMarking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, Set of 75 mm height 4 castors, 2 of which have brakes, Accessories like: 5 Nos of 19 1U Horizontal Cable manager, 2 Nos of vertical cable managers, 1 no. Keyboard Tray,4 Nos of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 2 No of 19 1U, mountable socket strips with 6 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .42 U Rack with Width 600 mm &Depth 800 mm 116 Supply & fixing MS powder coated stand suitable for 2.5/3.0/4.0 Tr outdoor type of Split/Ductable/Tower AC.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 117 SITC of 5 KVA 1 Phase Input, 1 Phase Output advance DSP controlled UPS with IGBT based rectifier, LCD display, double conversion / Digital Signal Processing UPS,with isolationtransformer,with 30 minute battery back up, with required cabling for incoming & outgoing connection (Approved makes: Emerson / Numeric / APC) 118 Supply, installation, testing and commissioning of Diagonal Size-55,Panel Type,Resolution-3840*2160 (4K UHD),Brightness-300 nit,Contrast Ratio-4000:1,Viewing Angle(H/V)-178/178,Response Time-8 ms,Display Colors-16.7M,Color Gamut-72%,Dynamic C/R-mega,Audio-Built in Speaker(10W + 10W),Input Type-HDMI 2.0 (2),HDMI 2.0 (2),USB 2.0 x 1,Stereo Mini Jack, HDMI/Audio(Common),Output Type-Stereo Mini Jack,Duty Cycle-16/7,Special features-UHD Signage with Built-in MagicInfo Lite,Haze 2%,Temperature Sensor,Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch), IP5x Rating, Auto Source Switching & Recovery,,LFD Home UI, Button Lock, Hot key option, Plug&Play (Initial Setting)External Control-RS232C(in) thru stereo jack, RJ45,Power Consumption(Max)-154 W/H OR LESS,Standby Mode Power-200*200,Operating Temperature-0 ℃ ~ 40 ℃,Humidity-10 % ~ 80.0 %,Safety-CE, UL & BIS,EMC-Class B.Make- Samsung/NEC/Christie 119 SITC of 2MP IR Indoor Dome Fixed Camera -1/3Progressive Scan CMOS, 2560 × 1440 at 20fps, 2.8/4mm Fixedlens, 0.0028 Lux at F2.0, AGC ON, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.Make: Hikvision,CP Plus, Dahua,honeywell Complete in all respect with all required accessories make is to beapproved by deparment .Test report / certificates ofmanufacturer which are to be needed is to be submitted by contractor 120 SITC of NVR 32 Channel 2 SATA having specification 32 IP Camera Supported Third-party network cameras supported Up to 8 Megapixels resolution recording Support 1-ch HDMI, 1-ch VGA, HMDI at up to 4K(3840x2160) resolution 4-ch network cameras can be connected with 40M/60M/80M incoming bandwidth Support dual-os to ensure high reliablility of system running Support various VCA detection alarm and VCA search Support H.265/H.264/MPEG4 video formats 2 SATA Port (2 Hard Disk supported upto 6 TB)Make : Hikvision,CP Plus, Dahua,honeywell . Complete in all respect with all required accessories make is to beapproved by deparment .Test report / certificates ofmanufacturer which are to be needed is to be submitted by contractor 121 Supply ,Installation ,Testing & Commissioning of 6TB Surveillance Class HDD for CCTV Recording ( Make:- WD , Seagate) 122 SITC of 4MP IR Outdoor PTZ Camera-1/2.8 Progressive Scan CMOS, 1920 × 1080 at 60fps, 4.8 mm to 153 mm, 32× Optical, 25x digital zoom, Color: 0.005 Lux at F1.6, B/W: 0.001 Lux at F1.6, ICR, ONVIF, support H.265,MJPEG, 120 dB WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Tripple individually configurable stream, 24 VAC & Hi PoE, IR range: 150m, Pan: 360° endless, Tilt: From -15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160°/s, Preset Speed: 240°/s, Tilt Speed- from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), IP66, IK10, Face Detection, Intrusion Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, UL, CE, FCC certified. Make: Hikvision,CP Plus, Dahua,honeywellComplete in all respect with all required accessories make is to beapproved by deparment .Test report / certificates ofmanufacturer which are to be needed is to be submitted by contractor 123 Supply, Installation, Testing and Comissioning of Rack mounted 19 1U, Cat6 24 Port loaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panelswith Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel. Etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .Modular Patch Panel Loaded with Cat -6A I/O 124 Supply , Installation, Testing and Comissioning ofManaged Layer-2 Intelligent 10/100 Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports / with min 2 SFP Giga Ports (provision for Fiber Giga connectivity) with related LAN Base Software including making connections etc as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 125 Supply, Installation, testing and commissioning of gooseneck microphone with table top stand, gooseneck length: 15 or better; Polar pattern: Cardioid / hypercardioid / supercardioid; RFI Sheilding; S/N Ratio: 65 dB or better; Max SPL for 1% THD: 107 dB or better; Frequency response: 50 Hz to 17kHz or better; LED Indication; ON/OFF Switch. complete in all respect with all required test report . Make :-Sennheiser / shure /Televic and make is to be approved by department. 