|
| 1 | Lower - Housing |
| 2 | Fitting Plate for Air Seal Assembly (Mark No. 4 Dwg No. C-10-32R-5788) ( 1Set = 1 Mill Qty.) |
| 3 | Complete Hub Skirt Assembly |
| 4 | Middle Housing |
| 5 | Grinding Table Upper Ring(THK 20 mm) |
| 6 | Deflector Assembly (Dwg No.10-32R-6724 R1) |
| 7 | Complete Deflector Assembly duly installed tiles without Liners with BOLT, NUT M16X40 spot weldedfor top liners and bottom hard chrome liners |
| 8 | Taper Cup (Part no.N67-700-1181-1 , Mark No. 08) |
| 9 | Ceramic Liner Cover (Part no.N67-700-1181-3 , Mark No. 09) |
| 10 | Washer (Part no.N67-700-1175-1 , Mark No. 32) |
| 11 | Ceramic Liner Cover (Part no.N67-700-1174-2 , Mark No. 31) |
| 12 | Ceramic Liner (Part no.N67-700-1174-1 , Mark No. 30) |
| 13 | Set Screw (Part no.170-255-020-2 , Mark No. 103) |
| 14 | Bolt(Part no.N67-700-1173-2 , Mark No. 28) with Nut (M16) ( 1 Set = 1/3 Mill Qty) |
| 15 | Complete Set of Tiles for Deflector with weldable/taper plug and ceramic cap ( 1 Set = 1/3 Mill Qty.) |
| 16 | RJ Cover (DWG No. C-10-32F-61306) |
| 17 | Journal Gap Bolt Bushing (dwg. mark no 2) |
| 18 | Piston Housing (dwg mark no 3) |
| 19 | Bushing Retainer (dwg mark no 4) |
| 20 | Lock Plate (dwg mark no 8) |
| 21 | Lock Plate (dwg mark no 9) |
| 22 | Lock Plate (dwg mark no 10) |
| 23 | Roller Lift gauge (dwg. mark no 14) |
| 24 | Roller Lift gauge Fitting Plate(dwg. mark no 15) |
| 25 | SHIM(Piston Bush) (dwg. mark no18) ( 1 Set = 1/3 Mill Qty) |
| 26 | Dust Seal for Roller Tensioning System (mark no 13) 1 Set = 1/3 Mill Qty.) |
| 27 | Classifier |
| 28 | Complete Set ofTiles for Center Cone and Center Feed Pipe with weldable plug and ceramic cap ( 1 Set = 1 Mill Qty) |
| 29 | Outlet Ring ( Classifier) MOC Hardox: 400 (suitably in 3-4 segments) |
| 30 | Slide Outlet (Classifier) MOC Hardox 400 (suitably in 3-4 segments) |
| 31 | Complete Outlet Ring Drive Assembly |
| 32 | Centre cone support pipe with flange duly installed tiles.( 3 Nos = 1 Mill Qty.) |
| 33 | Center Feed Pipe Outlet ( Classifier) |
| 34 | End Cup (Thrust) |
| 35 | End Cup ( Free) |
| 36 | End Cup BUSH Locking Set Screw (MHI Dwg no N67-700-6177) (1 set = 1 Mill Qty) |
| 37 | R J Assembly |
| 38 | Seal Kit Complete Set for RJA ( 1 Set = 1 RJA) |
| 39 | Upper Plate |
| 40 | Stop Plate |
| 41 | Journal Head |