126 Supply, Installation, testing and commissioning of Instrument microphone unidirectional with type of transducer: Dynamic; Polar Pattern: Cardioid / hypercardioid / supercardioid; Frequency Response: 50Hz to 14kHz or better; Sensitivty: Min 1.8 mV or better; Nominal Impedance: < 360 or better. with suitable stand complete in all respect with all required test report . Make :-Sennheiser / shure /Televic and make is to be approved by department. 127 Supply, Installation, testing and commissioning of Wirelesshandheldmicrophone with FM Modulation; Pre programmed Selectable Frequencies per Band: 12 or better; Polar Pattern: Cardioid / Hypercardioid / Supercardioid; RF Freq. Range: 518 MHz to 865 MHz or better; THD: <0.9% or better; RF Power: 20mW or better; S/N Ratio: >110 dB or better.complete in all respect with all required test report . Make :-Sennheiser / shure /Televic etc and make is to be approved by department. 128 Supply, installation, testing & Commissioning ofof digitalmixer for live stage mics Fader Configuration:- 32 + 1,Input Channels:- 48 (40 mono + 2 stereo + 2 return,(Master)Aux Buses:-20 (8 mono + 6 stereo),Input channel functions:-8 DCA Groups,Inputs:-32 mic/line (XLR/TRS combo) + 2 stereo line (RCA pin),Outputs:-16 (XLR),DSP:-8 Effects + 10 GEQ,USB:-34x34 USB Audio Interface, 2-track recording via USB Storage Device,Total harmonic distortion:-Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz),Frequency response:-+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT,Dynamic range:-110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min,Equivalent input noise:-–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter),Residual output noise:-–85 dBu, ST master off (Measured with an A-Weight filter),Crosstalk:-–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.complete in all respect with all required test report . Make :-Yamaha/allen & heath/ mark etcand make is to be approved by department. 129 Supply, installation, testing & Commissioning ofofdigital audio DSP with 32-bit fixed/floating-point DSP 456 MHz/ARM Cortex-A8 600 MHz processor or better with following features and specifications are required:The audio DSP shall have 12 balanced inputs and 8 balanced output channels for microphone or line-level analog audio signals, each independently controllable . The DSP shall have Dante® digital audio networking up to 64 input and 64 output channels, an Ethernet connection for control and programming on an RJ-45 jack, USB audio and 8 digital channels on an RJ-45 jack. The audio DSP shallinclude configurable signal processing, likesignal routing and mixing, equalization, filtering, dynamics, delay, room combining, as well as control, monitoring, and diagnostic tools. The audio DSP shall control and proxy allexpansion devices and other Dante® endpoints.It shall have following specs : Frequency Response-18 Hz to 20 kHz (+0.8 dB/-0.2 dB ref 1 kHz)THD+N < 0.003% @ +4 dBu (A-weighted/20 Hz to 18 kHz),Channel Separation (Crosstalk) < -105 dB at +4 dBu 1 kHz input signal,Dynamic Range > 115 dB, A-weighted 20 Hz – 20 kHz, analog input to analog output. complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 130 Supply, installation, testing & Commissioning ofof Digital Dante Amplifier with Max output power of 4x1200W@4-8Ohms, 70V or 100V or bridged mode output power of 2x3000W@4ohms. Frequency response of 20 Hz - 20 kHz, SNR of >110 dB(A and THD+N < 0.1%. With Multiple channel metering LED and attenuation controls. PEQ, band pass, Spkr EQ, limiter, delay. Maximum input level 20 dBu. 4 Digital channels via Dante, with Euroblock, 8-pin connectors for Analog outputs. Software and hardware controlled. Sample rate 24-bit, 44.1 kHz – 192 kHz.complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 131 Supply, installation, testing & Comissioning of 4 channel power amplifier with total of 2400W power and power sharing feature for Asymmetric power allocation. Shall support Dante Digital as well as Analog line level audio inputs and GPIO connections for muting. Power output: Upto 4x600W @ 4 and 8 ohms, upto 4x750W @ 2ohms, SNR: 108dB(A) or better, THD+N: <0.1 %, Crosstalk (1 kHz): -70dB or better, A/D and D/A converters: 24-bit, 48 kHz Sample rate converter: 24-bit, 44.1 kHz – 192 kHz Input-to-output signal routing: 4 × 4 matrix. signal processing: Matrix mixer, 5-band PEQ, array EQ, band pass, Spkr EQ, limiter, delays, Programmable speaker EQs Input impedance : 20 kΩ, Status indicators: metering LEDs, system status LEDs, power status LEDs, Protections: Thermal, excess high/low AC mains voltage, DC, high‑frequency, output short‑circuit, inrush current, clip, peak, etc. Cooling system: variable-speed fan, front-to-back airflow. complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 132 Supply, installation, testing & Commissioning ofof intregrated low impedence Class D Amplifier with output of 2 x 50 W @ 4 Ω, 2 x 25 W @ 8 Ω ; Frequency Response - 40 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz); THD+N - ≤0.3 % (at full rated power) ; Channel Separation (Crosstalk) - ≤-60 dBV (below rated power, 1 kHz); A/D and D/A Converters- 24-bit / 48 kHz; Audio Latency - 10.4 ms - (any input to speaker output or aux output) ; Maximum Input Level : +10 dBV or better. 1 balanced page input, I balanced mic/line input, 2 unbalanced line; built in loudspaker EQs. Shall include output for expansion amplifier and remote controller (Wired) for source as well as volume control complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 133 Supply, installation, testing & Commissioning ofof intregrated high impedence Class D Dual Zone Amplifier with output power of 2 x 120 W @ 70/100 V ; Frequency Response - 55 Hz - 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz) ; THD+N - ≤1 % (at full rated power); Channel Separation (Crosstalk) - ≤-60 dBV (below rated power, 1 kHz); A/D and D/A Converters- 24-bit / 48 kHz; Audio Latency - 10.4 ms - (any input to speaker output or aux output); THD <0.3% at rated power. Channel Separation ≤ –60 dBV (below rated power, 1 kHz), Dynamic range > 88 dB.Maximum Input Level : +10 dBV or better. 1 balanced page/priority input, 3 unbalanced line inputs; built in loudspaker EQs. Shall include output for expansion amplifier and remote controller (Wired) for source as well as volume control complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 134 Supply, installation, testing & Comissioning of Trapezoidal arrayable Point Source loudspeaker. The louspeaker shall meet the following criteria: Single 14 LF driver or dual 10-inch with multiple MF/HF drivers (More than 4). Biamplified operation with Individual Module free field Frequency Range (-10dB) of 55Hz - 18kHz or better & Continuous Power Handling of >= 750W LF + 150W MF/HF. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 130 or better. It should have Horizontal near dispersion pattern of 60º or better, vertical dispersion of the module shall be 70 degrees or better. The array shall have a stack of minimum of 3 or more speakers.The Loudspeaker shall have a weather rating of IP55 complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 135 SITC of OEM flying array frame and other necessary hardware for suspending main speaker arrays. All necessary hardware to be included to achieve a safety factor of 8:1 or better complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechniketc and make is to be approved by department. 136 Supply, installation, testing & Comissioning ofbiamped, coaxial two-way point source loudspeaker with a single 12-15 LF driver and compression driver with 3 or better Voice coil. Frequency Range (-10dB) of 60Hz - 20kHz or better& long term Continuous Power Handling of 300W (Low frequency) and 45W for High Frequency driver or better. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 131 or better. It should have Horizontal dispersion pattern of 110º or better, vertical dispersion of the loudspeaker shall be 60 degrees or better. The loudspeaker shall be enclosed in a baltic birch plywood enclosure with perforated steel grille complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 137 Supply, installation, testing & Commissioningof suspension bracket that shall be designed to provide single point suspension for the loudspeakers and mounts along the center of gravity. The bracket shall have multiple single-point suspension attachment points to allow incremental angle adjustment from 35 degrees of downtilt and ranging to 25 degrees of uptilt complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 138 Supply, installation, testing & Commissioning of a single 18 subwoofer.The louspeaker shall meet the following criteria: usable Frequency Range (-10 dB) of28 Hz - 200Hz or better. It should have an axial Sensitivity of > = 92dB (1W/1m) or more delivering a free field Max. Calculated SPL(peak) of>=127 db or better. The loudspeaker should have a nominal impedance: 4/8 ohm and continuous Power Handling of 750W or more;Complete with installation accessories as per the site requirement complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 139 Supply, installation, testing & Commissioning ofTwo-way Small Format high SPL IP55 rated (as per IEC 60529) all weather surface mount loudspeaker. The louspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of90 Hz - 18 kHz or better; Nominal Dispersion : 100°H x 100°V;Power handling of 400W peak or more; Sensitivity : 90 dB and the Max SPL : 118dB Peak or better; Nominal impedence of 8 ohms and Integral multi-tap Transformer with selectable tap settings of 10/20/40/80W@70V & 100V. The loudspeaker system shall be comprised of a Powder-coated finish stainless steel grille with Two-part spray polyurea coating Enclosure;Single 5.25-inch woofer; Single 2-inch voice coil high-frequency compression driver; U bracket shall be included complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 140 Supply, installation, testing & Commissioning of Two-way Small Format high SPL IP55 rated (as per IEC 60529) all weather surface mount loudspeaker. The louspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of80 Hz - 18 kHz or better; Nominal Dispersion : 90°H x 60°V (rotatable Horn); Power handling of 800W peak or more; Sensitivity : 93 dB; Max SPL : 122dB Peak;Nominal impedence of 8 ohms and Integral multi-tap Transformer with selectable tap settings of 10/20/40/80W@70V & 100V.The loudspeaker system shall be comprised of a Powder-coated finish stainless steel grille with Two-part spray polyurea coating Enclosure;Single 8-inch woofer; Single 2-inch voice coil high-frequency compression driver; U bracket shall be included complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etcand make is to be approved by department. 141 Supply, installation, testing & Commissioning ofFull range IP55 rated indoor/outdoor surface mounted music and PA loudspeaker. The louspeaker shall meet the following perfomance criteria: Usable Frequency range (-10dB) of 83Hz to 19kHz; Power handling of 64 Watt peak; Nominal dispersion of 130°(H) × 130°(V); Sensitivity of 85 dB SPL and Max SPL of 103 dB SPL peak; Nominal impedence of 16 ohms and Integral multi-tap Transformer with selectable tap settings of 2/4/8/16W@70V & 100V.The loudspeaker system shall be comprised of a 2.25-inch woofer; enclosed in engineered-plastics and a powder-coated tamper-resistant steel grille. UL-1480 rated and EN54-24 compliant for Life safety/VA applicatons.complete in all respect with all required test report . Make :-Bose / L Acoustic / d&b audiotechnik etc and make is to be approved by department. 142 Supply, installation, testing & Commissioning ofDisplay Size:- 20.99 x 11.59 ft.Indoor led video walll Pixel Picth-3mm:-Pixel Pitch-3 mm or better COB/COS/FlIP CHIP,Configuration-SMD 3-in-1 LED Type withCOB/COS/FlIP CHIP,Pixel Density-105000pixels/m2 or better,Brightness Calibrated-800 cd/m2 or better,Dimming Capability-0-255 Levels or higher,Contrast Ratio-3000:1 or better,3000:1 or better-1920 Hzor better,Color Processing-14-bit or better,Colors-4.4 Trillion or better,Half Gain Viewing Angle- H: ± 80°or better, V: ± 80°or better,Service Access-Front/Rear,IP Grade-IP30 / IP30 . with Power Distribution Unit and controler complete in all respect with all required test report . Make :-Delta / NEC /Barco. etc and make is to be approved by department. 143 Supply, installation, testing & Commissioning of Digital Interactive Podium features a robust metallic frame with a wooden top and a 21.5-inch Full HD interactive display (combining electromagnetic and capacitive touch technologies) equipped with a cordless, pressure-sensitive electromagnetic induction (EMR) battery-less pen. It should be motorized tilting mechanism for the interactive panel, a gooseneck microphone with mount, a keyboard and mouse tray, and storage space for AV equipment. The interactive display offers Full HD resolution (1920x1080), IPS LED technology, a 16:9 aspect ratio, 300 ± 30cd/㎡ brightness, and a 1000:1 contrast ratio support up to 16.7M colours. Input/output terminals HDMI x 1, VGA x1, x DVI x 1, USB In x 1, DC JACK X A. Top connectivity plate provides HDMI, 2 x USB ports, and a power socket with On/Off switch for external device connectivity. It should be equipped with a built-in 4x2 HDMI Matrix Switcher supporting 4K@60Hz (4:4:4, 8-bit), 16-bit Deep Color, HDR (High Dynamic Range), 3D content, and HD audio as per HDMI 2.0 specifications also features an audio de-embedder for seamless audio connectivity.complete in all respect with all required test report . Make :-uniluman / AAH /Televic etc . and make is to be approved by department. 144 Supply, installation, testing & Commissioning ofHDMI 2.0 HDBaseT Extension Set, Extend HDMI 2.0 signals up to 4K@60Hz / 4:4:4 up to 70m (4K 40m / 1080P 100m), Complete set Includes TX, RX, power supply, and IR flasher/emitter, Extends bi-directional IR. Flexible PoC (Power on either end), Supports HDR10, HDCP 2.2 compliant, Flexible power design (use power supply at TX or RX)complete in all respect with all required test report . Make :-.Liberty/kramer/Extron etc and make is to be approved by department. 145 Supplyand fixingof HDMI Cable(with connectors)for connecting media devices to playback display such as HDTVs, projectors. HDMI Cable havingSolid copper conductors and full metal jacket shielding for durability and high-performance connectivity, Supports Ethernet, 3D, 4K video and Audio Return Channel (ARC) and meets the latest HDMI standards make Technxt, honeywellandother equivalent make matching with above specifications. HDMI Cable HDMI Cable 15 Mtr 146 HDMI Cable 5 Mtr 147 Supply and laying speaker cable of IS/ISO 9001 CERTIFIED COMPANY made following size 2 core twin twistedmulti stranded electrolytic grade copper conductor, overall PVC insulated and armoured cable (Blue colour) on surface/ above false ceiling including cost of GI spacers, saddles etc. as required. For additional technical parameters of product / work refer Annexure A attached with this BSR 2.5 Sq.mm 148 SITC of 18 x 10w LED Par Light RGBW, Beam Angle 25° complete withLED source from Lumi led / Seoul / Nichia or reputed make (LM80 to be provided) RGBW 3W Lamp source x 54 Pcs DmX 512 dimming with 8 ChannelHigh Bright Red, Green, Blue, White LED’s Source Unlimited Colour Mixing through DmX 0 ~ 100% Linear dimming In built presets for different colours Strobe Mode 20 times/Sec Data DmX through 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections High precision colours, IP20 protectionPowder coatedBlack finish housing Having Sound Control & Master Slave Auto Run ModeIlluminate theIndoor stage with unlimited colour effects Rigidly built pressure die-casted Aluminium body.RDM Control options with latest technology (RDM ID to be specified), Certificates from NABL Accredited laboratory Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012CE Certification , Brand embossed impact on the light body for genuine product. complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 149 SITC of 200W LED Profile Spot 19 Degree Light complete with, 3200K CCT Colour Temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided)CRI & TLCI above 95 Strobe option Adjustable 1 ~ 25 times / Sec4 Kinds of dimming curves, Black finish housingManual Focus with 4 Beam shaping cutters Efficient and well-designed Lamp reflector Efficient Copper tube based Heat Sink for Heat Dissipation Sleek and Unique Designed Light weight body Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modes IP20 protection having Lux @ 3 Mtr above 9066 suitable to illuminate the key presenter or talent on stage. illuminate the key presenter or talent on stage. RDM Control options with latest technology (RDM ID to be specified) LM79 Certificates from NABL Accredited laboratory Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification c Brand embossed impact on the light body for genuine product. complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 150 SITC of 150W High Quality LED Parcan Light complete with,Lamp source 3200K CCT Colour temperature CRI & TLCI Values above 95 COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 3 channel control Beam Angle of 11˚ / 25˚ / 35˚Total Power Consumption of 160WHigh quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100% Fuse and Internal safety protectionsStrobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX , Black powder coated body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012CE Certification compliant Certificates from NABL Accredited laboratory.Brand embossed impact on the light body for genuine produc. complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 151 SITC of Moving Head Beam effect light 12R BaseHigh bright long throw beam with linear zoom rangeZoom range from o to 3.8 Degree Lamp Source: Yodn 280W 12R Arc Lamp Total Power Consumption of 450W, Electrical: AC 100-240V, 50/60Hz 16 Channel DmX Control Color System:1 color wheel+14pcs,Prism：8prism+48prism with rotation effect 16 Bit Dimmer Control Gobos System: 16+1pcs gobos. Double chip Stroboscopic (0.5 ~ 9 times /SEC),Pan Angle 540°, Tilt Angle 270° IP20 rated product. Electrical: AC 100-240V, 50/60Hz. complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 152 SITC of 400W LED Blinder Light 30 Degree complete with 3200K CCT 4x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 8 Channel modes CRI & TLCI Value > 90 , Strobe option Adjustable 1 ~ 25 times / Sec Variable, Beam Angle 30 Degree Total Power Consumption of 410W 11.7KHz Refresh Rate,In built preset’s for effects,Fuse and Internal safety protections,Active Cooling with Low Noise Fan, 5 Pin XLR for DmX,High quality well designed inbuilt reflector, Flicker Free 100% for Tv & Film Cameras, Black finish housing, IP20 protection, Having Strobe option and smooth dimming, illuminate Stage with uniform light intensity levels. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012CE Certification , Certificates from NABL Accredited laboratory complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 153 SITC of 200W LED Fresnel Light having COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) 3200K colour temperature High quality uniquely designed Fresnel Lens CRI,TLCI and R9 value above 95 LED COB Based SourceNo Multiple Shadows – Single Source illumination Total Power Consumption of 210W Linear dimming 0 ~ 100% Adjustment Flicker Free for High FPS, Power AC100-240V, 50HZWorking Temperature - +40° ~ -30° Active Cooling with Low Noise Fan complete in all respect with all required test report . Make :-.Leksa,Markrich,Aultra,Philips,Bajaj,Surya and make is to be approved by department. 154 SITC of Dimming system consist of Opto isolated RDM enabled DmX splitter unit, 8 Output channels. Dimming In and out junction box 1 way with 5 Pin DmX XLR Male-Female socket, DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections & Male Termination Connector 5 Pin. 5 Core DmX Cable with Sheathed housing on the cable, low noise suitable to transmet DmX signal complete in all respect 155 SITC of DmX Touch Screen based controller having 7” Multi touch screen option 2 DmX Outlets 5 Pin XLR’s, 512 Channels each, Optically isolated outputs, 4 Smooth Encoders for control operation of attributes, Backlit keys, 12 Fader Stacks, 600+ Playbacks, 350+ Group saving, 350+ Presets, User defined shape effects, Macro saving options, External Midi timecode options, Internal clock, Shortcut user interfaces, Master fader, Blackout Key under Master fader, Numerical keypad for the light command entry inbuilt embedded within controller, USB interface, Scene saving options, Show saves and load save features, custom built user interface library for fixture files complete in all respect 156 Supply, installation, testingand commissioning of lighting control cable (DMX cable ) with exceptional durability and flexible construction .Cable to meet Visit standards for DMX 512. Cable to be all weather proof , extra flexible jacket material that are tough & abrasion resistant .Cable to be properly terminated / connected using standard connectos . Make :- Belden/Max etc and make is to be approved by department 157 SITC of Aluminium O Type clamp made up of high grade aluminium having thickness not less than 5mm suitable for round tubes of dimension varying from 40 to 55mm outer diameter, provided with fixture mounting 25mm M8 bolt and wing nut, minimum 100KGs of safe working load, 40mm bolt and wing nut for pipe locking complete in all respect 158 SITC of Light Fixture dual safety, Chain made up of GI wire ropeBundled and twisted together Having load bearing capacity above 200 Kgs Sleeve on the rope. Carabiner Clip complete in all respect 159 SITC of High quality power junction box 4 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm )Total Max Rating 10A, 250V A.C20˚C to +70˚C Operating TempMoldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall / floor fixing complete in all respect 160 SITC of High quality power junction box 2 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ),Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating TempMoldings: Nylon,Flammability Rating UL94V-0Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing complete in all respect 161 SITC of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing complete in all respect 162 SITC of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection &electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing complete in all respect 163 SITC of DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR Female Socket & 1 No. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding.Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixingcomplete in all respect 164 SITC of 48-way Power Marshalling Box made up of MS Sheet metal fabricated housing black powder coated and ivory connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable sizecomplete in all respect 165 Providingexperienced and Highly skilled/skilled/ semi-skilled/Un Skilledlabour for electric repair/ maintenance / operation of Air conditioning/Air cooling/Fire fighting/Lift/DG set/CCTV/EPABX or any other electromechanical systems as per requirement (one shift of 8 Hrs per day for 26 Working Days in a month) Highly skilled Labour 166 skilled Labour

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	01-04-2025	Date Extend	Date	15-04-2025

INR 7500 /-

INR 1031800.0 /-

INR 5.15 Crore /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB